| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Device tree nodes for RTC devices should be called "rtc", so fix up some
instances where that wasn't the case.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This driver uses GPIO descriptors to drive the touchscreen RESET line. In
the existing device trees this has in conflict with intution been flagged
as GPIO_ACTIVE_HIGH and the driver then applies the reverse action by
driving the line low (setting to 0) to enter reset state and driving the
line high (setting to 1) to get out of reset state.
The correct way to handle active low GPIO lines is to provide the
GPIO_ACTIVE_LOW in the device tree (thus properly describing the hardware)
and letting the GPIO framework invert the assertion (driving high) to a
low level and vice versa.
This is considered a bug since the device trees are incorrectly
mis-specifying the line as active high.
Fix the driver and all device trees specifying a reset line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201104153032.1387747-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
1. Replace boiler plate licenses texts with the SPDX license
identifiers in Toradex i.MX7-based SoM device trees.
2. As X11 is identical to the MIT License, but with an extra sentence
that prohibits using the copyright holders' names for advertising or
promotional purposes without written permission, use MIT license instead
of X11 ('s/X11/MIT/g').
3. Replace "Toradex AG" with "Toradex" in the Copyright notice.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Replace boiler plate licenses texts with the SPDX license identifiers in
Colibri iMX7 DTS files.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Make sure that the priority of the RTCs is defined.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add touch controller that is connected over an I2C bus.
It is disabled by default because the pins are also used for PWM,
which is the standard use for colibri boards.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add wakeup GPIO key which is able to wake the system from sleep
modes (e.g. Suspend-to-Memory).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Colibri Evaluation Carrier Board provides a MCP2515 CAN
controller connected via SPI. Note that the i.MX 7 provides
an internal CAN controller which is much better suited for CAN
operations. Using the MCP2515 with a Colibri iMX7 module is
mainly useful to test the SPI interface.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The usdhc1 controller instance is used to provide the default
SD/MMC capabilities of the Colibri standard. The IO pins are
supplied to the SoC on the module whereas the SD-card is powered
by the Carrier Board supply.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Colibri default which enables USB Host power is not necessarily
tied to the OTG2 controller, some carrier board use the pin to
control USB power for both controllers. Hence name the pinctrl
group more generic.
Also move the regulator to the generic eval-v3 device tree since
the regulator is always on the carrier board. In the Colibri iMX7S
case the regulator is just not used. This allows to reuse the
regulator in a upcoming SKU Colibri iMX7D 1GB with eMMC.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
All Toradex Carrier Boards use a st,m41t0 compatible RTC. Compared
to a st,m41t00 this RTC has also an oscillator fail bit which allows
to detect when the RTC lost track of time.
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Model the Carrier Board power distribution by adding a fixed 3.3V
and 5V regulator. The 3.3V regulator is connected to the backlight
as well as the display supply. The 5V regulator is used to supply
USB VBUS.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
To make use of the new eLCDIF DRM driver OF graph description is
required. Describe the display using OF graph nodes.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move SD-card definition to module level. While at it, also disable
write-protect since the Colibri standard does not define a pin for
SD-Card write-protection.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the Computer on Module Colibri iMX7S/iMX7D along
with the development/evaluation carrier board device trees. Follow
the usual hierarchic include model, maintaining shared configuration
in imx7-colibri.dtsi and imx7-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
