| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Drop 'S' from end of CONFIG_MPTCP_KUNIT_TESTS in order to adhere to the
KUNIT *_KUNIT_TEST config name format.
Fixes: a00a582203db (mptcp: move crypto test to KUNIT)
Reviewed-by: David Gow <davidgow@google.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Nico Pache <npache@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vladimir Oltean says:
====================
Fixups for XDP on NXP ENETC
After some more XDP testing on the NXP LS1028A, this is a set of 10 bug
fixes, simplifications and tweaks, ranging from addressing Toke's feedback
(the network stack can run concurrently with XDP on the same TX rings)
to fixing some OOM conditions seen under TX congestion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Described in fd5736bf9f23 ("enetc: Workaround for MDIO register access
issue") is a workaround for a hardware bug that requires a register
access of the MDIO controller to never happen concurrently with a
register access of a port PF. To avoid that, a mutual exclusion scheme
with rwlocks was implemented - the port PF accessors are the 'read'
side, and the MDIO accessors are the 'write' side.
When we do XDP_REDIRECT between two ENETC interfaces, all is fine
because the MDIO lock is already taken from the NAPI poll loop.
But when the ingress interface is not ENETC, just the egress is, the
MDIO lock is not taken, so we might access the port PF registers
concurrently with MDIO, which will make the link flap due to wrong
values returned from the PHY.
To avoid this, let's just slap an enetc_lock_mdio/enetc_unlock_mdio at
the beginning and ending of enetc_xdp_xmit. The fact that the MDIO lock
is designed as a rwlock is important here, because the read side is
reentrant (that is one of the main reasons why we chose it). Usually,
the way we benefit of its reentrancy is by running the data path
concurrently on both CPUs, but in this case, we benefit from the
reentrancy by taking the lock even when the lock is already taken
(and that's the situation where ENETC is both the ingress and the egress
interface for XDP_REDIRECT, which was fine before and still is fine now).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the TX ring is congested, enetc_xdp_tx() returns false for the
current XDP frame (represented as an array of software BDs).
This array of software TX BDs is constructed in enetc_rx_swbd_to_xdp_tx_swbd
from software BDs freshly cleaned from the RX ring. The issue is that we
scrub the RX software BDs too soon, more precisely before we know that
we can enqueue the TX BDs successfully into the TX ring.
If we can't enqueue them (and enetc_xdp_tx returns false), we call
enetc_xdp_drop which attempts to recycle the buffers held by the RX
software BDs. But because we scrubbed those RX BDs already, two things
happen:
(a) we leak their memory
(b) we populate the RX software BD ring with an all-zero rx_swbd
structure, which makes the buffer refill path allocate more memory.
enetc_refill_rx_ring
-> if (unlikely(!rx_swbd->page))
-> enetc_new_page
That is a recipe for fast OOM.
Fixes: 7ed2bc80074e ("net: enetc: add support for XDP_TX")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the XDP program returns an invalid action, we should free the RX
buffer.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible for one CPU to perform TX hashing (see netdev_pick_tx)
between the 8 ENETC TX rings, and the TX hashing to select TX queue 1.
At the same time, it is possible for the other CPU to already use TX
ring 1 for XDP (either XDP_TX or XDP_REDIRECT). Since there is no mutual
exclusion between XDP and the network stack, we run into an issue
because the ENETC TX procedure is not reentrant.
The obvious approach would be to just make XDP take the lock of the
network stack's TX queue corresponding to the ring it's about to enqueue
in.
For XDP_REDIRECT, this is quite straightforward, a lock at the beginning
and end of enetc_xdp_xmit() should do the trick.
But for XDP_TX, it's a bit more complicated. For one, we do TX batching
all by ourselves for frames with the XDP_TX verdict. This is something
we would like to keep the way it is, for performance reasons. But
batching means that the network stack's lock should be kept from the
first enqueued XDP_TX frame and until we ring the doorbell. That is
mostly fine, except for cases when in the same NAPI loop we have mixed
XDP_TX and XDP_REDIRECT frames. So if enetc_xdp_xmit() gets called while
we are holding the lock from the RX NAPI, then bam, deadlock. The naive
answer could be 'just flush the XDP_TX frames first, then release the
network stack's TX queue lock, then call xdp_do_flush_map()'. But even
xdp_do_redirect() is capable of flushing the batched XDP_REDIRECT
frames, so unless we unlock/relock the TX queue around xdp_do_redirect(),
there simply isn't any clean way to protect XDP_TX from concurrent
network stack .ndo_start_xmit() on another CPU.
So we need to take a different approach, and that is to reserve two
rings for the sole use of XDP. We leave TX rings
0..ndev->real_num_tx_queues-1 to be handled by the network stack, and we
pick them from the end of the priv->tx_ring array.
We make an effort to keep the mapping done by enetc_alloc_msix() which
decides which CPU handles the TX completions of which TX ring in its
NAPI poll. So the XDP TX ring of CPU 0 is handled by TX ring 6, and the
XDP TX ring of CPU 1 is handled by TX ring 7.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that commit d6a2829e82cf ("net: enetc: increase RX ring default
size") has increased the RX ring size, it is quite easy to congest the
TX rings when the traffic is predominantly XDP_TX, as the RX ring is
quite a bit larger than the TX one.
Since we bit the bullet and did the expensive thing already (larger RX
rings consume more memory pages), it seems quite foolish to keep the TX
rings small. So make them equally sized with TX.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xdp_do_redirect already contains:
-> dev_map_enqueue
-> __xdp_enqueue
-> bq_enqueue
-> bq_xmit_all // if we have more than 16 frames
So the logic from enetc will never be hit, because ENETC_DEFAULT_TX_WORK
is 128.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the code path below fails:
enetc_clean_rx_ring_xdp // XDP_PASS
-> enetc_build_skb
-> enetc_map_rx_buff_to_skb
-> build_skb
enetc_clean_rx_ring_xdp will 'break', but that 'break' instruction isn't
strong enough to actually break the NAPI poll loop, just the switch/case
statement for XDP actions. So we increment rx_frm_cnt and go to the next
frames minding our own business.
Instead let's do what the skb NAPI poll function does, and break the
loop now, waiting for the memory pressure to go away. Otherwise the next
calls to build_skb() are likely to fail too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving a frame with errors, currently we do nothing with it (we
don't construct an skb or an xdp_buff), we just exit the NAPI poll loop.
Let's put the buffer back into the RX ring (similar to XDP_DROP).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
enetc_put_xdp_buff has nothing to do with XDP, frankly, it is just a
helper to populate the recycle end of the shadow RX BD ring
(next_to_alloc) with a given buffer.
On the other hand, enetc_put_rx_buff plays more tricks than its name
would suggest.
So let's rename enetc_put_rx_buff into enetc_flip_rx_buff to reflect the
half-page buffer reuse tricks that it employs, and enetc_put_xdp_buff
into enetc_put_rx_buff which suggests a more garden-variety operation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Later in enetc_clean_tx_ring we have:
/* Scrub the swbd here so we don't have to do that
* when we reuse it during xmit
*/
memset(tx_swbd, 0, sizeof(*tx_swbd));
So these assignments are unnecessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-04-16
This series contains updates to igb and igc drivers.
Ederson adjusts Tx buffer distributions in Qav mode to improve
TSN-aware traffic for igb. He also enable PPS support and auxiliary PHC
functions for igc.
Grzegorz checks that the MTA register was properly written and
retries if not for igb.
Sasha adds reporting of EEE low power idle counters to ethtool and fixes
a return value being overwritten through looping for igc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following out-of-bounds warning:
net/core/flow_dissector.c:835:3: warning: 'memcpy' offset [33, 48] from the object at 'flow_keys' is out of the bounds of referenced subobject 'ipv6_src' with type '__u32[4]' {aka 'unsigned int[4]'} at offset 16 [-Warray-bounds]
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). So, the compiler legitimately complains about it. As these
are just a couple of members, fix this by copying each one of them in
separate calls to memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jakub Kicinski says:
====================
ethtool: add uAPI for reading standard stats
Continuing the effort of providing a unified access method
to standard stats, and explicitly tying the definitions to
the standards this series adds an API for general stats
which do no fit into more targeted control APIs.
There is nothing clever here, just a netlink API for dumping
statistics defined by standards and RFCs which today end up
in ethtool -S under infinite variations of names.
This series adds basic IEEE stats (for PHY, MAC, Ctrl frames)
and RMON stats. AFAICT other RFCs only duplicate the IEEE
stats.
This series does _not_ add a netlink API to read driver-defined
stats. There seems to be little to gain from moving that part
to netlink.
The netlink message format is very simple, and aims to allow
adding stats and groups with no changes to user tooling (which
IIUC is expected for ethtool).
On user space side we can re-use -S, and make it dump
standard stats if --groups are defined.
$ ethtool -S eth0 --groups eth-phy eth-mac eth-ctrl rmon
Stats for eth0:
eth-phy-SymbolErrorDuringCarrier: 0
eth-mac-FramesTransmittedOK: 0
eth-mac-FrameTooLongErrors: 0
eth-ctrl-MACControlFramesTransmitted: 0
eth-ctrl-MACControlFramesReceived: 1
eth-ctrl-UnsupportedOpcodesReceived: 0
rmon-etherStatsUndersizePkts: 0
rmon-etherStatsJabbers: 0
rmon-rx-etherStatsPkts64Octets: 1
rmon-rx-etherStatsPkts128to255Octets: 0
rmon-rx-etherStatsPkts1024toMaxOctets: 1
rmon-tx-etherStatsPkts64Octets: 1
rmon-tx-etherStatsPkts128to255Octets: 0
rmon-tx-etherStatsPkts1024toMaxOctets: 1
v1:
Driver support for mlxsw, mlx5 and bnxt included.
Compared to the RFC I went ahead with wrapping the stats into
a 1:1 nest. Now IDs of stats can start from 0, at a cost of
slightly "careful" u64 alignment handling.
v2:
Add missing kdoc in patch 5.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for PHY/MAC/Ctrl/RMON stats.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the names seem to strongly correlate with names from
the standard and RFC. Whether ..+good_frames are indeed Frames..OK
I'm the least sure of.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlxsw has nicely grouped stats, add support for standard uAPI.
I'm guessing the register access part. Compile tested only.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most devices maintain RMON (RFC 2819) stats - particularly
the "histogram" of packets received by size. Unlike other
RFCs which duplicate IEEE stats, the short/oversized frame
counters in RMON don't seem to match IEEE stats 1-to-1 either,
so expose those, too. Do not expose basic packet, CRC errors
etc - those are already otherwise covered.
Because standard defines packet ranges only up to 1518, and
everything above that should theoretically be "oversized"
- devices often create their own ranges.
Going beyond what the RFC defines - expose the "histogram"
in the Tx direction (assume for now that the ranges will
be the same).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Number of devices maintains the standard-based MAC control
counters for control frames. Add a API for those.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the MAC statistics are included in
struct rtnl_link_stats64, but some fields
are aggregated. Besides it's good to expose
these clearly hardware stats separately.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an interface for reading standard stats, including
stats which don't have a corresponding control interface.
Start with IEEE 802.3 PHY stats. There seems to be only
one stat to expose there.
Define API to not require user space changes when new
stats or groups are added. Groups are based on bitset,
stats have a string set associated.
v1: wrap stats in a nest
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add documentation for ETHTOOL_MSG_STATS_GET.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the lack of expectations for switching NICs explicit,
describe the new stats.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following out-of-bounds warning:
net/sctp/sm_make_chunk.c:3150:4: warning: 'memcpy' offset [17, 28] from the object at 'addr' is out of the bounds of referenced subobject 'v4' with type 'struct sockaddr_in' at offset 0 [-Warray-bounds]
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-04-16
This patchset introduces updates to mlx5e netdev driver.
1) Tariq refactors TLS offloads and adds resiliency against RX resync
failures
2) Maxim reduces code duplications by unifying channels reset flow
regardless if channels are closed or open
3) Aya Enhances TX/RX health reporters diagnostics to expose the
internal clock time-stamping format
4) Moshe adds support for ethtool extended link state, to show the reason
for link down
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Claudiu Manoil says:
====================
net: gianfar: Drop GFAR_MQ_POLLING support
Drop long time obsolete "per NAPI multi-queue" support in gianfar,
and related (and undocumented) device tree properties.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These are very old properties that were used by the "gianfar" ethernet
driver. They don't have documented bindings and are obsolete.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Gianfar used to enable all 8 Rx queues (DMA rings) per
ethernet device, even though the controller can only
support 2 interrupt lines at most. This meant that
multiple Rx queues would have to be grouped per NAPI poll
routine, and the CPU would have to split the budget and
service them in a round robin manner. The overhead of
this scheme proved to outweight the potential benefits.
The alternative was to introduce the "Single Queue" polling
mode, supporting one Rx queue per NAPI, which became the
default packet processing option and helped improve the
performance of the driver.
MQ_POLLING also relies on undocumeted device tree properties
to specify how to map the 8 Rx and Tx queues to a given
interrupt line (aka "interrupt group"). Using module parameters
to enable this mode wasn't an option either. Long story short,
MQ_POLLING became obsolete, now it is just dead code, and no
one asked for it so far.
For the Tx queues, multi-queue support (more than 1 Tx queue
per CPU) could be revisited by adding tc MQPRIO support, but
again, one has to consider that there are only 2 interrupt lines.
So the NAPI poll routine would have to service multiple Tx rings.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent patch that tied enabling of veth NAPI to the GRO flag also has
the nice side effect that a veth device can be the target of an
XDP_REDIRECT without an XDP program needing to be loaded on the peer
device. However, the patch adding this extra NAPI mode didn't actually
change the check in veth_xdp_xmit() to also look at the new NAPI pointer,
so let's fix that.
Fixes: 6788fa154546 ("veth: allow enabling NAPI even without XDP")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__ipv6_dev_mc_dec() internally uses sleepable functions so that caller
must not acquire atomic locks. But caller, which is addrconf_verify_rtnl()
acquires rcu_read_lock_bh().
So this warning occurs in the __ipv6_dev_mc_dec().
Test commands:
ip netns add A
ip link add veth0 type veth peer name veth1
ip link set veth1 netns A
ip link set veth0 up
ip netns exec A ip link set veth1 up
ip a a 2001:db8::1/64 dev veth0 valid_lft 2 preferred_lft 1
Splat looks like:
============================
WARNING: suspicious RCU usage
5.12.0-rc6+ #515 Not tainted
-----------------------------
kernel/sched/core.c:8294 Illegal context switch in RCU-bh read-side
critical section!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
4 locks held by kworker/4:0/1997:
#0: ffff88810bd72d48 ((wq_completion)ipv6_addrconf){+.+.}-{0:0}, at:
process_one_work+0x761/0x1440
#1: ffff888105c8fe00 ((addr_chk_work).work){+.+.}-{0:0}, at:
process_one_work+0x795/0x1440
#2: ffffffffb9279fb0 (rtnl_mutex){+.+.}-{3:3}, at:
addrconf_verify_work+0xa/0x20
#3: ffffffffb8e30860 (rcu_read_lock_bh){....}-{1:2}, at:
addrconf_verify_rtnl+0x23/0xc60
stack backtrace:
CPU: 4 PID: 1997 Comm: kworker/4:0 Not tainted 5.12.0-rc6+ #515
Workqueue: ipv6_addrconf addrconf_verify_work
Call Trace:
dump_stack+0xa4/0xe5
___might_sleep+0x27d/0x2b0
__mutex_lock+0xc8/0x13f0
? lock_downgrade+0x690/0x690
? __ipv6_dev_mc_dec+0x49/0x2a0
? mark_held_locks+0xb7/0x120
? mutex_lock_io_nested+0x1270/0x1270
? lockdep_hardirqs_on_prepare+0x12c/0x3e0
? _raw_spin_unlock_irqrestore+0x47/0x50
? trace_hardirqs_on+0x41/0x120
? __wake_up_common_lock+0xc9/0x100
? __wake_up_common+0x620/0x620
? memset+0x1f/0x40
? netlink_broadcast_filtered+0x2c4/0xa70
? __ipv6_dev_mc_dec+0x49/0x2a0
__ipv6_dev_mc_dec+0x49/0x2a0
? netlink_broadcast_filtered+0x2f6/0xa70
addrconf_leave_solict.part.64+0xad/0xf0
? addrconf_join_solict.part.63+0xf0/0xf0
? nlmsg_notify+0x63/0x1b0
__ipv6_ifa_notify+0x22c/0x9c0
? inet6_fill_ifaddr+0xbe0/0xbe0
? lockdep_hardirqs_on_prepare+0x12c/0x3e0
? __local_bh_enable_ip+0xa5/0xf0
? ipv6_del_addr+0x347/0x870
ipv6_del_addr+0x3b1/0x870
? addrconf_ifdown+0xfe0/0xfe0
? rcu_read_lock_any_held.part.27+0x20/0x20
addrconf_verify_rtnl+0x8a9/0xc60
addrconf_verify_work+0xf/0x20
process_one_work+0x84c/0x1440
In order to avoid this problem, it uses rcu_read_unlock_bh() for
a short time. RCU is used for avoiding freeing
ifp(struct *inet6_ifaddr) while ifp is being used. But this will
not be released even if rcu_read_unlock_bh() is used.
Because before rcu_read_unlock_bh(), it uses in6_ifa_hold(ifp).
So this is safe.
Fixes: 63ed8de4be81 ("mld: add mc_lock for protecting per-interface mld data")
Suggested-by: Eric Dumazet <edumazet@google.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alex Elder says:
====================
net: ipa: allow different firmware names
Add the ability to define a "firmware-name" property in the IPA DT
node, specifying an alternate name to use for the firmware file.
Used only if the AP (Trust Zone) does early IPA initialization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPA initialization includes loading some firmware. This step is
done either by the modem or by the AP under Trust Zone. If the
AP loads firmware, the name of the firmware file is currently
hard-coded ("ipa_fws.mdt").
Add the ability to specify the relative path of the firmware file to
use in a property in the Device Tree IPA node. If the property is
not found (or if any other error occurs attempting to get it), fall
back to using a default relative path.
Use the "old" fixed name as the default. Rename the symbol that
represents this default to emphasize its purpose.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new optional firmware-name property to the IPA DT node. It
is used only if the modem is not doing early initialization (i.e.,
if the modem-init property is not present). Its value is the name
of the firmware file to use; if it's not specified, a default name
("ipa_fws.mdt") is used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In page_to_skb(), if we have enough tailroom to save skb_shared_info, we
can use build_skb to create skb directly. No need to alloc for
additional space. And it can save a 'frags slot', which is very friendly
to GRO.
Here, if the payload of the received package is too small (less than
GOOD_COPY_LEN), we still choose to copy it directly to the space got by
napi_alloc_skb. So we can reuse these pages.
Testing Machine:
The four queues of the network card are bound to the cpu1.
Test command:
for ((i=0;i<5;++i)); do sockperf tp --ip 192.168.122.64 -m 1000 -t 150& done
The size of the udp package is 1000, so in the case of this patch, there
will always be enough tailroom to use build_skb. The sent udp packet
will be discarded because there is no port to receive it. The irqsoftd
of the machine is 100%, we observe the received quantity displayed by
sar -n DEV 1:
no build_skb: 956864.00 rxpck/s
build_skb: 1158465.00 rxpck/s
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MHI WWWAN control driver allows MHI QCOM-based modems to expose
different modem control protocols/ports via the WWAN framework, so that
userspace modem tools or daemon (e.g. ModemManager) can control WWAN
config and state (APN config, SMS, provider selection...). A QCOM-based
modem can expose one or several of the following protocols:
- AT: Well known AT commands interactive protocol (microcom, minicom...)
- MBIM: Mobile Broadband Interface Model (libmbim, mbimcli)
- QMI: QCOM MSM/Modem Interface (libqmi, qmicli)
- QCDM: QCOM Modem diagnostic interface (libqcdm)
- FIREHOSE: XML-based protocol for Modem firmware management
(qmi-firmware-update)
Note that this patch is mostly a rework of the earlier MHI UCI
tentative that was a generic interface for accessing MHI bus from
userspace. As suggested, this new version is WWAN specific and is
dedicated to only expose channels used for controlling a modem, and
for which related opensource userpace support exist.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change introduces initial support for a WWAN framework. Given the
complexity and heterogeneity of existing WWAN hardwares and interfaces,
there is no strict definition of what a WWAN device is and how it should
be represented. It's often a collection of multiple devices that perform
the global WWAN feature (netdev, tty, chardev, etc).
One usual way to expose modem controls and configuration is via high
level protocols such as the well known AT command protocol, MBIM or
QMI. The USB modems started to expose them as character devices, and
user daemons such as ModemManager learnt to use them.
This initial version adds the concept of WWAN port, which is a logical
pipe to a modem control protocol. The protocols are rawly exposed to
user via character device, allowing straigthforward support in existing
tools (ModemManager, ofono...). The WWAN core takes care of the generic
part, including character device management, and relies on port driver
operations to receive/submit protocol data.
Since the different devices exposing protocols for a same WWAN hardware
do not necessarily know about each others (e.g. two different USB
interfaces, PCI/MHI channel devices...) and can be created/removed in
different orders, the WWAN core ensures that all WAN ports contributing
to the 'whole' WWAN feature are grouped under the same virtual WWAN
device, relying on the provided parent device (e.g. mhi controller,
USB device). It's a 'trick' I copied from Johannes's earlier WWAN
subsystem proposal.
This initial version is purposely minimalist, it's essentially moving
the generic part of the previously proposed mhi_wwan_ctrl driver inside
a common WWAN framework, but the implementation is open and flexible
enough to allow extension for further drivers.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add parser entries for different IPv4 IHL values.
Each entry will set the L4 header offset according to the IPv4 IHL field.
L3 header offset will set during the parsing of the IPv4 protocol.
Because of missed parser support for IP header length > 20, RX IPv4 checksum HW offload fails
and skb->ip_summed set to CHECKSUM_NONE(checksum done by Network stack).
This patch adds RX IPv4 checksum HW offload capability for frames with IP header length > 20.
v1 --> v2
- Improve commit message.
Suggested-by: Dana Vardi <danat@marvell.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hayes Wang says:
====================
r8152: support new chips
Support new RTL8153 and RTL8156 series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The vendor mode is not always at config #1, so it is necessary to
set the correct configuration number.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support new firmware type and method for RTL8156 series.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support RTL8153C, RTL8153D, RTL8156A, and RTL8156B. The RTL8156A
and RTL8156B are the 2.5G ethernet.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The different chips may have different requests when changing mtu.
Therefore, add a new help function of rtl_ops to change mtu. Besides,
reset the tx/rx after changing mtu.
Additionally, add mtu_to_size() and size_to_mtu() macros to simplify
the code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use bits operations to record and check the firmware.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the maximum inter frame gap time (144ns) for speed 10M/half and
100M/half. It improves the performance for those speeds. And, there
is no effect for the other speeds.
For 10M/half and 100M/half, the fast inter frame gap time let the
device couldn't use the feature of the aggregation effectively,
because the transfer would be completed fastly. Therefore, use the
maximum value to improve the effect of the aggregation. However, you
may not feel the improvement for fast CPUs, because they compensate
for the effect of the aggregation.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The intention is for the loop to timeout if the body does not succeed.
The current logic calls time_is_before_jiffies(timeout) which is false
until after the timeout, so the loop body never executes.
Fix by using readl_poll_timeout as a more standard and less error-prone
solution.
Fixes: ba37b7caf1ed ("net: ethernet: mtk_eth_soc: add support for initializing the PPE")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mat Martineau says:
====================
mptcp: Improve socket option handling
MPTCP sockets have previously had limited socket option support. The
architecture of MPTCP sockets (one userspace-facing MPTCP socket that
manages one or more in-kernel TCP subflow sockets) adds complexity for
passing options through to lower levels. This patch set adds MPTCP
support for socket options commonly used with TCP.
Patch 1 reverts an interim socket option fix (a socket option blocklist)
that was merged in the net tree for v5.12.
Patch 2 moves the socket option code to a separate file, with no
functional changes.
Patch 3 adds an allowlist for socket options that are known to function
with MPTCP. Later patches in this set add more allowed options.
Patches 4 and 5 add infrastructure for syncing MPTCP-level options with
the TCP subflows.
Patches 6-12 add support for specific socket options.
Patch 13 adds a socket option self test.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend mptcp_connect tool with SO_MARK support (-M <value>) and
add a test case that checks that the packet mark gets copied to all
subflows.
This is done by only allowing packets with either skb->mark 1 or 2
via iptables.
DROP rule packet counter is checked; if its not zero, print an error
message and fail the test case.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCP_CONGESTION is set for all subflows.
The mptcp socket gains icsk_ca_ops too so it can be used to keep the
authoritative state that should be set on new/future subflows.
TCP_INFO will return first subflow only.
The out-of-tree kernel has a MPTCP_INFO getsockopt, this could be added
later on.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handle SO_DEBUG and set it on all subflows.
Ignore those values not implemented on TCP sockets.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
