| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-08-18
This series contains updates to i40e and iavf drivers.
Arkadiusz fixes Flow Director not using the correct queue due to calling
the wrong pick Tx function for i40e.
Sylwester resolves traffic loss for iavf when it attempts to change its
MAC address when it does not have permissions to do so.
====================
Link: https://lore.kernel.org/r/20210818174217.4138922-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make changes to MAC address dependent on the response of PF.
Disallow changes to HW MAC address and MAC filter from untrusted
VF, thanks to that ping is not lost if VF tries to change MAC.
Add a new field in iavf_mac_filter, to indicate whether there
was response from PF for given filter. Based on this field pass
or discard the filter.
If untrusted VF tried to change it's address, it's not changed.
Still filter was changed, because of that ping couldn't go through.
Fixes: c5c922b3e09b ("iavf: fix MAC address setting for VFs when filter is rejected")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <Gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Without this patch, ATR does not work. Receive/transmit uses queue
selection based on SW DCB hashing method.
If traffic classes are not configured for PF, then use
netdev_pick_tx function for selecting queue for packet transmission.
Instead of calling i40e_swdcb_skb_tx_hash, call netdev_pick_tx,
which ensures that packet is transmitted/received from CPU that is
running the application.
Reproduction steps:
1. Load i40e driver
2. Map each MSI interrupt of i40e port for each CPU
3. Disable ntuple, enable ATR i.e.:
ethtool -K $interface ntuple off
ethtool --set-priv-flags $interface flow-director-atr
4. Run application that is generating traffic and is bound to a
single CPU, i.e.:
taskset -c 9 netperf -H 1.1.1.1 -t TCP_RR -l 10
5. Observe behavior:
Application's traffic should be restricted to the CPU provided in
taskset.
Fixes: 89ec1f0886c1 ("i40e: Fix queue-to-TC mapping on Tx")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2021-08-19
We've added 3 non-merge commits during the last 3 day(s) which contain
a total of 3 files changed, 29 insertions(+), 6 deletions(-).
The main changes are:
1) Fix to clear zext_dst for dead instructions which was causing invalid program
rejections on JITs with bpf_jit_needs_zext such as s390x, from Ilya Leoshkevich.
2) Fix RCU splat in bpf_get_current_{ancestor_,}cgroup_id() helpers when they are
invoked from sleepable programs, from Yonghong Song.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests, bpf: Test that dead ldx_w insns are accepted
bpf: Clear zext_dst of dead insns
bpf: Add rcu_read_lock in bpf_get_current_[ancestor_]cgroup_id() helpers
====================
Link: https://lore.kernel.org/r/20210819144904.20069-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The commit 2e6b836312a4 ("ASoC: intel: atom: Fix reference to PCM
buffer address") changed the reference of PCM buffer address to
substream->runtime->dma_addr as the buffer address may change
dynamically. However, I forgot that the dma_addr field is still not
set up for the CONTINUOUS buffer type (that this driver uses) yet in
5.14 and earlier kernels, and it resulted in garbage I/O. The problem
will be fixed in 5.15, but we need to address it quickly for now.
The fix is to deduce the address again from the DMA pointer with
virt_to_phys(), but from the right one, substream->runtime->dma_area.
Fixes: 2e6b836312a4 ("ASoC: intel: atom: Fix reference to PCM buffer address")
Reported-and-tested-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/2048c6aa-2187-46bd-6772-36a4fb3c5aeb@redhat.com
Link: https://lore.kernel.org/r/20210819152945.8510-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The mic has lots of noises if mic boost is enabled. So disable mic boost
to get crystal clear audio capture.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210818144119.121738-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fix for omap gpt12 timer error handling
Two of the recent fixes for ti-sysc driver had bad interaction for a
function return value that caused one of the fixes to not work so we
need to change the return value handling. Otherwise early beagleboard
variants still have a boot issue.
* tag 'omap-for-v5.14/gpt12-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix error handling for sysc_check_active_timer()
Link: https://lore.kernel.org/r/pull-1629354796-830948@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Two legacy PCI sysfs objects "legacy_io" and "legacy_mem" were updated
to use an unified address space in the commit 636b21b50152 ("PCI: Revoke
mappings like devmem"). This allows for revocations to be managed from
a single place when drivers want to take over and mmap() a /dev/mem
range.
Following the update, both of the sysfs objects should leverage the
iomem_get_mapping() function to get an appropriate address range, but
only the "legacy_io" has been correctly updated - the second attribute
seems to be using a wrong variable to pass the iomem_get_mapping()
function to.
Thus, correct the variable name used so that the "legacy_mem" sysfs
object would also correctly call the iomem_get_mapping() function.
Fixes: 636b21b50152 ("PCI: Revoke mappings like devmem")
Link: https://lore.kernel.org/r/20210812132144.791268-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The Renoir XHCI controller apparently doesn't resume reliably with the
standard D3hot-to-D0 delay. Increase it to 20ms.
[Alex: I talked to the AMD USB hardware team and the AMD Windows team and
they are not aware of any HW errata or specific issues. The HW works fine
in Windows. I was told Windows uses a rather generous default delay of
100ms for PCI state transitions.]
Link: https://lore.kernel.org/r/20210722025858.220064-1-alexander.deucher@amd.com
Signed-off-by: Marcin Bachry <hegel666@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Prike Liang <prike.liang@amd.com>
Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com>
|
|
Add Jim Quinlan, Nicolas Saenz Julienne, and Florian Fainelli as
maintainers of the Broadcom STB PCIe controller driver.
This driver is also included in these entries:
BROADCOM BCM2711/BCM2835 ARM ARCHITECTURE
BROADCOM BCM7XXX ARM ARCHITECTURE
which cover the Raspberry Pi specifics of the PCIe driver.
Link: https://lore.kernel.org/r/20210818225031.8502-1-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Hayes Wang says:
====================
r8152: fix bp settings
Fix the wrong bp settings of the firmware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The maximum PLA bp number of RTL8153C is 16, not 8. That is, the
bp 0 ~ 15 are at 0xfc28 ~ 0xfc46, and the bp_en is at 0xfc48.
Fixes: 195aae321c82 ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The register of USB_BP2_EN is 16 bits, so we should use
ocp_write_word(), not ocp_write_byte().
Fixes: 9370f2d05a2a ("support request_firmware for RTL8153")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mat Martineau says:
====================
mptcp: Bug fixes
Here are two bug fixes for the net tree:
Patch 1 fixes a memory leak that could be encountered when clearing the
list of advertised MPTCP addresses.
Patch 2 fixes a protocol issue early in an MPTCP connection, to ensure
both peers correctly understand that the full MPTCP connection handshake
has completed even when the server side quickly sends an ADD_ADDR
option.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If directly after an MP_CAPABLE 3WHS, the client receives an ADD_ADDR
with HMAC from the server, it is enough to switch to a "fully
established" mode because it has received more MPTCP options.
It was then OK to enable the "fully_established" flag on the MPTCP
socket. Still, best to check if the ADD_ADDR looks valid by looking if
it contains an HMAC (no 'echo' bit). If an ADD_ADDR echo is received
while we are not in "fully established" mode, it is strange and then
we should not switch to this mode now.
But that is not enough. On one hand, the path-manager has be notified
the state has changed. On the other hand, the "fully_established" flag
on the subflow socket should be turned on as well not to re-send the
MP_CAPABLE 3rd ACK content with the next ACK.
Fixes: 84dfe3677a6f ("mptcp: send out dedicated ADD_ADDR packet")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The endpoint cleanup path is prone to a memory leak, as reported
by syzkaller:
BUG: memory leak
unreferenced object 0xffff88810680ea00 (size 64):
comm "syz-executor.6", pid 6191, jiffies 4295756280 (age 24.138s)
hex dump (first 32 bytes):
58 75 7d 3c 80 88 ff ff 22 01 00 00 00 00 ad de Xu}<....".......
01 00 02 00 00 00 00 00 ac 1e 00 07 00 00 00 00 ................
backtrace:
[<0000000072a9f72a>] kmalloc include/linux/slab.h:591 [inline]
[<0000000072a9f72a>] mptcp_nl_cmd_add_addr+0x287/0x9f0 net/mptcp/pm_netlink.c:1170
[<00000000f6e931bf>] genl_family_rcv_msg_doit.isra.0+0x225/0x340 net/netlink/genetlink.c:731
[<00000000f1504a2c>] genl_family_rcv_msg net/netlink/genetlink.c:775 [inline]
[<00000000f1504a2c>] genl_rcv_msg+0x341/0x5b0 net/netlink/genetlink.c:792
[<0000000097e76f6a>] netlink_rcv_skb+0x148/0x430 net/netlink/af_netlink.c:2504
[<00000000ceefa2b8>] genl_rcv+0x24/0x40 net/netlink/genetlink.c:803
[<000000008ff91aec>] netlink_unicast_kernel net/netlink/af_netlink.c:1314 [inline]
[<000000008ff91aec>] netlink_unicast+0x537/0x750 net/netlink/af_netlink.c:1340
[<0000000041682c35>] netlink_sendmsg+0x846/0xd80 net/netlink/af_netlink.c:1929
[<00000000df3aa8e7>] sock_sendmsg_nosec net/socket.c:704 [inline]
[<00000000df3aa8e7>] sock_sendmsg+0x14e/0x190 net/socket.c:724
[<000000002154c54c>] ____sys_sendmsg+0x709/0x870 net/socket.c:2403
[<000000001aab01d7>] ___sys_sendmsg+0xff/0x170 net/socket.c:2457
[<00000000fa3b1446>] __sys_sendmsg+0xe5/0x1b0 net/socket.c:2486
[<00000000db2ee9c7>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<00000000db2ee9c7>] do_syscall_64+0x38/0x90 arch/x86/entry/common.c:80
[<000000005873517d>] entry_SYSCALL_64_after_hwframe+0x44/0xae
We should not require an allocation to cleanup stuff.
Rework the code a bit so that the additional RCU work is no more needed.
Fixes: 1729cf186d8a ("mptcp: create the listening socket for new port")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In __init_el2_timers we initialize CNTHCTL_EL2.{EL1PCEN,EL1PCTEN} with a
RMW sequence, leaving all other bits UNKNOWN.
In general, we should initialize all bits in a register rather than
using an RMW sequence, since most bits are UNKNOWN out of reset, and as
new bits are added to the reigster their reset value might not result in
expected behaviour.
In the case of CNTHCTL_EL2, FEAT_ECV added a number of new control bits
in previously RES0 bits, which reset to UNKNOWN values, and may cause
issues for EL1 and EL0:
* CNTHCTL_EL2.ECV enables the CNTPOFF_EL2 offset (which itself resets to
an UNKNOWN value) at EL0 and EL1. Since the offset could reset to
distinct values across CPUs, when the control bit resets to 1 this
could break timekeeping generally.
* CNTHCTL_EL2.{EL1TVT,EL1TVCT} trap EL0 and EL1 accesses to the EL1
virtual timer/counter registers to EL2. When reset to 1, this could
cause unexpected traps to EL2.
Initializing these bits to zero avoids these problems, and all other
bits in CNTHCTL_EL2 other than EL1PCEN and EL1PCTEN can safely be reset
to zero.
This patch ensures we initialize CNTHCTL_EL2 accordingly, only setting
EL1PCEN and EL1PCTEN, and setting all other bits to zero.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Oliver Upton <oupton@google.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Oliver Upton <oupton@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210818161535.52786-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Laurent reported that STRICT_MODULE_RWX was causing intermittent crashes
on one of his systems:
kernel tried to execute exec-protected page (c008000004073278) - exploit attempt? (uid: 0)
BUG: Unable to handle kernel instruction fetch
Faulting instruction address: 0xc008000004073278
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: drm virtio_console fuse drm_panel_orientation_quirks ...
CPU: 3 PID: 44 Comm: kworker/3:1 Not tainted 5.14.0-rc4+ #12
Workqueue: events control_work_handler [virtio_console]
NIP: c008000004073278 LR: c008000004073278 CTR: c0000000001e9de0
REGS: c00000002e4ef7e0 TRAP: 0400 Not tainted (5.14.0-rc4+)
MSR: 800000004280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 24002822 XER: 200400cf
...
NIP fill_queue+0xf0/0x210 [virtio_console]
LR fill_queue+0xf0/0x210 [virtio_console]
Call Trace:
fill_queue+0xb4/0x210 [virtio_console] (unreliable)
add_port+0x1a8/0x470 [virtio_console]
control_work_handler+0xbc/0x1e8 [virtio_console]
process_one_work+0x290/0x590
worker_thread+0x88/0x620
kthread+0x194/0x1a0
ret_from_kernel_thread+0x5c/0x64
Jordan, Fabiano & Murilo were able to reproduce and identify that the
problem is caused by the call to module_enable_ro() in do_init_module(),
which happens after the module's init function has already been called.
Our current implementation of change_page_attr() is not safe against
concurrent accesses, because it invalidates the PTE before flushing the
TLB and then installing the new PTE. That leaves a window in time where
there is no valid PTE for the page, if another CPU tries to access the
page at that time we see something like the fault above.
We can't simply switch to set_pte_at()/flush TLB, because our hash MMU
code doesn't handle a set_pte_at() of a valid PTE. See [1].
But we do have pte_update(), which replaces the old PTE with the new,
meaning there's no window where the PTE is invalid. And the hash MMU
version hash__pte_update() deals with synchronising the hash page table
correctly.
[1]: https://lore.kernel.org/linuxppc-dev/87y318wp9r.fsf@linux.ibm.com/
Fixes: 1f9ad21c3b38 ("powerpc/mm: Implement set_memory() routines")
Reported-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Murilo Opsfelder Araújo <muriloo@linux.ibm.com>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210818120518.3603172-1-mpe@ellerman.id.au
|
|
Commit b5efec00b671 ("powerpc/32s: Move KUEP locking/unlocking in C")
removed the 'isync' instruction after adding/removing NX bit in user
segments. The reasoning behind this change was that when setting the
NX bit we don't mind it taking effect with delay as the kernel never
executes text from userspace, and when clearing the NX bit this is
to return to userspace and then the 'rfi' should synchronise the
context.
However, it looks like on book3s/32 having a hash page table, at least
on the G3 processor, we get an unexpected fault from userspace, then
this is followed by something wrong in the verification of MSR_PR
at end of another interrupt.
This is fixed by adding back the removed isync() following update
of NX bit in user segment registers. Only do it for cores with an
hash table, as 603 cores don't exhibit that problem and the two isync
increase ./null_syscall selftest by 6 cycles on an MPC 832x.
First problem: unexpected WARN_ON() for mysterious PROTFAULT
WARNING: CPU: 0 PID: 1660 at arch/powerpc/mm/fault.c:354 do_page_fault+0x6c/0x5b0
Modules linked in:
CPU: 0 PID: 1660 Comm: Xorg Not tainted 5.13.0-pmac-00028-gb3c15b60339a #40
NIP: c001b5c8 LR: c001b6f8 CTR: 00000000
REGS: e2d09e40 TRAP: 0700 Not tainted (5.13.0-pmac-00028-gb3c15b60339a)
MSR: 00021032 <ME,IR,DR,RI> CR: 42d04f30 XER: 20000000
GPR00: c000424c e2d09f00 c301b680 e2d09f40 0000001e 42000000 00cba028 00000000
GPR08: 08000000 48000010 c301b680 e2d09f30 22d09f30 00c1fff0 00cba000 a7b7ba4c
GPR16: 00000031 00000000 00000000 00000000 00000000 00000000 a7b7b0d0 00c5c010
GPR24: a7b7b64c a7b7d2f0 00000004 00000000 c1efa6c0 00cba02c 00000300 e2d09f40
NIP [c001b5c8] do_page_fault+0x6c/0x5b0
LR [c001b6f8] do_page_fault+0x19c/0x5b0
Call Trace:
[e2d09f00] [e2d09f04] 0xe2d09f04 (unreliable)
[e2d09f30] [c000424c] DataAccess_virt+0xd4/0xe4
--- interrupt: 300 at 0xa7a261dc
NIP: a7a261dc LR: a7a253bc CTR: 00000000
REGS: e2d09f40 TRAP: 0300 Not tainted (5.13.0-pmac-00028-gb3c15b60339a)
MSR: 0000d032 <EE,PR,ME,IR,DR,RI> CR: 228428e2 XER: 20000000
DAR: 00cba02c DSISR: 42000000
GPR00: a7a27448 afa6b0e0 a74c35c0 a7b7b614 0000001e a7b7b614 00cba028 00000000
GPR08: 00020fd9 00000031 00cb9ff8 a7a273b0 220028e2 00c1fff0 00cba000 a7b7ba4c
GPR16: 00000031 00000000 00000000 00000000 00000000 00000000 a7b7b0d0 00c5c010
GPR24: a7b7b64c a7b7d2f0 00000004 00000002 0000001e a7b7b614 a7b7aff4 00000030
NIP [a7a261dc] 0xa7a261dc
LR [a7a253bc] 0xa7a253bc
--- interrupt: 300
Instruction dump:
7c4a1378 810300a0 75278410 83820298 83a300a4 553b018c 551e0036 4082038c
2e1b0000 40920228 75280800 41820220 <0fe00000> 3b600000 41920214 81420594
Second problem: MSR PR is seen unset allthough the interrupt frame shows it set
kernel BUG at arch/powerpc/kernel/interrupt.c:458!
Oops: Exception in kernel mode, sig: 5 [#1]
BE PAGE_SIZE=4K MMU=Hash SMP NR_CPUS=2 PowerMac
Modules linked in:
CPU: 0 PID: 1660 Comm: Xorg Tainted: G W 5.13.0-pmac-00028-gb3c15b60339a #40
NIP: c0011434 LR: c001629c CTR: 00000000
REGS: e2d09e70 TRAP: 0700 Tainted: G W (5.13.0-pmac-00028-gb3c15b60339a)
MSR: 00029032 <EE,ME,IR,DR,RI> CR: 42d09f30 XER: 00000000
GPR00: 00000000 e2d09f30 c301b680 e2d09f40 83440000 c44d0e68 e2d09e8c 00000000
GPR08: 00000002 00dc228a 00004000 e2d09f30 22d09f30 00c1fff0 afa6ceb4 00c26144
GPR16: 00c25fb8 00c26140 afa6ceb8 90000000 00c944d8 0000001c 00000000 00200000
GPR24: 00000000 000001fb afa6d1b4 00000001 00000000 a539a2a0 a530fd80 00000089
NIP [c0011434] interrupt_exit_kernel_prepare+0x10/0x70
LR [c001629c] interrupt_return+0x9c/0x144
Call Trace:
[e2d09f30] [c000424c] DataAccess_virt+0xd4/0xe4 (unreliable)
--- interrupt: 300 at 0xa09be008
NIP: a09be008 LR: a09bdfe8 CTR: a09bdfc0
REGS: e2d09f40 TRAP: 0300 Tainted: G W (5.13.0-pmac-00028-gb3c15b60339a)
MSR: 0000d032 <EE,PR,ME,IR,DR,RI> CR: 420028e2 XER: 20000000
DAR: a539a308 DSISR: 0a000000
GPR00: a7b90d50 afa6b2d0 a74c35c0 a0a8b690 a0a8b698 a5365d70 a4fa82a8 00000004
GPR08: 00000000 a09bdfc0 00000000 a5360000 a09bde7c 00c1fff0 afa6ceb4 00c26144
GPR16: 00c25fb8 00c26140 afa6ceb8 90000000 00c944d8 0000001c 00000000 00200000
GPR24: 00000000 000001fb afa6d1b4 00000001 00000000 a539a2a0 a530fd80 00000089
NIP [a09be008] 0xa09be008
LR [a09bdfe8] 0xa09bdfe8
--- interrupt: 300
Instruction dump:
80010024 83e1001c 7c0803a6 4bffff80 3bc00800 4bffffd0 486b42fd 4bffffcc
81430084 71480002 41820038 554a0462 <0f0a0000> 80620060 74630001 40820034
Fixes: b5efec00b671 ("powerpc/32s: Move KUEP locking/unlocking in C")
Cc: stable@vger.kernel.org # v5.13+
Reported-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/4856f5574906e2aec0522be17bf3848a22b2cd0b.1629269345.git.christophe.leroy@csgroup.eu
|
|
Function "dma_map_sg" is entitled to merge adjacent entries
and return a value smaller than what was passed as "nents".
Subsequently "ib_map_mr_sg" needs to work with this value ("sg_dma_len")
rather than the original "nents" parameter ("sg_len").
This old RDS bug was exposed and reliably causes kernel panics
(using RDMA operations "rds-stress -D") on x86_64 starting with:
commit c588072bba6b ("iommu/vt-d: Convert intel iommu driver to the iommu ops")
Simply put: Linux 5.11 and later.
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Link: https://lore.kernel.org/r/60efc69f-1f35-529d-a7ef-da0549cad143@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently we are unable to ping a bridge on top of a felix switch which
uses the ocelot-8021q tagger. The packets are dropped on the ingress of
the user port and the 'drop_local' counter increments (the counter which
denotes drops due to no valid destinations).
Dumping the PGID tables, it becomes clear that the PGID_SRC of the user
port is zero, so it has no valid destinations.
But looking at the code, the cpu_fwd_mask (the bit mask of DSA tag_8021q
ports) is clearly missing from the forwarding mask of ports that are
under a bridge. So this has always been broken.
Looking at the version history of the patch, in v7
https://patchwork.kernel.org/project/netdevbpf/patch/20210125220333.1004365-12-olteanv@gmail.com/
the code looked like this:
/* Standalone ports forward only to DSA tag_8021q CPU ports */
unsigned long mask = cpu_fwd_mask;
(...)
} else if (ocelot->bridge_fwd_mask & BIT(port)) {
mask |= ocelot->bridge_fwd_mask & ~BIT(port);
while in v8 (the merged version)
https://patchwork.kernel.org/project/netdevbpf/patch/20210129010009.3959398-12-olteanv@gmail.com/
it looked like this:
unsigned long mask;
(...)
} else if (ocelot->bridge_fwd_mask & BIT(port)) {
mask = ocelot->bridge_fwd_mask & ~BIT(port);
So the breakage was introduced between v7 and v8 of the patch.
Fixes: e21268efbe26 ("net: dsa: felix: perform switch setup for tag_8021q")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210817160425.3702809-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
[why]
dcn301_calculate_wm_and_dl() causes flickering when external monitor is
connected.
This issue has been fixed before by commit 0e4c0ae59d7e
("drm/amdgpu/display: drop dcn301_calculate_wm_and_dl for now"), however
part of the fix was gone after commit 2cbcb78c9ee5 ("Merge tag 'amd-drm-next-5.13-2021-03-23' of https://gitlab.freedesktop.org/agd5f/linux into drm-next").
[how]
Use dcn30_calculate_wm_and_dlg() instead as in the original fix.
Fixes: 2cbcb78c9ee5 ("Merge tag 'amd-drm-next-5.13-2021-03-23' of https://gitlab.freedesktop.org/agd5f/linux into drm-next")
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Oliver Logush <oliver.logush@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"One more fix for cross-rename, adding a missing check for directory
and subvolume, this could lead to a crash"
* tag 'for-5.14-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: prevent rename2 from exchanging a subvol with a directory from different parents
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Only a few regression fixes and trivial device quirks"
* tag 'sound-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/via: Apply runtime PM workaround for ASUS B23E
ALSA: hda: Fix hang during shutdown due to link reset
ALSA: hda/realtek: Enable 4-speaker output for Dell XPS 15 9510 laptop
ALSA: oxfw: fix functioal regression for silence in Apogee Duet FireWire
ALSA: hda - fix the 'Capture Switch' value change notifications
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull clang cfi fix from Kees Cook:
- Use rcu_read_{un}lock_sched_notrace to avoid recursion (Elliot Berman)
* tag 'cfi-v5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
cfi: Use rcu_read_{un}lock_sched_notrace
|
|
I had forgotten just how sensitive hackbench is to extra pipe wakeups,
and commit 3a34b13a88ca ("pipe: make pipe writes always wake up
readers") ended up causing a quite noticeable regression on larger
machines.
Now, hackbench isn't necessarily a hugely meaningful benchmark, and it's
not clear that this matters in real life all that much, but as Mel
points out, it's used often enough when comparing kernels and so the
performance regression shows up like a sore thumb.
It's easy enough to fix at least for the common cases where pipes are
used purely for data transfer, and you never have any exciting poll
usage at all. So set a special 'poll_usage' flag when there is polling
activity, and make the ugly "EPOLLET has crazy legacy expectations"
semantics explicit to only that case.
I would love to limit it to just the broken EPOLLET case, but the pipe
code can't see the difference between epoll and regular select/poll, so
any non-read/write waiting will trigger the extra wakeup behavior. That
is sufficient for at least the hackbench case.
Apart from making the odd extra wakeup cases more explicitly about
EPOLLET, this also makes the extra wakeup be at the _end_ of the pipe
write, not at the first write chunk. That is actually much saner
semantics (as much as you can call any of the legacy edge-triggered
expectations for EPOLLET "sane") since it means that you know the wakeup
will happen once the write is done, rather than possibly in the middle
of one.
[ For stable people: I'm putting a "Fixes" tag on this, but I leave it
up to you to decide whether you actually want to backport it or not.
It likely has no impact outside of synthetic benchmarks - Linus ]
Link: https://lore.kernel.org/lkml/20210802024945.GA8372@xsang-OptiPlex-9020/
Fixes: 3a34b13a88ca ("pipe: make pipe writes always wake up readers")
Reported-by: kernel test robot <oliver.sang@intel.com>
Tested-by: Sandeep Patil <sspatil@android.com>
Tested-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Reported as working here:
https://github.com/t-8ch/linux-gigabyte-wmi-driver/issues/1#issuecomment-901207693
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20210818164435.99821-1-linux@weissschuh.net
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Commit a20dcf53ea98 ("usb: typec: tcpm: Respond Not_Supported if no
snk_vdo"), stops tcpm_pd_data_request() calling tcpm_handle_vdm_request()
when port->nr_snk_vdo is not set. But the VDM might be intended for an
altmode-driver, in which case nr_snk_vdo does not matter.
This change breaks the forwarding of connector hotplug (HPD) events
for displayport altmode on devices which don't set nr_snk_vdo.
tcpm_pd_data_request() is the only caller of tcpm_handle_vdm_request(),
so we can move the nr_snk_vdo check to inside it, at which point we
have already looked up the altmode device so we can check for this too.
Doing this check here also ensures that vdm_state gets set to
VDM_STATE_DONE if it was VDM_STATE_BUSY, even if we end up with
responding with PD_MSG_CTRL_NOT_SUPP later.
Note that tcpm_handle_vdm_request() was already sending
PD_MSG_CTRL_NOT_SUPP in some circumstances, after moving the nr_snk_vdo
check the same error-path is now taken when that check fails. So that
we have only one error-path for this and not two. Replace the
tcpm_queue_message(PD_MSG_CTRL_NOT_SUPP) used by the existing error-path
with the more robust tcpm_pd_handle_msg() from the (now removed) second
error-path.
Fixes: a20dcf53ea98 ("usb: typec: tcpm: Respond Not_Supported if no snk_vdo")
Cc: stable <stable@vger.kernel.org>
Cc: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210816154632.381968-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Compiling ppc64le_defconfig with clang-14 shows a modpost warning:
WARNING: modpost: vmlinux.o(.text+0xa74e0): Section mismatch in
reference from the function xive_setup_cpu_ipi() to the function
.init.text:xive_request_ipi()
The function xive_setup_cpu_ipi() references
the function __init xive_request_ipi().
This is often because xive_setup_cpu_ipi lacks a __init
annotation or the annotation of xive_request_ipi is wrong.
xive_request_ipi() is called from xive_setup_cpu_ipi(), which is not
__init, so xive_request_ipi() should not be marked __init. Remove the
attribute so there is no more warning.
Fixes: cbc06f051c52 ("powerpc/xive: Do not skip CPU-less nodes when creating the IPIs")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210816185711.21563-1-nathan@kernel.org
|
|
The symbol isn't needed outside of i915.ko.
Fixes: b30edfd8d0b4 ("drm/i915: Switch to LTTPR non-transparent mode link training")
Fixes: 264613b406eb ("drm/i915: Disable LTTPR support when the DPCD rev < 1.4")
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210816071737.2917-1-jani.nikula@intel.com
(cherry picked from commit d8959fb33890ba1956c142e83398e89812450ffc)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
ADL-P supports stream splitter on pipe B in addition to pipe A. Update
the sanity check in intel_ddi_mso_get_config() to reflect this, and
remove the check in intel_ddi_mso_configure() as redundant with
encoder->pipe_mask. Abstract the splitter pipe mask to a single point of
truth while at it to avoid similar mistakes in the future.
Fixes: 7bc188cc2c8c ("drm/i915/adl_p: enable MSO on pipe B")
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Tested-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210812132354.10885-1-jani.nikula@intel.com
(cherry picked from commit f6864b27d6d324771d979694de7ca455afbad32a)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
dispcnlunit1_cp_xosc_clkreq clock observed to be active on TGL-H platform
despite Wa_14010685332 original sequence,
thus blocks entry to deeper s0ix state.
The Tweaked Wa_14010685332 sequence fixes this issue, therefore use tweaked
Wa_14010685332 sequence for every PCH since PCH_CNP.
v2:
- removed RKL from comment and simplified condition. [Rodrigo]
Fixes: b896898c7369 ("drm/i915: Tweaked Wa_14010685332 for PCHs used on gen11 platforms")
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210810113112.31739-2-anshuman.gupta@intel.com
(cherry picked from commit 8b46cc6577f4bbef7e5909bb926da31d705f350f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
This fixes improper iotlb invalidation in intel_pasid_tear_down_entry().
When a PASID was used as nested mode, released and reused, the following
error message will appear:
[ 180.187556] Unexpected page request in Privilege Mode
[ 180.187565] Unexpected page request in Privilege Mode
[ 180.279933] Unexpected page request in Privilege Mode
[ 180.279937] Unexpected page request in Privilege Mode
Per chapter 6.5.3.3 of VT-d spec 3.3, when tear down a pasid entry, the
software should use Domain selective IOTLB flush if the PGTT of the pasid
entry is SL only or Nested, while for the pasid entries whose PGTT is FL
only or PT using PASID-based IOTLB flush is enough.
Fixes: 2cd1311a26673 ("iommu/vt-d: Add set domain DOMAIN_ATTR_NESTING attr")
Signed-off-by: Kumar Sanjay K <sanjay.k.kumar@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Tested-by: Yi Sun <yi.y.sun@intel.com>
Link: https://lore.kernel.org/r/20210817042425.1784279-1-yi.l.liu@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210817124321.1517985-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
A PASID reference is increased whenever a device is bound to an mm (and
its PASID) successfully (i.e. the device's sdev user count is increased).
But the reference is not dropped every time the device is unbound
successfully from the mm (i.e. the device's sdev user count is decreased).
The reference is dropped only once by calling intel_svm_free_pasid() when
there isn't any device bound to the mm. intel_svm_free_pasid() drops the
reference and only frees the PASID on zero reference.
Fix the issue by dropping the PASID reference and freeing the PASID when
no reference on successful unbinding the device by calling
intel_svm_free_pasid() .
Fixes: 4048377414162 ("iommu/vt-d: Use iommu_sva_alloc(free)_pasid() helpers")
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20210813181345.1870742-1-fenghua.yu@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210817124321.1517985-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Syzbot reported uninit-value in asix_mdio_read(). The problem was in
missing error handling. asix_read_cmd() should initialize passed stack
variable smsr, but it can fail in some cases. Then while condidition
checks possibly uninit smsr variable.
Since smsr is uninitialized stack variable, driver can misbehave,
because smsr will be random in case of asix_read_cmd() failure.
Fix it by adding error handling and just continue the loop instead of
checking uninit value.
Added helper function for checking Host_En bit, since wrong loop was used
in 4 functions and there is no need in copy-pasting code parts.
Cc: Robert Foss <robert.foss@collabora.com>
Fixes: d9fe64e51114 ("net: asix: Add in_pm parameter")
Reported-by: syzbot+a631ec9e717fb0423053@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fq qdisc requires tstamp to be cleared in the forwarding path. Now ovs
doesn't clear skb->tstamp. We encountered a problem with linux
version 5.4.56 and ovs version 2.14.1, and packets failed to
dequeue from qdisc when fq qdisc was attached to ovs port.
Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: kaixi.fan <fankaixi.li@bytedance.com>
Signed-off-by: xiexiaohui <xiexiaohui.xxh@bytedance.com>
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Saravana Kannan says:
====================
Clean up and fix error handling in mdio_mux_init()
This patch series was started due to -EPROBE_DEFER not being handled
correctly in mdio_mux_init() and causing issues [1]. While at it, I also
did some more error handling fixes and clean ups. The -EPROBE_DEFER fix is
the last patch.
Ideally, in the last patch we'd treat any error similar to -EPROBE_DEFER
but I'm not sure if it'll break any board/platforms where some child
mdiobus never successfully registers. If we treated all errors similar to
-EPROBE_DEFER, then none of the child mdiobus will work and that might be a
regression. If people are sure this is not a real case, then I can fix up
the last patch to always fail the entire mdio-mux init if any of the child
mdiobus registration fails.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When registering mdiobus children, if we get an -EPROBE_DEFER, we shouldn't
ignore it and continue registering the rest of the mdiobus children. This
would permanently prevent the deferring child mdiobus from working instead
of reattempting it in the future. So, if a child mdiobus needs to be
reattempted in the future, defer the entire mdio-mux initialization.
This fixes the issue where PHYs sitting under the mdio-mux aren't
initialized correctly if the PHY's interrupt controller is not yet ready
when the mdio-mux is being probed. Additional context in the link below.
Fixes: 0ca2997d1452 ("netdev/of/phy: Add MDIO bus multiplexer support.")
Link: https://lore.kernel.org/lkml/CAGETcx95kHrv8wA-O+-JtfH7H9biJEGJtijuPVN0V5dUKUAB3A@mail.gmail.com/#t
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we are seeing memory allocation errors, don't try to continue
registering child mdiobus devices. It's unlikely they'll succeed.
Fixes: 342fa1964439 ("mdio: mux: make child bus walking more permissive and errors more verbose")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The whole point of devm_* APIs is that you don't have to undo them if you
are returning an error that's going to get propagated out of a probe()
function. So delete unnecessary devm_kfree() call in the error return path.
Fixes: b60161668199 ("mdio: mux: Correct mdio_mux_init error path issues")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
or worse
It seems that of_find_compatible_node has a weird calling convention in
which it calls of_node_put() on the "from" node argument, instead of
leaving that up to the caller. This comes from the fact that
of_find_compatible_node with a non-NULL "from" argument it only supposed
to be used as the iterator function of for_each_compatible_node(). OF
iterator functions call of_node_get on the next OF node and of_node_put()
on the previous one.
When of_find_compatible_node calls of_node_put, it actually never
expects the refcount to drop to zero, because the call is done under the
atomic devtree_lock context, and when the refcount drops to zero it
triggers a kobject and a sysfs file deletion, which assume blocking
context.
So any driver call to of_find_compatible_node is probably buggy because
an unexpected of_node_put() takes place.
What should be done is to use the of_get_compatible_child() function.
Fixes: 5a8f09748ee7 ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX")
Link: https://lore.kernel.org/netdev/20210814010139.kzryimmp4rizlznt@skbuf/
Suggested-by: Frank Rowand <frowand.list@gmail.com>
Suggested-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When adding support for using the skb->hash value as the flow hash in CAKE,
I accidentally introduced a logic error that broke the host-only isolation
modes of CAKE (srchost and dsthost keywords). Specifically, the flow_hash
variable should stay initialised to 0 in cake_hash() in pure host-based
hashing mode. Add a check for this before using the skb->hash value as
flow_hash.
Fixes: b0c19ed6088a ("sch_cake: Take advantage of skb->hash where appropriate")
Reported-by: Pete Heist <pete@heistp.net>
Tested-by: Pete Heist <pete@heistp.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No longer required now that userspace can't touch anything that might
need it, and should fix DRM MM operations racing with each other, and
the random hangs/crashes that come with that.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
|
|
Long ago, there had been plans for making use of a bunch of these APIs
from userspace and there's various checks in place to stop misbehaving.
Countless other projects have occurred in the meantime, and the pieces
didn't finish falling into place for that to happen.
They will (hopefully) in the not-too-distant future, but it won't look
quite as insane. The super checks are causing problems right now, and
are going to be removed.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
|
|
I honestly don't even know why... These have never been used.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
|
|
Should fix some initial modeset failures on (at least) Ampere boards.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
|
|
When booted with multiple displays attached, the EFI GOP driver on (at
least) Ampere, can leave DP links powered up that aren't being used to
display anything. This confuses our tracking of SOR routing, with the
likely result being a failed modeset and display engine hang.
Fix this by (ab?)using the DisableLT IED script to power-down the link,
restoring HW to a state the driver expects.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
|
|
Still no GA106 as I don't have HW to verif.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
|
|
The struct pci_dev uses reference counting but zPCI assumed erroneously
that the last reference would always be the local reference after
calling pci_stop_and_remove_bus_device(). This is usually the case but
not how reference counting works and thus inherently fragile.
In fact one case where this causes a NULL pointer dereference when on an
SRIOV device the function 0 was hot unplugged before another function of
the same multi-function device. In this case the second function's
pdev->sriov->dev reference keeps the struct pci_dev of function 0 alive
even after the unplug. This bug was previously hidden by the fact that
we were leaking the struct pci_dev which in turn means that it always
outlived the struct zpci_dev. This was fixed in commit 0b13525c20fe
("s390/pci: fix leak of PCI device structure") exposing the broken
behavior.
Fix this by accounting for the long living reference a struct pci_dev
has to its underlying struct zpci_dev via the zbus->function[] array and
only release that in pcibios_release_device() ensuring that the struct
pci_dev is not left with a dangling reference. This is a minimal fix in
the future it would probably better to use fine grained reference
counting for struct zpci_dev.
Fixes: 05bc1be6db4b2 ("s390/pci: create zPCI bus")
Cc: stable@vger.kernel.org
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Reported as working here:
https://github.com/t-8ch/linux-gigabyte-wmi-driver/issues/1#issuecomment-900263115
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20210817154628.84992-1-linux@weissschuh.net
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
