Age | Commit message (Collapse) | Author | Files | Lines |
|
Pull ARM Device-tree updates from Olof Johansson:
"Besides new bindings and additional descriptions of hardware blocks
for various SoCs and boards, the main new contents here is:
SoCs:
- Intel Agilex (SoCFPGA)
- NXP i.MX8MM (Quad Cortex-A53 with media/graphics focus)
New boards:
- Allwinner:
+ RerVision H3-DVK (H3)
+ Oceanic 5205 5inMFD (H6)
+ Beelink GS2 (H6)
+ Orange Pi 3 (H6)
- Rockchip:
+ Orange Pi RK3399
+ Nanopi NEO4
+ Veyron-Mighty Chromebook variant
- Amlogic:
+ SEI Robotics SEI510
- ST Micro:
+ stm32mp157a discovery1
+ stm32mp157c discovery2
- NXP:
+ Eckelmann ci4x10 (i.MX6DL)
+ i.MX8MM EVK (i.MX8MM)
+ ZII i.MX7 RPU2 (i.MX7)
+ ZII SPB4 (VF610)
+ Zii Ultra (i.MX8M)
+ TQ TQMa7S (i.MX7Solo)
+ TQ TQMa7D (i.MX7Dual)
+ Kobo Aura (i.MX50)
+ Menlosystems M53 (i.MX53)j
- Nvidia:
+ Jetson Nano (Tegra T210)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (593 commits)
arm64: dts: bitmain: Add UART pinctrl support for Sophon Edge
arm64: dts: bitmain: Add pinctrl support for BM1880 SoC
arm64: dts: bitmain: Add GPIO Line names for Sophon Edge board
arm64: dts: bitmain: Add GPIO support for BM1880 SoC
ARM: dts: gemini: Indent DIR-685 partition table
dt-bindings: hwmon (pwm-fan) Remove dead "cooling-*-state" properties
ARM: dts: qcom-apq8064: Set 'cxo_board' as ref clock of the DSI PHY
arm64: dts: msm8998: thermal: Restrict thermal zone name length to under 20
arm64: dts: msm8998: thermal: Fix number of supported sensors
arm64: dts: msm8998-mtp: thermal: Remove skin and battery thermal zones
arm64: dts: exynos: Move fixed-clocks out of soc
arm64: dts: exynos: Move pmu and timer nodes out of soc
ARM: dts: s5pv210: Fix camera clock provider on Goni board
ARM: dts: exynos: Properly override node to use MDMA0 on Universal C210
ARM: dts: exynos: Move fixed-clocks out of soc on Exynos3250
ARM: dts: exynos: Remove unneeded address/size cells from fixed-clock on Exynos3250
ARM: dts: exynos: Move pmu and timer nodes out of soc
arm64: dts: rockchip: fix IO domain voltage setting of APIO5 on rockpro64
arm64: dts: db820c: Add sound card support
arm64: dts: apq8096-db820c: Add HDMI display support
...
|
|
Some USB peripherals draw more power, and the sourcing regulator
take a little time to turn on. This patch fixes an issue where
some devices occasionally do not get detected, because the power
isn't quite ready when communication starts, so we add a bit
of a delay.
Fixes: 1c207f911fe9 ("ARM: dts: imx: Add support for Logic PD i.MX6QD EVM")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The main 3.3V regulator sources a series of additional regulators.
This patch adds a small delay, so when the 3.3V regulator comes
on it delays a bit before the subsequent regulators can come on.
This reduces the inrush current a bit on the external DC power
supply to help prevent a situation where the sourcing power supply
cannot source enough current and overloads and the kit fails to
start.
Fixes: 1c207f911fe9 ("ARM: dts: imx: Add support for Logic PD i.MX6QD EVM")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The original submission had functional audio out and was based
on reviewing other boards using the same wm8962 codec. However,
the Logic PD board uses an analog microphone which was being
disabled for a digital mic. This patch corrects that and
explicitly sets the gpio-cfg pins all to 0x0000 which allows the
analog microphone to capture audio.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Commit 6d4cd041f0af ("net: phy: at803x: disable delay only for RGMII mode")
exposed an issue on imx DTS files using AR8031/AR8035 PHYs.
The end result is that the boards can no longer obtain an IP address
via UDHCP, for example.
Quoting Andrew Lunn:
"The problem here is, all the DTs were broken since day 0. However,
because the PHY driver was also broken, nobody noticed and it
worked. Now that the PHY driver has been fixed, all the bugs in the
DTs now become an issue"
To fix this problem, the phy-mode property needs to be "rgmii-id", which
has the following meaning as per
Documentation/devicetree/bindings/net/ethernet.txt:
"RGMII with internal RX and TX delays provided by the PHY, the MAC should
not add the RX or TX delays in this case)"
Tested on imx6-sabresd, imx6sx-sdb and imx7d-pico boards with
successfully restored networking.
Based on the initial submission from Steve Twiss for the
imx6qdl-sabresd.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Soeren Moch <smoch@web.de>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Adam Thomson <Adam.Thomson@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The EVM consists of a system on module (SOM) and baseboard, and LCD.
This patch adds a DTSI file for the SOM and baseboard separately,
then a wrapper to combine them and specify processor type and a
LCD information.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|