Age | Commit message (Collapse) | Author | Files | Lines |
|
Introduces a driver for the LogiCVC display controller, a programmable
logic controller optimized for use in Xilinx Zynq-7000 SoCs and other
Xilinx FPGAs. The controller is mostly configured at logic synthesis
time so only a subset of configuration is left for the driver to
handle.
The following features are implemented and tested:
- LVDS 4-bit interface;
- RGB565 pixel formats;
- Multiple layers and hardware composition;
- Layer-wide alpha mode;
The following features are implemented but untested:
- Other RGB pixel formats;
- Layer framebuffer configuration for version 4;
- Lowest-layer used as background color;
- Per-pixel alpha mode.
The following features are not implemented:
- YUV pixel formats;
- DVI, LVDS 3-bit, ITU656 and camera link interfaces;
- External parallel input for layer;
- Color-keying;
- LUT-based alpha modes.
Additional implementation-specific notes:
- Panels are only enabled after the first page flip to avoid flashing a
white screen.
- Depth used in context of the LogiCVC driver only counts color components
to match the definition of the synthesis parameters.
Support is implemented for both version 3 and 4 of the controller.
With version 3, framebuffers are stored in a dedicated contiguous
memory area, with a base address hardcoded for each layer. This requires
using a dedicated CMA pool registered at the base address and tweaking a
few offset-related registers to try to use any buffer allocated from
the pool. This is done on a best-effort basis to have the hardware cope
with the DRM framebuffer allocation model and there is no guarantee
that each buffer allocated by GEM CMA can be used for any layer.
In particular, buffers allocated below the base address for a layer are
guaranteed not to be configurable for that layer. See the implementation of
logicvc_layer_buffer_find_setup for specifics.
Version 4 allows configuring each buffer address directly, which
guarantees that any buffer can be configured.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220520141555.1429041-2-paul.kocialkowski@bootlin.com
|
|
This reverts commit fb561bf9abde49f7e00fdbf9ed2ccf2d86cac8ee.
With
commit 27599aacbaefcbf2af7b06b0029459bbf682000d
Author: Thomas Zimmermann <tzimmermann@suse.de>
Date: Tue Jan 25 10:12:18 2022 +0100
fbdev: Hot-unplug firmware fb devices on forced removal
this should be fixed properly and we can remove this somewhat hackish
check here (e.g. this won't catch drm drivers if fbdev emulation isn't
enabled).
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Zack Rusin <zackr@vmware.com>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Zack Rusin <zackr@vmware.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ilya Trukhanov <lahvuun@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220607182338.344270-5-javierm@redhat.com
|
|
The platform devices registered by sysfb match with firmware-based DRM or
fbdev drivers, that are used to have early graphics using a framebuffer
provided by the system firmware.
DRM or fbdev drivers later are probed and remove conflicting framebuffers,
leading to these platform devices for generic drivers to be unregistered.
But the current solution has a race, since the sysfb_init() function could
be called after a DRM or fbdev driver is probed and request to unregister
the devices for drivers with conflicting framebuffes.
To prevent this, disable any future sysfb platform device registration by
calling sysfb_disable(), if a driver requests to remove the conflicting
framebuffers.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220607182338.344270-4-javierm@redhat.com
|
|
This can be used by subsystems to unregister a platform device registered
by sysfb and also to disable future platform device registration in sysfb.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220607182338.344270-3-javierm@redhat.com
|
|
This function just returned 0 on success or an errno code on error, but it
could be useful for sysfb_init() callers to have a pointer to the device.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220607182338.344270-2-javierm@redhat.com
|
|
After moving the vmalloc() call to another file, the rsp include
statement needs to be moved as well. Resolves a build warning on
parisc.
drivers/gpu/drm/mgag200/mgag200_g200.c: In function
'mgag200_g200_init_refclk':
drivers/gpu/drm/mgag200/mgag200_g200.c:120:16: error: implicit
declaration of function 'vmalloc'; did you mean 'kvmalloc'?
[-Werror=implicit-function-declaration]
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 85397f6bc4ff ("drm/mgag200: Initialize each model in separate function")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Jocelyn Falempe <jfalempe@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Link: https://lore.kernel.org/all/202206080734.ztAvDG7O-lkp@intel.com/
Link: https://patchwork.freedesktop.org/patch/msgid/20220608115122.7448-1-tzimmermann@suse.de
|
|
Since drm_prime_pages_to_sg() function return error pointers.
The drm_gem_shmem_get_sg_table() function returns error pointers too.
Using IS_ERR() to check the return value to fix this.
Fixes: 2f2aa13724d5 ("drm/virtio: move virtio_gpu_mem_entry initialization to new function")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20220602104223.54527-1-linmq006@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
If the DMA mask is not set explicitly, the following warning occurs
when the userspace tries to access the dma-buf via the CPU as
reported by syzbot here:
WARNING: CPU: 1 PID: 3595 at kernel/dma/mapping.c:188
__dma_map_sg_attrs+0x181/0x1f0 kernel/dma/mapping.c:188
Modules linked in:
CPU: 0 PID: 3595 Comm: syz-executor249 Not tainted
5.17.0-rc2-syzkaller-00316-g0457e5153e0e #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:__dma_map_sg_attrs+0x181/0x1f0 kernel/dma/mapping.c:188
Code: 00 00 00 00 00 fc ff df 48 c1 e8 03 80 3c 10 00 75 71 4c 8b 3d c0
83 b5 0d e9 db fe ff ff e8 b6 0f 13 00 0f 0b e8 af 0f 13 00 <0f> 0b 45
31 e4 e9 54 ff ff ff e8 a0 0f 13 00 49 8d 7f 50 48 b8 00
RSP: 0018:ffffc90002a07d68 EFLAGS: 00010293
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff88807e25e2c0 RSI: ffffffff81649e91 RDI: ffff88801b848408
RBP: ffff88801b848000 R08: 0000000000000002 R09: ffff88801d86c74f
R10: ffffffff81649d72 R11: 0000000000000001 R12: 0000000000000002
R13: ffff88801d86c680 R14: 0000000000000001 R15: 0000000000000000
FS: 0000555556e30300(0000) GS:ffff8880b9d00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000200000cc CR3: 000000001d74a000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
dma_map_sgtable+0x70/0xf0 kernel/dma/mapping.c:264
get_sg_table.isra.0+0xe0/0x160 drivers/dma-buf/udmabuf.c:72
begin_cpu_udmabuf+0x130/0x1d0 drivers/dma-buf/udmabuf.c:126
dma_buf_begin_cpu_access+0xfd/0x1d0 drivers/dma-buf/dma-buf.c:1164
dma_buf_ioctl+0x259/0x2b0 drivers/dma-buf/dma-buf.c:363
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:874 [inline]
__se_sys_ioctl fs/ioctl.c:860 [inline]
__x64_sys_ioctl+0x193/0x200 fs/ioctl.c:860
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f62fcf530f9
Code: 28 c3 e8 2a 14 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89
f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01
f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffe3edab9b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f62fcf530f9
RDX: 0000000020000200 RSI: 0000000040086200 RDI: 0000000000000006
RBP: 00007f62fcf170e0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f62fcf17170
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
</TASK>
v2: Dont't forget to deregister if DMA mask setup fails.
Reported-by: syzbot+10e27961f4da37c443b2@syzkaller.appspotmail.com
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20220520205235.3687336-1-vivek.kasireddy@intel.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Simplify the return expression.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: http://patchwork.freedesktop.org/patch/msgid/20220429054911.3851977-1-chi.minghao@zte.com.cn
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Smatch reports this issue
qxl_kms.c:36:5: warning: symbol 'qxl_log_level' was not declared. Should it be static?
qxl_log_level is defined qxl_kms.c but unused, so remove.
Signed-off-by: Tom Rix <trix@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20220421142054.3751507-1-trix@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Instead of relying on it getting pulled in indirectly.
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20220413161259.1854270-1-michel@daenzer.net
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
'cache_ent' could be set NULL inside virtio_gpu_cmd_get_capset()
and it will lead to a NULL dereference by a lately use of it
(i.e., ptr = cache_ent->caps_cache). Fix it with a NULL check.
Fixes: 62fb7a5e10962 ("virtio-gpu: add 3d/virgl support")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Reviewed-by: Chia-I Wu <olvaffe@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20220327050945.1614-1-xiam0nd.tong@gmail.com
[ kraxel: minor codestyle fixup ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
While working at fixing powerpc headers, I ended up with the
following error.
drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadowrom.c:48:1: error: conflicting types for 'prom_init'; have 'void *(struct nvkm_bios *, const char *)'
make[5]: *** [scripts/Makefile.build:288: drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadowrom.o] Error 1
powerpc and a few other architectures have a prom_init() global function.
One day or another it will conflict with the one in shadowrom.c
Those being static, they can easily be renamed. Do it.
While at it, also rename the ops structure as 'nvbios_prom' instead of
'nvbios_rom' in order to make it clear that it refers to the
NV_PROM device.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7e0612b61511ec8030e3b2dcbfaa7751781c8b91.1647684507.git.christophe.leroy@csgroup.eu
|
|
Add backlight property and update example to include it.
Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/BY5PR02MB70090BB5D8C7D655BEE0642FD9E09@BY5PR02MB7009.namprd02.prod.outlook.com
|
|
Add support for backlight. This panel supports backlight control
through the QCOM WLED driver in Xiaomi Poco F1 device.
Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/BY5PR02MB700935F5817128CB7C3991CDD9E09@BY5PR02MB7009.namprd02.prod.outlook.com
|
|
initmem_freed was removed in v2.1.124, and the underlying issue was
fixed for good in commit 92b004d1aa9f367c ("video/logo: prevent use of
logos after they have been freed").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/b8b9147a48e233fe32e072f2085c7b413cd92a00.1654702835.git.geert+renesas@glider.be
|
|
Since it's inception in 2012 it has been understood that the DRM GEM CMA
helpers do not depend on CMA as the backend allocator. In fact the first
bug fix to ensure the cma-helpers work correctly with an IOMMU backend
appeared in 2014. However currently the documentation for
drm_gem_cma_create() talks about "a contiguous chunk of memory" without
making clear which address space it will be a contiguous part of.
Additionally the CMA introduction is actively misleading because it only
contemplates the CMA backend.
This matters because when the device accesses the bus through an IOMMU
(and don't use the CMA backend) then the allocated memory is contiguous
only in the IOVA space. This is a significant difference compared to the
CMA backend and the behaviour can be a surprise even to someone who does
a reasonable level of code browsing (but doesn't find all the relevant
function pointers ;-) ).
Improve the kernel doc comments accordingly.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220608135821.1153346-1-daniel.thompson@linaro.org
|
|
This patch is analogous to the previous sync file export patch in that
it allows you to import a sync_file into a dma-buf. Unlike the previous
patch, however, this does add genuinely new functionality to dma-buf.
Without this, the only way to attach a sync_file to a dma-buf is to
submit a batch to your driver of choice which waits on the sync_file and
claims to write to the dma-buf. Even if said batch is a no-op, a submit
is typically way more overhead than just attaching a fence. A submit
may also imply extra synchronization with other work because it happens
on a hardware queue.
In the Vulkan world, this is useful for dealing with the out-fence from
vkQueuePresent. Current Linux window-systems (X11, Wayland, etc.) all
rely on dma-buf implicit sync. Since Vulkan is an explicit sync API, we
get a set of fences (VkSemaphores) in vkQueuePresent and have to stash
those as an exclusive (write) fence on the dma-buf. We handle it in
Mesa today with the above mentioned dummy submit trick. This ioctl
would allow us to set it directly without the dummy submit.
This may also open up possibilities for GPU drivers to move away from
implicit sync for their kernel driver uAPI and instead provide sync
files and rely on dma-buf import/export for communicating with other
implicit sync clients.
We make the explicit choice here to only allow setting RW fences which
translates to an exclusive fence on the dma_resv. There's no use for
read-only fences for communicating with other implicit sync userspace
and any such attempts are likely to be racy at best. When we got to
insert the RW fence, the actual fence we set as the new exclusive fence
is a combination of the sync_file provided by the user and all the other
fences on the dma_resv. This ensures that the newly added exclusive
fence will never signal before the old one would have and ensures that
we don't break any dma_resv contracts. We require userspace to specify
RW in the flags for symmetry with the export ioctl and in case we ever
want to support read fences in the future.
There is one downside here that's worth documenting: If two clients
writing to the same dma-buf using this API race with each other, their
actions on the dma-buf may happen in parallel or in an undefined order.
Both with and without this API, the pattern is the same: Collect all
the fences on dma-buf, submit work which depends on said fences, and
then set a new exclusive (write) fence on the dma-buf which depends on
said work. The difference is that, when it's all handled by the GPU
driver's submit ioctl, the three operations happen atomically under the
dma_resv lock. If two userspace submits race, one will happen before
the other. You aren't guaranteed which but you are guaranteed that
they're strictly ordered. If userspace manages the fences itself, then
these three operations happen separately and the two render operations
may happen genuinely in parallel or get interleaved. However, this is a
case of userspace racing with itself. As long as we ensure userspace
can't back the kernel into a corner, it should be fine.
v2 (Jason Ekstrand):
- Use a wrapper dma_fence_array of all fences including the new one
when importing an exclusive fence.
v3 (Jason Ekstrand):
- Lock around setting shared fences as well as exclusive
- Mark SIGNAL_SYNC_FILE as a read-write ioctl.
- Initialize ret to 0 in dma_buf_wait_sync_file
v4 (Jason Ekstrand):
- Use the new dma_resv_get_singleton helper
v5 (Jason Ekstrand):
- Rename the IOCTLs to import/export rather than wait/signal
- Drop the WRITE flag and always get/set the exclusive fence
v6 (Jason Ekstrand):
- Split import and export into separate patches
- New commit message
v7 (Daniel Vetter):
- Fix the uapi header to use the right struct in the ioctl
- Use a separate dma_buf_import_sync_file struct
- Add kerneldoc for dma_buf_import_sync_file
v8 (Jason Ekstrand):
- Rebase on Christian König's fence rework
v9 (Daniel Vetter):
- Fix -EINVAL checks for the flags parameter
- Add documentation about read/write fences
- Add documentation about the expected usage of import/export and
specifically call out the possible userspace race.
v10 (Simon Ser):
- Fix a typo in the docs
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Jason Ekstrand <jason.ekstrand@intel.com>
Signed-off-by: Jason Ekstrand <jason.ekstrand@collabora.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20220608152142.14495-3-jason@jlekstrand.net
|
|
Modern userspace APIs like Vulkan are built on an explicit
synchronization model. This doesn't always play nicely with the
implicit synchronization used in the kernel and assumed by X11 and
Wayland. The client -> compositor half of the synchronization isn't too
bad, at least on intel, because we can control whether or not i915
synchronizes on the buffer and whether or not it's considered written.
The harder part is the compositor -> client synchronization when we get
the buffer back from the compositor. We're required to be able to
provide the client with a VkSemaphore and VkFence representing the point
in time where the window system (compositor and/or display) finished
using the buffer. With current APIs, it's very hard to do this in such
a way that we don't get confused by the Vulkan driver's access of the
buffer. In particular, once we tell the kernel that we're rendering to
the buffer again, any CPU waits on the buffer or GPU dependencies will
wait on some of the client rendering and not just the compositor.
This new IOCTL solves this problem by allowing us to get a snapshot of
the implicit synchronization state of a given dma-buf in the form of a
sync file. It's effectively the same as a poll() or I915_GEM_WAIT only,
instead of CPU waiting directly, it encapsulates the wait operation, at
the current moment in time, in a sync_file so we can check/wait on it
later. As long as the Vulkan driver does the sync_file export from the
dma-buf before we re-introduce it for rendering, it will only contain
fences from the compositor or display. This allows to accurately turn
it into a VkFence or VkSemaphore without any over-synchronization.
By making this an ioctl on the dma-buf itself, it allows this new
functionality to be used in an entirely driver-agnostic way without
having access to a DRM fd. This makes it ideal for use in driver-generic
code in Mesa or in a client such as a compositor where the DRM fd may be
hard to reach.
v2 (Jason Ekstrand):
- Use a wrapper dma_fence_array of all fences including the new one
when importing an exclusive fence.
v3 (Jason Ekstrand):
- Lock around setting shared fences as well as exclusive
- Mark SIGNAL_SYNC_FILE as a read-write ioctl.
- Initialize ret to 0 in dma_buf_wait_sync_file
v4 (Jason Ekstrand):
- Use the new dma_resv_get_singleton helper
v5 (Jason Ekstrand):
- Rename the IOCTLs to import/export rather than wait/signal
- Drop the WRITE flag and always get/set the exclusive fence
v6 (Jason Ekstrand):
- Drop the sync_file import as it was all-around sketchy and not nearly
as useful as import.
- Re-introduce READ/WRITE flag support for export
- Rework the commit message
v7 (Jason Ekstrand):
- Require at least one sync flag
- Fix a refcounting bug: dma_resv_get_excl() doesn't take a reference
- Use _rcu helpers since we're accessing the dma_resv read-only
v8 (Jason Ekstrand):
- Return -ENOMEM if the sync_file_create fails
- Predicate support on IS_ENABLED(CONFIG_SYNC_FILE)
v9 (Jason Ekstrand):
- Add documentation for the new ioctl
v10 (Jason Ekstrand):
- Go back to dma_buf_sync_file as the ioctl struct name
v11 (Daniel Vetter):
- Go back to dma_buf_export_sync_file as the ioctl struct name
- Better kerneldoc describing what the read/write flags do
v12 (Christian König):
- Document why we chose to make it an ioctl on dma-buf
v13 (Jason Ekstrand):
- Rebase on Christian König's fence rework
v14 (Daniel Vetter & Christian König):
- Use dma_rev_usage_rw to get the properly inverted usage to pass to
dma_resv_get_singleton()
- Clean up the sync_file and fd if copy_to_user() fails
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Jason Ekstrand <jason.ekstrand@intel.com>
Signed-off-by: Jason Ekstrand <jason.ekstrand@collabora.com>
Acked-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20220608152142.14495-2-jason@jlekstrand.net
|
|
Systems with AST graphics can have multiple output; typically VGA
plus some other port. Record detected output chips in a bitmask and
initialize each output on its own.
Assume a VGA output by default and use SIL164 and DP501 if available.
For ASTDP assume that it can run in parallel with VGA.
Tested on AST2100.
v3:
* define a macro for each BIT(ast_tx_chip) (Patrik)
v2:
* make VGA/SIL164/DP501 mutually exclusive
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Fixes: a59b026419f3 ("drm/ast: Initialize encoder and connector for VGA in helper function")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220607092008.22123-2-tzimmermann@suse.de
|
|
During device remove care needs to be taken that no work is pending
before it removes the underlying DRM bridge etc, but this can be done on
the specific work rather than waiting for the flush of the system-wide
workqueue.
Fixes: bc6fa8676ebb ("drm/bridge/lontium-lt9611uxc: move HPD notification out of IRQ handler")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601233818.1877963-1-bjorn.andersson@linaro.org
|
|
of_graph_get_remote_node() returns remote device nodepointer with
refcount incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: e67f6037ae1b ("drm/meson: split out encoder from meson_dw_hdmi")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601033927.47814-3-linmq006@gmail.com
|
|
of_graph_get_remote_node() returns remote device nodepointer with
refcount incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: 318ba02cd8a8 ("drm/meson: encoder_cvbs: switch to bridge with ATTACH_NO_CONNECTOR")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601033927.47814-2-linmq006@gmail.com
|
|
The bits for accessing I2C data and clock channels varies among
models. Store them in the device-info structure for consumption
by the DDC code.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601112522.5774-11-tzimmermann@suse.de
|
|
Set new vidrst flag in device info for models that synchronize with
external sources (i.e., BMCs). In modesetting, set the corresponding
bits from the device-info flag.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601112522.5774-10-tzimmermann@suse.de
|
|
The maximum resolution and memory bandwidth are model-specific limits.
Both are used during display-mode validation. Store the values in struct
mgag200_device_info and simplify the validation code.
v2:
* 'bandwith' -> 'bandwidth' in commit message
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601112522.5774-9-tzimmermann@suse.de
|
|
Flag devices with broken handling of the startadd field in
struct mgag200_device_info, instead of PCI driver data. This
reduces the driver data to a simple type constant.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601112522.5774-8-tzimmermann@suse.de
|
|
While currently empty, struct mgag200_device_info, will provide static,
constant information on each device model.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601112522.5774-7-tzimmermann@suse.de
|
|
Rework mgag200_regs_init() and mgag200_mm_init() into device preinit
and init functions. The preinit function, mgag200_device_preinit(),
requests and maps a device's I/O and video memory. The init function,
mgag200_device_init() initializes the state of struct mga_device.
Splitting the initialization between the two functions is necessary
to perform per-model operations between the two calls, such as reading
the unique revision ID on G200SEs.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601112522.5774-6-tzimmermann@suse.de
|
|
Call mgag200_device_probe_vram() from each model's initializer. The
G200EW3 uses a special helper with additional instructions.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601112522.5774-5-tzimmermann@suse.de
|
|
Split the PCI code into a single call for each model. G200 and G200SE
each contain a dedicated helper with additional instructions. Noteably,
the G200ER has no code for PCI setup.
In a later patch, the magic numbers should be replaced by descriptive
constants.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601112522.5774-4-tzimmermann@suse.de
|
|
Add a separate initializer function for each model. Add separate
devic structures for G200 and G200SE, which require additional
information.
Also move G200's and G200SE's helpers for reading the BIOS and
version id into model-specific code.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601112522.5774-3-tzimmermann@suse.de
|
|
Remove old test for 32-bit vs 16-bit colors. Prefer 24-bit color depth
on all devices. 32-bit color depth doesn't exist, it should have always
been 24-bit.
G200SE with less than 2 MiB of video memory have defaulted to 16-bit
color depth, as the original revision of the G200SE had only 1.75 MiB
of video memory. Using 16-bit colors enabled XGA resolution. But we
now already limit these devices to VGA resolutions as the memory-bandwith
test assumes 32-bit pixel size. So drop the special case from color-depth
selection.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601112522.5774-2-tzimmermann@suse.de
|
|
If we're unable to read the EDID for a display because it's corrupt /
bogus / invalid then we'll add a set of standard modes for the
display. Since we have no true information about the connected
display, these modes are essentially guesses but better than nothing.
At the moment, none of the modes returned is marked as preferred, but
the modes are sorted such that the higher resolution modes are listed
first.
When userspace sees these modes presented by the kernel it needs to
figure out which one to pick. At least one userspace, ChromeOS [1]
seems to use the rules (which seem pretty reasonable):
1. Try to pick the first mode marked as preferred.
2. Try to pick the mode which matches the first detailed timing
descriptor in the EDID.
3. If no modes were marked as preferred then pick the first mode.
Unfortunately, userspace's rules combined with what the kernel is
doing causes us to fail section 4.2.2.6 (EDID Corruption Detection) of
the DP 1.4a Link CTS. That test case says that, while it's OK to allow
some implementation-specific fall-back modes if the EDID is bad that
userspace should _default_ to 640x480.
Let's fix this by marking 640x480 as default for DP in the no-EDID
case.
NOTES:
- In the discussion around v3 of this patch [2] there was talk about
solving this in userspace and I even implemented a patch that would
have solved this for ChromeOS, but then the discussion turned back
to solving this in the kernel.
- Also in the discussion of v3 [2] it was requested to limit this
change to just DP since folks were worried that it would break some
subtle corner case on VGA or HDMI.
[1] https://source.chromium.org/chromium/chromium/src/+/a051f741d0a15caff2251301efe081c30e0f4a96:ui/ozone/platform/drm/common/drm_util.cc;l=488
[2] https://lore.kernel.org/r/20220513130533.v3.1.I31ec454f8d4ffce51a7708a8092f8a6f9c929092@changeid
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601112302.v4.1.I31ec454f8d4ffce51a7708a8092f8a6f9c929092@changeid
|
|
TI DLPC3433 is a MIPI DSI based display controller bridge
for processing high resolution DMD based projectors.
It has a flexible configuration of MIPI DSI and DPI signal
input that produces a DMD output in RGB565, RGB666, RGB888
formats.
It supports upto 720p resolution with 60 and 120 Hz refresh
rates.
Add bridge driver for it.
Signed-off-by: Christopher Vollo <chris@renewoutreach.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220603140349.3563612-2-jagan@amarulasolutions.com
|
|
TI DLPC3433 is a MIPI DSI based display controller bridge
for processing high resolution DMD based projectors.
It has a flexible configuration of MIPI DSI and DPI signal
input that produces a DMD output in RGB565, RGB666, RGB888
formats.
It supports upto 720p resolution with 60 and 120 Hz refresh
rates.
Add dt-bingings for it.
Signed-off-by: Christopher Vollo <chris@renewoutreach.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220603140349.3563612-1-jagan@amarulasolutions.com
|
|
This check determines whether a given address is part of
image 0 or image 1. Image 1 starts at offset image0_size,
so that address should be included.
Fixes: 4d4e9907ff572 ("drm/nouveau/bios: guard against out-of-bounds accesses to image")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Timur Tabi <ttabi@nvidia.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220511163716.3520591-1-ttabi@nvidia.com
|
|
While it works, for the most part, to assume that the panel has
finished probing when devm_of_dp_aux_populate_ep_devices() returns,
it's a bit fragile. This is talked about at length in commit
a1e3667a9835 ("drm/bridge: ti-sn65dsi86: Promote the AUX channel to
its own sub-dev").
When reviewing the ps8640 code, I managed to convince myself that it
was OK not to worry about it there and that maybe it wasn't really
_that_ fragile. However, it turns out that it really is. Simply
hardcoding panel_edp_probe() to return -EPROBE_DEFER was enough to put
the boot process into an infinite loop. I believe this manages to trip
the same issues that we used to trip with the main MSM code where
something about our actions trigger Linux to re-probe previously
deferred devices right away and each time we try again we re-trigger
Linux to re-probe.
Let's fix this using the callback introduced in the patch ("drm/dp:
Callbacks to make it easier for drivers to use DP AUX bus properly").
When using the new callback, we have to be a little careful. The
probe_done() callback is no longer always called in the context of
our probe routine. That means we can't rely on being able to return
-EPROBE_DEFER from it. We re-jigger the order of things a bit to
account for that.
With this change, the device still boots (though obviously the panel
doesn't come up) if I force panel-edp to always return
-EPROBE_DEFER. If I fake it and make the panel probe exactly once it
also works.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510122726.v3.4.Ia6324ebc848cd40b4dbd3ad3289a7ffb5c197779@changeid
|
|
This adds a devm managed version of drm_bridge_add(). Like other
"devm" function listed in drm_bridge.h, this function takes an
explicit "dev" to use for the lifetime management. A few notes:
* In general we have a "struct device" for bridges that makes a good
candidate for where the lifetime matches exactly what we want.
* The "bridge->dev->dev" device appears to be the encoder
device. That's not the right device to use for lifetime management.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510122726.v3.3.Iba4b9bf6c7a1ee5ea2835ad7bd5eaf84d7688520@changeid
|
|
As talked about in this patch in the kerneldoc of
of_dp_aux_populate_ep_device() and also in the past in commit
a1e3667a9835 ("drm/bridge: ti-sn65dsi86: Promote the AUX channel to
its own sub-dev"), it can be difficult for eDP controller drivers to
know when the panel has finished probing when they're using
of_dp_aux_populate_ep_devices().
The ti-sn65dsi86 driver managed to solve this because it was already
broken up into a bunch of sub-drivers. That means we could solve the
problem there by adding a new sub-driver to get the panel. We could
use the traditional -EPROBE_DEFER retry mechansim to handle the case
where the panel hadn't probed yet.
In parade-ps8640 we didn't really solve this. The code just expects
the panel to be ready right away. While reviewing the code originally
I had managed to convince myself it was fine to just expect the panel
right away, but additional testing has shown that not to be the
case. We could fix parade-ps8640 like we did ti-sn65dsi86 but it's
pretty cumbersome (since we're not already broken into multiple
drivers) and requires a bunch of boilerplate code.
After discussion [1] it seems like the best solution for most people
is:
- Accept that there's always at most one device that will probe as a
result of the DP AUX bus (it may have sub-devices, but there will be
one device _directly_ probed).
- When that device finishes probing, we can just have a call back.
This patch implements that idea. We'll now take a callback as an
argument to the populate function. To make this easier to land in
pieces, we'll make wrappers for the old functions. The functions with
the new name (which make it clear that we only have one child) will
take the callback and the functions with the old name will temporarily
wrap.
[1] https://lore.kernel.org/r/CAD=FV=Ur3afHhsXe7a3baWEnD=MFKFeKRbhFU+bt3P67G0MVzQ@mail.gmail.com
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510122726.v3.2.I4182ae27e00792842cb86f1433990a0ef9c0a073@changeid
|
|
Someone made the mistake to try reading EDID from the backlight i2c
adapter. This has been wrong for a very long time but since we read out
the modes correctly on init and don't hotplug lvds it has been working
anyway. Correct this by using connector->ddc instead of
encoder->i2c_bus. Both PSB and CDV are affected but this bug.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601092311.22648-9-patrik.r.jakobsson@gmail.com
|
|
We're moving all uses of ddc_bus to drm_connector where they belong.
The initialization of the gma_i2c_chan for Oaktrail is a bit backwards
so it required improvements. Also cleanup the error handling in
oaktrail_lvds_init(). Since this is the last user of
gma_encoder->ddc_bus we can remove it.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601092311.22648-8-patrik.r.jakobsson@gmail.com
|
|
We're moving all uses of ddc_bus to drm_connector where they belong.
Also cleanup the error handling in cdv_intel_crt_init().
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601092311.22648-7-patrik.r.jakobsson@gmail.com
|
|
We're moving all uses of ddc_bus to drm_connector where they belong.
Also cleanup the error handling in psb_intel_lvds_init() and remove
unused ddc_bus in psb_intel_lvds_priv.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601092311.22648-6-patrik.r.jakobsson@gmail.com
|
|
We're moving all uses of ddc_bus from gma_encoder to drm_connector where
they belong. Also, cleanup the error handling in cdv_hdmi_init()
and remove unused i2c pointer in mid_intel_hdmi_priv.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601092311.22648-5-patrik.r.jakobsson@gmail.com
|
|
We're moving all uses of ddc_bus to drm_connector where they belong.
Also, add missing call to destroy ddc bus when destroying the connector
and cleanup the error handling in cdv_intel_lvds_init().
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601092311.22648-4-patrik.r.jakobsson@gmail.com
|
|
This makes it easier to get at the full gma_i2c_chan when having an
i2c_adapter from eg. drm_connector->ddc.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601092311.22648-3-patrik.r.jakobsson@gmail.com
|
|
psb_intel_i2c_chan is used by all chips so use the correct prefix.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601092311.22648-2-patrik.r.jakobsson@gmail.com
|
|
The kernel test robot reports a compile warning due the ssd130x_spi_table
variable being defined but not used. This happen when ssd130x-spi driver
is built-in instead of being built as a module, i.e:
CC drivers/gpu/drm/solomon/ssd130x-spi.o
AR drivers/base/firmware_loader/built-in.a
AR drivers/base/built-in.a
CC kernel/trace/trace.o
drivers/gpu/drm/solomon/ssd130x-spi.c:155:35: warning: ‘ssd130x_spi_table’ defined but not used [-Wunused-const-variable=]
155 | static const struct spi_device_id ssd130x_spi_table[] = {
| ^~~~~~~~~~~~~~~~~
The driver shouldn't need a SPI device ID table and only have an OF device
ID table, but the former is needed to workaround an issue in the SPI core.
This always reports a MODALIAS of the form "spi:<device>" even for devices
registered through Device Trees.
But the table is only needed when the driver built as a module to populate
the .ko alias info. It's not needed when the driver is built-in the kernel.
Fixes: 74373977d2ca ("drm/solomon: Add SSD130x OLED displays SPI support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220530140246.742469-1-javierm@redhat.com
|
|
sparse reports
drivers/gpu/drm/nouveau/nvkm/engine/fifo/gv100.c:56:1: warning: symbol 'gv100_fifo_runlist' was not declared. Should it be static?
gv100_fifo_runlist is only used in gv100.c, so change it to static.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220528141836.4155970-1-trix@redhat.com
|