summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/imx25-karo-tx25.dts
AgeCommit message (Collapse)AuthorFilesLines
2014-05-16ARM: dts: Karo TX25: use hardware eccSascha Hauer1-0/+2
We should use hardware ecc on i.MX. While at it, add the optional nand-bus-width property. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: Karo TX25: Add phy reset gpio and supply for FECSascha Hauer1-0/+18
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: Karo TX25: Add pinctrl nodesSascha Hauer1-0/+53
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: Add stdout-path property to i.MX boardsSascha Hauer1-0/+4
This adds the stdout-path property to various i.MX boards. Values of the property have been taken from barebox, so they should be correct. Also, the older linux,stdout-path property is converted to stdout-path. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2013-04-09ARM: imx: use #include for all device treesShawn Guo1-1/+1
Replace /include/ (dtc) with #include (C pre-processor) for all imx DT files, so that gcc -E handles the entire include tree, and hence any of those files can #include some other file e.g. for constant definitions. This allows future use of #defines and header files in order to define names for various constants, such as pinctrl settings. Use of those features will increase the readability of the device tree files. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-02-10ARM: dts: imx25-karo-tx25: Put status entry in the endFabio Estevam1-1/+1
Just to keep consistency with other dts files, place 'status' entry as the last one. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-02-10ARM: dts: imx: use nodes label in board dtsShawn Guo1-19/+11
Following omap3-evm.dts way, it changes all imx dts files to use label in board dts to refer to nodes defined by soc dtsi. Thus, the board dts files become easier to read and edit with the least indentation levels. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-11-12ARM i.MX: Add Ka-Ro TX25 devicetreeSascha Hauer1-0/+44
Basic support for the Ka-Ro i.MX25 based TX25 board. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Cc: Lothar Waßmann <LW@KARO-electronics.de>