| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
With the current RX RED/DROP levels of 192/184 for CQE_RX, when
packet incoming rate is high, LLC is getting polluted resulting
in more cache misses and higher latency in packet processing. This
slows down the whole process and performance loss. Hence reduced
the levels to 224/216 (ie for a CQ size of 1024, Rx pkts will be
red dropped or dropped when unused CQE are less than 128/160 respectively)
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sunil Goutham says:
====================
octeontx2: Flow control support and other misc changes
This patch series adds flow control support (802.3 pause frames) and
has other changes wrt generic admin function (AF) driver functionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently on the first check if the operation is still not
finished, the poll goes to sleep for 2-5 usecs. But if for
some reason (due to other priority stuff like interrupts etc) by
the time the poll wakes up the 10ms time is expired then we don't
check if operation is finished or not and return failure.
This patch modifies poll logic to check HW operation after sleep so
that the status is checked atleast twice.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bus mastering is enabled by firmware, but when this driver
is unbinded bus mastering gets disabled by the PCI subsystem
which results interrupts not working when driver is reloaded.
Hence set bus mastering everytime in probe().
Also
- Converted pci_set_dma_mask() and pci_set_consistent_dma_mask()
to dma_set_mask_and_coherent().
- Cleared transaction pending bit which gets set during
driver unbind due to clearing of bus mastering (ME bit).
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently there is no way for AF dependent drivers in
any domain to check if the AF driver is loaded. This
patch sets an ID for RVUM block which will automatically
reflects in PF/VFs discovery register which they can
check and defer their probe until AF is up.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For retrieving info like interface MAC addresses, packet
parser key extraction config etc currently a command
is sent to firmware and firmware which periodically polls
for commands, processes these and returns the info.
This is resulting in interface initialization taking lot
of time. To optimize this a memory region is shared between
firmware and this driver, firmware while booting puts
static info like these into that region for driver to
read directly without using commands.
With this
- Logic for retrieving packet parser extraction config
via commands is removed and repalced with using the
shared 'fwdata' structure.
- Now RVU MSIX vector address is also retrieved from this fwdata struct
instead of from CSR. Otherwise when kexec/kdump crash kernel loads
CSR will have a IOVA setup by primary kernel which impacts
RVU PF/VF's interrupts.
- Also added a mbox handler for PF/VF interfaces to retrieve their MAC
addresses from AF.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added mailbox requests to retrieve backpressure IDs from AF and Aura,
CQ contexts are configured with these BPIDs. So that when resource
levels reach configured thresholds they assert backpressure on the
interface which is also mapped to same BPID.
Also added support to enable/disable pause frames generation via ethtool.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CGX LMAC, the physical interface can generate pause frames when
internal resources asserts backpressure due to exhaustion.
This patch configures CGX to generate 802.3 pause frames.
Also enabled processing of received pause frames on the line which
will assert backpressure on the internal transmit path.
Also added mailbox handlers for PF drivers to enable or disable
pause frames anytime.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each of the interface receive channels can be backpressured by
resources upon exhaustion or reaching configured threshold levels.
Resources here are receive buffer queues (Auras) and pkt notification
descriptor queues (CQs). Resources and interface channels are mapped
using backpressure IDs (BPIDs).
HW supports upto 512 BPIDs, this patch divides these BPIDs statically
across CGX/LBK/SDP interfaces as follows.
BPIDs 0 - 191 are mapped to LMAC channels, 16 per LMAC.
BPIDs 192 - 255 are mapped to LBK channels.
BPIDs 256 - 511 are mapped to SDP channels.
Also did the needed basic configuration of BPIDs.
Added mbox handlers with which a PF device can request for a BPID which
it will use to configure Auras and CQs.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add constants for the used interrupts bits. This avoids the magic
number for MII_VSC85XX_INT_MASK_MASK.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'net-ethtool-Introduce-link_ksettings-API-for-virtual-network-devices'
Cris Forno says:
====================
net/ethtool: Introduce link_ksettings API for virtual network devices
This series provides an API for drivers of virtual network devices that
allows users to alter initial device speed and duplex settings to reflect
the actual capabilities of underlying hardware. The changes made include
a helper function ethtool_virtdev_set_link_ksettings, which is used to
retrieve alterable link settings. In addition, there is a new ethtool
function defined to validate those settings. These changes resolve code
duplication for existing virtual network drivers that have already
implemented this behavior. In the case of the ibmveth driver, this API is
used to provide this capability for the first time.
---
v7: - removed ethtool_validate_cmd function pointer parameter from
ethtool_virtdev_set_link_ksettings since none of the virtual drivers
pass in a custom validate function as suggested by Michal Kubecek.
v6: - removed netvsc_validate_ethtool_ss_cmd(). netvsc_drv now uses
ethtool_virtdev_validate_cmd() instead as suggested by Michal Kubecek
and approved by Haiyang Zhang.
- matched handler argument name of ethtool_virtdev_set_link_ksettings
in declaration and definition as suggested by Michal Kubecek.
- shortened validate variable assignment in
ethtool_virtdev_set_link_ksettings as suggested by Michal Kubecek.
v5: - virtdev_validate_link_ksettings is taken out of the ethtool global
structure and is instead added as an argument to
ethtool_virtdev_set_link_ksettings as suggested by Jakub Kicinski.
v4: - Cleaned up return statement in ethtool_virtdev_validate_cmd based
off of Michal Kubecek's and Thomas Falcon's suggestion.
- If the netvsc driver is using the VF device in order to get
accelerated networking, the real speed and duplex is reported by using
the VF device as suggested by Stephen Hemminger.
- The speed and duplex variables are now passed by value rather than
passed by pointer as suggested by Willem de Bruijin and Michal
Kubecek.
- Removed ethtool_virtdev_get_link_ksettings since it was too simple
to warrant a helper function.
v3: - Factored out duplicated code to core/ethtool to provide API to
virtual drivers
v2: - Updated default driver speed/duplex settings to avoid breaking
existing setups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the ethtool_virtdev_set_link_ksettings function in core/ethtool.c,
ibmveth, netvsc, and virtio now use the core's helper function.
Funtionality changes that pertain to ibmveth driver include:
1. Changed the initial hardcoded link speed to 1GB.
2. Added support for allowing a user to change the reported link
speed via ethtool.
Functionality changes to the netvsc driver include:
1. When netvsc_get_link_ksettings is called, it will defer to the VF
device if it exists to pull accelerated networking values, otherwise
pull default or user-defined values.
2. Similarly, if netvsc_set_link_ksettings called and a VF device
exists, the real values of speed and duplex are changed.
Signed-off-by: Cris Forno <cforno12@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Three virtual devices (ibmveth, virtio_net, and netvsc) all have
similar code to set link settings and validate ethtool command. To
eliminate duplication of code, it is factored out into core/ethtool.c.
Signed-off-by: Cris Forno <cforno12@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Taehee Yoo says:
====================
hsr: several code cleanup for hsr module
This patchset is to clean up hsr module code.
1. The first patch is to use debugfs_remove_recursive().
If it uses debugfs_remove_recursive() instead of debugfs_remove(),
hsr_priv() doesn't need to have "node_tbl_file" pointer variable.
2. The second patch is to use extack error message.
If HSR uses the extack instead of netdev_info(), users can get
error messages immediately without any checking the kernel message.
3. The third patch is to use netdev_err() instead of WARN_ONCE().
When a packet is being sent, hsr_addr_subst_dest() is called and
it tries to find the node with the ethernet destination address.
If it couldn't find a node, it warns with WARN_ONCE().
But, using WARN_ONCE() is a little bit overdoing.
So, in this patch, netdev_err() is used instead.
4. The fourth patch is to remove unnecessary rcu_read_{lock/unlock}().
There are some rcu_read_{lock/unlock}() in hsr module and some of
them are unnecessary. In this patch,
these unnecessary rcu_read_{lock/unlock}() will be removed.
5. The fifth patch is to use upper/lower device infrastructure.
netdev_upper_dev_link() is useful to manage lower/upper interfaces.
And this function internally validates looping, maximum depth.
If hsr module uses upper/lower device infrastructure,
it can prevent these above problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev_upper_dev_link() is useful to manage lower/upper interfaces.
And this function internally validates looping, maximum depth.
All or most virtual interfaces that could have a real interface
(e.g. macsec, macvlan, ipvlan etc.) use lower/upper infrastructure.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to access the port list, the hsr_port_get_hsr() is used.
And this is protected by RTNL and RCU.
The hsr_fill_info(), hsr_check_carrier(), hsr_dev_open() and
hsr_get_max_mtu() are protected by RTNL.
So, rcu_read_lock() in these functions are not necessary.
The hsr_handle_frame() also uses rcu_read_lock() but this function
is called by packet path.
It's already protected by RCU.
So, the rcu_read_lock() in hsr_handle_frame() can be removed.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When HSR interface is sending a frame, it finds a node with
the destination ethernet address from the list.
If there is no node, it calls WARN_ONCE().
But, using WARN_ONCE() for this situation is a little bit overdoing.
So, in this patch, the netdev_err() is used instead.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If HSR uses the extack instead of netdev_info(), users can get
error messages immediately without any checking the kernel message.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If it uses debugfs_remove_recursive() instead of debugfs_remove(),
hsr_priv() doesn't need to have "node_tbl_file" pointer variable.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The port to phylink was done as close as possible to initial
functionality.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Esben Haabendal says:
====================
net: ll_temac: RX/TX ring size and coalesce ethtool parameters
This series adds support for RX/TX ring size and irq coalesce ethtool
parameters to ll_temac driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Please note that the delays are calculated based on typical
parameters. But as TEMAC is an HDL IP, designs may vary, and future
work might be needed to make this calculation configurable.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for setting the RX and TX ring sizes for this driver using
ethtool. Also increase the default RX ring size as the previous default
was far too low for good performance in some configurations.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The start_p variable was included in the initial commit,
commit 92744989533c ("net: add Xilinx ll_temac device driver"),
but has never had any real use.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tx_bd_next field was included in the initial commit,
commit 92744989533c ("net: add Xilinx ll_temac device driver"),
but has never had any real use.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-02-28
The following pull-request contains BPF updates for your *net-next* tree.
We've added 41 non-merge commits during the last 7 day(s) which contain
a total of 49 files changed, 1383 insertions(+), 499 deletions(-).
The main changes are:
1) BPF and Real-Time nicely co-exist.
2) bpftool feature improvements.
3) retrieve bpf_sk_storage via INET_DIAG.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paolo Abeni says:
====================
net: cleanup datagram receive helpers
Several receive helpers have an optional destructor argument, which uglify
the code a bit and is taxed by retpoline overhead.
This series refactor the code so that we can drop such optional argument,
cleaning the helpers a bit and avoiding an indirect call in fast path.
The first patch refactor a bit the caller, so that the second patch
actually dropping the argument is more straight-forward
v1 -> v2:
- call scm_stat_del() only when not peeking - Kirill
- fix build issue with CONFIG_INET_ESPINTCP
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The only users for such argument are the UDP protocol and the UNIX
socket family. We can safely reclaim the accounted memory directly
from the UDP code and, after the previous patch, we can do scm
stats accounting outside the datagram helpers.
Overall this cleans up a bit some datagram-related helpers, and
avoids an indirect call per packet in the UDP receive path.
v1 -> v2:
- call scm_stat_del() only when not peeking - Kirill
- fix build issue with CONFIG_INET_ESPINTCP
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So the scm_stat_{add,del} helper can be invoked with no
additional lock held.
This clean-up the code a bit and will make the next
patch easier.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
Lastly, fix the following checkpatch warning:
CHECK: Prefer kernel type 'u8' over 'uint8_t'
#50: FILE: net/l2tp/l2tp_core.h:119:
+ uint8_t priv[]; /* private data */
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-02-27
mlx5 misc updates and minor cleanups:
1) Use per vport tables for mirroring
2) Improve log messages for SW steering (DR)
3) Add devlink fdb_large_groups parameter
4) E-Switch, Allow goto earlier chain
5) Don't allow forwarding between uplink representors
6) Add support for devlink-port in non-representors mode
7) Minor misc cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
