Age | Commit message (Collapse) | Author | Files | Lines |
|
The board has a microchip 24aa025e48 eeprom, which is a 2 Kbits memory,
so it's compatible with at24c02 not at24c32.
Also the size property is wrong, it's not 128 bytes, but 256 bytes.
Thus removing and leaving it to the default (256).
Fixes: 1e5f532c27371 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220607090455.80433-1-eugen.hristev@microchip.com
|
|
This regulator is powering the vddcore pins from MPU.
Its real value on the board and in the MPU datasheet is 1.15V.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220302160235.28336-1-nicolas.ferre@microchip.com
|
|
The wrong property "atmel,shdwc-debouncer" was used to specify the
debounce delay for the shutdown controler. Replace it with the
documented and implemented property "debounce-delay-us", as mentioned
in v4 driver submission. See:
https://lore.kernel.org/r/1458134390-23847-3-git-send-email-nicolas.ferre@atmel.com/
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reported-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20210730172729.28093-1-nicolas.ferre@microchip.com/
|
|
Add pinctrl-names and pinctrl-0 properties on controllers that claims to
use pins to avoid failures due to
commit 2ab73c6d8323 ("gpio: Support GPIO controllers without pin-ranges")
and also to avoid using pins that may be claimed my other IPs.
Fixes: b7c2b6157079 ("ARM: at91: add Atmel's SAMA5D3 Xplained board")
Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210727074006.1609989-1-claudiu.beznea@microchip.com
Cc: <stable@vger.kernel.org> # v5.7+
|
|
Pull ARM devicetree updates from Arnd Bergmann:
"There are six new SoCs added this time.
Apple M1 and Nuvoton WPCM450 have separate branches because they are
new SoC families that require changes outside of device tree files.
The other four are variations of already supported chips and get
merged through this branch:
- STMicroelectronics STM32H750 is one of many variants of STM32
microcontrollers based on the Cortex-M7 core.
This is particularly notable since we rarely add support for new
MMU-less chips these days. In this case, the board that gets added
along with the platform is not a SoC reference platform but the
"Art Pi" (https://art-pi.gitee.io/website/) machine that was
originally design for the RT-Thread RTOS.
- NXP i.MX8QuadMax is a variant of the growing i.MX8
embedded/industrial SoC family, using two Cortex-A72 and four
Cortex-A53 cores.
It gets added along with its reference board, the "NXP i.MX8QuadMax
Multisensory Enablement Kit".
- Qualcomm SC7280 is a Laptop SoC following the SC7180 (Snapdragon
7c) that is used in some Chromebooks and Windows laptops.
Only a reference board is added for the moment.
- TI AM64x Sita4ra is a new version of the K3 SoC family for
industrial control, motor control, remote IO, IoT gateway etc.,
similar to the older AM65x family.
Two reference machines are added alongside.
Among the newly added machines, there is a very clear skew towards
64-bit machines now, with 12 32-bit machines compared to 23 64-bit
machines. The full list sorted by SoC is:
- ASpeed AST2500 BMC: ASRock E3C246D4I Xeon server board
- Allwinner A10: Topwise A721 Tablet
- Amlogic GXL: MeCool KII TV box
- Amlogic GXM: Mecool KIII, Minix Neo U9-H TV boxes
- Broadcom BCM4908: TP-Link Archer C2300 V1 router
- MStar SSD202D: M5Stack UnitV2 camera
- Marvell Armada 38x: ATL-x530 ethernet switch
- Mediatek MT8183 Chromebooks: Lenovo 10e, Acer Spin 311, Asus Flip
CM3, Asus Detachable CM3
- Mediatek MT8516/MT8183: OLogic Pumpkin Board
- NXP i.MX7: reMarkable Tablet
- NXP i.MX8M: Kontron pitx-imx8m, Engicam i.Core MX8M Mini
- Nuvoton NPCM730: Quanta GBS BMC
- Qualcomm X55: Telit FN980 TLB SoM, Thundercomm TurboX T55 SoM
- Qualcomm MSM8998: OnePlus 5/5T phones
- Qualcomm SM8350: Snapdragon 888 Mobile Hardware Development Kit
- Rockchip RK3399: NanoPi R4S board
- STM32MP1: Engicam MicroGEA STM32MP1 MicroDev 2.0 and SOM, EDIMM2.2
Starter Kit, Carrier, SOM
- TI AM65: Siemens SIMATIC IOT2050 gateway
There is notable work going into extending already supported machines
and SoCs:
- ASpeed AST2500
- Allwinner A23, A83t, A31, A64, H6
- Amlogic G12B
- Broadcom BCM4908
- Marvell Armada 7K/8K/CN91xx
- Mediatek MT6589, MT7622, MT8173, MT8183, MT8195
- NXP i.MX8Q, i.MX8MM, i.MX8MP
- Qualcomm MSM8916, SC7180, SDM845, SDX55, SM8350
- Renesas R-Car M3, V3U
- Rockchip RK3328, RK3399
- STEricsson U8500
- STMicroelectronics STM32MP141
- Samsung Exynos 4412
- TI K3-AM65, K3-J7200
- TI OMAP3
Among the treewide cleanups and bug fixes, two parts stand out:
- There are a number of cleanups for issues pointed out by 'make
dtbs_check' this time, and I expect more to come in the future as
we increasingly check for regressions.
- After a change to the MMC subsystem that can lead to unpredictable
device numbers, several platforms add 'aliases' properties for
these to give each MMC controller a fixed number"
* tag 'arm-dt-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (516 commits)
dt-bindings: mali-bifrost: add dma-coherent
arm64: dts: amlogic: misc DT schema fixups
arm64: dts: qcom: sc7180: Update iommu property for simultaneous playback
arm64: dts: qcom: sc7180: pompom: Add "dmic_clk_en" + sound model
arm64: dts: qcom: sc7180: coachz: Add "dmic_clk_en"
ARM: dts: mstar: Add a dts for M5Stack UnitV2
dt-bindings: arm: mstar: Add compatible for M5Stack UnitV2
dt-bindings: vendor-prefixes: Add vendor prefix for M5Stack
arm64: dts: mt8183: fix dtbs_check warning
arm64: dts: mt8183-pumpkin: fix dtbs_check warning
ARM: dts: aspeed: tiogapass: add hotplug controller
ARM: dts: aspeed: amd-ethanolx: Enable all used I2C busses
ARM: dts: aspeed: Rainier: Update to pass 2 hardware
ARM: dts: aspeed: Rainier 1S4U: Fix fan nodes
ARM: dts: aspeed: Rainier: Fix humidity sensor bus address
ARM: dts: aspeed: Rainier: Fix PCA9552 on bus 8
ARM: dts: qcom: sdx55: add IPA information
ARM: dts: qcom: sdx55: Add basic devicetree support for Thundercomm T55
dt-bindings: arm: qcom: Add binding for Thundercomm T55 kit
ARM: dts: qcom: sdx55: Add basic devicetree support for Telit FN980 TLB
...
|
|
Having a button code and not a key code causes issues with libinput.
udev won't set ID_INPUT_KEY. If it is forced, then it causes a bug
within libinput.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210402130227.21478-1-nicolas.ferre@microchip.com
|
|
Fix the whole mux-mask table according to datasheet for the sam9x60
product. Too much functions for pins were disabled leading to
misunderstandings when enabling more peripherals or taking this table
as an example for another board.
Take advantage of this fix to move the mux-mask in the SoC file where it
belongs and use lower case letters for hex numbers like everywhere in
the file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Cc: <stable@vger.kernel.org> # 5.6+
Cc: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210310152006.15018-1-nicolas.ferre@microchip.com
|
|
According to the datasheet PA7 can be set to either function A, B or
C (see table 6-2 of DS60001579D). The previous value would permit just
configuring with function C.
Signed-off-by: Federico Pellegrin <fede@evolware.org>
Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Cc: <stable@vger.kernel.org> # 5.6+
Cc: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
|
|
atmel,osc-bypass property sets the bit 1 at main oscillator register.
On SAM9X60 this bit is not valid according to datasheet (chapter
28.16.9 PMC Clock Generator Main Oscillator Register).
Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Marco Cardellini <marco.cardellini@microchip.com>
Link: https://lore.kernel.org/r/1606903025-14197-2-git-send-email-claudiu.beznea@microchip.com
|
|
The pincontrol node is needed for USB Host since Linux v5.7-rc1. Without
it the driver probes but VBus is not powered because of wrong pincontrol
configuration.
Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201118120019.1257580-2-cristian.birsan@microchip.com
|
|
Enable usb device for sam9x60ek board.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Add RTT. Allong with it enable GBPR as it is requested by RTT.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1591779936-18577-4-git-send-email-claudiu.beznea@microchip.com
|
|
The L1 and L3 lines drive NMOS transistors that are OFF with a low level.
On the SAM9X60 EK board, if the pins corresponding to L1 and L3
have pull-ups enabled, there is an extra 2 x 30uA power consumption.
Use pull-downs for these 2 lines to remove the unnecessary power
consumption.
Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200615095525.43414-2-codrin.ciubotariu@microchip.com
|
|
sdmmc1 is not populated by default on sam9x60ek, but there are cases
where it is populated with wilc3000. Add the node, but keep it disabled.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200403061222.1277147-4-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Both the QSPI controller and the sst26vf064b flash support
quad mode, enable it.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200403061222.1277147-1-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Enable node for watchdog timer
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/1581408369-14469-2-git-send-email-eugen.hristev@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add device tree files for SAM9X60 SoC and SAM9X60-EK board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/1579085987-13976-6-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|