summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2021-01-04usb: gadget: configfs: Preserve function ordering after bind failureChandana Kishori Chiluveru1-2/+2
When binding the ConfigFS gadget to a UDC, the functions in each configuration are added in list order. However, if usb_add_function() fails, the failed function is put back on its configuration's func_list and purge_configs_funcs() is called to further clean up. purge_configs_funcs() iterates over the configurations and functions in forward order, calling unbind() on each of the previously added functions. But after doing so, each function gets moved to the tail of the configuration's func_list. This results in reshuffling the original order of the functions within a configuration such that the failed function now appears first even though it may have originally appeared in the middle or even end of the list. At this point if the ConfigFS gadget is attempted to re-bind to the UDC, the functions will be added in a different order than intended, with the only recourse being to remove and relink the functions all over again. An example of this as follows: ln -s functions/mass_storage.0 configs/c.1 ln -s functions/ncm.0 configs/c.1 ln -s functions/ffs.adb configs/c.1 # oops, forgot to start adbd echo "<udc device>" > UDC # fails start adbd echo "<udc device>" > UDC # now succeeds, but... # bind order is # "ADB", mass_storage, ncm [30133.118289] configfs-gadget gadget: adding 'Mass Storage Function'/ffffff810af87200 to config 'c'/ffffff817d6a2520 [30133.119875] configfs-gadget gadget: adding 'cdc_network'/ffffff80f48d1a00 to config 'c'/ffffff817d6a2520 [30133.119974] using random self ethernet address [30133.120002] using random host ethernet address [30133.139604] usb0: HOST MAC 3e:27:46:ba:3e:26 [30133.140015] usb0: MAC 6e:28:7e:42:66:6a [30133.140062] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 to config 'c'/ffffff817d6a2520 [30133.140081] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 --> -19 [30133.140098] configfs-gadget gadget: unbind function 'Mass Storage Function'/ffffff810af87200 [30133.140119] configfs-gadget gadget: unbind function 'cdc_network'/ffffff80f48d1a00 [30133.173201] configfs-gadget a600000.dwc3: failed to start g1: -19 [30136.661933] init: starting service 'adbd'... [30136.700126] read descriptors [30136.700413] read strings [30138.574484] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 to config 'c'/ffffff817d6a2520 [30138.575497] configfs-gadget gadget: adding 'Mass Storage Function'/ffffff810af87200 to config 'c'/ffffff817d6a2520 [30138.575554] configfs-gadget gadget: adding 'cdc_network'/ffffff80f48d1a00 to config 'c'/ffffff817d6a2520 [30138.575631] using random self ethernet address [30138.575660] using random host ethernet address [30138.595338] usb0: HOST MAC 2e:cf:43:cd:ca:c8 [30138.597160] usb0: MAC 6a:f0:9f:ee:82:a0 [30138.791490] configfs-gadget gadget: super-speed config #1: c Fix this by reversing the iteration order of the functions in purge_config_funcs() when unbinding them, and adding them back to the config's func_list at the head instead of the tail. This ensures that we unbind and unwind back to the original list order. Fixes: 88af8bbe4ef7 ("usb: gadget: the start of the configfs interface") Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org> Signed-off-by: Jack Pham <jackp@codeaurora.org> Reviewed-by: Peter Chen <peter.chen@nxp.com> Link: https://lore.kernel.org/r/20201229224443.31623-1-jackp@codeaurora.org Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-04usb: gadget: select CONFIG_CRC32Arnd Bergmann1-0/+2
Without crc32 support, this driver fails to link: arm-linux-gnueabi-ld: drivers/usb/gadget/function/f_eem.o: in function `eem_unwrap': f_eem.c:(.text+0x11cc): undefined reference to `crc32_le' arm-linux-gnueabi-ld: drivers/usb/gadget/function/f_ncm.o:f_ncm.c:(.text+0x1e40): more undefined references to `crc32_le' follow Fixes: 6d3865f9d41f ("usb: gadget: NCM: Add transmit multi-frame.") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210103214224.1996535-1-arnd@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-04usb: gadget: core: change the comment for usb_gadget_connectPeter Chen1-2/+1
The pullup does not need to be enabled at below situations: - For platforms which the hardware pullup starts after setting register even they do not see the VBUS. If the pullup is always enabled for these platforms, it will consume more power and break the USB IF compliance tests [1]. - For platforms which need to do BC 1.2 charger detection after seeing the VBUS. Pullup D+ will break the charger detection flow. - For platforms which the system suspend is allowed when the connection with host is there but the bus is not at suspend. For these platforms, it is better to disable pullup when entering the system suspend otherwise the host may confuse the device behavior after controller is in low power mode. Disable pullup is considered as a disconnection event from host side. [1] USB-IF Full and Low Speed Compliance Test Procedure F Back-voltage Testing Section 7.2.1 of the USB specification requires that no device shall supply (source) current on VBUS at its upstream facing port at any time. From VBUS on its upstream facing port, a device may only draw (sink) current. They may not provide power to the pull-up resistor on D+/D- unless VBUS is present (see Section 7.1.5). Signed-off-by: Peter Chen <peter.chen@nxp.com> Link: https://lore.kernel.org/r/20201230051114.21370-1-peter.chen@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-04usb: gadget: configfs: Fix use-after-free issue with udc_nameEddie Hung1-2/+9
There is a use-after-free issue, if access udc_name in function gadget_dev_desc_UDC_store after another context free udc_name in function unregister_gadget. Context 1: gadget_dev_desc_UDC_store()->unregister_gadget()-> free udc_name->set udc_name to NULL Context 2: gadget_dev_desc_UDC_show()-> access udc_name Call trace: dump_backtrace+0x0/0x340 show_stack+0x14/0x1c dump_stack+0xe4/0x134 print_address_description+0x78/0x478 __kasan_report+0x270/0x2ec kasan_report+0x10/0x18 __asan_report_load1_noabort+0x18/0x20 string+0xf4/0x138 vsnprintf+0x428/0x14d0 sprintf+0xe4/0x12c gadget_dev_desc_UDC_show+0x54/0x64 configfs_read_file+0x210/0x3a0 __vfs_read+0xf0/0x49c vfs_read+0x130/0x2b4 SyS_read+0x114/0x208 el0_svc_naked+0x34/0x38 Add mutex_lock to protect this kind of scenario. Signed-off-by: Eddie Hung <eddie.hung@mediatek.com> Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com> Reviewed-by: Peter Chen <peter.chen@nxp.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/1609239215-21819-1-git-send-email-macpaul.lin@mediatek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-04usb: dwc3: gadget: Restart DWC3 gadget when enabling pullupWesley Cheng1-11/+3
usb_gadget_deactivate/usb_gadget_activate does not execute the UDC start operation, which may leave EP0 disabled and event IRQs disabled when re-activating the function. Move the enabling/disabling of USB EP0 and device event IRQs to be performed in the pullup routine. Fixes: ae7e86108b12 ("usb: dwc3: Stop active transfers before halting the controller") Tested-by: Michael Tretter <m.tretter@pengutronix.de> Cc: stable <stable@vger.kernel.org> Reported-by: Michael Tretter <m.tretter@pengutronix.de> Signed-off-by: Wesley Cheng <wcheng@codeaurora.org> Link: https://lore.kernel.org/r/1609282837-21666-1-git-send-email-wcheng@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-04usb: usbip: vhci_hcd: protect shift sizeRandy Dunlap1-0/+2
Fix shift out-of-bounds in vhci_hcd.c: UBSAN: shift-out-of-bounds in ../drivers/usb/usbip/vhci_hcd.c:399:41 shift exponent 768 is too large for 32-bit type 'int' Fixes: 03cd00d538a6 ("usbip: vhci-hcd: Set the vhci structure up to work") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: syzbot+297d20e437b79283bf6d@syzkaller.appspotmail.com Cc: Yuyang Du <yuyang.du@intel.com> Cc: Shuah Khan <shuahkh@osg.samsung.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-usb@vger.kernel.org Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201229071309.18418-1-rdunlap@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-04USB: usblp: fix DMA to stackJohan Hovold1-2/+19
Stack-allocated buffers cannot be used for DMA (on all architectures). Replace the HP-channel macro with a helper function that allocates a dedicated transfer buffer so that it can continue to be used with arguments from the stack. Note that the buffer is cleared on allocation as usblp_ctrl_msg() returns success also on short transfers (the buffer is only used for debugging). Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20210104145302.2087-1-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-30USB: Gadget: dummy-hcd: Fix shift-out-of-bounds bugAlan Stern1-12/+23
The dummy-hcd driver was written under the assumption that all the parameters in URBs sent to its root hub would be valid. With URBs sent from userspace via usbfs, that assumption can be violated. In particular, the driver doesn't fully check the port-feature values stored in the wValue entry of Clear-Port-Feature and Set-Port-Feature requests. Values that are too large can cause the driver to perform an invalid left shift of more than 32 bits. Ironically, two of those left shifts are unnecessary, because they implement Set-Port-Feature requests that hubs are not required to support, according to section 11.24.2.13 of the USB-2.0 spec. This patch adds the appropriate checks for the port feature selector values and removes the unnecessary feature settings. It also rejects requests to set the TEST feature or to set or clear the INDICATOR and C_OVERCURRENT features, as none of these are relevant to dummy-hcd's root-hub emulation. CC: <stable@vger.kernel.org> Reported-and-tested-by: syzbot+5925509f78293baa7331@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20201230162044.GA727759@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: gadget: f_uac2: reset wMaxPacketSizeJerome Brunet1-14/+55
With commit 913e4a90b6f9 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth") wMaxPacketSize is computed dynamically but the value is never reset. Because of this, the actual maximum packet size can only decrease each time the audio gadget is instantiated. Reset the endpoint maximum packet size and mark wMaxPacketSize as dynamic to solve the problem. Fixes: 913e4a90b6f9 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201221173531.215169-2-jbrunet@baylibre.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend regressionSerge Semin1-13/+5
First of all the commit e0082698b689 ("usb: dwc3: ulpi: conditionally resume ULPI PHY") introduced the Suspend USB2.0 HS/FS/LS PHY regression, as by design of the fix any attempt to read/write from/to the PHY control registers will completely disable the PHY suspension, which consequently will increase the USB bus power consumption. Secondly the fix won't work well for the very first attempt of the ULPI PHY control registers IO, because after disabling the USB2.0 PHY suspension functionality it will still take some time for the bus to resume from the sleep state if one has been reached before it. So the very first PHY register read/write operation will take more time than the busy-loop provides and the IO timeout error might be returned anyway. Here we suggest to fix the denoted problems in the following way. First of all let's not disable the Suspend USB2.0 HS/FS/LS PHY functionality so to make the controller and the USB2.0 bus more power efficient. Secondly instead of that we'll extend the PHY IO op wait procedure with 1 - 1.2 ms sleep if the PHY suspension is enabled (1ms should be enough as by LPM specification it is at most how long it takes for the USB2.0 bus to resume from L1 (Sleep) state). Finally in case if the USB2.0 PHY suspension functionality has been disabled on the DWC USB3 controller setup procedure we'll compensate the USB bus resume process latency by extending the busy-loop attempts counter. Fixes: e0082698b689 ("usb: dwc3: ulpi: conditionally resume ULPI PHY") Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20201210085008.13264-4-Sergey.Semin@baikalelectronics.ru Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: dwc3: ulpi: Replace CPU-based busyloop with Protocol-based oneSerge Semin1-3/+15
Originally the procedure of the ULPI transaction finish detection has been developed as a simple busy-loop with just decrementing counter and no delays. It's wrong since on different systems the loop will take a different time to complete. So if the system bus and CPU are fast enough to overtake the ULPI bus and the companion PHY reaction, then we'll get to take a false timeout error. Fix this by converting the busy-loop procedure to take the standard bus speed, address value and the registers access mode into account for the busy-loop delay calculation. Here is the way the fix works. It's known that the ULPI bus is clocked with 60MHz signal. In accordance with [1] the ULPI bus protocol is created so to spend 5 and 6 clock periods for immediate register write and read operations respectively, and 6 and 7 clock periods - for the extended register writes and reads. Based on that we can easily pre-calculate the time which will be needed for the controller to perform a requested IO operation. Note we'll still preserve the attempts counter in case if the DWC USB3 controller has got some internals delays. [1] UTMI+ Low Pin Interface (ULPI) Specification, Revision 1.1, October 20, 2004, pp. 30 - 36. Fixes: 88bc9d194ff6 ("usb: dwc3: add ULPI interface support") Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20201210085008.13264-3-Sergey.Semin@baikalelectronics.ru Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: dwc3: ulpi: Use VStsDone to detect PHY regs access completionSerge Semin2-1/+2
In accordance with [1] the DWC_usb3 core sets the GUSB2PHYACCn.VStsDone bit when the PHY vendor control access is done and clears it when the application initiates a new transaction. The doc doesn't say anything about the GUSB2PHYACCn.VStsBsy flag serving for the same purpose. Moreover we've discovered that the VStsBsy flag can be cleared before the VStsDone bit. So using the former as a signal of the PHY control registers completion might be dangerous. Let's have the VStsDone flag utilized instead then. [1] Synopsys DesignWare Cores SuperSpeed USB 3.0 xHCI Host Controller Databook, 2.70a, December 2013, p.388 Fixes: 88bc9d194ff6 ("usb: dwc3: add ULPI interface support") Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20201210085008.13264-2-Sergey.Semin@baikalelectronics.ru Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28USB: yurex: fix control-URB timeout handlingJohan Hovold1-0/+3
Make sure to always cancel the control URB in write() so that it can be reused after a timeout or spurious CMD_ACK. Currently any further write requests after a timeout would fail after triggering a WARN() in usb_submit_urb() when attempting to submit the already active URB. Reported-by: syzbot+e87ebe0f7913f71f2ea5@syzkaller.appspotmail.com Fixes: 6bc235a2e24a ("USB: add driver for Meywa-Denki & Kayac YUREX") Cc: stable <stable@vger.kernel.org> # 2.6.37 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: chipidea: ci_hdrc_imx: add missing put_device() call in ↵Yu Kuai1-1/+5
usbmisc_get_init_data() if of_find_device_by_node() succeed, usbmisc_get_init_data() doesn't have a corresponding put_device(). Thus add put_device() to fix the exception handling for this function implementation. Fixes: ef12da914ed6 ("usb: chipidea: imx: properly check for usbmisc") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201117011430.642589-1-yukuai3@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: gadget: u_ether: Fix MTU size mismatch with RX packet sizeManish Narani1-4/+5
Fix the MTU size issue with RX packet size as the host sends the packet with extra bytes containing ethernet header. This causes failure when user sets the MTU size to the maximum i.e. 15412. In this case the ethernet packet received will be of length 15412 plus the ethernet header length. This patch fixes the issue where there is a check that RX packet length must not be more than max packet length. Fixes: bba787a860fa ("usb: gadget: ether: Allow jumbo frames") Signed-off-by: Manish Narani <manish.narani@xilinx.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1605597215-122027-1-git-send-email-manish.narani@xilinx.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28USB: gadget: legacy: fix return error code in acm_ms_bind()Yang Yingliang1-1/+3
If usb_otg_descriptor_alloc() failed, it need return ENOMEM. Fixes: 578aa8a2b12c ("usb: gadget: acm_ms: allocate and init otg descriptor by otg capabilities") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201117092955.4102785-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: gadget: Fix spinlock lockup on usb_function_deactivateSriharsha Allenki1-2/+8
There is a spinlock lockup as part of composite_disconnect when it tries to acquire cdev->lock as part of usb_gadget_deactivate. This is because the usb_gadget_deactivate is called from usb_function_deactivate with the same spinlock held. This would result in the below call stack and leads to stall. rcu: INFO: rcu_preempt detected stalls on CPUs/tasks: rcu: 3-...0: (1 GPs behind) idle=162/1/0x4000000000000000 softirq=10819/10819 fqs=2356 (detected by 2, t=5252 jiffies, g=20129, q=3770) Task dump for CPU 3: task:uvc-gadget_wlhe state:R running task stack: 0 pid: 674 ppid: 636 flags:0x00000202 Call trace: __switch_to+0xc0/0x170 _raw_spin_lock_irqsave+0x84/0xb0 composite_disconnect+0x28/0x78 configfs_composite_disconnect+0x68/0x70 usb_gadget_disconnect+0x10c/0x128 usb_gadget_deactivate+0xd4/0x108 usb_function_deactivate+0x6c/0x80 uvc_function_disconnect+0x20/0x58 uvc_v4l2_release+0x30/0x88 v4l2_release+0xbc/0xf0 __fput+0x7c/0x230 ____fput+0x14/0x20 task_work_run+0x88/0x140 do_notify_resume+0x240/0x6f0 work_pending+0x8/0x200 Fix this by doing an unlock on cdev->lock before the usb_gadget_deactivate call from usb_function_deactivate. The same lockup can happen in the usb_gadget_activate path. Fix that path as well. Reported-by: Peter Chen <peter.chen@nxp.com> Link: https://lore.kernel.org/linux-usb/20201102094936.GA29581@b29397-desktop/ Tested-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201202130220.24926-1-sallenki@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: gadget: function: printer: Fix a memory leak for interface descriptorZqiang1-0/+1
When printer driver is loaded, the printer_func_bind function is called, in this function, the interface descriptor be allocated memory, if after that, the error occurred, the interface descriptor memory need to be free. Reviewed-by: Peter Chen <peter.chen@nxp.com> Cc: <stable@vger.kernel.org> Signed-off-by: Zqiang <qiang.zhang@windriver.com> Link: https://lore.kernel.org/r/20201210020148.6691-1-qiang.zhang@windriver.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: dwc3: meson-g12a: disable clk on error handling path in probeZheng Zengkai1-1/+1
dwc3_meson_g12a_probe() does not invoke clk_bulk_disable_unprepare() on one error handling path. This patch fixes that. Fixes: 347052e3bf1b ("usb: dwc3: meson-g12a: fix USB2 PHY initialization on G12A and A1 SoCs") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com> Cc: stable <stable@vger.kernel.org> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20201215025459.91794-1-zhengzengkai@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28USB: xhci: fix U1/U2 handling for hardware with XHCI_INTEL_HOST quirk setMichael Grzeschik1-12/+12
The commit 0472bf06c6fd ("xhci: Prevent U1/U2 link pm states if exit latency is too long") was constraining the xhci code not to allow U1/U2 sleep states if the latency to wake up from the U-states reached the service interval of an periodic endpoint. This fix was not taking into account that in case the quirk XHCI_INTEL_HOST is set, the wakeup time will be calculated and configured differently. It checks for u1_params.mel/u2_params.mel as a limit. But the code could decide to write another MEL into the hardware. This leads to broken cases where not enough bandwidth is available for other devices: usb 1-2: can't set config #1, error -28 This patch is fixing that case by checking for timeout_ns after the wakeup time was calculated depending on the quirks. Fixes: 0472bf06c6fd ("xhci: Prevent U1/U2 link pm states if exit latency is too long") Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201215193147.11738-1-m.grzeschik@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: typec: intel_pmc_mux: Configure HPD first for HPD+IRQ requestMadhusudanarao Amara1-0/+11
Warm reboot scenarios some times type C Mux driver gets Mux configuration request as HPD=1,IRQ=1. In that scenario typeC Mux driver need to configure Mux as follows as per IOM requirement: (1). Confgiure Mux HPD = 1, IRQ = 0 (2). Configure Mux with HPD = 1, IRQ = 1 IOM expects TypeC Mux configuration as follows: (1). HPD=1, IRQ=0 (2). HPD=1, IRQ=1 if IOM gets mux config request (2) without configuring (1), it will ignore the request. The impact of this is there is no DP_alt mode display. Fixes: 43d596e32276 ("usb: typec: intel_pmc_mux: Check the port status before connect") Cc: stable@vger.kernel.org Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com> Link: https://lore.kernel.org/r/20201216140918.49197-1-madhusudanarao.amara@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28USB: cdc-wdm: Fix use after free in service_outstanding_interrupt().Tetsuo Handa1-3/+13
syzbot is reporting UAF at usb_submit_urb() [1], for service_outstanding_interrupt() is not checking WDM_DISCONNECTING before calling usb_submit_urb(). Close the race by doing same checks wdm_read() does upon retry. Also, while wdm_read() checks WDM_DISCONNECTING with desc->rlock held, service_interrupt_work() does not hold desc->rlock. Thus, it is possible that usb_submit_urb() is called from service_outstanding_interrupt() from service_interrupt_work() after WDM_DISCONNECTING was set and kill_urbs() from wdm_disconnect() completed. Thus, move kill_urbs() in wdm_disconnect() to after cancel_work_sync() (which makes sure that service_interrupt_work() is no longer running) completed. Although it seems to be safe to dereference desc->intf->dev in service_outstanding_interrupt() even if WDM_DISCONNECTING was already set because desc->rlock or cancel_work_sync() prevents wdm_disconnect() from reaching list_del() before service_outstanding_interrupt() completes, let's not emit error message if WDM_DISCONNECTING is set by wdm_disconnect() while usb_submit_urb() is in progress. [1] https://syzkaller.appspot.com/bug?extid=9e04e2df4a32fb661daf Reported-by: syzbot <syzbot+9e04e2df4a32fb661daf@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/620e2ee0-b9a3-dbda-a25b-a93e0ed03ec5@i-love.sakura.ne.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: gadget: fsl_mxc_udc: Remove the driverFabio Estevam3-124/+1
Since 5.10-rc1 i.MX is a devicetree-only platform, and this driver was only used by the old non-DT i.MX devices. Remove the driver as it has no users left. Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Peter Chen <peter.chen@nxp.com> Link: https://lore.kernel.org/r/20201210210413.15262-1-festevam@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28dt-bindings: usb: Add new compatible string for AM64 SoCAswath Govindraju1-1/+5
Add compatible string in j721e-usb binding file as the same USB subsystem is present in AM64. Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Link: https://lore.kernel.org/r/20201215042549.7956-1-a-govindraju@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28MAINTAINERS: Update address for Cadence USB3 driverRoger Quadros1-1/+1
Updates my email address for Cadence USB3 driver. Signed-off-by: Roger Quadros <rogerq@ti.com> Link: https://lore.kernel.org/r/20201218105736.17667-1-rogerq@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28USB: cdc-acm: blacklist another IR Droid deviceSean Young1-0/+4
This device is supported by the IR Toy driver. Reported-by: Georgi Bakalski <georgi.bakalski@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Acked-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201227134502.4548-2-sean@mess.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-27Linux 5.11-rc1v5.11-rc1Linus Torvalds1-2/+2
2020-12-27proc mountinfo: make splice available againLinus Torvalds1-3/+6
Since commit 36e2c7421f02 ("fs: don't allow splice read/write without explicit ops") we've required that file operation structures explicitly enable splice support, rather than falling back to the default handlers. Most /proc files use the indirect 'struct proc_ops' to describe their file operations, and were fixed up to support splice earlier in commits 40be821d627c..b24c30c67863, but the mountinfo files interact with the VFS directly using their own 'struct file_operations' and got missed as a result. This adds the necessary support for splice to work for /proc/*/mountinfo and friends. Reported-by: Joan Bruguera Micó <joanbrugueram@gmail.com> Reported-by: Jussi Kivilinna <jussi.kivilinna@iki.fi> Link: https://bugzilla.kernel.org/show_bug.cgi?id=209971 Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-27Merge tag 'ntb-5.11' of git://github.com/jonmason/ntbLinus Torvalds4-3/+44
Pull NTB fixes from Jon Mason: "Bug fix for IDT NTB and Intel NTB LTR management support" * tag 'ntb-5.11' of git://github.com/jonmason/ntb: ntb: intel: add Intel NTB LTR vendor support for gen4 NTB ntb: idt: fix error check in ntb_hw_idt.c
2020-12-27Merge branch 'linus' of ↵Linus Torvalds2-2/+4
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 Pull crypto fixes from Herbert Xu: "Fix a number of autobuild failures due to missing Kconfig dependencies" * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: qat - add CRYPTO_AES to Kconfig dependencies crypto: keembay - Add dependency on HAS_IOMEM crypto: keembay - CRYPTO_DEV_KEEMBAY_OCS_AES_SM4 should depend on ARCH_KEEMBAY
2020-12-27Merge tag 'objtool-urgent-2020-12-27' of ↵Linus Torvalds4-26/+42
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull objtool fix from Ingo Molnar: "Fix a segfault that occurs when built with Clang" * tag 'objtool-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: objtool: Fix seg fault with Clang non-section symbols
2020-12-27Merge tag 'locking-urgent-2020-12-27' of ↵Linus Torvalds3-4/+22
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull locking fixes from Ingo Molnar: "Misc fixes/updates: - Fix static keys usage in module __init sections - Add separate MAINTAINERS entry for static branches/calls - Fix lockdep splat with CONFIG_PREEMPTIRQ_EVENTS=y tracing" * tag 'locking-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: softirq: Avoid bad tracing / lockdep interaction jump_label/static_call: Add MAINTAINERS jump_label: Fix usage in module __init
2020-12-27Merge tag 'timers-urgent-2020-12-27' of ↵Linus Torvalds3-15/+4
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull timer fixes from Ingo Molnar: "Update/fix two CPU sanity checks in the hotplug and the boot code, and fix a typo in the Kconfig help text. [ Context: the first two commits are the result of an ongoing annotation+review work of (intentional) tick_do_timer_cpu() data races reported by KCSAN, but the annotations aren't fully cooked yet ]" * tag 'timers-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: timekeeping: Fix spelling mistake in Kconfig "fullfill" -> "fulfill" tick/sched: Remove bogus boot "safety" check tick: Remove pointless cpu valid check in hotplug code
2020-12-27Merge tag 'sched-urgent-2020-12-27' of ↵Linus Torvalds2-33/+20
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull scheduler fix from Ingo Molnar: "Fix a context switch performance regression" * tag 'sched-urgent-2020-12-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched: Optimize finish_lock_switch()
2020-12-26mfd: ab8500-debugfs: Remove extraneous seq_putcLinus Torvalds1-1/+0
Commit c9a3c4e637ac ("mfd: ab8500-debugfs: Remove extraneous curly brace") removed a left-over curly brace that caused build failures, but Joe Perches points out that the subsequent 'seq_putc()' should also be removed, because the commit that caused all these problems already added the final '\n' to the seq_printf() above it. Reported-by: Joe Perches <joe@perches.com> Fixes: 886c8121659d ("mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc") Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-25Merge tag 'pci-v5.11-fixes-1' of ↵Linus Torvalds2-32/+31
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI fixes from Bjorn Helgaas: - Fix a tegra enumeration regression (Rob Herring) - Fix a designware-host check that warned on *success*, not failure (Alexander Lobakin) * tag 'pci-v5.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI: dwc: Fix inverted condition of DMA mask setup warning PCI: tegra: Fix host link initialization
2020-12-25mfd: ab8500-debugfs: Remove extraneous curly braceNathan Chancellor1-1/+0
Clang errors: drivers/mfd/ab8500-debugfs.c:1526:2: error: non-void function does not return a value [-Werror,-Wreturn-type] } ^ drivers/mfd/ab8500-debugfs.c:1528:2: error: expected identifier or '(' return 0; ^ drivers/mfd/ab8500-debugfs.c:1529:1: error: extraneous closing brace ('}') } ^ 3 errors generated. The cleanup in ab8500_interrupts_show left a curly brace around, remove it to fix the error. Fixes: 886c8121659d ("mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc") Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-25PCI: dwc: Fix inverted condition of DMA mask setup warningAlexander Lobakin1-6/+2
Commit 660c486590aa ("PCI: dwc: Set 32-bit DMA mask for MSI target address allocation") added dma_mask_set() call to explicitly set 32-bit DMA mask for MSI message mapping, but for now it throws a warning on ret == 0, while dma_set_mask() returns 0 in case of success. Fix this by inverting the condition. [bhelgaas: join string to make it greppable] Fixes: 660c486590aa ("PCI: dwc: Set 32-bit DMA mask for MSI target address allocation") Link: https://lore.kernel.org/r/20201222150708.67983-1-alobakin@pm.me Signed-off-by: Alexander Lobakin <alobakin@pm.me> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2020-12-25PCI: tegra: Fix host link initializationRob Herring1-26/+29
Commit b9ac0f9dc8ea ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common code") broke enumeration of downstream devices on Tegra: In non-working case (next-20201211): 0001:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad2 (rev a1) 0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13) 0005:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad0 (rev a1) In working case (v5.10-rc7): 0001:00:00.0 PCI bridge: Molex Incorporated Device 1ad2 (rev a1) 0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13) 0005:00:00.0 PCI bridge: Molex Incorporated Device 1ad0 (rev a1) 0005:01:00.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab) 0005:02:02.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab) 0005:03:00.0 USB controller: PLX Technology, Inc. Device 3380 (rev ab) The problem seems to be dw_pcie_setup_rc() is now called twice before and after the link up handling. The fix is to move Tegra's link up handling to .start_link() function like other DWC drivers. Tegra is a bit more complicated than others as it re-inits the whole DWC controller to retry the link. With this, the initialization ordering is restored to match the prior sequence. Fixes: b9ac0f9dc8ea ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common code") Link: https://lore.kernel.org/r/20201218143905.1614098-1-robh@kernel.org Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de> Tested-by: Mian Yousaf Kaukab <ykaukab@suse.de> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Vidya Sagar <vidyas@nvidia.com>
2020-12-25drm/amd/display: avoid uninitialized variable warningLinus Torvalds1-1/+1
clang (quite rightly) complains fairly loudly about the newly added mpc1_get_mpc_out_mux() function returning an uninitialized value if the 'opp_id' checks don't pass. This may not happen in practice, but the code really shouldn't return garbage if the sanity checks don't pass. So just initialize 'val' to zero to avoid the issue. Fixes: 110b055b2827 ("drm/amd/display: add getter routine to retrieve mpcc mux") Cc: Josip Pavic <Josip.Pavic@amd.com> Cc: Bindu Ramamurthy <bindu.r@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-25Merge tag 'perf-tools-2020-12-24' of ↵Linus Torvalds23-391/+688
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux Pull more perf tools updates from Arnaldo Carvalho de Melo: - Refactor 'perf stat' per CPU/socket/die/thread aggregation fixing use cases in ARM machines. - Fix memory leak when synthesizing SDT probes in 'perf probe'. - Update kernel header copies related to KVM, epol_pwait. msr-index and powerpc and s390 syscall tables. * tag 'perf-tools-2020-12-24' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (24 commits) perf probe: Fix memory leak when synthesizing SDT probes perf stat aggregation: Add separate thread member perf stat aggregation: Add separate core member perf stat aggregation: Add separate die member perf stat aggregation: Add separate socket member perf stat aggregation: Add separate node member perf stat aggregation: Start using cpu_aggr_id in map perf cpumap: Drop in cpu_aggr_map struct perf cpumap: Add new map type for aggregation perf stat: Replace aggregation ID with a struct perf cpumap: Add new struct for cpu aggregation perf cpumap: Use existing allocator to avoid using malloc perf tests: Improve topology test to check all aggregation types perf tools: Update s390's syscall.tbl copy from the kernel sources perf tools: Update powerpc's syscall.tbl copy from the kernel sources perf s390: Move syscall.tbl check into check-headers.sh perf powerpc: Move syscall.tbl check to check-headers.sh tools headers UAPI: Synch KVM's svm.h header with the kernel tools kvm headers: Update KVM headers from the kernel sources tools headers UAPI: Sync KVM's vmx.h header with the kernel sources ...
2020-12-25Merge branch 'for-5.11' of ↵Linus Torvalds5-306/+20
git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux Pull coccinelle updates from Julia Lawall. * 'for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux: scripts: coccicheck: Correct usage of make coccicheck coccinelle: update expiring email addresses coccinnelle: Remove ptr_ret script kbuild: do not use scripts/ld-version.sh for checking spatch version remove boolinit.cocci
2020-12-25genirq: Fix export of irq_to_desc() for powerpc KVMMichael Ellerman1-1/+1
Commit 64a1b95bb9fe ("genirq: Restrict export of irq_to_desc()") removed the export of irq_to_desc() unless powerpc KVM is being built, because there is still a use of irq_to_desc() in modular code there. However it used: #ifdef CONFIG_KVM_BOOK3S_64_HV Which doesn't work when that symbol is =m, leading to a build failure: ERROR: modpost: "irq_to_desc" [arch/powerpc/kvm/kvm-hv.ko] undefined! Fix it by checking for the definedness of the correct symbol which is CONFIG_KVM_BOOK3S_64_HV_MODULE. Fixes: 64a1b95bb9fe ("genirq: Restrict export of irq_to_desc()") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-25Merge branch 'work.misc' of ↵Linus Torvalds7-10/+23
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull misc vfs updates from Al Viro: "Assorted patches from previous cycle(s)..." * 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: fix hostfs_open() use of ->f_path.dentry Make sure that make_create_in_sticky() never sees uninitialized value of dir_mode fs: Kill DCACHE_DONTCACHE dentry even if DCACHE_REFERENCED is set fs: Handle I_DONTCACHE in iput_final() instead of generic_drop_inode() fs/namespace.c: WARN if mnt_count has become negative
2020-12-24Merge tag 'docs-5.11-2' of git://git.lwn.net/linuxLinus Torvalds3-14/+20
Pull documentation fixes from Jonathan Corbet: "A small set of late-arriving, small documentation fixes" * tag 'docs-5.11-2' of git://git.lwn.net/linux: docs: admin-guide: Fix default value of max_map_count in sysctl/vm.rst Documentation/submitting-patches: Document the SoB chain Documentation: process: Correct numbering docs: submitting-patches: Trivial - fix grammatical error
2020-12-24Merge tag 'ext4_for_linus' of ↵Linus Torvalds19-378/+504
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4 Pull ext4 updates from Ted Ts'o: "Various bug fixes and cleanups for ext4; no new features this cycle" * tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (29 commits) ext4: remove unnecessary wbc parameter from ext4_bio_write_page ext4: avoid s_mb_prefetch to be zero in individual scenarios ext4: defer saving error info from atomic context ext4: simplify ext4 error translation ext4: move functions in super.c ext4: make ext4_abort() use __ext4_error() ext4: standardize error message in ext4_protect_reserved_inode() ext4: remove redundant sb checksum recomputation ext4: don't remount read-only with errors=continue on reboot ext4: fix deadlock with fs freezing and EA inodes jbd2: add a helper to find out number of fast commit blocks ext4: make fast_commit.h byte identical with e2fsprogs/fast_commit.h ext4: fix fall-through warnings for Clang ext4: add docs about fast commit idempotence ext4: remove the unused EXT4_CURRENT_REV macro ext4: fix an IS_ERR() vs NULL check ext4: check for invalid block size early when mounting a file system ext4: fix a memory leak of ext4_free_data ext4: delete nonsensical (commented-out) code inside ext4_xattr_block_set() ext4: update ext4_data_block_valid related comments ...
2020-12-24Merge tag 'Smack-for-5.11-io_uring-fix' of ↵Linus Torvalds1-2/+3
git://github.com/cschaufler/smack-next Pull smack fix from Casey Schaufler: "Provide a fix for the incorrect handling of privilege in the face of io_uring's use of kernel threads. That invalidated an long standing assumption regarding the privilege of kernel threads. The fix is simple and safe. It was provided by Jens Axboe and has been tested" * tag 'Smack-for-5.11-io_uring-fix' of git://github.com/cschaufler/smack-next: Smack: Handle io_uring kernel thread privileges
2020-12-24Merge tag 'riscv-for-linus-5.11-rc1' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux Pull RISC-V fix from Palmer Dabbelt "Avoid trying to initialize memory regions outside the usable range" * tag 'riscv-for-linus-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: RISC-V: Fix usage of memblock_enforce_memory_limit
2020-12-24Merge tag 'powerpc-5.11-2' of ↵Linus Torvalds7-15/+29
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fixes from Michael Ellerman: - Four commits fixing various things in the new C VDSO code - One fix for a 32-bit VMAP stack bug - Two minor build fixes Thanks to Cédric Le Goater, Christophe Leroy, and Will Springer. * tag 'powerpc-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/32: Fix vmap stack - Properly set r1 before activating MMU on syscall too powerpc/vdso: Fix DOTSYM for 32-bit LE VDSO powerpc/vdso: Don't pass 64-bit ABI cflags to 32-bit VDSO powerpc/vdso: Block R_PPC_REL24 relocations powerpc/smp: Add __init to init_big_cores() powerpc/time: Force inlining of get_tb() powerpc/boot: Fix build of dts/fsl
2020-12-24Merge tag 'irq-core-2020-12-23' of ↵Linus Torvalds32-228/+281
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull irq updates from Thomas Gleixner: "This is the second attempt after the first one failed miserably and got zapped to unblock the rest of the interrupt related patches. A treewide cleanup of interrupt descriptor (ab)use with all sorts of racy accesses, inefficient and disfunctional code. The goal is to remove the export of irq_to_desc() to prevent these things from creeping up again" * tag 'irq-core-2020-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (30 commits) genirq: Restrict export of irq_to_desc() xen/events: Implement irq distribution xen/events: Reduce irq_info:: Spurious_cnt storage size xen/events: Only force affinity mask for percpu interrupts xen/events: Use immediate affinity setting xen/events: Remove disfunct affinity spreading xen/events: Remove unused bind_evtchn_to_irq_lateeoi() net/mlx5: Use effective interrupt affinity net/mlx5: Replace irq_to_desc() abuse net/mlx4: Use effective interrupt affinity net/mlx4: Replace irq_to_desc() abuse PCI: mobiveil: Use irq_data_get_irq_chip_data() PCI: xilinx-nwl: Use irq_data_get_irq_chip_data() NTB/msi: Use irq_has_action() mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc pinctrl: nomadik: Use irq_has_action() drm/i915/pmu: Replace open coded kstat_irqs() copy drm/i915/lpe_audio: Remove pointless irq_to_desc() usage s390/irq: Use irq_desc_kstat_cpu() in show_msi_interrupt() parisc/irq: Use irq_desc_kstat_cpu() in show_interrupts() ...
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-31 16:02:28 +0000