Age | Commit message (Collapse) | Author | Files | Lines |
|
helpers
get rid of set_fs() in csum_partial_copy_nocheck(), while we are at it -
just take the part of csum_and_copy_from_user() sans the access_ok() check
into a helper function and have csum_partial_copy_nocheck() call that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
All callers of these primitives will
* discard anything we might've copied in case of error
* ignore the csum value in case of error
* always pass 0xffffffff as the initial sum, so the
resulting csum value (in case of success, that is) will never be 0.
That suggest the following calling conventions:
* don't pass err_ptr - just return 0 on error.
* don't bother with zeroing destination, etc. in case of error
* don't pass the initial sum - just use 0xffffffff.
This commit does the minimal conversion in the instances of csum_and_copy_...();
the changes of actual asm code behind them are done later in the series.
Note that this asm code is often shared with csum_partial_copy_nocheck();
the difference is that csum_partial_copy_nocheck() passes 0 for initial
sum while csum_and_copy_..._user() pass 0xffffffff. Fortunately, we are
free to pass 0xffffffff in all cases and subsequent patches will use that
freedom without any special comments.
A part that could be split off: parisc and uml/i386 claimed to have
csum_and_copy_to_user() instances of their own, but those were identical
to the generic one, so we simply drop them. Not sure if it's worth
a separate commit...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
It's always 0. Note that we theoretically could use ~0U as well -
result will be the same modulo 0xffff, _if_ the damn thing did the
right thing for any value of initial sum; later we'll make use of
that when convenient.
However, unlike csum_and_copy_..._user(), there are instances that
did not work for arbitrary initial sums; c6x is one such.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
It's already doing the right thing - it does access_ok() and the wrapper
in net/checksum.h is pointless here. Just rename it and be done with that...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The patch 3ddc5b46a8e90f3c9251338b60191d0a804b0d92 breaks networking on
alpha (there is a follow-up fix 5cfe8f1ba5eebe6f4b6e5858cdb1a5be4f3272a6,
but networking is still broken even with the second patch).
The patch 3ddc5b46a8e90f3c9251338b60191d0a804b0d92 makes
csum_partial_copy_from_user check the pointer with access_ok. However,
csum_partial_copy_from_user is called also from csum_partial_copy_nocheck
and csum_partial_copy_nocheck is called on kernel pointers and it is
supposed not to check pointer validity.
This bug results in ssh session hangs if the system is loaded and bulk
data are printed to ssh terminal.
This patch fixes csum_partial_copy_nocheck to call set_fs(KERNEL_DS), so
that access_ok in csum_partial_copy_from_user accepts kernel-space
addresses.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
|
|
Introduced by 3ddc5b46a8e90f3c92 ("kernel-wide: fix missing validations
on __get/__put/__copy_to/__copy_from_user()").
Also fix some other places which could be problematic in a similar way,
although they hadn't been proved so, as far as I can tell.
Cc: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Matt Turner <mattst88@gmail.com>
|
|
I found the following pattern that leads in to interesting findings:
grep -r "ret.*|=.*__put_user" *
grep -r "ret.*|=.*__get_user" *
grep -r "ret.*|=.*__copy" *
The __put_user() calls in compat_ioctl.c, ptrace compat, signal compat,
since those appear in compat code, we could probably expect the kernel
addresses not to be reachable in the lower 32-bit range, so I think they
might not be exploitable.
For the "__get_user" cases, I don't think those are exploitable: the worse
that can happen is that the kernel will copy kernel memory into in-kernel
buffers, and will fail immediately afterward.
The alpha csum_partial_copy_from_user() seems to be missing the
access_ok() check entirely. The fix is inspired from x86. This could
lead to information leak on alpha. I also noticed that many architectures
map csum_partial_copy_from_user() to csum_partial_copy_generic(), but I
wonder if the latter is performing the access checks on every
architectures.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Spelling fixes in arch/alpha/.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
* sanitize prototypes and annotate
* kill useless access_ok() in csum_partial_copy_from_user() (the only
caller checks it already).
* do_csum_partial_copy_from_user() is not needed now
* replace htons(len) with len << 8 - they are the same wrt checksums
on little-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|