| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The PRUSSs on AM57xx SoCs contain an MDIO controller that can
be used to control external PHYs associated with the Industrial
Ethernet peripherals within each PRUSS. The MDIO module used
within the PRU-ICSS is an instance of the MDIO Controller used
in TI Davinci SoCs. The same bus frequency of 1 MHz is chosen as
the regular MDIO node.
The nodes are added in the common am57-pruss.dtsi file and enabled
by default, but are disabled in all the existing AM57xx board dts
files. These nodes need pinctrl lines, and so should be enabled
only on boards where they are actually wired and pinned out for
PRUSS Ethernet. Any new board dts file should disable these if
they are not sure.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Switch all TI AM5728 BeagleBoard-X15 boards to use new cpsw switch driver.
Those boards have 2 Ext. port wired and configured in dual_mac mode by
default. Hence, dual_mac mode has been preserved the same way between
legacy and new driver it's safe to switch drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull ARM devicetree updates from Arnd Bergmann:
"This is the set of device tree changes, mostly covering new hardware
support, with 577 patches touching a little over 500 files.
There are five new Arm SoCs supported in this release, all of them for
existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in both NAS
devices and Android Set-top-box designs, along with the
"Horseradish", "Lion Skin" and "Mjolnir" reference platforms; the
Mele X1000 and Xnano X5 set-top-boxes and the Banana Pi BPi-M4
single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC and
the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the Odroid-GO
Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2" and YADRO
OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform" reference
board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board computer
and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in
existing SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone"
* tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (564 commits)
ARM: dts: keystone: Rename "msmram" node to "sram"
arm: dts: mt2712: add uart APDMA to device tree
arm64: dts: mt8183: add mmc node
arm64: dts: mt2712: add ethernet device node
arm64: tegra: Make the RTC a wakeup source on Jetson Nano and TX1
ARM: dts: mmp3: Add the fifth SD HCI
ARM: dts: berlin*: Fix up the SDHCI node names
ARM: dts: mmp3: Fix USB & USB PHY node names
ARM: dts: mmp3: Fix L2 cache controller node name
ARM: dts: mmp*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa910: Fix the gpio interrupt cell number
ARM: dts: pxa3xx: Fix up encoding of the /gpio interrupts property
ARM: dts: pxa168: Fix the gpio interrupt cell number
ARM: dts: pxa168: Add missing address/size cells to i2c nodes
ARM: dts: dove: Fix interrupt controller node name
ARM: dts: kirkwood: Fix interrupt controller node name
arm64: dts: Add SC9863A emmc and sd card nodes
arm64: dts: Add SC9863A clock nodes
arm64: dts: mt6358: add PMIC MT6358 related nodes
...
|
|
Since commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on boards:
am571x-idk
am572x-idk
am574x-idk
am57xx-beagle-x15
All above boards have phy-mode = "rgmii" and this is worked before because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay. After above commit, the
KSZ9031 PHY starts handling phy mode properly and disables RX delay, as
result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Fixes: bcf3440c6dd7 ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices on all the AM57xx BeagleBoard-X15 boards. These nodes
are assigned to the respective rproc device nodes, and all the IPU and
DSP remote processors are enabled for all these boards.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA7 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The System Mailboxes 5 and 6 and their corresponding child sub-mailbox
(IPC 3.x) nodes are enabled in each of the DRA7xx and AM57xx board
dts files individually at present. These mailboxes enable the Remote
Processor Messaging (RPMsg) communication stack between the MPU host
processor and each of the IPU1, IPU2, DSP1 and DSP2 remote processors.
Move these nodes into two common dtsi files - dra7-ipu-dsp-common and
dra74-ipu-dsp-common files, which are then included in various board
dts files. These files can be used to add all the common configuration
properties (except memory data) required by remote processor nodes.
The memory pools and the remote processor nodes themselves are to be
enabled in the actual board dts files. The first file is to used by
platforms using DRA72x/DRA71x/AM571x/AM570x SoCs, and the second file
is to be used by platforms using DRA74x/DRA76x/AM572x/AM574x SoCs.
The second file includes the first file and contains additional data
only applicable for DSP2 remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On am57xx-beagle-x15, 5V0 is connected to P16, P17, P18 and P19
connectors. On am57xx-evm, 5V0 regulator is used to get 3V6 regulator
which is connected to the COMQ port. Model 5V0 regulator here in order
for it to be used in am57xx-evm to model 3V6 regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
PERST# line in the PCIE connector is driven by the host mode and not
EP mode. The gpios property here is used for driving the PERST# line.
Remove gpios property from all endpoint device tree nodes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
The ti,no-idle-on-init and ti,no-reset-on-init flags need to be at
the interconnect target module level for the modules that have it
defined. Otherwise we get the following warnings:
dts flag should be at module level for ti,no-idle-on-init
dts flag should be at module level for ti,no-reset-on-init
Reviewed-by: Suman Anna <s-anna@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
If UHS speed modes are enabled, a compatible SD card switches down to
1.8V during enumeration. If after this a software reboot/crash takes
place and on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the
card). Because the beaglebone X15 (rev A,B and C), am57xx-idks and
am57xx-evms don't have this capability, disable voltage switching for
these boards.
The major effect of this is that the maximum supported speed
mode is now high speed(50 MHz) down from SDR104(200 MHz).
commit 88a748419b84 ("ARM: dts: am57xx-idk: Remove support for voltage
switching for SD card") did this only for idk boards. Do it for all
affected boards.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
AM5 and DRA7 SoC families have different set of modules
in them so the SoC sepecific dtsi files need to be separated.
e.g. Some of the major differences between AM576 and DRA76
DRA76x AM576x
USB3 x
USB4 x
ATL x
VCP x
MLB x
ISS x
PRU-ICSS1 x
PRU-ICSS2 x
This patch only deals with disabling USB3, USB4 and ATL for
AM57 variants.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Convert DRA7xx to use the new clockdomain based layout. Previously the
clkctrl split was based on CM isntance boundaries. The new layout
helps with introducing the interconnect driver instances.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use sdhci-omap programming model based on the generic sdhci
library for programming the eMMC/SD/SDIO controller.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add "vqmmc-supply" property for mmc2 to indicate the supply connected
to the IO lines.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Second set of device tree changes for omaps for v4.16 merge window
This branch mostly configures more hardware support:
- Clean-up dts files to remove leading 0x and 0s from binding notation
to remove more dtc compiler warnings
- A series of am437x updates for backlight, to fix inverted pad
pull macro, and to configure power management related OPPs
- Configure n950 and droid 4 command mode LCD panels
- Updates to pandora and gta04 LCD panels
- Add support for am574x-idk
- A series of changes to configure more dra7 related PCIe features
- A series of fixes for am335x-boneblue for WLAN, UARTs and CAN
configuration
- A series of changes to configure dra7 OPPs and VDD supplies
* tag 'omap-for-v4.16/dt-pt2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (29 commits)
Revert "ARM: dts: dra7: Add properties to enable PCIe x2 lane mode"
ARM: dts: am572x-idk: Add cpu0 vdd supply
ARM: dts: am571x-idk: Add cpu0 vdd supply
ARM: dts: dra72-evm-tps65917: Add cpu0 vdd supply
ARM: dts: dra7-evm: Add cpu0 vdd supply
ARM: dts: am57xx-beagle-x15-common: Add cpu0 vdd supply
ARM: dts: dra7: Enable 1.5 GHz operation for the CPU
ARM: dts: dra7: Add MPU OPP supply node
ARM: dts: dra7: Add vbb-supply to cpu and additional voltages
ARM: dts: am335x-boneblue: enable can
ARM: dts: am335x-boneblue: enable usarts
ARM: dts: am335x-boneblue: fix wl1835 IRQ pin
ARM: dts: dra7: Remove deprecated PCI compatible string
ARM: dts: dra76-evm: Enable x2 PCIe lanes
ARM: dts: DRA72x: Use PCIe compatible specific to dra72
ARM: dts: DRA74x: Use PCIe compatible specific to dra74
ARM: dts: dra7: Add properties to enable PCIe x2 lane mode
ARM: dts: am57xx: Add support for am574x-idk
ARM: dts: am43x-epos-evm: Hook dcdc2 as the cpu0-supply
ARM: dts: am437x-idk-evm: Disable OPP50 for MPU
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add vdd-supply as smps12_reg for cpu0.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add clkctrl nodes for DRA7 SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am57xx-beagle-x15/am57xx-beagle-x15-revb1.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add pcie1 dt node in order for the controller to operate in
endpoint mode. However since none of the dra7 based boards have
slots configured to operate in endpoint mode, keep EP mode
disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
10/100 Mbps"
According to errata i880 description the speed of Ethernet port 1 on AM572x
SoCs rev 1.1 should be limited to 10/100Mbps, because RGMII2 Switching
Characteristics are not compatible with 1000 Mbps operation [1].
The issue is fixed with Rev 2.0 silicon.
Hence, rework Beagle-X15 and Begale-X15-revb1 to use phy-handle instead of
phy_id and apply corresponding limitation to the Ethernet Phy 1.
[1] http://www.ti.com/lit/er/sprz429j/sprz429j.pdf
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The PMICs have POWERHOLD set by default which prevents PMIC shutdown
even on DEV_CTRL On bit set to 0 as the Powerhold has higher priority.
So to enable pmic power off this property lets one over ride the default
value and enable pmic power off.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit d20f997b4d1f ("ARM: dts: am57xx-beagle-x15: Remove pinmux
configurations for erratum i869") fat fingered a change in which
basically replaced mmc2_pinctrl_default with mmc1_pinctrl_default. And
kernel dutifully reports conflict of usage.
[...]
pinctrl-single 4a003400.pinmux: pin 4a00376c.0 already requested by
4809c000.mmc; cannot claim for 480b4000.mmc
pinctrl-single 4a003400.pinmux: pin-219 (480b4000.mmc) status -22
pinctrl-single 4a003400.pinmux: could not request pin 219 (4a00376c.0)
from group mmc1_pins_default on device pinctrl-single
omap_hsmmc 480b4000.mmc: Error applying setting, reverse things back
omap_hsmmc 480b4000.mmc: could not initialize pin control state
[...]
But, thanks to the fact that we were in fact setting all the muxes in
U-Boot, all the MMC devices were still properly detected.
Fix the typo.
Fixes: d20f997b4d1f ("ARM: dts: am57xx-beagle-x15: Remove pinmux
configurations for erratum i869")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: removed timestamps and wrapped description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Latest update to the BeagleBoard-X15 platform (revision B1)[1] updates
for allowing UHS SD cards to function with the split of supply to SD
card from a dedicated LDO.
As a result of this, AM57xx BeagleBoard-X15 now uses gpio2_30 instead
of gpio6_28 for HDMI because HDMI_LS_OE should now be switched from
GPIO6_28(Y9) to GPIO2_30 (AG8) to avoid a 1.8V GPIO toggling a 3.3V
SoC input when the SD card is in UHS 1.8V mode.
NOTE: For UHS mode to function, we need full fledged IODelay support
in kernel to be functional. IODelay support is yet to be added.
Further, It does not make much sense to spin off a new board
compatible flag since there is no real functional benefit for the
same.
Note: Even though production version is supposed to be B1, there is
over ~200 boards of previous version (A2)[2] out there which continue
to get supported with the existing dts file (to maintain compatibility
with existing bootloaders for A2) and the production board is now
supported as revb1.
[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BEAGLEBOARD_X15_REV_B1.pdf
[2] http://marc.info/?l=linux-arm-kernel&m=147273929820708&w=2
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
