Age | Commit message (Collapse) | Author | Files | Lines |
|
Document RDA Micro RDA8810PL SoC timer.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The BCM4330 is a 802.11 a/b/g/n WiFi + Bluetooth 4.0 chip from Broadcom.
It is found in the Ampak AP6330 WiFi+BT module. The partiular one I have
identifies as BCM4330B1 for Bluetooth and BCM4330/4 for WiFi.
It is unclear if the AP6330 module uses this revision of the BCM4330, or
if there are multiple revisions. The module does not have revision
markings. This patch elects to use just BCM4330 for the compatible
string.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The BCM20702A1 is a Bluetooth 4.0 chip from Broadcom. It is found in the
Ampak AP6210 WiFi+BT module, identified from the read verbose config info
command response. However the Bluetooth firmware provided by vendors uses
the name BCM20710. This patch elects to use the chip ID returned by the
chip for the compatible string.
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Broadcom Bluetooth chips have two power inputs, VBAT and VDDIO.
The former provides overall power for the chip, while the latter powers
the I/O pins and buffers.
This patch adds properties for the two so we can describe the power
supply relationships.
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Broadcom Bluetooth controllers can take up to two external clocks:
an external frequency reference, substituting the main crystal, and a
LPO clock at 32.768 kHz substituting the internal LPO clock.
In particular, the external LPO clock must be used when the controller
does not have NVRAM connected, and the main reference frequency is not
the default 20 MHz. This is described in detail in the datasheet.
The original "extclk" clock name is ambiguous as to which of these it
refers to, and some designs might even require both.
This patch deprecates the existing name, and adds "txco" and "lpo".
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add QCOM cpufreq firmware device bindings for Qualcomm Technology Inc's
SoCs. This is required for managing the cpu frequency transitions which are
controlled by the hardware engine.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Document SoC specific bindings for RZ/G2M (r8a774a1) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Document SoC specific compatible strings for r8a77470. No driver change
is needed as the fallback strings will activate the right code.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Document SoC specific bindings for R-Car M3-W (r8a7796) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Core changes:
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
|
|
NAND core changes:
- kernel-doc miscellaneous fixes.
- Third batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (ams-delta, marvell, fsmc, denali, tegra, vf610):
* Stopping to pass mtd_info objects to internal functions
* Reorganizing code to avoid forward declarations
* Dropping useless test in nand_legacy_set_defaults()
* Moving nand_exec_op() to internal.h
* Adding nand_[de]select_target() helpers
* Passing the CS line to be selected in struct nand_operation
* Making ->select_chip() optional when ->exec_op() is implemented
* Deprecating the ->select_chip() hook
* Moving the ->exec_op() method to nand_controller_ops
* Moving ->setup_data_interface() to nand_controller_ops
* Deprecating the dummy_controller field
* Fixing JEDEC detection
* Providing a helper for polling GPIO R/B pin
Raw NAND chip drivers changes:
- Macronix:
* Flagging 1.8V AC chips with a broken GET_FEATURES(TIMINGS)
Raw NAND controllers drivers changes:
- Ams-delta:
* Fixing the error path
* SPDX tag added
* May be compiled with COMPILE_TEST=y
* Conversion to ->exec_op() interface
* Dropping .IOADDR_R/W use
* Use GPIO API for data I/O
- Denali:
* Removing denali_reset_banks()
* Removing ->dev_ready() hook
* Including <linux/bits.h> instead of <linux/bitops.h>
* Changes to comply with the above fixes/cleanup done in the core.
- FSMC:
* Adding an SPDX tag to replace the license text
* Making conversion from chip to fsmc consistent
* Fixing unchecked return value in fsmc_read_page_hwecc
* Changes to comply with the above fixes/cleanup done in the core.
- Marvell:
* Preventing timeouts on a loaded machine (fix)
* Changes to comply with the above fixes/cleanup done in the core.
- OMAP2:
* Pass the parent of pdev to dma_request_chan() (fix)
- R852:
* Use generic DMA API
- sh_flctl:
* Converting to SPDX identifiers
- Sunxi:
* Write pageprog related opcodes to the right register: WCMD_SET (fix)
- Tegra:
* Stop implementing ->select_chip()
- VF610:
* Adding an SPDX tag to replace the license text
* Changes to comply with the above fixes/cleanup done in the core.
- Various trivial/spelling/coding style fixes.
SPI-NAND drivers changes:
- Removing the depreacated mt29f_spinand driver from staging.
- Adding support for:
* Toshiba TC58CVG2S0H
* GigaDevice GD5FxGQ4xA
* Winbond W25N01GV
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- A bunch of new irqchip drivers (RDA8810PL, Madera, imx-irqsteer)
- Updates for new (and old) platforms (i.MX8MQ, F1C100s)
- A number of SPDX cleanups
- A workaround for a very broken GICv3 implementation
- A platform-msi fix
- Various cleanups
|
|
Add hwlocks as optional property
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
This adds the DT binding for the Freescale IRQSTEER interrupt
multiplexer found in the i.MX8 familiy SoCs.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
|
|
Address comments on the documentation after Yong's original patch.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add IPU3-specific meta formats for processing parameters and
3A statistics.
V4L2_META_FMT_IPU3_PARAMS
V4L2_META_FMT_IPU3_STAT_3A
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
This patch adds the details about the IPU3 Imaging Unit driver (both CIO2
and IMGU).
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Those files are meant to be dual GPL 2.0 and GFDL without
implicit sections. However, by a wrong cut-and-paste, I ended
by applying a GPL 2+ license text to it, while still using the
GPL 2.0 SPDX tag, with would cause an ambiguity about the
licensing model.
Solve this by explicitly mentioning that the dual licensing
is between GPL 2.0 and GFDL and correcting the text.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Linux 4.20-rc7
* tag 'v4.20-rc7': (403 commits)
Linux 4.20-rc7
scripts/spdxcheck.py: always open files in binary mode
checkstack.pl: fix for aarch64
userfaultfd: check VM_MAYWRITE was set after verifying the uffd is registered
fs/iomap.c: get/put the page in iomap_page_create/release()
hugetlbfs: call VM_BUG_ON_PAGE earlier in free_huge_page()
memblock: annotate memblock_is_reserved() with __init_memblock
psi: fix reference to kernel commandline enable
arch/sh/include/asm/io.h: provide prototypes for PCI I/O mapping in asm/io.h
mm/sparse: add common helper to mark all memblocks present
mm: introduce common STRUCT_PAGE_MAX_SHIFT define
alpha: fix hang caused by the bootmem removal
XArray: Fix xa_alloc when id exceeds max
drm/vmwgfx: Protect from excessive execbuf kernel memory allocations v3
MAINTAINERS: Daniel for drm co-maintainer
drm/amdgpu: drop fclk/gfxclk ratio setting
IB/core: Fix oops in netdev_next_upper_dev_rcu()
dm thin: bump target version
drm/vmwgfx: remove redundant return ret statement
drm/i915: Flush GPU relocs harder for gen3
...
|
|
Document RZ/G2E (R8A774C0) SoC bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add explainations for some general IP counters, SACK and DSACK related
counters
Signed-off-by: yupeng <yupeng0921@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'clk-imx8qxp' and 'clk-imx8mq' into clk-next
- NXP i.MX7ULP SoC clock support
- Support for i.MX8QXP SoC clocks
- Support for NXP i.MX8MQ clock controllers
* clk-imx7ulp:
clk: imx: add imx7ulp clk driver
clk: imx: implement new clk_hw based APIs
clk: imx: make mux parent strings const
dt-bindings: clock: add imx7ulp clock binding doc
clk: imx: add imx7ulp composite clk support
clk: imx: add pfdv2 support
clk: imx: add pllv4 support
clk: fractional-divider: add CLK_FRAC_DIVIDER_ZERO_BASED flag support
clk: imx: add gatable clock divider support
* clk-imx6-fixes:
clk: imx6q: handle ENET PLL bypass
clk: imx6q: optionally get CCM inputs via standard clock handles
clk: imx6q: reset exclusive gates on init
* clk-imx-fixes:
clk: imx6q: add DCICx clocks gate
clk: imx6sl: ensure MMDC CH0 handshake is bypassed
clk: imx7d: remove UART1 clock setting
* clk-imx8qxp:
clk: imx: add imx8qxp lpcg driver
clk: imx: add lpcg clock support
clk: imx: add imx8qxp clk driver
clk: imx: add scu clock common part
clk: imx: add configuration option for mmio clks
dt-bindings: clock: add imx8qxp lpcg clock binding
dt-bindings: clock: imx8qxp: add SCU clock IDs
firmware: imx: add pm svc headfile
dt-bindings: fsl: scu: update power domain binding
firmware: imx: remove resource id enums
dt-bindings: imx: add scu resource id headfile
* clk-imx8mq:
clk: imx: Make the i.MX8MQ CCM clock driver CLK_IMX8MQ dependant
clk: imx: remove redundant initialization of ret to zero
clk: imx: Add SCCG PLL type
clk: imx: Add fractional PLL output clock
clk: imx: Add clock driver for i.MX8MQ CCM
clk: imx: Add imx composite clock
dt-bindings: Add binding for i.MX8MQ CCM
|
|
'clk-rockchip' into clk-next
* clk-renesas:
clk: renesas: rcar-gen3: Add HS400 quirk for SD clock
clk: renesas: rcar-gen3: Add documentation for SD clocks
clk: renesas: rcar-gen3: Set state when registering SD clocks
clk: renesas: r8a77995: Simplify PLL3 multiplier/divider
clk: renesas: r8a77995: Add missing CPEX clock
clk: renesas: r8a77995: Remove non-existent SSP clocks
clk: renesas: r8a77995: Remove non-existent VIN5-7 module clocks
clk: renesas: r8a77995: Correct parent clock of DU
clk: renesas: r8a77990: Correct parent clock of DU
clk: renesas: r8a77970: Add CPEX clock
clk: renesas: r8a77965: Add CPEX clock
clk: renesas: r8a7796: Add CPEX clock
clk: renesas: r8a7795: Add CPEX clock
clk: renesas: r8a774a1: Add CPEX clock
dt-bindings: clock: r8a7796: Remove CSIREF clock
dt-bindings: clock: r8a7795: Remove CSIREF clock
clk: renesas: Mark rza2_cpg_clk_register static
clk: renesas: r7s9210: Add USB clocks
clk: renesas: r8a77970: Add RPC clocks
clk: renesas: r7s9210: Add SDHI clocks
* clk-allwinner:
clk: sunxi-ng: a64: Allow parent change for VE clock
clk: sunxi-ng: a33: Set CLK_SET_RATE_PARENT for all audio module clocks
clk: sunxi-ng: a33: Use sigma-delta modulation for audio PLL
clk: sunxi-ng: h3: Allow parent change for ve clock
clk: sunxi-ng: add support for suniv F1C100s SoC
dt-bindings: clock: Add Allwinner suniv F1C100s CCU
clk: sunxi-ng: h3/h5: Fix CSI_MCLK parent
clk: sunxi-ng: r40: Force LOSC parent to RTC LOSC output
clk: sunxi-ng: sun50i: a64: Use sigma-delta modulation for audio PLL
clk: sunxi-ng: a64: Fix gate bit of DSI DPHY
clk: sunxi-ng: Enable DE2_CCU for SUN8I and SUN50I
clk: sunxi-ng: Add support for H6 DE3 clocks
dt-bindings: clock: sun8i-de2: Add H6 DE3 clock description
clk: sunxi-ng: h6: Set video PLLs limits
clk: sunxi-ng: Use u64 for calculation of NM rate
clk: sunxi-ng: Adjust MP clock parent rate when allowed
clk: sunxi-ng: sun50i: h6: Fix MMC clock mux width
clk: sunxi-ng: enable so-said LDOs for A64 SoC's pll-mipi clock
* clk-tegra:
clk: tegra: Return the exact clock rate from clk_round_rate
clk: tegra30: Use Tegra CPU powergate helper function
soc/tegra: pmc: Drop SMP dependency from CPU APIs
clk: tegra: Fix maximum audio sync clock for Tegra124/210
clk: tegra: get rid of duplicate defines
clk: tegra20: Check whether direct PLLM sourcing is turned off for EMC
clk: tegra20: Turn EMC clock gate into divider
* clk-meson: (25 commits)
clk: meson: axg-audio: use the clk input helper function
clk: meson: add clk-input helper function
clk: meson: Mark some things static
clk: meson: meson8b: add the read-only video clock trees
clk: meson: meson8b: add the fractional divider for vid_pll_dco
clk: meson: meson8b: fix the offset of vid_pll_dco's N value
clk: meson: Fix GXL HDMI PLL fractional bits width
clk: meson: meson8b: add the CPU clock post divider clocks
clk: meson: meson8b: rename cpu_div2/cpu_div3 to cpu_in_div2/cpu_in_div3
clk: meson: clk-regmap: add read-only gate ops
clk: meson: meson8b: allow changing the CPU clock tree
clk: meson: meson8b: run from the XTAL when changing the CPU frequency
clk: meson: meson8b: add support for more M/N values in sys_pll
clk: meson: meson8b: mark the CPU clock as CLK_IS_CRITICAL
clk: meson: meson8b: do not use cpu_div3 for cpu_scale_out_sel
clk: meson: clk-pll: check if the clock is already enabled
clk: meson: meson8b: fix the width of the cpu_scale_div clock
clk: meson: meson8b: fix incorrect divider mapping in cpu_scale_table
clk: meson: meson8b: use the HHI syscon if available
dt-bindings: clock: meson8b: use the registers from the HHI syscon
...
* clk-rockchip:
clk: rockchip: add clock-id to gate of ACODEC for rk3328
clk: rockchip: add clock ID of ACODEC for rk3328
clk: rockchip: fix ID of 8ch clock of I2S1 for rk3328
clk: rockchip: fix I2S1 clock gate register for rk3328
clk: rockchip: make rk3188 hclk_vio_bus critical
clk: rockchip: fix rk3188 sclk_mac_lbtest parameter ordering
clk: rockchip: fix rk3188 sclk_smc gate data
clk: rockchip: fix typo in rk3188 spdif_frac parent
|
|
- Qualcomm SDM845 audio subsystem clks
* clk-qcom-sdm845-lpass:
clk: qcom: Add lpass clock controller driver for SDM845
dt-bindings: clock: Introduce QCOM LPASS clock bindings
dt-bindings: clock: Update GCC bindings for protected-clocks
|
|
'clk-qcom-spi' and 'clk-qcom-videocc-binding' into clk-next
- Qualcomm SDM845 GPU clock controllers
- Qualcomm QCS404 RPM clk support
* clk-qcom-kconfig:
clk: qcom: Move to menuconfig and reduce lines
* clk-qcom-gpucc:
dt-bindings: clock: qcom: Fix the xo parent in gpucc example
clk: qcom: gpu_cc_gmu_clk_src has 5 parents, not 6
clk: qcom: Add a dummy enable function for GX gdsc
clk: qcom: gdsc: Don't override existing gdsc pd functions
clk: qcom: Add graphics clock controller driver for SDM845
dt-bindings: clock: Introduce QCOM Graphics clock bindings
* clk-qcom-qcs404-rpm:
clk: qcom: smd: Add support for QCS404 rpm clocks
* clk-qcom-spi:
clk: qcom: msm8916: Additional clock rates for spi
* clk-qcom-videocc-binding:
dt-bindings: clock: Require #reset-cells in sdm845-videocc
|
|
'clk-define-show-macro' and 'clk-static' into clk-next
- NXP QorIQ T1023 SoC support
- Introduce a 'protected-clocks' binding for firmware protected clks
- Shrink code some with DEFINE_SHOW_ATTRIBUTE()
* clk-qoriq-t1023:
clk: qoriq: add more chips support
* clk-protected-binding:
clk: qcom: Support 'protected-clocks' property
dt-bindings: clk: Introduce 'protected-clocks' property
* clk-define-show-macro:
clk: tegra: Change to use DEFINE_SHOW_ATTRIBUTE macro
clk: nomadik: Change to use DEFINE_SHOW_ATTRIBUTE macro
* clk-static:
clk: stm32mp1: drop pointless static qualifier in stm32_register_hw_clk()
|
|
With every new Hyper-V Enlightenment we implement we're forced to add a
KVM_CAP_HYPERV_* capability. While this approach works it is fairly
inconvenient: the majority of the enlightenments we do have corresponding
CPUID feature bit(s) and userspace has to know this anyways to be able to
expose the feature to the guest.
Add KVM_GET_SUPPORTED_HV_CPUID ioctl (backed by KVM_CAP_HYPERV_CPUID, "one
cap to rule them all!") returning all Hyper-V CPUID feature leaves.
Using the existing KVM_GET_SUPPORTED_CPUID doesn't seem to be possible:
Hyper-V CPUID feature leaves intersect with KVM's (e.g. 0x40000000,
0x40000001) and we would probably confuse userspace in case we decide to
return these twice.
KVM_CAP_HYPERV_CPUID's number is interim: we're intended to drop
KVM_CAP_HYPERV_STIMER_DIRECT and use its number instead.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This patch adds board specific bindings required for dais, In particular
for compressed dais and dai direction.
Board specific setup involves setting up some of dais as compressed dais
and also specify direction of any dai. Some of the dais might only
support capture/playback depending on the board level wiring.
These two new dt properties will allow such flexibilty at board level dts.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document RZ/G2E (R8A774C0) SoC bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document RZ/G2E (R8A774C0) SoC bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
simple-card and simple-scu-card are very similar driver,
but the former is supporting normal sound card,
the latter is supporting DPCM sound card.
We couldn't use normal sound and DPCM sound in same time by
one sound card. This patch merges both sound card into
simple-card. Now we can use both feature on same driver.
simple-card is now supporting .compatible = "simple-scu-audio-card".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
audio-graph-card and audio-graph-scu-card are very similar driver,
but the former is supporting normal sound card,
the latter is supporting DPCM sound card.
We couldn't use normal sound and DPCM sound in same sound card by
audio-graph-card.
This patch merges both feature into it on Documentation.
Now we can use both feature on same driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are two problems with KVM_GET_DIRTY_LOG. First, and less important,
it can take kvm->mmu_lock for an extended period of time. Second, its user
can actually see many false positives in some cases. The latter is due
to a benign race like this:
1. KVM_GET_DIRTY_LOG returns a set of dirty pages and write protects
them.
2. The guest modifies the pages, causing them to be marked ditry.
3. Userspace actually copies the pages.
4. KVM_GET_DIRTY_LOG returns those pages as dirty again, even though
they were not written to since (3).
This is especially a problem for large guests, where the time between
(1) and (3) can be substantial. This patch introduces a new
capability which, when enabled, makes KVM_GET_DIRTY_LOG not
write-protect the pages it returns. Instead, userspace has to
explicitly clear the dirty log bits just before using the content
of the page. The new KVM_CLEAR_DIRTY_LOG ioctl can also operate on a
64-page granularity rather than requiring to sync a full memslot;
this way, the mmu_lock is taken for small amounts of time, and
only a small amount of time will pass between write protection
of pages and the sending of their content.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The first such capability to be handled in virt/kvm/ will be manual
dirty page reprotection.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Document the interface for metadata output, including
V4L2_BUF_TYPE_META_OUTPUT buffer type and V4L2_CAP_META_OUTPUT capability
bits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Tested-by: Tian Shu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The Low-Power Clock Gate (LPCG) modules contain a local programming
model to control the clock gates for the peripherals. An LPCG module
is used to locally gate the clocks for the associated peripheral.
Note:
This level of clock gating is provided after the clocks are generated
by the SCU resources and clock controls. Thus even if the clock is
enabled by these control bits, it might still not be running based
on the base resource.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Pull XArray fixes from Matthew Wilcox:
"Two bugfixes, each with test-suite updates, two improvements to the
test-suite without associated bugs, and one patch adding a missing
API"
* tag 'xarray-4.20-rc7' of git://git.infradead.org/users/willy/linux-dax:
XArray: Fix xa_alloc when id exceeds max
XArray tests: Check iterating over multiorder entries
XArray tests: Handle larger indices more elegantly
XArray: Add xa_cmpxchg_irq and xa_cmpxchg_bh
radix tree: Don't return retry entries from lookup
|
|
Access to GICR_WAKER is restricted on msm8996 SoC in Hypervisor.
There are many devices out there with this restriction in place
and there has been no update to this firmware since last few years,
making those devices totally unusable for upstream development.
IIDR register value conflicts with other SoCs, using compatible seems
to be the only way to apply quirks required for msm8996 based SoCs.
Without this quirk many qcom SoCs (atleast 3 that I know) are
unable to boot mainline.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Now that we've added code to support pointer authentication, add some
documentation so that people can figure out if/how to use it.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Reviewed-by: Ramana Radhakrishnan <ramana.radhakrishnan@arm.com>
Cc: Andrew Jones <drjones@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ramana Radhakrishnan <ramana.radhakrishnan@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
In the past, there have been words on various lists that if LDO3 is
disabled in u-boot, but enabled in the DTS, the axp209 driver would
fail to continue/hang. Several enable/disable patches have been
issues to devicetree's in both the kernel and u-boot to address
this issue.
What really happened however, was that the AXP209 shuts down without
a notice and without setting an interrupt. This is caused when LDO3
gets overloaded, for example with large capacitors on the LDO3 output.
Normally, we would expect that AXP209 would source 200 mA as per
datasheet and set and trigger an interrupt when being overloaded.
For some reason however, this does not happen.
As a work-around, implement software-based 'regulator-soft-start'
property for AXP209 LDO3 regulator, which is used to first bring up
the LDO3 to the lowest possible voltage and then enable the LDO.
After that, we can set the requested voltage as usual.
Combining this setting with the regulator-ramp-delay allows LDO3 to
come up slowly and staggered, potentially reducing overall inrush current.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3, therefore we can use the standard 'regulator-ramp-delay'
property for those 2 regulators.
Note that the voltage ramp only works when the regulator is already
enabled. E.g. when going from say 0.7 V to 3.6 V.
When turning on the regulator, no voltage ramp is performed in hardware.
What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Added documentation for I2S IP core DT bindings.
Signed-off-by: Maruthi Srinivas Bayyavarapu <maruthi.srinivas.bayyavarapu@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch describes the compatible and the device tree
bindings necessary for the MCP16502 PMIC.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the DT binding documentation for axg's SPDIF input.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add introductions of interrupt-parent and spi-slave.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix the spelling of "transmitter".
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add compatible string for Alwinner suniv F1C100s SoC interrupt
controller which is stripped version of sun4i
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Document interrupt controller in RDA Micro RDA8810PL SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- one regression at vsp1 driver
- some last time changes for the upcoming request API logic and for
stateless codec support. As the stateless codec "cedrus" driver is at
staging, don't apply the MPEG controls as part of the main V4L2 API,
as those may not be ready for production yet.
* tag 'media/v4.20-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: Add a Kconfig option for the Request API
media: extended-controls.rst: add note to the MPEG2 state controls
media: mpeg2-ctrls.h: move MPEG2 state controls to non-public header
media: vicodec: set state resolution from raw format
media: vivid: drop v4l2_ctrl_request_complete() from start_streaming
media: vb2: don't unbind/put the object when going to state QUEUED
media: vb2: keep a reference to the request until dqbuf
media: vb2: skip request checks for VIDIOC_PREPARE_BUF
media: vb2: don't call __vb2_queue_cancel if vb2_start_streaming failed
media: cedrus: Fix a NULL vs IS_ERR() check
media: vsp1: Fix LIF buffer thresholds
|