| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Checking for ifdef CONFIG_x fails if CONFIG_x=m.
Use IS_ENABLED instead, which is true for both built-ins and modules.
Otherwise, a
> ip -4 route add 1.2.3.4/32 via inet6 fe80::2 dev eth1
fails with the message "Error: IPv6 support not enabled in kernel." if
CONFIG_IPV6 is `m`.
In the spirit of b8127113d01e53adba15b41aefd37b90ed83d631.
Fixes: d15662682db2 ("ipv4: Allow ipv6 gateway with ipv4 routes")
Cc: Kim Phillips <kim.phillips@arm.com>
Signed-off-by: Florian Klink <flokli@flokli.de>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20201115224509.2020651-1-flokli@flokli.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The code refactoring of ILT configuration was not complete, the old
unused variables were used for the SRC block. That could lead to the memory
corruption by HW when rx filters are configured.
This patch completes that refactoring.
Fixes: 8a52bbab39c9 (qed: Debug feature: ilt and mdump)
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Link: https://lore.kernel.org/r/20201116132944.2055-1-dbogdanov@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
nlmsg_cancel() needs to be called in the error path of
inet_req_diag_fill to cancel the message.
Fixes: d545caca827b ("net: inet: diag: expose the socket mark to privileged processes.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Link: https://lore.kernel.org/r/20201116082018.16496-1-wanghai38@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In async_resync mode, we log the TCP seq of records until the async request
is completed. Later, in case one of the logged seqs matches the resync
request, we return it, together with its record serial number. Before this
fix, we mistakenly returned the serial number of the current record
instead.
Fixes: ed9b7646b06a ("net/tls: Add asynchronous resync")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Link: https://lore.kernel.org/r/20201115131448.2702-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If THIS_MODULE is not set, the module would be removed while debugfs is
being used.
It eventually makes kernel panic.
Fixes: 82c93a87bf8b ("netdevsim: implement couple of testing devlink health reporters")
Fixes: 424be63ad831 ("netdevsim: add UDP tunnel port offload support")
Fixes: 4418f862d675 ("netdevsim: implement support for devlink region and snapshots")
Fixes: d3cbb907ae57 ("netdevsim: add ACL trap reporting cookie as a metadata")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20201115103041.30701-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Due to a hardware issue, an access to MDIO registers
that is concurrent with other ENETC register accesses
may lead to the MDIO access being dropped or corrupted.
The workaround introduces locking for all register accesses
to the ENETC register space. To reduce performance impact,
a readers-writers locking scheme has been implemented.
The writer in this case is the MDIO access code (irrelevant
whether that MDIO access is a register read or write), and
the reader is any access code to non-MDIO ENETC registers.
Also, the datapath functions acquire the read lock fewer times
and use _hot accessors. All the rest of the code uses the _wa
accessors which lock every register access.
The commit introducing MDIO support is -
commit ebfcb23d62ab ("enetc: Add ENETC PF level external MDIO support")
but due to subsequent refactoring this patch is applicable on
top of a later commit.
Fixes: 6517798dd343 ("enetc: Make MDIO accessors more generic and export to include/linux/fsl")
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201112182608.26177-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
During loss recovery, retransmitted packets are forced to use TCP
timestamps to calculate the RTT samples, which have a millisecond
granularity. BBR is designed using a microsecond granularity. As a
result, multiple RTT samples could be truncated to the same RTT value
during loss recovery. This is problematic, as BBR will not enter
PROBE_RTT if the RTT sample is <= the current min_rtt sample, meaning
that if there are persistent losses, PROBE_RTT will constantly be
pushed off and potentially never re-entered. This patch makes sure
that BBR enters PROBE_RTT by checking if RTT sample is < the current
min_rtt sample, rather than <=.
The Netflix transport/TCP team discovered this bug in the Linux TCP
BBR code during lab tests.
Fixes: 0f8782ea1497 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Ryan Sharpelletti <sharpelletti@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Link: https://lore.kernel.org/r/20201116174412.1433277-1-sharpelletti.kdev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When removing the driver we would hit BUG_ON(!list_empty(&dev->ptype_specific))
in net/core/dev.c due to still having the NC-SI packet handler
registered.
# echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/unbind
------------[ cut here ]------------
kernel BUG at net/core/dev.c:10254!
Internal error: Oops - BUG: 0 [#1] SMP ARM
CPU: 0 PID: 115 Comm: sh Not tainted 5.10.0-rc3-next-20201111-00007-g02e0365710c4 #46
Hardware name: Generic DT based system
PC is at netdev_run_todo+0x314/0x394
LR is at cpumask_next+0x20/0x24
pc : [<806f5830>] lr : [<80863cb0>] psr: 80000153
sp : 855bbd58 ip : 00000001 fp : 855bbdac
r10: 80c03d00 r9 : 80c06228 r8 : 81158c54
r7 : 00000000 r6 : 80c05dec r5 : 80c05d18 r4 : 813b9280
r3 : 813b9054 r2 : 8122c470 r1 : 00000002 r0 : 00000002
Flags: Nzcv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none
Control: 00c5387d Table: 85514008 DAC: 00000051
Process sh (pid: 115, stack limit = 0x7cb5703d)
...
Backtrace:
[<806f551c>] (netdev_run_todo) from [<80707eec>] (rtnl_unlock+0x18/0x1c)
r10:00000051 r9:854ed710 r8:81158c54 r7:80c76bb0 r6:81158c10 r5:8115b410
r4:813b9000
[<80707ed4>] (rtnl_unlock) from [<806f5db8>] (unregister_netdev+0x2c/0x30)
[<806f5d8c>] (unregister_netdev) from [<805a8180>] (ftgmac100_remove+0x20/0xa8)
r5:8115b410 r4:813b9000
[<805a8160>] (ftgmac100_remove) from [<805355e4>] (platform_drv_remove+0x34/0x4c)
Fixes: bd466c3fb5a4 ("net/faraday: Support NCSI mode")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201117024448.1170761-1-joel@jms.id.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 39a6f4bce6b4 ("b44: replace the ssb_dma API with the generic DMA API")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1605582131-36735-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 469981b17a4f ("qed: Add unaligned and packed packet processing")
Fixes: fcb39f6c10b2 ("qed: Add mpa buffer descriptors for storing and processing mpa fpdus")
Fixes: 1e28eaad07ea ("qed: Add iWARP support for fpdu spanned over more than two tcp packets")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Link: https://lore.kernel.org/r/1605532033-27373-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Michael Chan says:
====================
bnxt_en: Bug fixes.
This first patch fixes a module eeprom A2h addressing issue. The next
2 patches fix counter related issues. The last one skips an
unsupported firmware call on the VF to avoid the error log.
====================
Link: https://lore.kernel.org/r/1605486472-28156-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
VFs do not have access permissions to issue NVM_GET_DEV_INFO
firmware command.
Fixes: 4933f6753b50 ("bnxt_en: Add bnxt_hwrm_nvm_get_dev_info() to query NVM info.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bnxt_add_one_ctr() adds a hardware counter to a software counter and
adjusts for the hardware counter wraparound against the mask. The logic
assumes that the hardware counter is always smaller than or equal to
the mask.
This assumption is mostly correct. But in some cases if the firmware
is older and does not provide the accurate mask, the driver can use
a mask that is smaller than the actual hardware mask. This can cause
some extra carry bits to be added to the software counter, resulting in
counters that far exceed the actual value. Fix it by masking the
hardware counter with the mask passed into bnxt_add_one_ctr().
Fixes: fea6b3335527 ("bnxt_en: Accumulate all counters.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Firmware is unable to retain the port counters during any kind of
fatal or non-fatal resets, so we must clear the port counters to
avoid false detection of port counter overflow.
Fixes: fea6b3335527 ("bnxt_en: Accumulate all counters.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The module eeprom address range returned by bnxt_get_module_eeprom()
should be 256 bytes of A0h address space, the lower half of the A2h
address space, and page 0 for the upper half of the A2h address space.
Fix the firmware call by passing page_number 0 for the A2h slave address
space.
Fixes: 42ee18fe4ca2 ("bnxt_en: Add Support for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPRO")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Transactions sit on one of several lists, depending on their state
(allocated, pending, complete, or polled). A spinlock protects
against concurrent access when transactions are moved between these
lists.
Transactions are also reference counted. A newly-allocated
transaction has an initial count of 1; a transaction is released in
gsi_trans_free() only if its decremented reference count reaches 0.
Releasing a transaction includes removing it from the polled (or if
unused, allocated) list, so the spinlock is acquired when we release
a transaction.
The reference count is used to allow a caller to synchronously wait
for a committed transaction to complete. In this case, the waiter
takes an extra reference to the transaction *before* committing it
(so it won't be freed), and releases its reference (calls
gsi_trans_free()) when it is done with it.
Similarly, gsi_channel_update() takes an extra reference to ensure a
transaction isn't released before the function is done operating on
it. Until the transaction is moved to the completed list (by this
function) it won't be freed, so this reference is taken "safely."
But in the quiesce path, we want to wait for the "last" transaction,
which we find in the completed or polled list. Transactions on
these lists can be freed at any time, so we (try to) prevent that
by taking the reference while holding the spinlock.
Currently gsi_trans_free() decrements a transaction's reference
count unconditionally, acquiring the lock to remove the transaction
from its list *only* when the count reaches 0. This does not
protect the quiesce path, which depends on the lock to ensure its
extra reference prevents release of the transaction.
Fix this by only dropping the last reference to a transaction
in gsi_trans_free() while holding the spinlock.
Fixes: 9dd441e4ed575 ("soc: qcom: ipa: GSI transactions")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201114182017.28270-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If tcp socket has more data than Encrypted Handshake Message then
tls_sw_recvmsg will try to decrypt next record instead of returning
full control message to userspace as mentioned in comment. The next
message - usually Application Data - gets corrupted because it uses
zero copy for decryption that's why the data is not stored in skb
for next iteration. Revert check to not decrypt next record if
current is not Application Data.
Fixes: 692d7b5d1f91 ("tls: Fix recvmsg() to be able to peek across multiple records")
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Link: https://lore.kernel.org/r/1605413760-21153-1-git-send-email-vfedorenko@novek.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
During rmnet unregistration, the real device rx_handler is first cleared
followed by the removal of rx_handler_data after the rcu synchronization.
Any packets in the receive path may observe that the rx_handler is NULL.
However, there is no check when dereferencing this value to use the
rmnet_port information.
This fixes following splat by adding the NULL check.
Unable to handle kernel NULL pointer dereference at virtual
address 000000000000000d
pc : rmnet_rx_handler+0x124/0x284
lr : rmnet_rx_handler+0x124/0x284
rmnet_rx_handler+0x124/0x284
__netif_receive_skb_core+0x758/0xd74
__netif_receive_skb+0x50/0x17c
process_backlog+0x15c/0x1b8
napi_poll+0x88/0x284
net_rx_action+0xbc/0x23c
__do_softirq+0x20c/0x48c
Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Link: https://lore.kernel.org/r/1605298325-3705-1-git-send-email-subashab@codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Recycle the page running page_pool_put_full_page() in
mvneta_swbm_add_rx_fragment routine when the last descriptor
contains just the FCS or if the received packet contains more than
MAX_SKB_FRAGS fragments
Fixes: ca0e014609f0 ("net: mvneta: move skb build after descriptors processing")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/df6a2bad70323ee58d3901491ada31c1ca2a40b9.1605291228.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix an issue where dump stack is printed on suspend resume flow due to
netif_set_real_num_rx_queues() is not called with rtnl_lock held().
Fixes: 686cff3d7022 ("net: stmmac: Fix incorrect location to set real_num_rx|tx_queues")
Reported-by: Christophe ROULLIER <christophe.roullier@st.com>
Tested-by: Christophe ROULLIER <christophe.roullier@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Reviewed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Link: https://lore.kernel.org/r/20201115074210.23605-1-vee.khee.wong@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In br_forward.c and br_input.c fields dev->stats.tx_dropped and
dev->stats.multicast are populated, but they are ignored in
ndo_get_stats64.
Fixes: 28172739f0a2 ("net: fix 64 bit counters on 32 bit arches")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/58ea9963-77ad-a7cf-8dfd-fc95ab95f606@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 83a8471ba255 ("net: ethernet: ti: cpsw: refactor probe to group common hw initialization")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605250173-18438-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 9efc9b2b04c7 ("net: stmmac: Add dwmac-intel-plat for GBE driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605249243-17262-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 3ced0a88cd4c ("qlcnic: Add support to run firmware POST")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605248186-16013-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: ca139d76b0d9 ("cx82310_eth: re-enable ethernet mode after router reboot")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605247627-15385-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update cxgb4 and cxgb3 driver maintainer
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Link: https://lore.kernel.org/r/20201116104322.3959-1-rajur@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A user reports (slightly shortened from the original message):
libphy: lantiq,xrx200-mdio: probed
mdio_bus 1e108000.switch-mii: MDIO device at address 17 is missing.
gswip 1e108000.switch lan: no phy at 2
gswip 1e108000.switch lan: failed to connect to port 2: -19
lantiq,xrx200-net 1e10b308.eth eth0: error -19 setting up slave phy
This is a single-port board using the internal Fast Ethernet PHY. The
user reports that switching to PHY scanning instead of configuring the
PHY within device-tree works around this issue.
The documentation for the standalone variant of the PHY11G (which is
probably very similar to what is used inside the xRX200 SoCs but having
the firmware burnt onto that standalone chip in the factory) states that
the PHY needs 300ms to be ready for MDIO communication after releasing
the reset.
Add a 300ms delay after initializing all GPHYs to ensure that the GPHY
firmware had enough time to initialize and to appear on the MDIO bus.
Unfortunately there is no (known) documentation on what the minimum time
to wait after releasing the reset on an internal PHY so play safe and
take the one for the external variant. Only wait after the last GPHY
firmware is loaded to not slow down the initialization too much (
xRX200 has two GPHYs but newer SoCs have at least three GPHYs).
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201115165757.552641-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Martin Schiller is an active developer and reviewer for the X.25 code.
His company is providing products based on the Linux X.25 stack.
So he is a good candidate for maintainers of the X.25 code.
The original maintainer of the X.25 network layer (Andrew Hendry) has
not sent any email to the netdev mail list since 2013. So he is probably
inactive now.
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20201114111029.326972-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Packets are processed even though the first fragment don't include all
headers through the upper layer header. This breaks TAHI IPv6 Core
Conformance Test v6LC.1.3.6.
Referring to RFC8200 SECTION 4.5: "If the first fragment does not include
all headers through an Upper-Layer header, then that fragment should be
discarded and an ICMP Parameter Problem, Code 3, message should be sent to
the source of the fragment, with the Pointer field set to zero."
The fragment needs to be validated the same way it is done in
commit 2efdaaaf883a ("IPv6: reply ICMP error if the first fragment don't
include all headers") for ipv6. Wrap the validation into a common function,
ipv6_frag_thdr_truncated() to check for truncation in the upper layer
header. This validation does not fullfill all aspects of RFC 8200,
section 4.5, but is at the moment sufficient to pass mentioned TAHI test.
In netfilter, utilize the fragment offset returned by find_prev_fhdr() to
let ipv6_frag_thdr_truncated() start it's traverse from the fragment
header.
Return 0 to drop the fragment in the netfilter. This is the same behaviour
as used on other protocol errors in this function, e.g. when
nf_ct_frag6_queue() returns -EPROTO. The Fragment will later be picked up
by ipv6_frag_rcv() in reassembly.c. ipv6_frag_rcv() will then send an
appropriate ICMP Parameter Problem message back to the source.
References commit 2efdaaaf883a ("IPv6: reply ICMP error if the first
fragment don't include all headers")
Signed-off-by: Georg Kohmann <geokohma@cisco.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/r/20201111115025.28879-1-geokohma@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Zhang Qilong says:
====================
Fix usage counter leak by adding a general sync ops
In many case, we need to check return value of pm_runtime_get_sync,
but it brings a trouble to the usage counter processing. Many callers
forget to decrease the usage counter when it failed, which could
resulted in reference leak. It has been discussed a lot[0][1]. So we
add a function to deal with the usage counter for better coding and
view. Then, we replace pm_runtime_resume_and_get with it in fec_main.c
to avoid it.
[0] https://lkml.org/lkml/2020/6/14/88
[1] https://patchwork.ozlabs.org/project/linux-tegra/list/?series=178139
====================
Link: https://lore.kernel.org/r/20201110092933.3342784-1-zhangqilong3@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
pm_runtime_get_sync() will increment pm usage at first and it will
resume the device later. If runtime of the device has error or
device is in inaccessible state(or other error state), resume
operation will fail. If we do not call put operation to decrease
the reference, it will result in reference count leak. Moreover,
this device cannot enter the idle state and always stay busy or other
non-idle state later. So we fixed it by replacing it with
pm_runtime_resume_and_get.
Fixes: 8fff755e9f8d0 ("net: fec: Ensure clocks are enabled while using mdio bus")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In many case, we need to check return value of pm_runtime_get_sync, but
it brings a trouble to the usage counter processing. Many callers forget
to decrease the usage counter when it failed, which could resulted in
reference leak. It has been discussed a lot[0][1]. So we add a function
to deal with the usage counter for better coding.
[0]https://lkml.org/lkml/2020/6/14/88
[1]https://patchwork.ozlabs.org/project/linux-tegra/list/?series=178139
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2020-11-15
Anant Thazhemadam contributed two patches for the AF_CAN that prevent potential
access of uninitialized member in can_rcv() and canfd_rcv().
The next patch is by Alejandro Concepcion Rodriguez and changes can_restart()
to use the correct function to push a skb into the networking stack from
process context.
Zhang Qilong's patch fixes a memory leak in the error path of the ti_hecc's
probe function.
A patch by me fixes mcba_usb_start_xmit() function in the mcba_usb driver, to
first fill the skb and then pass it to can_put_echo_skb().
Colin Ian King's patch fixes a potential integer overflow on shift in the
peak_usb driver.
The next two patches target the flexcan driver, a patch by me adds the missing
"req_bit" to the stop mode property comment (which was broken during net-next
for v5.10). Zhang Qilong's patch fixes the failure handling of
pm_runtime_get_sync().
The next seven patches target the m_can driver including the tcan4x5x spi
driver glue code. Enric Balletbo i Serra's patch for the tcan4x5x Kconfig fix
the REGMAP_SPI dependency handling. A patch by me for the tcan4x5x driver's
probe() function adds missing error handling to for devm_regmap_init(), and in
tcan4x5x_can_remove() the order of deregistration is fixed. Wu Bo's patch for
the m_can driver fixes the state change handling in
m_can_handle_state_change(). Two patches by Dan Murphy first introduce
m_can_class_free_dev() and then make use of it to fix the freeing of the can
device. A patch by Faiz Abbas add a missing shutdown of the CAN controller in
the m_can_stop() function.
* tag 'linux-can-fixes-for-5.10-20201115' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: m_can: m_can_stop(): set device to software init mode before closing
can: m_can: Fix freeing of can device from peripherials
can: m_can: m_can_class_free_dev(): introduce new function
can: m_can: m_can_handle_state_change(): fix state change
can: tcan4x5x: tcan4x5x_can_remove(): fix order of deregistration
can: tcan4x5x: tcan4x5x_can_probe(): add missing error checking for devm_regmap_init()
can: tcan4x5x: replace depends on REGMAP_SPI with depends on SPI
can: flexcan: fix failure handling of pm_runtime_get_sync()
can: flexcan: flexcan_setup_stop_mode(): add missing "req_bit" to stop mode property comment
can: peak_usb: fix potential integer overflow on shift of a int
can: mcba_usb: mcba_usb_start_xmit(): first fill skb, then pass to can_put_echo_skb()
can: ti_hecc: Fix memleak in ti_hecc_probe
can: dev: can_restart(): post buffer from the right context
can: af_can: prevent potential access of uninitialized member in canfd_rcv()
can: af_can: prevent potential access of uninitialized member in can_rcv()
====================
Link: https://lore.kernel.org/r/20201115174131.2089251-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There might be some requests pending in the buffer when the interface close
sequence occurs. In some devices, these pending requests might lead to the
module not shutting down properly when m_can_clk_stop() is called.
Therefore, move the device to init state before potentially powering it down.
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200825055442.16994-1-faiz_abbas@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fix leaking netdev device from peripherial devices. The call to allocate the
netdev device is made from and managed by the peripherial.
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20200227183829.21854-2-dmurphy@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch creates a common function that peripherials can call to free the
netdev device when failures occur.
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20200227183829.21854-2-dmurphy@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
m_can_handle_state_change() is called with the new_state as an argument.
In the switch statements for CAN_STATE_ERROR_ACTIVE, the comment and the
following code indicate that a CAN_STATE_ERROR_WARNING is handled.
This patch fixes this problem by changing the case to CAN_STATE_ERROR_WARNING.
Signed-off-by: Wu Bo <wubo.oduw@gmail.com>
Link: http://lore.kernel.org/r/20200129022330.21248-2-wubo.oduw@gmail.com
Cc: Dan Murphy <dmurphy@ti.com>
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Change the order in tcan4x5x_can_remove() to be the exact inverse of
tcan4x5x_can_probe(). First m_can_class_unregister(), then power down the
device.
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20201019154233.1262589-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
devm_regmap_init()
This patch adds the missing error checking when initializing the regmap
interface fails.
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20201019154233.1262589-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
regmap is a library function that gets selected by drivers that need it. No
driver modules should depend on it. Instead depends on SPI and select
REGMAP_SPI. Depending on REGMAP_SPI makes this driver only build if another
driver already selected REGMAP_SPI, as the symbol can't be selected through the
menu kernel configuration.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: http://lore.kernel.org/r/20200413141013.506613-1-enric.balletbo@collabora.com
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
pm_runtime_get_sync() will increment pm usage at first and it will resume the
device later. If runtime of the device has error or device is in inaccessible
state(or other error state), resume operation will fail. If we do not call put
operation to decrease the reference, it will result in reference leak in the
two functions flexcan_get_berr_counter() and flexcan_open().
Moreover, this device cannot enter the idle state and always stay busy or other
non-idle state later. So we should fix it through adding
pm_runtime_put_noidle().
Fixes: ca10989632d88 ("can: flexcan: implement can Runtime PM")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201108083000.2599705-1-zhangqilong3@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
property comment
In the patch
d9b081e3fc4b ("can: flexcan: remove ack_grp and ack_bit handling from driver")
the unused ack_grp and ack_bit were removed from the driver. However in the
comment, the "req_bit" was accidentally removed, too.
This patch adds back the "req_bit" bit.
Fixes: d9b081e3fc4b ("can: flexcan: remove ack_grp and ack_bit handling from driver")
Reported-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: http://lore.kernel.org/r/20201014114810.2911135-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The left shift of int 32 bit integer constant 1 is evaluated using 32 bit
arithmetic and then assigned to a signed 64 bit variable. In the case where
time_ref->adapter->ts_used_bits is 32 or more this can lead to an oveflow.
Avoid this by shifting using the BIT_ULL macro instead.
Fixes: bb4785551f64 ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201105112427.40688-1-colin.king@canonical.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
can_put_echo_skb()
The driver has to first fill the skb with data and then handle it to
can_put_echo_skb(). This patch moves the can_put_echo_skb() down, right before
sending the skb out via USB.
Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Link: https://lore.kernel.org/r/20201111221204.1639007-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In the error handling, we should goto the probe_exit_candev
to free ndev to prevent memory leak.
Fixes: dabf54dd1c63 ("can: ti_hecc: Convert TI HECC driver to DT only driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201114111708.3465543-1-zhangqilong3@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
netif_rx() is meant to be called from interrupt contexts. can_restart() may be
called by can_restart_work(), which is called from a worqueue, so it may run in
process context. Use netif_rx_ni() instead.
Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface")
Co-developed-by: Loris Fauster <loris.fauster@ttcontrol.com>
Signed-off-by: Loris Fauster <loris.fauster@ttcontrol.com>
Signed-off-by: Alejandro Concepcion Rodriguez <alejandro@acoro.eu>
Link: https://lore.kernel.org/r/4e84162b-fb31-3a73-fa9a-9438b4bd5234@acoro.eu
[mkl: use netif_rx_ni() instead of netif_rx_any_context()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In canfd_rcv(), cfd->len is uninitialized when skb->len = 0, and this
uninitialized cfd->len is accessed nonetheless by pr_warn_once().
Fix this uninitialized variable access by checking cfd->len's validity
condition (cfd->len > CANFD_MAX_DLEN) separately after the skb->len's
condition is checked, and appropriately modify the log messages that
are generated as well.
In case either of the required conditions fail, the skb is freed and
NET_RX_DROP is returned, same as before.
Fixes: d4689846881d ("can: af_can: canfd_rcv(): replace WARN_ONCE by pr_warn_once")
Reported-by: syzbot+9bcb0c9409066696d3aa@syzkaller.appspotmail.com
Tested-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20201103213906.24219-3-anant.thazhemadam@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In can_rcv(), cfd->len is uninitialized when skb->len = 0, and this
uninitialized cfd->len is accessed nonetheless by pr_warn_once().
Fix this uninitialized variable access by checking cfd->len's validity
condition (cfd->len > CAN_MAX_DLEN) separately after the skb->len's
condition is checked, and appropriately modify the log messages that
are generated as well.
In case either of the required conditions fail, the skb is freed and
NET_RX_DROP is returned, same as before.
Fixes: 8cb68751c115 ("can: af_can: can_rcv(): replace WARN_ONCE by pr_warn_once")
Reported-by: syzbot+9bcb0c9409066696d3aa@syzkaller.appspotmail.com
Tested-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20201103213906.24219-2-anant.thazhemadam@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If sb_occ_port_pool_get() failed in devlink_nl_sb_port_pool_fill(),
msg should be canceled by genlmsg_cancel().
Fixes: df38dafd2559 ("devlink: implement shared buffer occupancy monitoring interface")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Link: https://lore.kernel.org/r/20201113111622.11040-1-wanghai38@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the phy enables power saving technology, the dwmac's software reset
needs more time to complete, enlarge dma reset timeout to 200000us.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20201113090902.5c7aab1a@xhacker.debian
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
