| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
To make sure the clock is fully gated in ->remove(), we first need to
to bring the device into full power by invoking pm_runtime_get_sync().
Then, let's both unprepare and disable the clock.
[mszyprow: rebased onto v4.9-rc4]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
There are no need to set up the PM callbacks (runtime and system) unless
they are being used. It also causes compiler warnings about unused
functions.
Silence the warnings by making them available for CONFIG_PM (runtime
callbacks) and CONFIG_PM_SLEEP (system sleep callbacks).
[mszyprow: squashed two patches into one to avoid potential build
break, changed patch subject and updated commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The driver depended on CONFIG_PM to be functional. Let's remove that
dependency, by enable the runtime PM resourses during ->probe() and
update the device's runtime PM status to reflect this.
[mszyprow: rebased onto v4.9-rc4]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Since gsc_m2m_resume() always returns 0, convert it to a void instead.
[mszyprow: rebased onto v4.9-rc4]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Instead of having separate functions that fetches, prepares and
unprepares the clock, let's encapsulate this code into ->probe().
This makes error handling easier and decreases the lines of code.
[mszyprow: rebased onto v4.9-rc4]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Include buffer size in s5p_mfc_alloc_priv_buf() the error message
when it fails to allocate the buffer.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Media drivers that use the videobuf2 framework have to give back to vb2
all the buffers that received from vb2 using its .buf_queue callback.
But the exynos-gsc driver isn't doing a proper cleanup so vb2 complains
that the number of buffers enqueued and received are not balanced:
WARNING: CPU: 2 PID: 660 at drivers/media/v4l2-core/videobuf2-core.c:1654 __vb2_queue_cancel+0xec/0x150 [videobuf2_core]
Modules linked in: mwifiex_sdio mwifiex uvcvideo exynos_gsc videobuf2_vmalloc s5p_mfc s5p_jpeg
CPU: 2 PID: 660 Comm: lt-gst-validate Not tainted 4.8.0
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c010e24c>] (unwind_backtrace) from [<c010af30>] (show_stack+0x10/0x14)
[<c010af30>] (show_stack) from [<c03291a4>] (dump_stack+0x88/0x9c)
[<c03291a4>] (dump_stack) from [<c011a858>] (__warn+0xe8/0x100)
[<c011a858>] (__warn) from [<c011a920>] (warn_slowpath_null+0x20/0x28)
[<c011a920>] (warn_slowpath_null) from [<bf0b6ed0>] (__vb2_queue_cancel+0xec/0x150 [videobuf2_core])
[<bf0b6ed0>] (__vb2_queue_cancel [videobuf2_core]) from [<bf0b7464>] (vb2_core_streamoff+0x34/0x9c [videobuf2_core])
[<bf0b7464>] (vb2_core_streamoff [videobuf2_core]) from [<bf11b9e8>] (v4l2_m2m_streamoff+0x2c/0xe4 [v4l2_mem2mem])
[<bf11b9e8>] (v4l2_m2m_streamoff [v4l2_mem2mem]) from [<bf01b84c>] (__video_do_ioctl+0x298/0x30c [videodev])
[<bf01b84c>] (__video_do_ioctl [videodev]) from [<bf01b234>] (video_usercopy+0x174/0x4e8 [videodev])
[<bf01b234>] (video_usercopy [videodev]) from [<bf0165c8>] (v4l2_ioctl+0xc4/0xd8 [videodev])
[<bf0165c8>] (v4l2_ioctl [videodev]) from [<c01f291c>] (do_vfs_ioctl+0x9c/0x8f4)
[<c01f291c>] (do_vfs_ioctl) from [<c01f31a8>] (SyS_ioctl+0x34/0x5c)
[<c01f31a8>] (SyS_ioctl) from [<c01078c0>] (ret_fast_syscall+0x0/0x3c)
Fix this by passing back to vb2 all the received buffers that were not
processed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The driver doesn't unregister the video device node when the driver is
removed, this keeps video device nodes that makes the machine to crash
with a NULL pointer dereference when nodes are attempted to be opened:
[ 36.530006] Unable to handle kernel paging request at virtual address bf1f8200
[ 36.535985] pgd = edbbc000
[ 36.538486] [bf1f8200] *pgd=6d99a811, *pte=00000000, *ppte=00000000
[ 36.544727] Internal error: Oops: 7 [#1] PREEMPT SMP ARM
[ 36.550016] Modules linked in: s5p_jpeg s5p_mfc v4l2_mem2mem videobuf2_dma_contig
[ 36.566303] CPU: 6 PID: 533 Comm: v4l2-ctl Not tainted 4.8.0
[ 36.574466] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 36.580526] task: ee3cc600 task.stack: ed626000
[ 36.585046] PC is at try_module_get+0x1c/0xac
[ 36.589364] LR is at try_module_get+0x1c/0xac
[ 36.593698] pc : [<c0187a60>] lr : [<c0187a60>] psr: 80070013
[ 36.593698] sp : ed627de0 ip : a0070013 fp : 00000000
[ 36.605156] r10: 00000002 r9 : ed627ed0 r8 : 00000000
[ 36.610331] r7 : c01e5f14 r6 : ed57be00 r5 : bf1f8200 r4 : bf1f8200
[ 36.616834] r3 : 00000002 r2 : 00000002 r1 : 01930192 r0 : 00000001
..
[ 36.785004] [<c0187a60>] (try_module_get) from [<c01e5c10>] (cdev_get+0x1c/0x4c)
[ 36.792362] [<c01e5c10>] (cdev_get) from [<c01e5f40>] (chrdev_open+0x2c/0x178)
[ 36.799555] [<c01e5f40>] (chrdev_open) from [<c01df5d4>] (do_dentry_open+0x1e0/0x300)
[ 36.807360] [<c01df5d4>] (do_dentry_open) from [<c01eecdc>] (path_openat+0x35c/0xf58)
[ 36.815154] [<c01eecdc>] (path_openat) from [<c01f0668>] (do_filp_open+0x5c/0xc0)
[ 36.822606] [<c01f0668>] (do_filp_open) from [<c01e09ac>] (do_sys_open+0x10c/0x1bc)
[ 36.830235] [<c01e09ac>] (do_sys_open) from [<c01078c0>] (ret_fast_syscall+0x0/0x3c)
[ 36.837942] Code: 0a00001c e1a04000 e3a00001 ebfec92d (e5943000)
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The struct v4l2_device instance for the G-Scaler is not dyanmically
allocated but a member of the struct gsc_dev. In fact, the assigned
.release callback is video_device_release_empty().
But gsc_register_m2m_device() attempts to release the v4l2_device by
calling video_device_release() in its error path. This is wrong since
the v4l2_device wasn't allocated directly and will be freed once its
parent struct gsc_dev is freed.
While being there, rename the remaining goto label in the error path
to something that better explains the error path cleanup.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The driver don't take into account the differences between packed, semi
planar and multi planar formats when calculating the pixel format bytes
per lines and image size values. This makes GStreamer to fail when the
following formats are used NV12, NV21, NV16, NV61, YV12, I420 and Y42B:
"gst_video_frame_map_id: failed to map video frame plane 1"
Nicolas suggested to use the logic found in the Exynos FIMC v4l2 driver
since does this correctly. So this patch changes the bytes per line and
image size calculation according to what's done in this media driver.
After this patch most supported formats work correctly. There are still
issues with the NV21 and NV61 formats, but that seems to be a separate
problem since NV12 and NV16 work and these formats use the same values.
So this can be fixed as a follow-up and shouldn't be a blocker for this
change that improves the driver's support.
Suggested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The driver exposes 32-bit A/XRGB 8-8-8-8 as supported format but testing
shows that using this format produces frames with wrong colors. The test
was done with the following GStreamer pipeline:
$ gst-launch-1.0 videotestsrc num-buffers=20 ! video/x-raw,format=UYVY \
! v4l2video3convert ! video/x-raw,format=xRGB ! videoconvert ! kmssink
The manual seems to state that the Pixel Format are in Little Endianness
so instead use the 32-bit BGRA/X 8-8-8-8 pixel format. This format works
correctly when using the following pipeline:
$ gst-launch-1.0 videotestsrc num-buffers=20 ! video/x-raw,format=UYVY \
! v4l2video3convert ! video/x-raw,format=BGRx ! kmssink
This change is similar to commit 7f2816e51ea1 ("[media] s5p-fimc: Changed
RGB32 to BGR32") that fixed the same issue on a different Samsung driver.
Suggested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
User-space applications can use the VIDIOC_REQBUFS ioctl to determine if a
memory mapped, user pointer or DMABUF based I/O is supported by a driver.
For example, GStreamer attempts to determine the I/O methods supported by
the driver by doing many VIDIOC_REQBUFS ioctl calls with different memory
types and count 0. And then the real VIDIOC_REQBUFS call with count == n
is be made to allocate the buffers. But for count 0, the driver not only
frees the buffers but also clears the format set before with VIDIOC_S_FMT.
This is a problem since STREAMON fails if a format isn't set but GStreamer
first sets a format and then tries to determine the supported I/O methods,
so the format will be cleared on REQBUFS(0), before the call to STREAMON.
To avoid this issue, only free the buffers on VIDIOC_REQBUFS(0) but don't
clear the format. Since is completely valid to set the format and then do
different calls to REQBUFS before a call to STREAMON.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The driver try_fmt handler prints a message each time that the image
size has been changed due the maximum and minimum width and height.
Since user-space can try different format and sizes, this logs a lot
of unnecessary messages. Change the message log level to debug and
while being there, also add a new line to the message.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
s5p_mfc_alloc_priv_buf() prints two message to report invalid memory
configuration error. Collapse them into a single message.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
For tiled format, we need to allocated a multiple of the row size. A
good example is for 1280x720, wich get adjusted to 1280x736. In tiles,
this mean Y plane is 20x23 and UV plane 20x12. Because of the rounding,
the previous code would only have enough space to fit half of the last
row.
[mchehab@s-opensource.com: fix coding style]
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The FDP1 driver performs advanced de-interlacing on a memory 2 memory
based video stream, and supports conversion from YCbCr/YUV
to RGB pixel formats
Signed-off-by: Kieran Bingham <kieran+renesas@bingham.xyz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The FDP1 is a de-interlacing module which converts interlaced video to
progressive video. It is also capable of performing pixel format conversion
between YCbCr/YUV formats and RGB formats.
Signed-off-by: Kieran Bingham <kieran+renesas@bingham.xyz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The menu control selects the operation mode of a video deinterlacer. The
menu entries are driver specific.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran@bingham.xyz>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
When requesting the DMA channel it was mandatory that we do not have DMA
resource nor valid DMA channel via DT. In this case the
dma_request_slave_channel_compat() would fall back and request any channel
with SW trigger.
The same can be achieved with the dma_request_chan_by_mask() without the
misleading use of the DMAengine API - implying that the omap3isp does
need to have DMA resource or valid dma binding in DT.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
When parsing the graph the driver loops over all endpoints using
of_graph_get_next_endpoint(). The function handles reference counting of
the passed and returned nodes, so the returned node's reference count
must not be decreased manually in the normal path.
Move the offending of_node_put() call to the error path that requires
manual reference count handling.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The Rift CV1 Sensor has bInterfaceClass set to vendor specific, so we
need an entry in uvc_ids to probe it. Just as the Rift DK2 IR tracker,
it misreports the pixel format as YUYV instead of Y8.
The sensor is configured with a low exposure time and high black level
by default, so that only bright IR sources can be seen.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The CEC_LOG_ADDRS_FL_CDC_ONLY flag is missing at the documentation,
causing this warning:
Documentation/output/cec.h.rst:6: WARNING: undefined label: cec-log-addrs-fl-cdc-only (if the link has no caption the label must precede a section header)
Add a documentation for it, based on the commit that introduced the
flag.
Fixes: a69a168a1bd4 ("[media] cec: add proper support for CDC-Only CEC devices")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Make sure the TX counters are zeroed in the cec_msg struct.
Non-zero TX counters make no sense when a message is received,
and applications should not see non-zero values here.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The cec framework and the pulse8-cec driver have been moved out
of staging, so update the MAINTAINERS paths.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Update the TODOs explaining why these two drivers remain in
staging. The reason is that these drivers rely on userspace to
set the physical address, but that should come from the HDMI
output driver. This in turn needs the upcoming HDMI notifier
framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Now that the CEC framework has been moved out of staging and into the
mainline kernel we can do the same for the pulse8-cec driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
An inner for-loop reused the outer loop variable. This was
only noticeable with CEC adapters supporting more than one
logical address.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Replace bool by int or __u8 (when used in a struct).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The CEC_MSG_FL_REPLY_TO_FOLLOWERS message flag only makes sense for transmitted
messages where you want to wait for the reply.
Clear the flag in all other cases.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The last open issues have been addressed, so it is time to move
this out of staging and into the mainline and to move the public
cec headers to include/uapi/linux.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
CDC-Only CEC devices are CEC devices that can only handle CDC messages,
all other messages are ignored.
Add a flag to signal that this is a CDC-Only device and act accordingly.
Also add helper functions to identify if a CEC device is configured as a
CDC-Only device, a second TV, a switch or a processor, since these variations
cannot be determined by the logical address alone.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The CEC_MSG_INITIATE_ARC message is special since it is the ONLY
CEC message that accepts two possible valid replies:
CEC_MSG_REPORT_ARC_INITIATED and CEC_MSG_REPORT_ARC_TERMINATED.
So if the transmitted message is CEC_MSG_INITIATE_ARC and the remote
side replied with CEC_MSG_REPORT_ARC_INITIATED or CEC_MSG_REPORT_ARC_TERMINATED,
then a msg->reply value of CEC_MSG_REPORT_ARC_INITIATED or
CEC_MSG_REPORT_ARC_TERMINATED will match either reply.
I thought about either adding a second reply2 field, but that's ugly
for all other messages that have only one reply, and what if in the
future a new message is added that can have three replies?
Another option would be to add a cec_msg flag, but really, the combination
of CEC_MSG_REPORT_ARC_INITIATED and a reply value of one of the two
possible replies already functions as a flag.
Another advantage of this approach is that it is safe to re-use a
cec_msg struct. No need to zero a flags field or a reply2 field.
So since this really is an exception in the CEC specification, I
decided to implement it as an exception as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
As per the CEC specification:
- CEC messages with a too-small payload should be ignored.
- Broadcast messages that are only allowed as directed messages
should be ignored.
- Directed messages that are only allowed as broadcast messages
should be ignored.
Implement this in the core CEC framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Give the caller more control over how replies to a transmit are
handled. By default the reply will only go to the filehandle that
called CEC_TRANSMIT. If this new flag is set, then the reply will
also go to all followers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
By default the CEC_MSG_USER_CONTROL_PRESSED/RELEASED messages
are passed on to the follower(s) only. If the new
CEC_LOG_ADDRS_FL_ALLOW_RC_PASSTHRU flag is set in the
flags field of struct cec_log_addrs then these messages are also
passed on to the remote control input subsystem and they will appear
as keystrokes.
This used to be the default behavior, but now you have to explicitly
enable it. This is done to force the caller to think about possible
security issues (e.g. if these messages are used to enter passwords).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This uses Laurent's python script to convert all tables, dropping
the useless 'row' comments.
See commit c2b66cafdf02 ("[media] v4l: doc: Remove row numbers from tables")
for the script that was used.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
When the persistent state is restored, the all_device_types field
was never filled in. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The vmr_stat variable was filled with the contents of the control register,
not the status register. Classic copy-and-paste error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
vb2_qbuf will check the buffer index. If a driver overrides
vidioc_qbuf and use the buffer index, the driver needs to check
the index.
Signed-off-by: Wu-Cheng Li <wuchengli@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The code examples on how to enumerate controls were really long in the
tooth. Update them.
Using FLAG_NEXT_CTRL is preferred these days, so give that example first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Improve the internal CEC documentation. In particular add a section
that specifies that transmit-related interrupts should be processed
before receive interrupts.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
vpfe_enum_input()
Use a direct assignment for an array element which can be set over the
pointer variable "inp" instead of calling the function "memcpy" here.
Suggested-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
vpbe_set_output()
* A function was called over the pointer "setup_if_config" in the data
structure "venc_platform_data". But the return value was not used so far.
Thus assign it to the local variable "ret" which will be checked with
the next statement.
Fixes: 9a7f95ad1c946efdd7a7a72df27db738260a0fd8 ("[media] davinci vpbe: add dm365 VPBE display driver changes")
* Pass a value to this function call without storing it in an intermediate
variable before.
* Delete the local variable "if_params" which became unnecessary with
this refactoring.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This patch fixes the following checkpatch.pl error:
ERROR: Macros with complex values should be enclosed in parentheses
Signed-off-by: Maninder Singh <maninder.s2@samsung.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Obtain the correct timings based on the VIC code from the AVI InfoFrame.
It does a sanity check to see if at least the measured width and height
are in line with what the VIC code reports. If not, then use the timings
instead of the VIC code (as per the CEA-861 spec).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Now that the timings contain picture aspect ratio information,
we can support cropcap to return the pixel aspect ratio.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add a helper to find timings based on the CEA-861 VIC code. Also,
add a helper that returns the pixel aspect ratio based on the
v4l2_dv_timings struct.
[mchehab@s-opensource.com: fix coding style]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add the CEA-861 VIC, the HDMI VIC and the picture aspect ratio information
where applicable.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Document the new flags.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add picture aspect ratio information, the CEA-861 VIC (Video Identification
Code) and the HDMI VIC to struct v4l2_bt_timings.
The picture aspect was chosen rather than the pixel aspect since 1) the
CEA-861 standard uses picture aspect, and 2) pixel aspect ratio can become
tricky when dealing with pixel repeat timings. While we don't support those
yet at the moment, this might become necessary. And in that case using
picture aspect ratio makes more sense. And converting picture aspect ratio
to pixel aspect ratio is easy enough.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
