| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Kmemdup is better than kmalloc+memcpy. So replace them.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Variables 'tn' and 'oport' are being assigned but are never used hence
they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'oport' set but not used [-Wunused-but-set-variable]
warning: variable 'tn' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Suresh Reddy says:
====================
be2net: patch-set
v1->v2 : Modified the subject line and commit log.
Please consider applying these two patches to net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch handles a TX-timeout as follows:
1) This patch gathers and prints the following info that can
help in diagnosing the cause of a TX-timeout.
a) TX queue and completion queue entries.
b) SKB and TCP/UDP header details.
2) For Lancer NICs (TX-timeout recovery is not supported for
BE3/Skyhawk-R NICs), it recovers from the TX timeout as follows:
a) On a TX-timeout, driver sets the PHYSDEV_CONTROL_FW_RESET_MASK
bit in the PHYSDEV_CONTROL register. Lancer firmware goes into
an error state and indicates this back to the driver via a bit
in a doorbell register.
b) Driver detects this and calls be_err_recover(). DMA is disabled,
all pending TX skbs are unmapped and freed (be_close()). All rings
are destroyed (be_clear()).
c) The driver waits for the FW to re-initialize and re-creates all
rings along with other data structs (be_resume())
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a potential execution path in which variable *err* is returned
without being properly initialized previously.
Fix this by initializing variable *err* to 0.
Addresses-Coverity-ID: 1472116 ("Uninitialized scalar variable")
Fixes: 0ec13877ce95 ("net/mlx5e: Gather all XDP pre-requisite checks in a single function")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following sparse warning:
drivers/net/ethernet/qlogic/qed/qed_cxt.c:1534:6: warning: symbol 'qed_cm_init_pf' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:233:4: warning: symbol 'qed_init_qm_get_num_tcs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:238:5: warning: symbol 'qed_init_qm_get_num_vfs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:246:5: warning: symbol 'qed_init_qm_get_num_pf_rls' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:264:5: warning: symbol 'qed_init_qm_get_num_vports' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:276:5: warning: symbol 'qed_init_qm_get_num_pqs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:573:5: warning: symbol 'qed_mcp_nvm_wr_cmd' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:3012:1: warning: symbol '__qed_mcp_resc_lock' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:870:6: warning: symbol 'qed_dcbx_aen' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7841:5: warning: symbol 'qed_dbg_nvm_image_length' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7857:5: warning: symbol 'qed_dbg_nvm_image' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:675:6: warning: symbol '_qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:690:6: warning: symbol 'qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:3982:6: warning: symbol 'qed_iov_pf_get_pending_events' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_vf.c:172:5: warning: symbol '_qed_vf_pf_release' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:137:5: warning: symbol 'qed_rdma_get_sb_id' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:709:5: warning: symbol 'qed_rdma_stop' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_ll2.c:161:6: warning: symbol 'qed_ll2b_complete_rx_packet' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_roce.c:160:6: warning: symbol 'qed_roce_free_cid_pair' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:380:12: warning: symbol 'iwarp_state_names' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:946:1: warning: symbol 'qed_iwarp_parse_private_data' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:971:1: warning: symbol 'qed_iwarp_mpa_reply_arrived' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2504:1: warning: symbol 'qed_iwarp_ll2_slowpath' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2806:6: warning: symbol 'qed_iwarp_qp_in_error' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2827:6: warning: symbol 'qed_iwarp_exception_received' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2958:1: warning: symbol 'qed_iwarp_connect_complete' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iscsi.c:876:6: warning: symbol 'qed_iscsi_free_connection' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Denis Bolotin <Denis.Bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the IPv6 dependency from RDS.
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, rds_ib_conn_alloc() calls rds_ib_recv_alloc_caches()
without passing along the gfp_t flag. But rds_ib_recv_alloc_caches()
and rds_ib_recv_alloc_cache() should take a gfp_t parameter so that
rds_ib_recv_alloc_cache() can call alloc_percpu_gfp() using the
correct flag instead of calling alloc_percpu().
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace ugly macroses on functions.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We never use RCU protection for it, just a lot of cargo-cult
rcu_deference_protects calls.
Note that we do keep the kfree_rcu call for it, as the references through
struct sock are RCU protected and thus might require a grace period before
freeing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't maintain tx counters in rx stats any more. There's no need
for an extra container of rq stats.
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5b8f3c8d30a6 ("virtio_net: Add XDP related stats") tries to
count TX XDP stats in virtnet_receive(). This will cause several
issues:
- virtnet_xdp_sq() was called without checking whether or not XDP is
set. This may cause out of bound access when there's no enough txq
for XDP.
- Stats were updated even if there's no XDP/XDP_TX.
Fixing this by reusing virtnet_xdp_xmit() for XDP_TX which can counts
TX XDP counter itself and remove the unnecessary tx stats embedded in
rx stats.
Reported-by: syzbot+604f8271211546f5b3c7@syzkaller.appspotmail.com
Fixes: 5b8f3c8d30a6 ("virtio_net: Add XDP related stats")
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jakub Kicinski says:
====================
xsk: improvements to RX queue check and replace
First 3 patches of my recent RFC. The first one make the check against
real_num_rx_queues slightly more reliable, while the latter two redefine
XDP_QUERY_XSK_UMEM slightly to disallow replacing UMEM in the driver at
the stack level.
I'm not sure where this lays on the bpf vs net trees scale, but there
should be no conflicts with either tree.
====================
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently drivers have to check if they already have a umem
installed for a given queue and return an error if so. Make
better use of XDP_QUERY_XSK_UMEM and move this functionality
to the core.
We need to keep rtnl across the calls now.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Björn Töpel <bjorn.topel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return early and only take the ref on dev once there is no possibility
of failing.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Björn Töpel <bjorn.topel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We used to depend on real_num_rx_queues as a upper bound for sanity
checks. For AF_XDP socket validation it's useful if the check behaves
the same regardless of CONFIG_SYSFS setting.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 58b99ee3e3eb ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
forgot to return/free the xdp_frame in case the DMA mapping failed, correct this.
Also DMA unmap the frame in case mlx5e_xmit_xdp_frame() fails.
Fixes: 58b99ee3e3eb ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements following ethtool stats fields for netvsc:
cpu<n>_tx/rx_packets/bytes
cpu<n>_vf_tx/rx_packets/bytes
Corresponding per-cpu counters already exist in current code. Exposing
these counters will help troubleshooting performance issues.
for_each_present_cpu() was used instead of for_each_possible_cpu().
for_each_possible_cpu() would create very long and useless output.
It is still being used for internal buffer, but not for ethtool
output.
There could be an overflow if cpu was added between ethtool
call netvsc_get_sset_count() and netvsc_get_ethtool_stats() and
netvsc_get_strings(). (still safe if cpu was removed)
ethtool makes these three function calls separately.
As long as we use ethtool, I can't see any clean solution.
Currently and in foreseeable short term, Hyper-V doesn't support
cpu hot-plug. Plus, ethtool is for admin use. Unlikely the admin
would perform such combo operations.
Changes in v2:
- Remove cpp style comment
- Resubmit after freeze
Changes in v3:
- Reimplemented with kvmalloc instead of alloc_percpu
Changes in v4:
- Fixed inconsistent array size
- Use kvmalloc_array instead of kvmalloc
Signed-off-by: Yidong Ren <yidren@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Petr Machata says:
====================
A test for mirror-to-gretap with team in UL packet path
This patchset adds a test for "tc action mirred mirror" where the
mirrored-to device is a gretap, and underlay path contains a team
device.
In patch #1 require_command() is added, which should henceforth be used
to declare dependence on a certain tool.
In patch #2, two new functions, team_create() and team_destroy(), are
added to lib.sh.
The newly-added test uses arping, which isn't necessarily available.
Therefore patch #3 introduces $ARPING, and a preexisting test is fixed
to require_command $ARPING.
In patches #4 and #5, two new tests are added. In both cases, a team
device is on egress path of a mirrored packet in a mirror-to-gretap
scenario. In the first one, the team device is in loadbalance mode, in
the second one it's in lacp mode. (The difference in modes necessitates
a different testing strategy, hence two test cases instead of just
parameterizing one.)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This tests mirror-to-gretap when an underlay packet path includes a team
device which is not in loadbalance mode, but in LACP mode. The test
manipulates LAG membership to achieve changes in txability, thus making
sure that a driver that offloads mirror-to-gretap doesn't just consider
upness of a device.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test for "tc action mirred egress mirror" that mirrors to gretap when
the underlay route points at a VLAN-aware bridge (802.1q), and the
traffic egresses the bridge through a team device. Test upping and
downing individual team device slaves and verify the traffic flows as
expected.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on "arping" being installed everywhere under that
name, introduce a variable $ARPING like the other tools do.
Convert an existing test, mirror_gre_vlan_bridge_1q.sh to
require_command $ARPING and then invoke arping through the variable.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add team_create() and team_destroy() to manage team netdevices.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The logic for testing whether a certain command is available is used
several times in the current code base. The tests in follow-up patches
add more requirements like that.
Therefore extract the logic into a named function, require_command(),
that can be used directly from lib.sh as well as from any test that
wishes to declare dependence on some command.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kfree(NULL) is safe,so this removes NULL check before freeing the mem
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Extended Page Access is a 16-bit register, so change the page
parameter of vsc85xx_phy_page_set to a u16.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On receipt of a complete tls record, use socket's saved data_ready
callback instead of state_change callback. In function tls_queue(),
the TLS record is queued in encrypted state. But the decryption
happen inline when tls_sw_recvmsg() or tls_sw_splice_read() get invoked.
So it should be ok to notify the waiting context about the availability
of data as soon as we could collect a full TLS record. For new data
availability notification, sk_data_ready callback is more appropriate.
It points to sock_def_readable() which wakes up specifically for EPOLLIN
event. This is in contrast to the socket callback sk_state_change which
points to sock_def_wakeup() which issues a wakeup unconditionally
(without event mask).
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paolo Abeni says:
====================
TC: refactor act_mirred packets re-injection
This series is aimed at improving the act_mirred redirect performances.
Such action is used by OVS to represent TC S/W flows, and it's current largest
bottle-neck is the need for a skb_clone() for each packet.
The first 2 patches introduce some cleanup and safeguards to allow extending
tca_result - we will use it to store RCU protected redirect information - and
introduce a clear separation between user-space accessible tcfa_action
values and internal values accessible only by the kernel.
Then a new tcfa_action value is introduced: TC_ACT_REINJECT, similar to
TC_ACT_REDIRECT, but preserving the mirred semantic. Such value is not
accessible from user-space.
The last patch exploits the newly introduced infrastructure in the act_mirred
action, to avoid a skb_clone, when possible.
Overall this the above gives a ~10% performance improvement in forwarding tput,
when using the TC S/W datapath.
v1 -> v2:
- preserve the rcu lock in act_bpf
- add and use a new action value to reinject the packets, preserving the mirred
semantic
v2 -> v3:
- renamed to new action as TC_ACT_REINJECT
- TC_ACT_REINJECT is not exposed to user-space
v3 -> v4:
- dropped the TC_ACT_REDIRECT patch
- report failure via extack, too
- rename the new action as TC_ACT_REINSERT
- skip clone only if the control action don't touch tcf_result
v4 -> v5:
- fix a couple of build issue reported by kbuild bot
- dont split messages
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When mirred is invoked from the ingress path, and it wants to redirect
the processed packet, it can now use the TC_ACT_REINSERT action,
filling the tcf_result accordingly, and avoiding a per packet
skb_clone().
Overall this gives a ~10% improvement in forwarding performance for the
TC S/W data path and TC S/W performances are now comparable to the
kernel openvswitch datapath.
v1 -> v2: use ACT_MIRRED instead of ACT_REDIRECT
v2 -> v3: updated after action rename, fixed typo into the commit
message
v3 -> v4: updated again after action rename, added more comments to
the code (JiriP), skip the optimization if the control action
need to touch the tcf_result (Paolo)
v4 -> v5: fix sparse warning (kbuild bot)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is similar TC_ACT_REDIRECT, but with a slightly different
semantic:
- on ingress the mirred skbs are passed to the target device
network stack without any additional check not scrubbing.
- the rcu-protected stats provided via the tcf_result struct
are updated on error conditions.
This new tcfa_action value is not exposed to the user-space
and can be used only internally by clsact.
v1 -> v2: do not touch TC_ACT_REDIRECT code path, introduce
a new action type instead
v2 -> v3:
- rename the new action value TC_ACT_REINJECT, update the
helper accordingly
- take care of uncloned reinjected packets in XDP generic
hook
v3 -> v4:
- renamed again the new action value (JiriP)
v4 -> v5:
- fix build error with !NET_CLS_ACT (kbuild bot)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each lockless action currently does its own RCU locking in ->act().
This allows using plain RCU accessor, even if the context
is really RCU BH.
This change drops the per action RCU lock, replace the accessors
with the _bh variant, cleans up a bit the surrounding code and
documents the RCU status in the relevant header.
No functional nor performance change is intended.
The goal of this patch is clarifying that the RCU critical section
used by the tc actions extends up to the classifier's caller.
v1 -> v2:
- preserve rcu lock in act_bpf: it's needed by eBPF helpers,
as pointed out by Daniel
v3 -> v4:
- fixed some typos in the commit message (JiriP)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when initializing an action, the user-space can specify
and use arbitrary values for the tcfa_action field. If the value
is unknown by the kernel, is implicitly threaded as TC_ACT_UNSPEC.
This change explicitly checks for unknown values at action creation
time, and explicitly convert them to TC_ACT_UNSPEC. No functional
changes are introduced, but this will allow introducing tcfa_action
values not exposed to user-space in a later patch.
Note: we can't use the above to hide TC_ACT_REDIRECT from user-space,
as the latter is already part of uAPI.
v3 -> v4:
- use an helper to check for action validity (JiriP)
- emit an extack for invalid actions (JiriP)
v4 -> v5:
- keep messages on a single line, drop net_warn (Marcelo)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are no in-tree callers of cn23xx_dump_iq_regs.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Christoph Hellwig says:
====================
socket poll related cleanups v2
A couple of cleanups I stumbled upon when studying the networking
poll code.
Changes since v1:
- drop a dispute patch from this series (to be sent separately)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fold it into the only caller to make the code simpler and easier to read.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no point in hiding this logic in a helper. Also remove the
useless events != 0 check and only busy loop once we know we actually
have a poll method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For any open socket file descriptor sock->sk->sk_wq->wait will always
point to sock->wq->wait. That means we can do the shorter dereference
and removal a NULL check and don't have to not worry about any RCU
protection.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The wait_address argument is always directly derived from the filp
argument, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace calls to kmalloc followed by a memcpy with a direct call to
kmemdup.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace calls to kmalloc followed by a memcpy with a direct call to
kmemdup.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/sched/act_pedit.c:289:2-3: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are no in-tree callers of qed_get_cm_pq_idx_rl since it be there,
so it can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since driver is devicetree-based, all device type and charateristic can be
determined by the compatible string and its data. It's unnecessary to
create another dependent function to check chip ID and then decide whether
the specific funciton is being supported on a certain device. It can be
totally replaced by the existing flag, so a cleanup is made by removing
the function and the only user, HWLRO.
MT2701 also have a missing HWLRO support in old code, so add it the same
patch.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Improve more in the existing code by reusing dma_zalloc_coherent instead
of dma_alloc_coherent with __GFP_ZERO or superfluous zeroing buffer.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5f81880d5204 ("sysfs, kobject: allow creating kobject belonging
to arbitrary users") incorrectly changed the argument passed as the
parent parameter when calling sysfs_add_file_mode_ns(). This caused some
sysfs attribute files to not be added correctly to certain groups.
Fixes: 5f81880d5204 ("sysfs, kobject: allow creating kobject belonging to arbitrary users")
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-07-27 (Vxlan updates)
This series from Gal and Saeed provides updates to mlx5 vxlan implementation.
Gal, started with three cleanups to reflect the actual hardware vxlan state
- reflect 4789 UDP port default addition to software database
- check maximum number of vxlan UDP ports
- cleanup an unused member in vxlan work
Then Gal provides performance optimization by replacing the
vxlan radix tree with a hash table.
Measuring mlx5e_vxlan_lookup_port execution time:
Radix Tree Hash Table
--------------- ------------ ------------
Single Stream 161 ns 79 ns (51% improvement)
Multi Stream 259 ns 136 ns (47% improvement)
Measuring UDP stream packet rate, single fully utilized TX core:
Radix Tree: 498,300 PPS
Hash Table: 555,468 PPS (11% improvement)
Next, from Saeed, vxlan refactoring to allow sharing the vxlan table
between different mlx5 netdevice instances like PF and VF representors,
this is done by making mlx5 vxlan interface more generic and decoupling
it from PF netdevice structures and logic, then moving it into mlx5 core
as a low level interface so it can be used by VF representors, which is
illustrated in the last patch of the serious.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two problems in this test case:
- When indexing in bash associative array, the subscript is interpreted as
string, not as a variable name to be expanded.
- The keys stored to t0s and t1s are not DSCP values, but priority +
base (i.e. the logical DSCP value, not the full bitfield value).
In combination these two bugs conspire to make the test just work,
except it doesn't really test anything and always passes.
Fix the above two problems in obvious manner.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stephen Hemminger says:
====================
mtu related changes
While looking at other MTU issues, noticed a couple oppurtunties
for improving user experience.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an invalid MTU value is set through rtnetlink return extra error
information instead of putting message in kernel log. For other cases
where there is no visible API, keep the error report in the log.
Example:
# ip li set dev enp12s0 mtu 10000
Error: mtu greater than device maximum.
# ifconfig enp12s0 mtu 10000
SIOCSIFMTU: Invalid argument
# dmesg | tail -1
[ 2047.795467] enp12s0: mtu greater than device maximum
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
