| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We used to have several callers which just used arrays. They're
gone, so we can use sg_next() everywhere, simplifying the code.
On my laptop, this slowed down vring_bench by 15%:
vring_bench before:
936153354-967745359(9.44739e+08+/-6.1e+06)ns
vring_bench after:
1061485790-1104800648(1.08254e+09+/-6.6e+06)ns
However, a more realistic test using pktgen on a AMD FX(tm)-8320 saw
a few percent improvement:
pktgen before:
767390-792966(785159+/-6.5e+03)pps 356-367(363.75+/-2.9)Mb/sec (356068960-367936224(3.64314e+08+/-3e+06)bps) errors: 0
pktgen after:
787781-796334(793165+/-2.4e+03)pps 365-369(367.5+/-1.2)Mb/sec (365530384-369498976(3.68028e+08+/-1.1e+06)bps) errors: 0
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is the only driver which doesn't hand virtqueue_add_inbuf and
virtqueue_add_outbuf a well-formed, well-terminated sg. Fix it,
so we can make virtio_add_* simpler.
pktgen results:
modprobe pktgen
echo 'add_device eth0' > /proc/net/pktgen/kpktgend_0
echo nowait 1 > /proc/net/pktgen/eth0
echo count 1000000 > /proc/net/pktgen/eth0
echo clone_skb 100000 > /proc/net/pktgen/eth0
echo dst_mac 4e:14:25:a9:30:ac > /proc/net/pktgen/eth0
echo dst 192.168.1.2 > /proc/net/pktgen/eth0
for i in `seq 20`; do echo start > /proc/net/pktgen/pgctrl; tail -n1 /proc/net/pktgen/eth0; done
Before:
746547-793084(786421+/-9.6e+03)pps 346-367(364.4+/-4.4)Mb/sec (346397808-367990976(3.649e+08+/-4.5e+06)bps) errors: 0
After:
767390-792966(785159+/-6.5e+03)pps 356-367(363.75+/-2.9)Mb/sec (356068960-367936224(3.64314e+08+/-3e+06)bps) errors: 0
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-09-12
This series contains updates to e1000, ixgbe and ixgbevf.
Mark provide two fixes to reduce compile warnings produce by ixgbe
and ixgbevf.
Alex provides two patches for ixgbe, first removes the receive buffer
allocation at the end of the ixgbe_clean_rx_irq(). The reason for
removing this is to avoid the extra latency introduced by the MMIO write.
Second patch addresses several issues in the current ixgbe implementation
of busy poll sockets. It was possible for frames to be delivered out of
order if they were held in GRO, so address this by flushing the GRO
buffers before releasing the q_vector back to the idle state. Also, we
were having to take a spinlock on changing the state to and from idle,
so to resolve this, replaced the state value with an atomic and use
atomic_cmpxchg to change the value from idle, and a simple atomic set
to restore it back to idle after we have acquired it. This allows us
to only use a locked operation on acquiring the vector without a need
for a locked operation to release it.
Florian Westphal provides several patches for e1000 which does some
cleanup and updating of the driver. Moved e1000_tbi_adjust_stats()
so that he could make the function static. Added a helper function
to deal with the tbi workaround that was located in 2 different
Rx clean functions. Added a e1000_rx_buffer struct for use on receive
since the transmit and receive have different requirements. Updates
e1000 to use napi_gro_frags API.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
John Fastabend says:
====================
net/sched rcu classifiers and tcf
This series converts the tcf_proto usage to RCU.
This requires updating each classifier individually to handle the
new copy/update requirement and also to update the core list
traversals. This makes the assumption that updates to the tables
are infrequent in comparison to the packet per second being
classified. On a 10Gbps running near line rate we can easily
produce 12+ million packets per second so IMO this is a reasonable
assumption. The updates are serialized by RTNL.
I have done some basic testing on this series and do not see any
immediate splats or issues. The patch series has been running
on my dev systems for a month or so now and I've not seen any
issues. Although my configurations are not overly complicated.
My test cases at this point cover all the filters with a
tight loop to add/remove filters. Some basic estimator tests
where I add an estimator to the qdisc and verify the statistics
accurate using pktgen. And finally I have a small script to
exercise the 'tc actions' interface. Feel free to send me more
tests off list and I can run them.
This is prep work to drop the qdisc lock with the first
target being the ingress qdisc. To be done is making the
tc actions RCU safe and statistics per cpu. These patches
are in the works.
Comments:
- Checkpatch is still giving errors on some >80 char lines I know
about this. IMO the way to fix this is to restructure the sched
code to avoid being so heavily indented. But doing this here
bloats the patchset and anyways there are already lots of >80
chars in these files. I would prefer to keep the patches as is
but let me know if others think I should fix these and I will.
A follow up patch set could restructure the code and fix this
throughout the code blocks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes the cls_bpf classifier RCU safe. The tcf_lock
was being used to protect a list of cls_bpf_prog now this list
is RCU safe and updates occur with rcu_replace.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make cls_u32 classifier safe to run without holding lock. This patch
converts statistics that are kept in read section u32_classify into
per cpu counters.
This patch was tested with a tight u32 filter add/delete loop while
generating traffic with pktgen. By running pktgen on vlan devices
created on top of a physical device we can hit the qdisc layer
correctly. For ingress qdisc's a loopback cable was used.
for i in {1..100}; do
q=`echo $i%8|bc`;
echo -n "u32 tos: iteration $i on queue $q";
tc filter add dev p3p2 parent $p prio $i u32 match ip tos 0x10 0xff \
action skbedit queue_mapping $q;
sleep 1;
tc filter del dev p3p2 prio $i;
echo -n "u32 tos hash table: iteration $i on queue $q";
tc filter add dev p3p2 parent $p protocol ip prio $i handle 628: u32 divisor 1
tc filter add dev p3p2 parent $p protocol ip prio $i u32 \
match ip protocol 17 0xff link 628: offset at 0 mask 0xf00 shift 6 plus 0
tc filter add dev p3p2 parent $p protocol ip prio $i u32 \
ht 628:0 match ip tos 0x10 0xff action skbedit queue_mapping $q
sleep 2;
tc filter del dev p3p2 prio $i
sleep 1;
done
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This uses per cpu counters in cls_u32 in preparation
to convert over to rcu.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make cls_tcindex RCU safe.
This patch addds a new RCU routine rcu_dereference_bh_rtnl() to check
caller either holds the rcu read lock or RTNL. This is needed to
handle the case where tcindex_lookup() is being called in both cases.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RCUify the route classifier. For now however spinlock's are used to
protect fastmap cache.
The issue here is the fastmap may be read by one CPU while the
cache is being updated by another. An array of pointers could be
one possible solution.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RCU'ify fw classifier.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make cgroup classifier safe for RCU.
Also drops the calls in the classify routine that were doing a
rcu_read_lock()/rcu_read_unlock(). If the rcu_read_lock() isn't held
entering this routine we have issues with deleting the classifier
chain so remove the unnecessary rcu_read_lock()/rcu_read_unlock()
pair noting all paths AFAIK hold rcu_read_lock.
If there is a case where classify is called without the rcu read lock
then an rcu splat will occur and we can correct it.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable basic classifier for RCU.
Dereferencing tp->root may look a bit strange here but it is needed
by my accounting because it is allocated at init time and needs to
be kfree'd at destroy time. However because it may be referenced in
the classify() path we must wait an RCU grace period before free'ing
it. We use kfree_rcu() and rcu_ APIs to enforce this. This pattern
is used in all the classifiers.
Also the hgenerator can be incremented without concern because it
is always incremented under RTNL.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rcu'ify tcf_proto this allows calling tc_classify() without holding
any locks. Updaters are protected by RTNL.
This patch prepares the core net_sched infrastracture for running
the classifier/action chains without holding the qdisc lock however
it does nothing to ensure cls_xxx and act_xxx types also work without
locking. Additional patches are required to address the fall out.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add __rcu notation to qdisc handling by doing this we can make
smatch output more legible. And anyways some of the cases should
be using rcu_dereference() see qdisc_all_tx_empty(),
qdisc_tx_chainging(), and so on.
Also *wake_queue() API is commonly called from driver timer routines
without rcu lock or rtnl lock. So I added rcu_read_lock() blocks
around netif_wake_subqueue and netif_tx_wake_queue.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes the cls_bpf classifier RCU safe. The tcf_lock
was being used to protect a list of cls_bpf_prog now this list
is RCU safe and updates occur with rcu_replace.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make cls_u32 classifier safe to run without holding lock. This patch
converts statistics that are kept in read section u32_classify into
per cpu counters.
This patch was tested with a tight u32 filter add/delete loop while
generating traffic with pktgen. By running pktgen on vlan devices
created on top of a physical device we can hit the qdisc layer
correctly. For ingress qdisc's a loopback cable was used.
for i in {1..100}; do
q=`echo $i%8|bc`;
echo -n "u32 tos: iteration $i on queue $q";
tc filter add dev p3p2 parent $p prio $i u32 match ip tos 0x10 0xff \
action skbedit queue_mapping $q;
sleep 1;
tc filter del dev p3p2 prio $i;
echo -n "u32 tos hash table: iteration $i on queue $q";
tc filter add dev p3p2 parent $p protocol ip prio $i handle 628: u32 divisor 1
tc filter add dev p3p2 parent $p protocol ip prio $i u32 \
match ip protocol 17 0xff link 628: offset at 0 mask 0xf00 shift 6 plus 0
tc filter add dev p3p2 parent $p protocol ip prio $i u32 \
ht 628:0 match ip tos 0x10 0xff action skbedit queue_mapping $q
sleep 2;
tc filter del dev p3p2 prio $i
sleep 1;
done
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This uses per cpu counters in cls_u32 in preparation
to convert over to rcu.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make cls_tcindex RCU safe.
This patch addds a new RCU routine rcu_dereference_bh_rtnl() to check
caller either holds the rcu read lock or RTNL. This is needed to
handle the case where tcindex_lookup() is being called in both cases.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RCUify the route classifier. For now however spinlock's are used to
protect fastmap cache.
The issue here is the fastmap may be read by one CPU while the
cache is being updated by another. An array of pointers could be
one possible solution.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RCU'ify fw classifier.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make cgroup classifier safe for RCU.
Also drops the calls in the classify routine that were doing a
rcu_read_lock()/rcu_read_unlock(). If the rcu_read_lock() isn't held
entering this routine we have issues with deleting the classifier
chain so remove the unnecessary rcu_read_lock()/rcu_read_unlock()
pair noting all paths AFAIK hold rcu_read_lock.
If there is a case where classify is called without the rcu read lock
then an rcu splat will occur and we can correct it.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable basic classifier for RCU.
Dereferencing tp->root may look a bit strange here but it is needed
by my accounting because it is allocated at init time and needs to
be kfree'd at destroy time. However because it may be referenced in
the classify() path we must wait an RCU grace period before free'ing
it. We use kfree_rcu() and rcu_ APIs to enforce this. This pattern
is used in all the classifiers.
Also the hgenerator can be incremented without concern because it
is always incremented under RTNL.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rcu'ify tcf_proto this allows calling tc_classify() without holding
any locks. Updaters are protected by RTNL.
This patch prepares the core net_sched infrastracture for running
the classifier/action chains without holding the qdisc lock however
it does nothing to ensure cls_xxx and act_xxx types also work without
locking. Additional patches are required to address the fall out.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add __rcu notation to qdisc handling by doing this we can make
smatch output more legible. And anyways some of the cases should
be using rcu_dereference() see qdisc_all_tx_empty(),
qdisc_tx_chainging(), and so on.
Also *wake_queue() API is commonly called from driver timer routines
without rcu lock or rtnl lock. So I added rcu_read_lock() blocks
around netif_wake_subqueue and netif_tx_wake_queue.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When sending out a burst of packets across multiple descriptors,
it is sufficient to send one LDC "start" trigger for
the first descriptor, so do not send an LDC "start" for every
pass through vnet_start_xmit. Similarly, it is sufficient to send
one "DRING_STOPPED" trigger for the last dring (and if that
fails, hold off and send the trigger later).
Optimizations to the number of LDC messages helps avoid
filling up the LDC channel with superfluous LDC messages
that risk triggering flow-control on the channel,
and also boosts performance.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Raghuram Kothakota <raghuram.kothakota@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
calling ether_setup is redundant since alloc_etherdev calls
it.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It will use pr_info_one() to print the version info of the
driver in probe function only once. No need to use the static
variable here.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 2abb7cdc0d ("udp: Add support for doing checksum unnecessary
conversion") caused napi_gro_cb structs with the "flush" field zero to
take the "udp_gro_receive" path rather than the "set flush to 1" path
that they would previously take. As a result I saw booting from an NFS
root hang shortly after starting userspace, with "server not
responding" messages.
This change to the handling of "flush == 0" packets appears to be
incidental to the goal of adding new code in the case where
skb_gro_checksum_validate_zero_check() returns zero. Based on that and
the fact that it breaks things, I'm assuming that it is unintentional.
Fixes: 2abb7cdc0d ("udp: Add support for doing checksum unnecessary conversion")
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexander Duyck says:
====================
Address reference counting issues with sock_queue_err_skb
After looking over the code for skb_clone_sk after some comments made by
Eric Dumazet I have come to the conclusion that skb_clone_sk is taking the
correct approach in how to handle the sk_refcnt when creating a buffer that
is eventually meant to be returned to the socket via the sock_queue_err_skb
function.
However upon review of other callers I found what I believe to be a
possible reference count issue in the path for handling "wifi ack" packets.
To address this I have applied the same logic that is currently in place so
that the sk_refcnt will be forced to stay at least 1, or we will not
provide an skb to return in the sk_error_queue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a possible issue with the use, or lack thereof of sk_refcnt and
sk_wmem_alloc in the wifi ack status functionality.
Specifically if a socket were to request acknowledgements, and the socket
were to have sk_refcnt drop to 0 resulting in it waiting on sk_wmem_alloc
to reach 0 it would be possible to have sock_queue_err_skb orphan the last
buffer, resulting in __sk_free being called on the socket. After this the
buffer is enqueued on sk_error_queue, however the queue has already been
flushed resulting in at least a memory leak, if not a data corruption.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change adds some documentation to the call skb_clone_sk. This is
meant to help clarify the purpose of the function for other developers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit c801e3cc1925 ("ipv4: Clarify in docs that accept_local requires rp_filter.").
It is not needed anymore since commit 1dced6a85482 ("ipv4: Restore accept_local behaviour in fib_validate_source()").
Suggested-by: Julian Anastasov <ja@ssi.bg>
Cc: Gregory Detal <gregory.detal@uclouvain.be>
Cc: Christoph Paasch <christoph.paasch@uclouvain.be>
Cc: Hannes Frederic Sowa <hannes@redhat.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Sébastien Barré <sebastien.barre@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
napi_gro_frags allows skb re-use in case GRO can merge payload pages
into an skb on the GRO lists.
netperf TCP_STREAM, kvm-e1000 emulation, mtu 9k:
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
old: 87380 16384 16384 30.00 8985.78
new: 87380 16384 16384 30.00 9907.05
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Instead of preallocating Rx skbs, allocate them right before sending
inbound packet up the stack.
e1000-kvm, mtu1500, netperf TCP_STREAM:
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
old: 87380 16384 16384 60.00 4532.40
new: 87380 16384 16384 60.00 4599.05
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
and remove *page, its only used for Rx.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
e1000 uses the same metadata struct for Rx and Tx. But Tx and Rx have
different requirements.
For Rx, we only need to store a buffer and a DMA address.
Follow-up patch will remove skb for Rx, bringing rx_buffer_info down
to 16 bytes on x86_64.
[ buffer_info is 48 bytes ]
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently we unmap the DMA range, then copy to new skb.
Change this so we can keep the mapping in case the data is copied.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Its the same in both handlers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
... and make it static.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change addresses several issues in the current ixgbe implementation of
busy poll sockets.
First was the fact that it was possible for frames to be delivered out of
order if they were held in GRO. This is addressed by flushing the GRO buffers
before releasing the q_vector back to the idle state.
The other issue was the fact that we were having to take a spinlock on
changing the state to and from idle. To resolve this I have replaced the
state value with an atomic and use atomic_cmpxchg to change the value from
idle, and a simple atomic set to restore it back to idle after we have
acquired it. This allows us to only use a locked operation on acquiring the
vector without a need for a locked operation to release it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change removes the Rx buffer allocation at the end of ixgbe_clean_rx_irq.
The reason for removing this is to avoid the extra latency introduced by the
MMIO write. This can amount to somewhere around an extra 100ns of latency and
one extra message worth of PCIe bus overhead.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Resolve missing-field-initializers warnings by using
designated initialization.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch resolves warnings produced by ixgbe in W=2 kernel
builds. There are missing-field-initializers warnings and shadow
warnings. None of these point to any deeper problem, so just
resolve them so any new warnings get analyzed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since BPF JIT depends on the availability of module_alloc() and
module_free() helpers (HAVE_BPF_JIT and MODULES), we better build
that code only in case we have BPF_JIT in our config enabled, just
like with other JIT code. Fixes builds for arm/marzen_defconfig
and sh/rsk7269_defconfig.
====================
kernel/built-in.o: In function `bpf_jit_binary_alloc':
/home/cwang/linux/kernel/bpf/core.c:144: undefined reference to `module_alloc'
kernel/built-in.o: In function `bpf_jit_binary_free':
/home/cwang/linux/kernel/bpf/core.c:164: undefined reference to `module_free'
make: *** [vmlinux] Error 1
====================
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: 738cbe72adc5 ("net: bpf: consolidate JIT binary allocator")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hariprasad Shenai says:
====================
cxgb4: Allow FW size upto 1MB, support for S25FL032P flash and misc. fixes
This patch series adds support to allow FW size upto 1MB, support for S25FL032P
flash. Fix t4_flash_erase_sectors to throw an error, when erase sector aren't in
the flash and also warning message when adapters have flashes less than 2Mb.
Adds device id of new adapter and removes device id of debug adapter.
The patches series is created against 'net-next' tree.
And includes patches on cxgb4 driver and cxgb4vf driver.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
