Age | Commit message (Collapse) | Author | Files | Lines |
|
Currently vmid is decided internally inside dc. With the introduction
of new asics we are required to coordinate vmid use with external
components.
This change converts vmid logic to a DAL module allowing vmid to be
passed in as a parameter to DC.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
dcn2 use fixed clocks and not program DPP CLK or Disp_CLK.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
for future use
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
value commited to by HW team is going to be higher
than pre-silicon, and will cause underflow if driver not
updated
[how]
update hardcoded value, update pstate switching logic
to fix case where with long uclk time we won't allow switch
even when we should
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
To prepare for the upcoming DRM plane color management properties
we need to correct a lot of wrong behavior and assumptions made for
CRTC color management.
The documentation added by this commit in amdgpu_dm_color explains
how the HW color pipeline works and its limitations with the DRM
interface.
The current implementation does the following wrong:
- Implicit sRGB DGM when no CRTC DGM is set
- Implicit sRGB RGM when no CRTC RGM is set
- No way to specify a non-linear DGM matrix that produces correct output
- No way to specify a correct RGM when a linear DGM is used
We had workarounds for passing kms_color tests but not all of the
behavior we had wrong was covered by these tests (especially when
it comes to non-linear DGM). Testing both DGM and RGM at the same time
isn't something kms_color tests well either.
[How]
The specifics for how color management works in AMDGPU and the new
behavior can be found by reading the documentation added to
amdgpu_dm_color.c from this patch.
All of the incorrect cases from the old implementation have been
addressed for the atomic interface, but there still a few TODOs for
the legacy one.
Note: this does cause regressions for kms_color@pipe-a-ctm-* over HDMI.
The result looks correct from visual inspection but the CRC no longer
matches. For reference, the test was previously doing the following:
linear degamma -> CTM -> sRGB regamma -> RGB to YUV (709) -> ...
Now the test is doing:
linear degamma -> CTM -> linear regamma -> RGB to YUV (709) -> ...
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
This is meant to make it clearer that 0xf is not a valid OPP ID, and
that code making use of OPP IDs should not accept this value.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
expose this function for future use
Implementation of DCN3 DIO Link Encoder including
dpcs register headers.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
add dwb stereo caps and ver for future use
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add Alpha surface type for future use
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Existing behavior has overlapping ranges resulting in path
dependent SMU selection
[how]
Make ranges non-overlapping, resulting in non-path dependent
selection
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
According to the latest specs, the max_target bpp sink
can support is 16 bpp.
[how]
update dsc max_target_bpp to 16
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
required for new checks.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Current policy assumes virtual DPCD peer device as
an individual MST branch device with 1 input and 1 output.
However this is only true for virtual DP-to-DP peer device.
In general there are three types of virtual DP peer devices.
1. Sink peer device with virtual DPCD.
2. Virtual DP-to-DP Peer device with virtual DPCD.
3. Virtual DP-to-HDMI Protocol Converter Peer Device with
Virtual DPCD.
So we should break the assumption and handle all three types.
[how]
DP-to-DP peer device will have virtual DPCD cap upstream.
Sink peer device will have virtual DPCD on the logical port.
Dp to HDMI protocol converter peer device will have virtual DPCD
on its converter port.
For DSC capable Synaptics non VGA port we workaround by enumerating
a virutal DPCD peer device on its upstream
even if it doesn't have one.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
useful for debugging
[how]
plumb a debug option in dc
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Almost every function in DC that works with stream state expects that
the current state on the stream is the one that it should be writing
out. These functions are typically triggered by specifying a particular
stream update - but the actual contents of the stream update itself
are ignored, leaving it to the DM to actually update the stream state
itself.
The problem with doing this in DM is a matter of timing. On Linux
most of this is incorrectly done in atomic check, when we actually want
it to be done during atomic commit tail while access to DC is locked.
To give an example, a commit requesting to modify color management
state for DM could come in, be rejected, but still have modified
the actual system state for the stream since it's shared memory. The
next time color management gets programmed it'll use the rejected
color management info - which might not even still be around if it's
a custom transfer function.
So a reasonable place to perform this is within DC itself and this is
the model that's currently in use for surface updates. DC can even
compare the current system state to the incoming surface update to
determine update level, something that can't currnetly be done with the
framework for stream updates.
[How]
Duplicate the framework used for surface updates for stream updates
as well. Copy all the updates after checking the update type.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
SwathWidthCThisState is expected to be an unsigned int array.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
when resetting pipes from 480p to dual-pipe 8k, modulo reg write for
video optimized rate updated one pipe without changing the other, causing
sync error
[how]
removed code from dcn2
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The output_bpp pipe parameter was assigned an incorrect value
(color depth enum), and subsequently used to overwrite
the OutputBpp parameter calculated by DML. Seems like this had no
effect except with DSC enabled, which would make DML produce
bad outputs.
[How]
Removed assignment to OutputBpp, fixed output_bpp assignment,
and properly set ForcedOutputLinkBPP instead of OutputBpp.
Also removed condition in DML that prevented forcing of
Output BPP with DSC enabled.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
VM implemenation is missing conversion from HW values in hubbub
DM not passing actual PTB during flip
[how]
add proper HW conversion from logical values
fix cases where we programmed VA even though we are in PA
plumb in PTB from DM
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes for the following:
- Incorrect pointer type (unsigned int instead of double)
- Incorrect DSC number of slices setting
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Currently DSC power gating is disabled by default because the power
transition doesn't happen, causing a crash on some systems
[how]
Fix the lack of power state transition and enable DSC power gating
by default.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Should do full update when display writeback is updated.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Duke Du <Duke.Du@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
dsc adjustment is allowed via stream update sequence.
dsc enablement is only allowed via commit stream sequence.
with the current unified dsc set function, it is hard
to determine which sequence it is called by.
The solution is to decouple dsc adjustment out of enablement
sequence so we can handle them separately.
[how]
decouple dsc adjustment out of enablement.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
current DML logic uses currently trained setting for number
of dp lanes in DML calculations. this is obviously flawed since
just because 1 lane is in use doesn't mean only 1 lane can be used
this causes mode validation to fail depending on current state,
which is incorrect
[how]
DML should always assume 4 lanes are available. validation of
bandwidth is not supposed to be handled by DML, since we do
link validation without DML already
also, DML is expecting there to be a copy of the max state, this
state is removed when update_bounding_box is called to update
actual SKU clocks. fix this as well by duping last state.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Eric Yang <eric.yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
DCN code should make as few references to DCE as possible
[HOW]
Copy DCE110 implementation of find_first_free_match_stream_enc_for_link
into DCN10
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
From DCE110 onward, we have the ability to assign DIG BE and FE
separately for any display connector type; before, we could only do this
for DP.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
With DSC power gating enabled, one of the register reads times out occasionally,
causing a DSC test to fail.
[how]
Disable DSC power gating in Diags.
NOTE: This has to be reverted once the problems with DSC power gating are
resolved.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
We want a test pattern to show up on screen when we're blanked and have
visual confirm enabled, for debugging. Raven does this, it's a mistake that
Navi does not.
[How]
- in "blank_pixel_data", set appropriate DPG pattern for visual confirm
- refactor DPG calls out of "enable_stream_timing"
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
* add plane state null checks
* add and set update surface flags
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
these enums/structs will be used more generically in the future
so moving it to dc_hw_types and dc_types
Signed-off-by: Tyler DiBattista <tyler.dibattista@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Reuse existent code path (dcn1+) and in order to do that apply de gamma
in 1D blender LUT and re use MPC OGAM.
Follow up is required.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
Features that are desirable for minimizing the Global Sync Period:
DRR and lateflip
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
In compute dsc bandwidth range there is an uninitialized variable
[how]
Initialize the variable to the correct value.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
To send sdp message immediately from a single slot.
[How]
Modify the generic SDP message interface, and use GSP4 to send immediate
sdp message.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
DCN2.0 LB BPP should be 48 or 16BPC and max cursor width should be 256.
Also use populate_dml_pipes as functions pointer instead of using it directly
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
A regression was introduced when we set correct tile size
for the gfx9 swizzle mode. This resulted in incorrect
macro tile size.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Plane disable gets calls when we enable blank. On DCN2, we blank by using
DPG to display a black colour instead of using OTG blank. DPG runs off the
OPP clock, therefore we shouldn't disable the OPP clock when disabling the
plane. We do need to disable the OPP clock when disabling the entire pipe,
that will be addressed in a separate commit.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It looks like mpo isn't properly disabled during odm, this change is
meant to fix that.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
dwb fixes.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Duke Du <Duke.Du@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
dcn20 has num_dwb =1 in the res cap, but not created.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Duke Du <Duke.Du@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
GSL is being used to synchronize pipes when vsync is off but
on transition to vsync on during a mode change GSL is not
being reset correctly.
[How]
Disable GSL on any plane that is disabled.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
A few of the new DSC DPCD caps were introduced by a DP 1.4a SCR in order
to give DSC branch decoders a chance to expose their maximum throughput
and maximum line width limitations.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
If a set is done, DSC settings are zeroed out, leading to no DSC for the modes
that require ODM, such as 8k60.
This was a regression introduced by 5a4f26295176bbfc776c75aaf0f6dd8ccf806958.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Gamut map lib provides a wider gamut mapping options
vs BT2390
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Emulating passive dongle on USB-C port causes issue on some asics.
[How]
Check for DP_IS_USB_C flag in bios parser and propagate it to
encoder features flags. If DP_IS_USB_C flag is set and it is trying to
emulate passive dongle, then return fail.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The DCHub arbiter has a mechanism to dynamically rate limit the DCHub
request stream to the fabric. If the memory controller is fully utilized
and the DCHub requestors are well ahead of their amortized schedule,
then it is safe to prevent the next winner from being committed and sent
to the fabric. The utilization of the memory controller is approximated
by ensuring that the number of outstanding requests is greater than a
threshold specified by the ARB_MIN_REQ_OUTSTANDING. To determine that
the DCHub requestors are well ahead of the amortized schedule, the slack
of the next winner is compared with the ARB_SAT_LEVEL in DLG RefClk
cycles.
[How]
The recommended settings to enable thise dynamic limiting for Navi is
180 requests.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
It was missing, although defined in DP spec
[how]
- Add handling of this value to DSC code
- Also remove unused file dsc_helpers.c
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
This is for DC_I2c arbitration use between HW use/SW use and DMCU use.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
calculations
[why]
'Divide by zero' error happens when line size happens to be zero.
[how]
The code that makes sure line size minimum value can be 1 was already
present in DCN1 part of the driver, this is mearly a port to DCN2.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|