Age | Commit message (Collapse) | Author | Files | Lines |
|
drivers/net/ipa/ipa_main.c
8afc7e471ad3 ("net: ipa: separate disabling setup from modem stop")
76b5fbcd6b47 ("net: ipa: kill ipa_modem_init()")
Duplicated include, drop one.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from netfilter.
Current release - regressions:
- r8169: fix incorrect mac address assignment
- vlan: fix underflow for the real_dev refcnt when vlan creation
fails
- smc: avoid warning of possible recursive locking
Current release - new code bugs:
- vsock/virtio: suppress used length validation
- neigh: fix crash in v6 module initialization error path
Previous releases - regressions:
- af_unix: fix change in behavior in read after shutdown
- igb: fix netpoll exit with traffic, avoid warning
- tls: fix splice_read() when starting mid-record
- lan743x: fix deadlock in lan743x_phy_link_status_change()
- marvell: prestera: fix bridge port operation
Previous releases - always broken:
- tcp_cubic: fix spurious Hystart ACK train detections for
not-cwnd-limited flows
- nexthop: fix refcount issues when replacing IPv6 groups
- nexthop: fix null pointer dereference when IPv6 is not enabled
- phylink: force link down and retrigger resolve on interface change
- mptcp: fix delack timer length calculation and incorrect early
clearing
- ieee802154: handle iftypes as u32, prevent shift-out-of-bounds
- nfc: virtual_ncidev: change default device permissions
- netfilter: ctnetlink: fix error codes and flags used for kernel
side filtering of dumps
- netfilter: flowtable: fix IPv6 tunnel addr match
- ncsi: align payload to 32-bit to fix dropped packets
- iavf: fix deadlock and loss of config during VF interface reset
- ice: avoid bpf_prog refcount underflow
- ocelot: fix broken PTP over IP and PTP API violations
Misc:
- marvell: mvpp2: increase MTU limit when XDP enabled"
* tag 'net-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (94 commits)
net: dsa: microchip: implement multi-bridge support
net: mscc: ocelot: correctly report the timestamping RX filters in ethtool
net: mscc: ocelot: set up traps for PTP packets
net: ptp: add a definition for the UDP port for IEEE 1588 general messages
net: mscc: ocelot: create a function that replaces an existing VCAP filter
net: mscc: ocelot: don't downgrade timestamping RX filters in SIOCSHWTSTAMP
net: hns3: fix incorrect components info of ethtool --reset command
net: hns3: fix one incorrect value of page pool info when queried by debugfs
net: hns3: add check NULL address for page pool
net: hns3: fix VF RSS failed problem after PF enable multi-TCs
net: qed: fix the array may be out of bound
net/smc: Don't call clcsock shutdown twice when smc shutdown
net: vlan: fix underflow for the real_dev refcnt
ptp: fix filter names in the documentation
ethtool: ioctl: fix potential NULL deref in ethtool_set_coalesce()
nfc: virtual_ncidev: change default device permissions
net/sched: sch_ets: don't peek at classes beyond 'nbands'
net: stmmac: Disable Tx queues when reconfiguring the interface
selftests: tls: test for correct proto_ops
tls: fix replacing proto_ops
...
|
|
Current driver version is able to handle only one bridge at time.
Configuring two bridges on two different ports would end up shorting this
bridges by HW. To reproduce it:
ip l a name br0 type bridge
ip l a name br1 type bridge
ip l s dev br0 up
ip l s dev br1 up
ip l s lan1 master br0
ip l s dev lan1 up
ip l s lan2 master br1
ip l s dev lan2 up
Ping on lan1 and get response on lan2, which should not happen.
This happened, because current driver version is storing one global "Port VLAN
Membership" and applying it to all ports which are members of any
bridge.
To solve this issue, we need to handle each port separately.
This patch is dropping the global port member storage and calculating
membership dynamically depending on STP state and bridge participation.
Note: STP support was broken before this patch and should be fixed
separately.
Fixes: c2e866911e25 ("net: dsa: microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20211126123926.2981028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a NULL pointer dereference in the CPPC library code and a
locking issue related to printing the names of ACPI device nodes in
the device properties framework.
Specifics:
- Fix NULL pointer dereference in the CPPC library code occuring on
hybrid systems without CPPC support (Rafael Wysocki).
- Avoid attempts to acquire a semaphore with interrupts off when
printing the names of ACPI device nodes and clean up code on top of
that fix (Sakari Ailus)"
* tag 'acpi-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: CPPC: Add NULL pointer check to cppc_get_perf()
ACPI: Make acpi_node_get_parent() local
ACPI: Get acpi_device's parent from the parent field
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These address three issues in the intel_pstate driver and fix two
problems related to hibernation.
Specifics:
- Make intel_pstate work correctly on Ice Lake server systems with
out-of-band performance control enabled (Adamos Ttofari).
- Fix EPP handling in intel_pstate during CPU offline and online in
the active mode (Rafael Wysocki).
- Make intel_pstate support ITMT on asymmetric systems with
overclocking enabled (Srinivas Pandruvada).
- Fix hibernation image saving when using the user space interface
based on the snapshot special device file (Evan Green).
- Make the hibernation code release the snapshot block device using
the same mode that was used when acquiring it (Thomas Zeitlhofer)"
* tag 'pm-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: hibernate: Fix snapshot partial write lengths
PM: hibernate: use correct mode for swsusp_close()
cpufreq: intel_pstate: ITMT support for overclocked system
cpufreq: intel_pstate: Fix active mode offline/online EPP handling
cpufreq: intel_pstate: Add Ice Lake server to out-of-band IDs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fix from Miklos Szeredi:
"Fix a regression caused by a bugfix in the previous release. The
symptom is a VM_BUG_ON triggered from splice to the fuse device.
Unfortunately the original bugfix was already backported to a number
of stable releases, so this fix-fix will need to be backported as
well"
* tag 'fuse-fixes-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: release pipe buf after last use
|
|
Vladimir Oltean says:
====================
Fix broken PTP over IP on Ocelot switches
Changes in v2: added patch 5, added Richard's ack for the whole series
sans patch 5 which is new.
Po Liu reported recently that timestamping PTP over IPv4 is broken using
the felix driver on NXP LS1028A. This has been known for a while, of
course, since it has always been broken. The reason is because IP PTP
packets are currently treated as unknown IP multicast, which is not
flooded to the CPU port in the ocelot driver design, so packets don't
reach the ptp4l program.
The series solves the problem by installing packet traps per port when
the timestamping ioctl is called, depending on the RX filter selected
(L2, L4 or both).
====================
Link: https://lore.kernel.org/r/20211126172845.3149260-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver doesn't support RX timestamping for non-PTP packets, but it
declares that it does. Restrict the reported RX filters to PTP v2 over
L2 and over L4.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IEEE 1588 support was declared too soon for the Ocelot switch. Out of
reset, this switch does not apply any special treatment for PTP packets,
i.e. when an event message is received, the natural tendency is to
forward it by MAC DA/VLAN ID. This poses a problem when the ingress port
is under a bridge, since user space application stacks (written
primarily for endpoint ports, not switches) like ptp4l expect that PTP
messages are always received on AF_PACKET / AF_INET sockets (depending
on the PTP transport being used), and never being autonomously
forwarded. Any forwarding, if necessary (for example in Transparent
Clock mode) is handled in software by ptp4l. Having the hardware forward
these packets too will cause duplicates which will confuse endpoints
connected to these switches.
So PTP over L2 barely works, in the sense that PTP packets reach the CPU
port, but they reach it via flooding, and therefore reach lots of other
unwanted destinations too. But PTP over IPv4/IPv6 does not work at all.
This is because the Ocelot switch have a separate destination port mask
for unknown IP multicast (which PTP over IP is) flooding compared to
unknown non-IP multicast (which PTP over L2 is) flooding. Specifically,
the driver allows the CPU port to be in the PGID_MC port group, but not
in PGID_MCIPV4 and PGID_MCIPV6. There are several presentations from
Allan Nielsen which explain that the embedded MIPS CPU on Ocelot
switches is not very powerful at all, so every penny they could save by
not allowing flooding to the CPU port module matters. Unknown IP
multicast did not make it.
The de facto consensus is that when a switch is PTP-aware and an
application stack for PTP is running, switches should have some sort of
trapping mechanism for PTP packets, to extract them from the hardware
data path. This avoids both problems:
(a) PTP packets are no longer flooded to unwanted destinations
(b) PTP over IP packets are no longer denied from reaching the CPU since
they arrive there via a trap and not via flooding
It is not the first time when this change is attempted. Last time, the
feedback from Allan Nielsen and Andrew Lunn was that the traps should
not be installed by default, and that PTP-unaware switching may be
desired for some use cases:
https://patchwork.ozlabs.org/project/netdev/patch/20190813025214.18601-5-yangbo.lu@nxp.com/
To address that feedback, the present patch adds the necessary packet
traps according to the RX filter configuration transmitted by user space
through the SIOCSHWTSTAMP ioctl. Trapping is done via VCAP IS2, where we
keep 5 filters, which are amended each time RX timestamping is enabled
or disabled on a port:
- 1 for PTP over L2
- 2 for PTP over IPv4 (UDP ports 319 and 320)
- 2 for PTP over IPv6 (UDP ports 319 and 320)
The cookie by which these filters (invisible to tc) are identified is
strategically chosen such that it does not collide with the filters used
for the ocelot-8021q tagging protocol by the Felix driver, or with the
MRP traps set up by the Ocelot library.
Other alternatives were considered, like patching user space to do
something, but there are so many ways in which PTP packets could be made
to reach the CPU, generically speaking, that "do what?" is a very valid
question. The ptp4l program from the linuxptp stack already attempts to
do something: it calls setsockopt(IP_ADD_MEMBERSHIP) (and
PACKET_ADD_MEMBERSHIP, respectively) which translates in both cases into
a dev_mc_add() on the interface, in the kernel:
https://github.com/richardcochran/linuxptp/blob/v3.1.1/udp.c#L73
https://github.com/richardcochran/linuxptp/blob/v3.1.1/raw.c
Reality shows that this is not sufficient in case the interface belongs
to a switchdev driver, as dev_mc_add() does not show the intention to
trap a packet to the CPU, but rather the intention to not drop it (it is
strictly for RX filtering, same as promiscuous does not mean to send all
traffic to the CPU, but to not drop traffic with unknown MAC DA). This
topic is a can of worms in itself, and it would be great if user space
could just stay out of it.
On the other hand, setting up PTP traps privately within the driver is
not new by any stretch of the imagination:
https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c#L833
https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/dsa/hirschmann/hellcreek.c#L1050
https://elixir.bootlin.com/linux/v5.16-rc2/source/include/linux/dsa/sja1105.h#L21
So this is the approach taken here as well. The difference here being
that we prepare and destroy the traps per port, dynamically at runtime,
as opposed to driver init time, because apparently, PTP-unaware
forwarding is a use case.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Reported-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As opposed to event messages (Sync, PdelayReq etc) which require
timestamping, general messages (Announce, FollowUp etc) do not.
In PTP they are part of different streams of data.
IEEE 1588-2008 Annex D.2 "UDP port numbers" states that the UDP
destination port assigned by IANA is 319 for event messages, and 320 for
general messages. Yet the kernel seems to be missing the definition for
general messages. This patch adds it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
VCAP (Versatile Content Aware Processor) is the TCAM-based engine behind
tc flower offload on ocelot, among other things. The ingress port mask
on which VCAP rules match is present as a bit field in the actual key of
the rule. This means that it is possible for a rule to be shared among
multiple source ports. When the rule is added one by one on each desired
port, that the ingress port mask of the key must be edited and rewritten
to hardware.
But the API in ocelot_vcap.c does not allow for this. For one thing,
ocelot_vcap_filter_add() and ocelot_vcap_filter_del() are not symmetric,
because ocelot_vcap_filter_add() works with a preallocated and
prepopulated filter and programs it to hardware, and
ocelot_vcap_filter_del() does both the job of removing the specified
filter from hardware, as well as kfreeing it. That is to say, the only
option of editing a filter in place, which is to delete it, modify the
structure and add it back, does not work because it results in
use-after-free.
This patch introduces ocelot_vcap_filter_replace, which trivially
reprograms a VCAP entry to hardware, at the exact same index at which it
existed before, without modifying any list or allocating any memory.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ocelot driver, when asked to timestamp all receiving packets, 1588
v1 or NTP, says "nah, here's 1588 v2 for you".
According to this discussion:
https://patchwork.kernel.org/project/netdevbpf/patch/20211104133204.19757-8-martin.kaistra@linutronix.de/#24577647
drivers that downgrade from a wider request to a narrower response (or
even a response where the intersection with the request is empty) are
buggy, and should return -ERANGE instead. This patch fixes that.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Guangbin Huang says:
====================
net: hns3: add some fixes for -net
This series adds some fixes for the HNS3 ethernet driver.
====================
Link: https://lore.kernel.org/r/20211126120318.33921-1-huangguangbin2@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, HNS3 driver doesn't clear the reset flags of components after
successfully executing reset, it causes userspace info of
"Components reset" and "Components not reset" is incorrect.
So fix this problem by clear corresponding reset flag after reset process.
Fixes: ddccc5e368a3 ("net: hns3: add support for triggering reset by ethtool")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, when user queries page pool info by debugfs command
"cat page_pool_info", the cnt of allocated page for page pool may be
incorrect because of memory inconsistency problem caused by compiler
optimization.
So this patch uses READ_ONCE() to read value of pages_state_hold_cnt to
fix this problem.
Fixes: 850bfb912a6d ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When page pool is not enabled, its address value is still NULL and page
pool should not be accessed, so add a check for it.
Fixes: 850bfb912a6d ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When PF is set to multi-TCs and configured mapping relationship between
priorities and TCs, the hardware will active these settings for this PF
and its VFs.
In this case when VF just uses one TC and its rx packets contain priority,
and if the priority is not mapped to TC0, as other TCs of VF is not valid,
hardware always put this kind of packets to the queue 0. It cause this kind
of packets of VF can not be used RSS function.
To fix this problem, set tc mode of all unused TCs of VF to the setting of
TC0, then rx packet with priority which map to unused TC will be direct to
TC0.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the variable 'p_bit->flags' is always 0,
the loop condition is always 0.
The variable 'j' may be greater than or equal to 32.
At this time, the array 'p_aeu->bits[32]' may be out
of bound.
Signed-off-by: zhangyue <zhangyue1@kylinos.cn>
Link: https://lore.kernel.org/r/20211125113610.273841-1-zhangyue1@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"One more fix to the lzo code, a missing put_page causing memory leaks
when some error branches are taken"
* tag 'for-5.16-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix the memory leak caused in lzo_compress_pages()
|
|
When applications call shutdown() with SHUT_RDWR in userspace,
smc_close_active() calls kernel_sock_shutdown(), and it is called
twice in smc_shutdown().
This fixes this by checking sk_state before do clcsock shutdown, and
avoids missing the application's call of smc_shutdown().
Link: https://lore.kernel.org/linux-s390/1f67548e-cbf6-0dce-82b5-10288a4583bd@linux.ibm.com/
Fixes: 606a63c9783a ("net/smc: Ensure the active closing peer first closes clcsock")
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20211126024134.45693-1-tonylu@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Combine two judgments that return the same value
Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211126013130.27112-1-samirweng1979@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Inject error before dev_hold(real_dev) in register_vlan_dev(),
and execute the following testcase:
ip link add dev dummy1 type dummy
ip link add name dummy1.100 link dummy1 type vlan id 100
ip link del dev dummy1
When the dummy netdevice is removed, we will get a WARNING as following:
=======================================================================
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 2 PID: 0 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0
and an endless loop of:
=======================================================================
unregister_netdevice: waiting for dummy1 to become free. Usage count = -1073741824
That is because dev_put(real_dev) in vlan_dev_free() be called without
dev_hold(real_dev) in register_vlan_dev(). It makes the refcnt of real_dev
underflow.
Move the dev_hold(real_dev) to vlan_dev_init() which is the call-back of
ndo_init(). That makes dev_hold() and dev_put() for vlan's real_dev
symmetrical.
Fixes: 563bcbae3ba2 ("net: vlan: fix a UAF in vlan_dev_real_dev()")
Reported-by: Petr Machata <petrm@nvidia.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/r/20211126015942.2918542-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All the filter names are missing _PTP in them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20211126031921.2466944-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ethtool_set_coalesce() now uses both the .get_coalesce() and
.set_coalesce() callbacks. But the check for their availability is
buggy, so changing the coalesce settings on a device where the driver
provides only _one_ of the callbacks results in a NULL pointer
dereference instead of an -EOPNOTSUPP.
Fix the condition so that the availability of both callbacks is
ensured. This also matches the netlink code.
Note that reproducing this requires some effort - it only affects the
legacy ioctl path, and needs a specific combination of driver options:
- have .get_coalesce() and .coalesce_supported but no
.set_coalesce(), or
- have .set_coalesce() but no .get_coalesce(). Here eg. ethtool doesn't
cause the crash as it first attempts to call ethtool_get_coalesce()
and bails out on error.
Fixes: f3ccfda19319 ("ethtool: extend coalesce setting uAPI with CQE mode")
Cc: Yufeng Mo <moyufeng@huawei.com>
Cc: Huazhong Tan <tanhuazhong@huawei.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Link: https://lore.kernel.org/r/20211126175543.28000-1-jwi@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Device permissions is S_IALLUGO, with many unnecessary bits. Remove them
and also remove read and write permissions from group and others.
Before the change:
crwsrwsrwt 1 0 0 10, 125 Nov 25 13:59 /dev/virtual_nci
After the change:
crw------- 1 0 0 10, 125 Nov 25 14:05 /dev/virtual_nci
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Link: https://lore.kernel.org/r/20211125141457.716921-1-cascardo@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
when the number of DRR classes decreases, the round-robin active list can
contain elements that have already been freed in ets_qdisc_change(). As a
consequence, it's possible to see a NULL dereference crash, caused by the
attempt to call cl->qdisc->ops->peek(cl->qdisc) when cl->qdisc is NULL:
BUG: kernel NULL pointer dereference, address: 0000000000000018
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 1 PID: 910 Comm: mausezahn Not tainted 5.16.0-rc1+ #475
Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014
RIP: 0010:ets_qdisc_dequeue+0x129/0x2c0 [sch_ets]
Code: c5 01 41 39 ad e4 02 00 00 0f 87 18 ff ff ff 49 8b 85 c0 02 00 00 49 39 c4 0f 84 ba 00 00 00 49 8b ad c0 02 00 00 48 8b 7d 10 <48> 8b 47 18 48 8b 40 38 0f ae e8 ff d0 48 89 c3 48 85 c0 0f 84 9d
RSP: 0000:ffffbb36c0b5fdd8 EFLAGS: 00010287
RAX: ffff956678efed30 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000002 RSI: ffffffff9b938dc9 RDI: 0000000000000000
RBP: ffff956678efed30 R08: e2f3207fe360129c R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000001 R12: ffff956678efeac0
R13: ffff956678efe800 R14: ffff956611545000 R15: ffff95667ac8f100
FS: 00007f2aa9120740(0000) GS:ffff95667b800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000018 CR3: 000000011070c000 CR4: 0000000000350ee0
Call Trace:
<TASK>
qdisc_peek_dequeued+0x29/0x70 [sch_ets]
tbf_dequeue+0x22/0x260 [sch_tbf]
__qdisc_run+0x7f/0x630
net_tx_action+0x290/0x4c0
__do_softirq+0xee/0x4f8
irq_exit_rcu+0xf4/0x130
sysvec_apic_timer_interrupt+0x52/0xc0
asm_sysvec_apic_timer_interrupt+0x12/0x20
RIP: 0033:0x7f2aa7fc9ad4
Code: b9 ff ff 48 8b 54 24 18 48 83 c4 08 48 89 ee 48 89 df 5b 5d e9 ed fc ff ff 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 f3 0f 1e fa <53> 48 83 ec 10 48 8b 05 10 64 33 00 48 8b 00 48 85 c0 0f 85 84 00
RSP: 002b:00007ffe5d33fab8 EFLAGS: 00000202
RAX: 0000000000000002 RBX: 0000561f72c31460 RCX: 0000561f72c31720
RDX: 0000000000000002 RSI: 0000561f72c31722 RDI: 0000561f72c31720
RBP: 000000000000002a R08: 00007ffe5d33fa40 R09: 0000000000000014
R10: 0000000000000000 R11: 0000000000000246 R12: 0000561f7187e380
R13: 0000000000000000 R14: 0000000000000000 R15: 0000561f72c31460
</TASK>
Modules linked in: sch_ets sch_tbf dummy rfkill iTCO_wdt intel_rapl_msr iTCO_vendor_support intel_rapl_common joydev virtio_balloon lpc_ich i2c_i801 i2c_smbus pcspkr ip_tables xfs libcrc32c crct10dif_pclmul crc32_pclmul crc32c_intel ahci libahci ghash_clmulni_intel serio_raw libata virtio_blk virtio_console virtio_net net_failover failover sunrpc dm_mirror dm_region_hash dm_log dm_mod
CR2: 0000000000000018
Ensuring that 'alist' was never zeroed [1] was not sufficient, we need to
remove from the active list those elements that are no more SP nor DRR.
[1] https://lore.kernel.org/netdev/60d274838bf09777f0371253416e8af71360bc08.1633609148.git.dcaratti@redhat.com/
v3: fix race between ets_qdisc_change() and ets_qdisc_dequeue() delisting
DRR classes beyond 'nbands' in ets_qdisc_change() with the qdisc lock
acquired, thanks to Cong Wang.
v2: when a NULL qdisc is found in the DRR active list, try to dequeue skb
from the next list item.
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: dcc68b4d8084 ("net: sch_ets: Add a new Qdisc")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Link: https://lore.kernel.org/r/7a5c496eed2d62241620bdbb83eb03fb9d571c99.1637762721.git.dcaratti@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Merge fix and cleanup related to the management of ACPI device
properties for 5.16-rc3.
* acpi-properties:
ACPI: Make acpi_node_get_parent() local
ACPI: Get acpi_device's parent from the parent field
|
|
Merge hibernation-related fixes for 5.16-rc3.
* pm-sleep:
PM: hibernate: Fix snapshot partial write lengths
PM: hibernate: use correct mode for swsusp_close()
|
|
The Tx queues were not disabled in situations where the driver needed to
stop the interface to apply a new configuration. This could result in a
kernel panic when doing any of the 3 following actions:
* reconfiguring the number of queues (ethtool -L)
* reconfiguring the size of the ring buffers (ethtool -G)
* installing/removing an XDP program (ip l set dev ethX xdp)
Prevent the panic by making sure netif_tx_disable is called when stopping
an interface.
Without this patch, the following kernel panic can be observed when doing
any of the actions above:
Unable to handle kernel paging request at virtual address ffff80001238d040
[....]
Call trace:
dwmac4_set_addr+0x8/0x10
dev_hard_start_xmit+0xe4/0x1ac
sch_direct_xmit+0xe8/0x39c
__dev_queue_xmit+0x3ec/0xaf0
dev_queue_xmit+0x14/0x20
[...]
[ end trace 0000000000000002 ]---
Fixes: 5fabb01207a2d ("net: stmmac: Add initial XDP support")
Fixes: aa042f60e4961 ("net: stmmac: Add support to Ethtool get/set ring parameters")
Fixes: 0366f7e06a6be ("net: stmmac: add ethtool support for get/set channels")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20211124154731.1676949-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fix from Greg KH:
"Here is a single binder driver fix for 5.16-rc3.
It resolves a problem reported in the set of binder fixes that went
into 5.16-rc1. It has been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
binder: fix test regression due to sender_euid change
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some small staging driver fixes and one driver removal for
5.16-rc3.
The fixes resolve a number of small issues found in 5.16-rc1, nothing
huge at all. The driver removal was due to a platform being removed in
5.16-rc1, but this driver was forgotten about. It wasn't being built
anymore so it's safe to delete.
All have been in linux-next for a while with no reported problems"
* tag 'staging-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8192e: Fix use after free in _rtl92e_pci_disconnect()
staging: greybus: Add missing rwsem around snd_ctl_remove() calls
staging: Remove Netlogic XLP network driver
staging: r8188eu: fix a memory leak in rtw_wx_read32()
staging: r8188eu: use GFP_ATOMIC under spinlock
staging: r8188eu: Use kzalloc() with GFP_ATOMIC in atomic context
staging/fbtft: Fix backlight
staging: r8188eu: Fix breakage introduced when 5G code was removed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for reported problems for
5.16-rc3
They include:
- typec driver fixes
- new usb-serial driver ids
- usb hub enumeration issues that were much reported
- gadget driver fixes
- dwc3 driver fix
- chipidea driver fixe
All of these have been in linux-next with no reported problems"
* tag 'usb-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: option: add Fibocom FM101-GL variants
usb: typec: tipd: Fix initialization sequence for cd321x
usb: typec: tipd: Fix typo in cd321x_switch_power_state
usb: hub: Fix locking issues with address0_mutex
USB: serial: pl2303: fix GC type detection
USB: serial: option: add Telit LE910S1 0x9200 composition
usb: chipidea: ci_hdrc_imx: fix potential error pointer dereference in probe
usb: hub: Fix usb enumeration issue due to address0 race
usb: typec: fusb302: Fix masking of comparator and bc_lvl interrupts
usb: dwc3: leave default DMA for PCI devices
usb: dwc2: hcd_queue: Fix use of floating point literal
usb: dwc3: gadget: Fix null pointer exception
usb: gadget: udc-xilinx: Fix an error handling path in 'xudc_probe()'
usb: xhci: tegra: Check padctrl interrupt presence in device tree
usb: dwc2: gadget: Fix ISOC flow for elapsed frames
usb: dwc3: gadget: Check for L1/L2/U3 for Start Transfer
usb: dwc3: gadget: Ignore NoStream after End Transfer
usb: dwc3: core: Revise GHWPARAMS9 offset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC host fixes from Ulf Hansson:
- mmc_spi: Add SPI IDs to silence warning
- sdhci: Fix ADMA for PAGE_SIZE >= 64KiB
- sdhci-esdhc-imx: Disable broken CMDQ for imx8qm/imx8qxp/imx8mm
* tag 'mmc-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: spi: Add device-tree SPI IDs
mmc: sdhci: Fix ADMA for PAGE_SIZE >= 64KiB
mmc: sdhci-esdhc-imx: disable CMDQ support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has an interrupt storm fix for the i801, better timeout handling
for the new virtio driver, and some documentation fixes this time"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
docs: i2c: smbus-protocol: mention the repeated start condition
i2c: virtio: disable timeout handling
i2c: i801: Fix interrupt storm from SMB_ALERT signal
i2c: i801: Restore INTREN on unload
dt-bindings: i2c: imx-lpi2c: Fix i.MX 8QM compatible matching
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- Kconfig fix to make it possible to control building of the privcmd
driver
- three fixes for issues identified by the kernel test robot
- a five-patch series to simplify timeout handling for Xen PV driver
initialization
- two patches to fix error paths in xenstore/xenbus driver
initialization
* tag 'for-linus-5.16c-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: make HYPERVISOR_set_debugreg() always_inline
xen: make HYPERVISOR_get_debugreg() always_inline
xen: detect uninitialized xenbus in xenbus_init
xen: flag xen_snd_front to be not essential for system boot
xen: flag pvcalls-front to be not essential for system boot
xen: flag hvc_xen to be not essential for system boot
xen: flag xen_drm_front to be not essential for system boot
xen: add "not_essential" flag to struct xenbus_driver
xen/pvh: add missing prototype to header
xen: don't continue xenstore initialization in case of errors
xen/privcmd: make option visible in Kconfig
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Three arm64 fixes.
The main one is a fix to the way in which we evaluate the macro
arguments to our uaccess routines, which we _think_ might be the root
cause behind some unkillable tasks we've seen in the Android arm64 CI
farm (testing is ongoing). In any case, it's worth fixing.
Other than that, we've toned down an over-zealous VM_BUG_ON() and
fixed ftrace stack unwinding in a bunch of cases.
Summary:
- Evaluate uaccess macro arguments outside of the critical section
- Tighten up VM_BUG_ON() in pmd_populate_kernel() to avoid false positive
- Fix ftrace stack unwinding using HAVE_FUNCTION_GRAPH_RET_ADDR_PTR"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: uaccess: avoid blocking within critical sections
arm64: mm: Fix VM_BUG_ON(mm != &init_mm) for trans_pgd
arm64: ftrace: use HAVE_FUNCTION_GRAPH_RET_ADDR_PTR
|
|
[BUG]
Fstests generic/027 is pretty easy to trigger a slow but steady memory
leak if run with "-o compress=lzo" mount option.
Normally one single run of generic/027 is enough to eat up at least 4G ram.
[CAUSE]
In commit d4088803f511 ("btrfs: subpage: make lzo_compress_pages()
compatible") we changed how @page_in is released.
But that refactoring makes @page_in only released after all pages being
compressed.
This leaves error path not releasing @page_in. And by "error path"
things like incompressible data will also be treated as an error
(-E2BIG).
Thus it can cause a memory leak if even nothing wrong happened.
[FIX]
Add check under @out label to release @page_in when needed, so when we
hit any error, the input page is properly released.
Reported-by: Josef Bacik <josef@toxicpanda.com>
Fixes: d4088803f511 ("btrfs: subpage: make lzo_compress_pages() compatible")
Reviewed-and-tested-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Eric Dumazet says:
====================
net: small csum optimizations
After recent x86 csum_partial() optimizations, we can more easily
see in kernel profiles costs of add/adc operations that could
be avoided, by feeding a non zero third argument to csum_partial()
====================
Link: https://lore.kernel.org/r/20211124202446.2917972-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove one pair of add/adc instructions and their dependency
against carry flag.
We can leverage third argument to csum_partial():
X = csum_block_sub(X, csum_partial(start, len, 0), 0);
-->
X = csum_block_add(X, ~csum_partial(start, len, 0), 0);
-->
X = ~csum_partial(start, len, ~X);
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We can leverage third argument to csum_partial():
X = csum_sub(X, csum_partial(start, len, 0));
-->
X = csum_add(X, ~csum_partial(start, len, 0));
-->
X = ~csum_partial(start, len, ~X);
This removes one add/adc pair and its dependency against the carry flag.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the probe timer is reused as the raise timer when PLPMTUD is in
the Search Complete state. raise_count was introduced to count how many
times the probe timer has timed out. When raise_count reaches to 30, the
raise timer handler will be triggered.
During the whole processing above, the timer keeps timing out every probe_
interval. It is a waste for the Search Complete state, as the raise timer
only needs to time out after 30 * probe_interval.
Since the raise timer and probe timer are never used at the same time, it
is no need to keep probe timer 'alive' in the Search Complete state. This
patch to introduce sctp_transport_reset_raise_timer() to start the timer
as the raise timer when entering the Search Complete state. When entering
the other states, sctp_transport_reset_probe_timer() will still be called
to reset the timer to the probe timer.
raise_count can be removed from sctp_transport as no need to count probe
timer timeout for raise timer timeout. last_rtx_chunks can be removed as
sctp_transport_reset_probe_timer() can be called in the place where asoc
rtx_data_chunks is changed.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/edb0e48988ea85997488478b705b11ddc1ba724a.1637781974.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a skb comes to tipc_aead_encrypt(), it's always linear. The
unlikely check 'skb_cloned(skb) && tailen <= skb_tailroom(skb)'
can completely be taken care of in skb_cow_data() by the code
in branch "if (!skb_has_frag_list())".
Also, remove the 'TODO:' annotation, as the pages in skbs are not
writable, see more on commit 3cf4375a0904 ("tipc: do not write
skb_shinfo frags when doing decrytion").
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Link: https://lore.kernel.org/r/47a478da0b6095b76e3cbe7a75cbd25d9da1df9a.1637773872.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Alex Elder says:
====================
net: ipa: GSI channel flow control
Starting with IPA v4.2, endpoint DELAY mode (which prevents data
transfer on TX endpoints) does not work properly. To address this,
changes were made to allow underlying GSI channels to be put into
a "flow controlled" state, which achieves a similar objective.
The first patch in this series implements the flow controlled
channel state and the commands used to control it. It arranges
to use the new mechanism--instead of DELAY mode--for IPA v4.2+.
In IPA v4.11, the notion of GSI channel flow control was enhanced,
and implemented in a slightly different way. For the most part this
doesn't affect the way the IPA driver uses flow control, but the
second patch adds support for the newer mechanism.
====================
Link: https://lore.kernel.org/r/20211124194416.707007-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPA v4.2 introduced GSI channel flow control, used instead of IPA
endpoint DELAY mode to prevent a TX channel from injecting packets
into the IPA core. It used a new FLOW_CONTROLLED channel state
which could be entered using GSI generic commands.
IPA v4.11 extended the channel flow control model. Rather than
having a distinct FLOW_CONTROLLED channel state, each channel has a
"flow control" property that can be enabled or not--independent of
the channel state. The AP (or modem) can modify this property using
the same GSI generic commands as before.
The AP only uses channel flow control on modem TX channels, and only
when recovering from a modem crash. The AP has no way to discover
the state of a modem channel, so the fact that (starting with IPA
v4.11) flow control no longer uses a distinct channel state is
invisible to the AP. So enhanced flow control generally does not
change the way AP uses flow control.
There are a few small differences, however:
- There is a notion of "primary" or "secondary" flow control, and
when enabling or disabling flow control that must be specified
in a new field in the GSI generic command register. For now, we
always specify 0 (meaning "primary").
- When disabling flow control, it's possible a request will need
to be retried. We retry up to 5 times in this case.
- Another new generic command allows the current flow control
state to be queried. We do not use this.
Other than the need for retries, the code essentially works the same
way as before.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
One quirk for certain versions of IPA is that endpoint DELAY mode
does not work properly. IPA DELAY mode prevents any packets from
being delivered to the IPA core for processing on a TX endpoint.
The AP uses DELAY mode when the modem crashes, to prevent modem TX
endpoints from generating traffic during crash recovery. Without
this, there is a chance the hardware will stall during recovery from
a modem crash.
To achieve a similar effect, a GSI FLOW_CONTROLLED channel state
was created. A STARTED TX channel can be placed in FLOW_CONTROLLED
state, which prevents the transfer of any more packets. A channel
in FLOW_CONTROLLED state can be either returned to STARTED state, or
can be transitioned to STOPPED state.
Because this operates on GSI channels, two generic commands were
added to allow the AP to control this state for modem channels
(similar to the ALLOCATE and HALT channel commands).
Previously the code assumed this quirk only applied to IPA v4.2.
In fact, channel flow control (rather than endpoint DELAY mode)
should be used for all versions *starting* with IPA v4.2.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jeremy Kerr says:
====================
mctp serial minor fixes
We had a few minor fixes queued for a v4 of the original series, so
they're sent here as separate changes.
v2:
- fix ordering of cancel_work vs. unregister_netdev.
====================
Link: https://lore.kernel.org/r/20211125060739.3023442-1-jk@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jiri assures me that a ldisc->open with tty->disc_data set should never
happen, so this check doesn't do anything.
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current serial driver requires a maximum MTU of 68, and it doesn't
make sense to set a MTU below the MCTP-required baseline (of 68) either.
This change sets the min_mtu & max_mtu of the mctp netdev, essentially
disallowing changes. By using these instead of a ndo_change_mtu op, we
get the netlink extacks reported too.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We want to ensure that the tx work has finished before returning from
the ldisc close op, so do a synchronous cancel.
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Alex Elder says:
====================
net: ipa: small collected improvements
This series contains a somewhat unrelated set of changes, some
inspired by some recent work posted for back-port. For the most
part they're meant to improve the code without changing it's
functionality. Each basically stands on its own.
====================
Link: https://lore.kernel.org/r/20211124202511.862588-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|