Age | Commit message (Collapse) | Author | Files | Lines |
|
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations http www opensource
org licenses gpl license html http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.383790741@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Boards based on imx23 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx23.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
dtc has new checks for SPI buses. Fix the warnings in node names and
unit-addresses.
There's over 100 warnings for FSL boards, a few examples:
arch/arm/boot/dts/imx28-duckbill-2-spi.dtb: Warning (spi_bus_bridge): /apb@80000000/apbh@80000000/ssp@80014000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/imx53-ppd.dtb: Warning (spi_bus_bridge): /soc/aips@50000000/spba@50000000/ecspi@50010000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/imx6dl-colibri-eval-v3.dtb: Warning (spi_bus_reg): /soc/aips-bus@2000000/spba-bus@2000000/spi@2014000/mcp251x@1: SPI bus unit address format error, expected "0"
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix the following warnings from dtc by adding the unit name to memory
nodes:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Converted using the following command:
perl -p0777i -e 's/memory \{\n\t\treg = \<0x+([0-9a-f])/memory\@$1$\0000000 \{\n\t\treg = <0x$1/m' `find ./arch/arm/boot/dts -name "imx*"`
The files below were manually fixed:
-imx1-ads.dts
-imx1-apf9328.dts
-imx6q-pistachio.dts
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree changes for 4.2:
- Add device tree for i.MX7D SoC and imx7d-sdb board
- New i.MX6 board support: Armadeus Systems APF6, Gateworks GW5510,
and aristainetos2 boards
- Change LVDS to use simple-panel for nitrogen6x and sabrelite boards
- Add Wifi/Bluetooth devices support for cubox-i board
- Remove unused regulators and correct OTG roles setting for
imx6sl-warp board
- Add I2C support for imx23-olinuxino board
- Move imx6qdl HDMI device to a better place
- Add power-domain for imx6qdl CODA device
* tag 'imx-dt-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (24 commits)
ARM: dts: imx6dl: add imx6dl gpt specific compatible string
ARM: dts: imx6: add DT for aristainetos2 board
ARM: dts: cubox-i/hummingboard: Fix the license text
ARM: dts: sabrelite: use simple-panel instead of display-timings for LVDS0
ARM: dts: nitrogen6x: use simple-panel instead of display-timings for LVDS0
ARM: dts: add imx7d-sdb support
ARM: dts: add imx7d soc dtsi file
ARM: dts: Armadeus Systems APF6 family support (i.MX6)
ARM: dts: vf610: Nomenclature fixup for PTC12 pin used in RMII mode.
ARM: dts: cubox-i: add support for Broadcom Wifi/Bluetooth devices
Document: dt: binding: imx: update document for imx7d support
ARM: dts: imx6qdl: Add power-domain phandle to CODA device node
ARM: dts: Gateworks GW5510 support (i.MX6)
ARM: dts: imx6sl-warp: Fix OTG roles
ARM: dts: imx6sl-warp: Remove USB regulators
ARM: dts: imx6sl-warp: Remove unused regulator
ARM: dts: add pinfunc include file to support imx7d
ARM: mxs: fix in tree users of ssd1306
ARM: dts: imx6qdl-hummingboard: Add PCIe support
ARM: dts: imx23-olinuxino: Add i2c support
...
|
|
The imx23-olinuxino board has an i2c interface exposed on UEXT connector.
This patch enables i2c and selects the pin group used on UEXT connector.
Tested with MOD-LCD1x9 from Olimex.
This patch is based on work by Fadil Berisha with his permission. However
all bugs are mine.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The dr_mode of usb0 on imx233-olinuxino is left to default "otg".
Since the green LED (GPIO2_1) on imx233-olinuxino is connected to the
same pin as USB_OTG_ID it's possible to disable USB host by LED toggling:
echo 0 > /sys/class/leds/green/brightness
[ 1068.890000] ci_hdrc ci_hdrc.0: remove, state 1
[ 1068.890000] usb usb1: USB disconnect, device number 1
[ 1068.920000] usb 1-1: USB disconnect, device number 2
[ 1068.920000] usb 1-1.1: USB disconnect, device number 3
[ 1069.070000] usb 1-1.2: USB disconnect, device number 4
[ 1069.450000] ci_hdrc ci_hdrc.0: USB bus 1 deregistered
[ 1074.460000] ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11
This patch fixes the issue by setting dr_mode to "host" in the dts file.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Peter Chen <peter.chen@freescale.com>
Fixes: b49312948285 ("ARM: dts: imx23-olinuxino: Add USB host support")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
On imx23-olinuxino the LED turns on when level logic high is aplied to
GPIO2_1.
Fix the gpios property accordingly.
Fixes: b34aa1850244 ("ARM: dts: imx23-olinuxino: Remove unneeded "default-on"")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The device tree specification recommends that generic name should be
used for nodes. So instead of naming those fixed regulator nodes
arbitrarily, let's use the generic name 'regulator@num' for those nodes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Convert mx23/mx28 dts files to use the padconfig defintions from
mxs-pinfunc.h.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Convert mx23/mx28 dts filed to use the pinctrl header files.
NOTE: During automatic conversion of these files to use the pinconfig
definitions an inconsistency has been found in:
arch/arm/boot/dts/imx28-apx4devkit.dts
According to the comment the function for pad SSP2_SS0 should have
been MX28_PAD_SSP2_SS0__GPIO_2_19, while the given value 0x2131
represents: MX28_PAD_SSP2_SS0__AUART3_TX
I used the later (though probably wrong) definition because that's
what is actually being used in the DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The i.MX23 has a internal Low Resolution ADC; this enables the support
for this device.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The imx23-olinuxino sdcard doesn't have card detect.
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
On the imx23-olinuxino board GPIO2_1 is connected to the LED and GPIO0_17
is the USB PHY reset.
So make the IOMUX assignment properly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
imx23-olinuxino board has spi pins exposed on external connector.
This patch add spi support.
Signed-off-by: Fadil Berisha <f.koliqi@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Since commit 8fe4554f (leds: leds-gpio: adopt pinctrl support) gpio-led driver
has pinctrl support, so setup the gpio led pin via pinctrl and avoid the
following warning:
leds-gpio leds.5: pins are not configured from the driver
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The initial state of the gpio led can be set directly in "gpios" node.
Hence, linux,default-trigger can be removed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add USB host support.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Olinuxino has a LED connected to MX23_PAD_SSP1_DETECT__GPIO_2_1 pin.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add AUART0 support.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
mx23-olinuxino is a low cost board designed by Olimex.
It has the following features:
- Freescale iMX233 ARM926J processor at 454MHz
-64 MB RAM
-SD-card connector
-TV PAL/NTSC video output
-2 USB High Speed Hosts
-Ethernet 100 Mbit
-Stereo Audio Input
-Stereo Headphones Audio Output
More information at:
http://www.olimex.com/dev/imx233-olinuxino-maxi.html
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|