summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2020-08-12i2c: iproc: fix race between client unreg and isrDhananjay Phadke1-1/+12
When i2c client unregisters, synchronize irq before setting iproc_i2c->slave to NULL. (1) disable_irq() (2) Mask event enable bits in control reg (3) Erase slave address (avoid further writes to rx fifo) (4) Flush tx and rx FIFOs (5) Clear pending event (interrupt) bits in status reg (6) enable_irq() (7) Set client pointer to NULL Unable to handle kernel NULL pointer dereference at virtual address 0000000000000318 [ 371.020421] pc : bcm_iproc_i2c_isr+0x530/0x11f0 [ 371.025098] lr : __handle_irq_event_percpu+0x6c/0x170 [ 371.030309] sp : ffff800010003e40 [ 371.033727] x29: ffff800010003e40 x28: 0000000000000060 [ 371.039206] x27: ffff800010ca9de0 x26: ffff800010f895df [ 371.044686] x25: ffff800010f18888 x24: ffff0008f7ff3600 [ 371.050165] x23: 0000000000000003 x22: 0000000001600000 [ 371.055645] x21: ffff800010f18888 x20: 0000000001600000 [ 371.061124] x19: ffff0008f726f080 x18: 0000000000000000 [ 371.066603] x17: 0000000000000000 x16: 0000000000000000 [ 371.072082] x15: 0000000000000000 x14: 0000000000000000 [ 371.077561] x13: 0000000000000000 x12: 0000000000000001 [ 371.083040] x11: 0000000000000000 x10: 0000000000000040 [ 371.088519] x9 : ffff800010f317c8 x8 : ffff800010f317c0 [ 371.093999] x7 : ffff0008f805b3b0 x6 : 0000000000000000 [ 371.099478] x5 : ffff0008f7ff36a4 x4 : ffff8008ee43d000 [ 371.104957] x3 : 0000000000000000 x2 : ffff8000107d64c0 [ 371.110436] x1 : 00000000c00000af x0 : 0000000000000000 [ 371.115916] Call trace: [ 371.118439] bcm_iproc_i2c_isr+0x530/0x11f0 [ 371.122754] __handle_irq_event_percpu+0x6c/0x170 [ 371.127606] handle_irq_event_percpu+0x34/0x88 [ 371.132189] handle_irq_event+0x40/0x120 [ 371.136234] handle_fasteoi_irq+0xcc/0x1a0 [ 371.140459] generic_handle_irq+0x24/0x38 [ 371.144594] __handle_domain_irq+0x60/0xb8 [ 371.148820] gic_handle_irq+0xc0/0x158 [ 371.152687] el1_irq+0xb8/0x140 [ 371.155927] arch_cpu_idle+0x10/0x18 [ 371.159615] do_idle+0x204/0x290 [ 371.162943] cpu_startup_entry+0x24/0x60 [ 371.166990] rest_init+0xb0/0xbc [ 371.170322] arch_call_rest_init+0xc/0x14 [ 371.174458] start_kernel+0x404/0x430 Fixes: c245d94ed106 ("i2c: iproc: Add multi byte read-write support for slave mode") Signed-off-by: Dhananjay Phadke <dphadke@linux.microsoft.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-10i2c: eg20t: use generic power managementVaibhav Gupta1-29/+7
Drivers using legacy power management .suspen()/.resume() callbacks have to manage PCI states and device's PM states themselves. They also need to take care of standard configuration registers. Switch to generic power management framework using a single "struct dev_pm_ops" variable to take the unnecessary load from the driver. This also avoids the need for the driver to directly call most of the PCI helper functions and device power state control functions, as through the generic framework PCI Core takes care of the necessary operations, and drivers are required to do only device-specific jobs. Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-10i2c: eg20t: Drop PCI wakeup calls from .suspend/.resumeVaibhav Gupta1-3/+0
The driver calls pci_enable_wake(...., false) in pch_i2c_suspend() as well as pch_i2c_resume(). Either it should enable-wake the device in .suspend() or should not invoke pci_enable_wake() at all. Concluding that this driver doesn't support enable-wake and PCI core calls pci_enable_wake(pci_dev, PCI_D0, false) during resume, drop it from .suspend() and .resume(). Reported-by: Bjorn Helgaas <helgaas@kernel.org> Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-10i2c: mediatek: Fix i2c_spec_values descriptionMatthias Brugger1-5/+4
The struct i2c_spec_values have it's members documented but is missing the starting '@', which leads to warings like: drivers/i2c/busses/i2c-mt65xx.c:267: warning: Function parameter or member 'min_low_ns' not described in 'i2c_spec_values' We also delete min_high_ns member as it is not used in the code. Signed-off-by: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: mediatek: Add i2c compatible for MediaTek MT8192Qii Wang1-0/+15
Add i2c compatible for MT8192. Compare to MT8183 i2c controller, MT8192 support more then 8GB DMA mode. Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05dt-bindings: i2c: update bindings for MT8192 SoCQii Wang1-0/+1
Add a DT binding documentation for the MT8192 soc. Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: mediatek: Add access to more than 8GB dram in i2c driverQii Wang1-22/+17
Newer MTK chip support more than 8GB of dram. Replace support_33bits with more general dma_max_support and remove mtk_i2c_set_4g_mode. Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com> Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: mediatek: Add apdma sync in i2c driverQii Wang1-3/+20
With the apdma remove hand-shake signal, it need to keep i2c and apdma in sync manually. Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: i801: Add support for Intel Tiger Lake PCH-HJarkko Nikula1-0/+4
Add SMBus PCI ID on Intel Tiger Lake PCH-H. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: i801: Add support for Intel Emmitsburg PCHMika Westerberg3-0/+6
Add support for SMBus controller on Intel Emmitsburg PCH. This is the same IP as used in Cannon Lake and derivatives. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: bcm2835: Replace HTTP links with HTTPS onesAlexander A. Klimov1-1/+1
Rationale: Reduces attack surface on kernel devs opening the links for MITM as HTTPS traffic is much harder to manipulate. Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de> [wsa: shortened commit message] Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05Documentation: i2c: dev: 'block process call' is supportedWolfram Sang1-0/+2
And it has been for a while (since 2012 at least), only it was not documented. Add it. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: at91: Move to generic GPIO bus recoveryCodrin Ciubotariu2-69/+3
Make the Microchip at91 driver the first to use the generic GPIO bus recovery support from the I2C core and discard the driver implementation. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: core: treat EPROBE_DEFER when acquiring SCL/SDA GPIOsCodrin Ciubotariu1-12/+14
Even if I2C bus GPIO recovery is optional, devm_gpiod_get() can return -EPROBE_DEFER, so we should at least treat that. This ends up with i2c_register_adapter() to be able to return -EPROBE_DEFER. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: core: add generic I2C GPIO recoveryCodrin Ciubotariu2-0/+137
Multiple I2C bus drivers use similar bindings to obtain information needed for I2C recovery. For example, for platforms using device-tree, the properties look something like this: &i2c { ... pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c_default>; pinctrl-1 = <&pinctrl_i2c_gpio>; sda-gpios = <&pio 0 GPIO_ACTIVE_HIGH>; scl-gpios = <&pio 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; ... } For this reason, we can add this common initialization in the core. This way, other I2C bus drivers will be able to support GPIO recovery just by providing a pointer to platform's pinctrl and calling i2c_recover_bus() when SDA is stuck low. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> [wsa: inverted one logic for better readability, minor update to kdoc] Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05dt-bindings: i2c: add generic properties for GPIO bus recoveryCodrin Ciubotariu1-0/+10
The I2C GPIO bus recovery properties consist of two GPIOS and one extra pinctrl state ("gpio" or "recovery"). "recovery" pinctrl state is considered deprecated and "gpio" should be used instead. Not all are mandatory for recovery. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Reviewed-by: Rob Herring <robh@kernel.org> [wsa: kept sorting, minor whitespace change] Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-31i2c: rcar: avoid race when unregistering slaveWolfram Sang1-3/+5
Due to the lockless design of the driver, it is theoretically possible to access a NULL pointer, if a slave interrupt was running while we were unregistering the slave. To make this rock solid, disable the interrupt for a short time while we are clearing the interrupt_enable register. This patch is purely based on code inspection. The OOPS is super-hard to trigger because clearing SAR (the address) makes interrupts even more unlikely to happen as well. While here, reinit SCR to SDBS because this bit should always be set according to documentation. There is no effect, though, because the interface is disabled. Fixes: 7b814d852af6 ("i2c: rcar: avoid race when unregistering slave client") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-31Merge tag 'v5.8-rc7' into i2c/for-5.9Wolfram Sang1105-6690/+10208
2020-07-28i2c: tegra: Avoid tegra_i2c_init_dma() for Tegra210 vi i2cSowjanya Komatineni1-1/+1
VI I2C is on host1x bus so APB DMA can't be used for Tegra210 VI I2C and there are no tx and rx dma channels for VI I2C. So, avoid attempt of requesting DMA channels. Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: tegra: Fix runtime resume to re-init VI I2CSowjanya Komatineni1-0/+16
VI I2C is on host1x bus and is part of VE power domain. During suspend/resume VE power domain goes through power off/on. So, controller reset followed by i2c re-initialization is required after the domain power up. This patch fixes it. Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: tegra: Fix the error path in tegra_i2c_runtime_resumeSowjanya Komatineni1-3/+8
tegra_i2c_runtime_resume does not disable prior enabled clocks properly. This patch fixes it. Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: tegra: Remove NULL pointer check before ↵Sowjanya Komatineni1-41/+23
clk_enable/disable/prepare/unprepare clk_enable, clk_disable, clk_prepare, and clk_unprepare APIs have implementation for checking clk pointer not NULL and clock consumers can safely call these APIs without NULL pointer check. So, this patch cleans up Tegra i2c driver to remove explicit checks before these APIs. Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: tegra: Don't mark VI I2C as IRQ safe runtime PMSowjanya Komatineni1-1/+9
Tegra VI I2C is part of VE power domain and typically used for camera usecases. VE power domain is not always on and is non-IRQ safe. So, IRQ safe device cannot be attached to a non-IRQ safe domain as it prevents powering off the PM domain and generic power domain driver will warn. Current driver marks all I2C devices as IRQ safe and VI I2C device does not require IRQ safe as it will not be used for atomic transfers. This patch has fix to make VI I2C as non-IRQ safe. Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-27i2c: core: do not use logical device when creating irq domainWolfram Sang1-1/+1
Let's rather use its physical parent device to give proper namings and connections in debugfs. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-26Linux 5.8-rc7v5.8-rc7Linus Torvalds1-1/+1
2020-07-26Merge tag 'kbuild-fixes-v5.8-3' of ↵Linus Torvalds2-4/+12
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild into master Pull Kbuild fixes from Masahiro Yamada: - do not use non-portable strsep() in a host program - fix single target builds for external modules - change Clang's --prefix option to make it work for the latest Clang * tag 'kbuild-fixes-v5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: Makefile: Fix GCC_TOOLCHAIN_DIR prefix for Clang cross compilation kbuild: fix single target builds for external modules modpost: remove use of non-standard strsep() in HOSTCC code
2020-07-26Merge branch 'parisc-5.8-2' of ↵Linus Torvalds3-0/+16
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux into master Pull parisc fixes from Helge Deller: "Two fixes: - Add the cmpxchg() function for pointers to u8 values. This fixes a kernel linking error when building the tusb1210 driver (from Liam Beguin). - Add a define for atomic64_set_release() to fix CPU soft lockups which happen because of missing unlocks while processing bit operations (from John David Anglin)" * 'parisc-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: parisc: Add atomic64_set_release() define to avoid CPU soft lockups parisc: add support for cmpxchg on u8 pointers
2020-07-26Merge tag 'char-misc-5.8-rc7' of ↵Linus Torvalds17-112/+186
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc into master Pull char/misc driver fixes from Greg KH: "Here are a few small driver fixes for 5.8-rc7 They include: - habanalabs fixes - tiny fpga driver fixes - /dev/mem fixup from previous changes - interconnect driver fixes - binder fix All of these have been in linux-next for a while with no reported issues" * tag 'char-misc-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: interconnect: msm8916: Fix buswidth of pcnoc_s nodes interconnect: Do not skip aggregation for disabled paths /dev/mem: Add missing memory barriers for devmem_inode binder: Don't use mmput() from shrinker function. habanalabs: prevent possible out-of-bounds array access fpga: dfl: fix bug in port reset handshake fpga: dfl: pci: reduce the scope of variable 'ret' habanalabs: set 4s timeout for message to device CPU habanalabs: set clock gating per engine habanalabs: block WREG_BULK packet on PDMA
2020-07-26Merge tag 'driver-core-5.8-rc7' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core into master Pull driver core fix from Greg KH: "A single driver core fix for 5.8-rc7. It resolves a problem found in the previous fix for this code made in 5.8-rc6. Hopefully this is all now cleared up, as this seems to be the last of the reported issues in this area, and was tested on the problem hardware. This patch has been in linux-next with no reported problems" * tag 'driver-core-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: device property: Avoid NULL pointer dereference in device_get_next_child_node()
2020-07-26Merge tag 'staging-5.8-rc7' of ↵Linus Torvalds5-19/+63
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging into master Pull staging driver fixes from Greg KH: "Five small staging driver fixes for 5.8-rc7 to resolve some reported problems: - four comedi driver fixes for problems found with them - a syzbot-found fix for the wlang-ng driver that resolves a much reported problem. All of these have been in linux-next with no reported issues" * tag 'staging-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: staging: wlan-ng: properly check endpoint types staging: comedi: addi_apci_1564: check INSN_CONFIG_DIGITAL_TRIG shift staging: comedi: addi_apci_1500: check INSN_CONFIG_DIGITAL_TRIG shift staging: comedi: addi_apci_1032: check INSN_CONFIG_DIGITAL_TRIG shift staging: comedi: ni_6527: fix INSN_CONFIG_DIGITAL_TRIG support
2020-07-26Merge tag 'tty-5.8-rc7' of ↵Linus Torvalds10-32/+69
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty into master Pull tty/serial/fbcon fixes from Greg KH: "Here are some small tty and serial and fbcon fixes for 5.8-rc7 to resolve some reported issues. The fbcon fix is in here as it was simpler to take it this way (and it was acked by the maintainer) as it was related to the vt console fix as well, both of which resolve syzbot-found issues in the console handling code. The other serial driver fixes are for small issues reported in the -rc releases. All of these have been in linux-next with no reported issues" * tag 'tty-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: serial: exar: Fix GPIO configuration for Sealevel cards based on XR17V35X fbdev: Detect integer underflow at "struct fbcon_ops"->clear_margins. serial: 8250_mtk: Fix high-speed baud rates clamping serial: 8250: fix null-ptr-deref in serial8250_start_tx() serial: tegra: drop bogus NULL tty-port checks serial: tegra: fix CREAD handling for PIO tty: xilinx_uartps: Really fix id assignment vt: Reject zero-sized screen buffer size.
2020-07-26Merge tag 'usb-5.8-rc7' of ↵Linus Torvalds3-1/+8
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb into master Pull USB fixes from Greg KH: "Three small USB XHCI driver fixes for 5.8-rc7. They all resolve some minor issues that have been reported on some different platforms. All of these have been in linux-next with no reported issues" * tag 'usb-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: usb: tegra: Fix allocation for the FPCI context usb: xhci: Fix ASM2142/ASM3142 DMA addressing usb: xhci-mtk: fix the failure of bandwidth allocation
2020-07-26Merge tag 'scsi-fixes' of ↵Linus Torvalds1-5/+11
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi into master Pull SCSI fix from James Bottomley: "Small core patch to fix a corner case bug: we forgot to run the queues to handle starvation in the error exit from the scsi_queue_rq routine, which can lead to hangs on error conditions" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: core: Run queue in case of I/O resource contention failure
2020-07-26dt-bindings: i2c: renesas,iic: Document r8a774e1 supportLad Prabhakar1-0/+1
Document IIC controller for RZ/G2H (R8A774E1) SoC, which is compatible with R-Car Gen3 SoC family. Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-26dt-bindings: i2c: renesas,i2c: Document r8a774e1 supportLad Prabhakar1-0/+1
Document i2c controller for RZ/G2H (R8A774E1) SoC, which is compatible with R-Car Gen3 SoC family. Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-26i2c: rcar: slave: only send STOP event when we have been addressedWolfram Sang1-3/+4
When the SSR interrupt is activated, it will detect every STOP condition on the bus, not only the ones after we have been addressed. So, enable this interrupt only after we have been addressed, and disable it otherwise. Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-25Merge tag 'riscv-for-linus-5.8-rc7' of ↵Linus Torvalds2-23/+47
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux into master Pull RISC-V fixes from Palmer Dabbelt: "A few more fixes this week: - A fix to avoid using SBI calls during kasan initialization, as the SBI calls themselves have not been probed yet. - Three fixes related to systems with multiple memory regions" * tag 'riscv-for-linus-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: riscv: Parse all memory blocks to remove unusable memory RISC-V: Do not rely on initrd_start/end computed during early dt parsing RISC-V: Set maximum number of mapped pages correctly riscv: kasan: use local_tlb_flush_all() to avoid uninitialized __sbi_rfence
2020-07-25Merge tag 'x86-urgent-2020-07-25' of ↵Linus Torvalds5-18/+28
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master Pull x86 fixes from Ingo Molnar: "Misc fixes: - Fix a section end page alignment assumption that was causing crashes - Fix ORC unwinding on freshly forked tasks which haven't executed yet and which have empty user task stacks - Fix the debug.exception-trace=1 sysctl dumping of user stacks, which was broken by recent maccess changes" * tag 'x86-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/dumpstack: Dump user space code correctly again x86/stacktrace: Fix reliable check for empty user task stacks x86/unwind/orc: Fix ORC for newly forked tasks x86, vmlinux.lds: Page-align end of ..page_aligned sections
2020-07-25Merge tag 'perf-urgent-2020-07-25' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master Pull uprobe fix from Ingo Molnar: "Fix an interaction/regression between uprobes based shared library tracing & GDB" * tag 'perf-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: uprobes: Change handle_swbp() to send SIGTRAP with si_code=SI_KERNEL, to fix GDB regression
2020-07-25Merge tag 'timers-urgent-2020-07-25' of ↵Linus Torvalds2-10/+58
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master Pull timer fix from Ingo Molnar: "Fix a suspend/resume regression (crash) on TI AM3/AM4 SoC's" * tag 'timers-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: clocksource/drivers/timer-ti-dm: Fix suspend and resume for am3 and am4
2020-07-25Merge tag 'sched-urgent-2020-07-25' of ↵Linus Torvalds1-10/+15
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master Pull scheduler fixes from Ingo Molnar: "Fix a race introduced by the recent loadavg race fix, plus add a debug check for a hard to debug case of bogus wakeup function flags" * tag 'sched-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched: Warn if garbage is passed to default_wake_function() sched: Fix race against ptrace_freeze_trace()
2020-07-25Merge tag 'efi-urgent-2020-07-25' of ↵Linus Torvalds12-40/+43
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master Pull EFI fixes from Ingo Molnar: "Various EFI fixes: - Fix the layering violation in the use of the EFI runtime services availability mask in users of the 'efivars' abstraction - Revert build fix for GCC v4.8 which is no longer supported - Clean up some x86 EFI stub details, some of which are borderline bugs that copy around garbage into padding fields - let's fix these out of caution. - Fix build issues while working on RISC-V support - Avoid --whole-archive when linking the stub on arm64" * tag 'efi-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: efi: Revert "efi/x86: Fix build with gcc 4" efi/efivars: Expose RT service availability via efivars abstraction efi/libstub: Move the function prototypes to header file efi/libstub: Fix gcc error around __umoddi3 for 32 bit builds efi/libstub/arm64: link stub lib.a conditionally efi/x86: Only copy upto the end of setup_header efi/x86: Remove unused variables
2020-07-25Merge tag '5.8-rc6-cifs-fix' of git://git.samba.org/sfrench/cifs-2.6 into masterLinus Torvalds1-8/+2
Pull cifs fix from Steve French: "A fix for a recently discovered regression in rename to older servers caused by a recent patch" * tag '5.8-rc6-cifs-fix' of git://git.samba.org/sfrench/cifs-2.6: Revert "cifs: Fix the target file was deleted when rename failed."
2020-07-25Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net into masterLinus Torvalds127-676/+1022
Pull networking fixes from David Miller: 1) Fix RCU locaking in iwlwifi, from Johannes Berg. 2) mt76 can access uninitialized NAPI struct, from Felix Fietkau. 3) Fix race in updating pause settings in bnxt_en, from Vasundhara Volam. 4) Propagate error return properly during unbind failures in ax88172a, from George Kennedy. 5) Fix memleak in adf7242_probe, from Liu Jian. 6) smc_drv_probe() can leak, from Wang Hai. 7) Don't muck with the carrier state if register_netdevice() fails in the bonding driver, from Taehee Yoo. 8) Fix memleak in dpaa_eth_probe, from Liu Jian. 9) Need to check skb_put_padto() return value in hsr_fill_tag(), from Murali Karicheri. 10) Don't lose ionic RSS hash settings across FW update, from Shannon Nelson. 11) Fix clobbered SKB control block in act_ct, from Wen Xu. 12) Missing newlink in "tx_timeout" sysfs output, from Xiongfeng Wang. 13) IS_UDPLITE cleanup a long time ago, incorrectly handled transformations involving UDPLITE_RECV_CC. From Miaohe Lin. 14) Unbalanced locking in netdevsim, from Taehee Yoo. 15) Suppress false-positive error messages in qed driver, from Alexander Lobakin. 16) Out of bounds read in ax25_connect and ax25_sendmsg, from Peilin Ye. 17) Missing SKB release in cxgb4's uld_send(), from Navid Emamdoost. 18) Uninitialized value in geneve_changelink(), from Cong Wang. 19) Fix deadlock in xen-netfront, from Andera Righi. 19) flush_backlog() frees skbs with IRQs disabled, so should use dev_kfree_skb_irq() instead of kfree_skb(). From Subash Abhinov Kasiviswanathan. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits) drivers/net/wan: lapb: Corrected the usage of skb_cow dev: Defer free of skbs in flush_backlog qrtr: orphan socket in qrtr_release() xen-netfront: fix potential deadlock in xennet_remove() flow_offload: Move rhashtable inclusion to the source file geneve: fix an uninitialized value in geneve_changelink() bonding: check return value of register_netdevice() in bond_newlink() tcp: allow at most one TLP probe per flight AX.25: Prevent integer overflows in connect and sendmsg cxgb4: add missing release on skb in uld_send() net: atlantic: fix PTP on AQC10X AX.25: Prevent out-of-bounds read in ax25_sendmsg() sctp: shrink stream outq when fails to do addstream reconf sctp: shrink stream outq only when new outcnt < old outcnt AX.25: Fix out-of-bounds read in ax25_connect() enetc: Remove the mdio bus on PF probe bailout net: ethernet: ti: add NETIF_F_HW_TC hw feature flag for taprio offload net: ethernet: ave: Fix error returns in ave_init drivers/net/wan/x25_asy: Fix to make it work ipvs: fix the connection sync failed in some cases ...
2020-07-24riscv: Parse all memory blocks to remove unusable memoryAtish Patra1-14/+17
Currently, maximum physical memory allowed is equal to -PAGE_OFFSET. That's why we remove any memory blocks spanning beyond that size. However, it is done only for memblock containing linux kernel which will not work if there are multiple memblocks. Process all memory blocks to figure out how much memory needs to be removed and remove at the end instead of updating the memblock list in place. Signed-off-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2020-07-24RISC-V: Do not rely on initrd_start/end computed during early dt parsingAtish Patra1-6/+27
Currently, initrd_start/end are computed during early_init_dt_scan but used during arch_setup. We will get the following panic if initrd is used and CONFIG_DEBUG_VIRTUAL is turned on. [ 0.000000] ------------[ cut here ]------------ [ 0.000000] kernel BUG at arch/riscv/mm/physaddr.c:33! [ 0.000000] Kernel BUG [#1] [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 5.8.0-rc4-00015-ged0b226fed02 #886 [ 0.000000] epc: ffffffe0002058d2 ra : ffffffe0000053f0 sp : ffffffe001001f40 [ 0.000000] gp : ffffffe00106e250 tp : ffffffe001009d40 t0 : ffffffe00107ee28 [ 0.000000] t1 : 0000000000000000 t2 : ffffffe000a2e880 s0 : ffffffe001001f50 [ 0.000000] s1 : ffffffe0001383e8 a0 : ffffffe00c087e00 a1 : 0000000080200000 [ 0.000000] a2 : 00000000010bf000 a3 : ffffffe00106f3c8 a4 : ffffffe0010bf000 [ 0.000000] a5 : ffffffe000000000 a6 : 0000000000000006 a7 : 0000000000000001 [ 0.000000] s2 : ffffffe00106f068 s3 : ffffffe00106f070 s4 : 0000000080200000 [ 0.000000] s5 : 0000000082200000 s6 : 0000000000000000 s7 : 0000000000000000 [ 0.000000] s8 : 0000000080011010 s9 : 0000000080012700 s10: 0000000000000000 [ 0.000000] s11: 0000000000000000 t3 : 000000000001fe30 t4 : 000000000001fe30 [ 0.000000] t5 : 0000000000000000 t6 : ffffffe00107c471 [ 0.000000] status: 0000000000000100 badaddr: 0000000000000000 cause: 0000000000000003 [ 0.000000] random: get_random_bytes called from print_oops_end_marker+0x22/0x46 with crng_init=0 To avoid the error, initrd_start/end can be computed from phys_initrd_start/size in setup itself. It also improves the initrd placement by aligning the start and size with the page size. Fixes: 76d2a0493a17 ("RISC-V: Init and Halt Code") Signed-off-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2020-07-24drivers/net/wan: lapb: Corrected the usage of skb_cowXie He2-4/+8
This patch fixed 2 issues with the usage of skb_cow in LAPB drivers "lapbether" and "hdlc_x25": 1) After skb_cow fails, kfree_skb should be called to drop a reference to the skb. But in both drivers, kfree_skb is not called. 2) skb_cow should be called before skb_push so that is can ensure the safety of skb_push. But in "lapbether", it is incorrectly called after skb_push. More details about these 2 issues: 1) The behavior of calling kfree_skb on failure is also the behavior of netif_rx, which is called by this function with "return netif_rx(skb);". So this function should follow this behavior, too. 2) In "lapbether", skb_cow is called after skb_push. This results in 2 logical issues: a) skb_push is not protected by skb_cow; b) An extra headroom of 1 byte is ensured after skb_push. This extra headroom has no use in this function. It also has no use in the upper-layer function that this function passes the skb to (x25_lapb_receive_frame in net/x25/x25_dev.c). So logically skb_cow should instead be called before skb_push. Cc: Eric Dumazet <edumazet@google.com> Cc: Martin Schiller <ms@dev.tdt.de> Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-24dev: Defer free of skbs in flush_backlogSubash Abhinov Kasiviswanathan1-1/+1
IRQs are disabled when freeing skbs in input queue. Use the IRQ safe variant to free skbs here. Fixes: 145dd5f9c88f ("net: flush the softnet backlog in process context") Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-24RISC-V: Set maximum number of mapped pages correctlyAtish Patra1-1/+1
Currently, maximum number of mapper pages are set to the pfn calculated from the memblock size of the memblock containing kernel. This will work until that memblock spans the entire memory. However, it will be set to a wrong value if there are multiple memblocks defined in kernel (e.g. with efi runtime services). Set the the maximum value to the pfn calculated from dram size. Signed-off-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2020-07-24Merge tag 'pci-v5.8-fixes-2' of ↵Linus Torvalds2-23/+11
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into master Pull PCI fixes from Bjorn Helgaas: - Reject invalid IRQ 0 command line argument for virtio_mmio because IRQ 0 now generates warnings (Bjorn Helgaas) - Revert "PCI/PM: Assume ports without DLL Link Active train links in 100 ms", which broke nouveau (Bjorn Helgaas) * tag 'pci-v5.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: Revert "PCI/PM: Assume ports without DLL Link Active train links in 100 ms" virtio-mmio: Reject invalid IRQ 0 command line argument
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-08 22:56:56 +0000