| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The node names should be generic and SPI NOR dtschema expects "flash".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220407143223.295344-1-krzysztof.kozlowski@linaro.org
|
|
The memory node requires a unit-address, add it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20200831171129.3886857-7-alexandre.belloni@bootlin.com
|
|
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations http www opensource
org licenses gpl license html http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.383790741@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As TCB2 doesn't have any output pins, use it for timers
Cc: Marek Vasut <marex@denx.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
According to the binding documentation and the source code the atmel-gpio
controller takes IRQ_TYPE_* as its flags values, not GPIO_ACTIVE_*.
This patch uses the right variable type which yields the same result
when compiled. Note that this might be wrong and actually
IRQ_TYPE_LEVEL_LOW is intended by the dt author.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The board is now manufactured by Aries Embedded GmbH, update compat string.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
vcc_3v3_reg and vcc_mmc1_reg are fixed regulators and don't need a
reg property. Remove their unit-address.
Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixedregulator@1 has a unit name, but no reg property
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The Denx MA5D4 dts doesn't properly define the slow_xtal and main_xtal
frequencies, the PMC then has to fallback to using the RC oscillators whose
precision is not really good.
As both crystals are populated, define their frequencies, see p17 of
http://www.denx-cs.de/sites/all/files/MA5D4.HWM_.002.pdf
Also, remove the obsolete main_clock definition.
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add support for the DENX MA5D4 SoM and MA5D4EVK board. The system
consists of a SoM with eMMC, SPI NOR for booting, 2x SPI CAN chip
and an EVK with microSD slot, 2x UART, 2x CAN port, 3x USB port,
LEDs and expansion headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
