summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2012-10-07mmc: sdhci-spear: add device tree bindingsViresh Kumar4-6/+77
This adds simple DT bindings for SDHCI SPEAr controller. It uses cd-gpios from common mmc bindings. This also fixes spear300-evb.dts with correct name for card detect binding. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-07mmc: sdhci-s3c: Add clk_(enable/disable) in runtime suspend/resumeChander Kashyap1-2/+27
Perform clock disable/enable in runtime suspend/resume. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-07mmc: core: Replace MMC_CAP2_BROKEN_VOLTAGE with test for fixed regulatorChris Ball1-4/+6
Before this patch, we were using MMC_CAP2_BROKEN_VOLTAGE as a way to avoid calling regulator_set_voltage() on a fixed regulator, but that's just duplicating information that already exists -- we should test whether the regulator is fixed directly, instead of via a capability. This patch implements that test. We can't reclaim the capability bit just yet, since there are still boards in arch/arm/ that reference it; those references can be removed now. Reported-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-07mmc: sdhci-pxav3: Use sdhci_get_of_property for parsing DT quirksChris Ball1-0/+2
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-07mmc: dt: Support "broken-cd" property in sdhci-pltfmChris Ball1-0/+3
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-07mmc: sdhci-s3c: fix the wrong number of max bus clocksJaehoon Chung1-1/+1
We can use up to four bus-clocks; but on module remove, we didn't disable the fourth bus clock. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: sh-mmcif: avoid oops on spurious interruptsGuennadi Liakhovetski1-0/+4
On some systems, e.g., kzm9g, MMCIF interfaces can produce spurious interrupts without any active request. To prevent the Oops, that results in such cases, don't dereference the mmc request pointer until we make sure, that we are indeed processing such a request. Reported-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp> Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Cc: stable <stable@vger.kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: sh-mmcif: properly handle MMC_WRITE_MULTIPLE_BLOCK completion IRQGuennadi Liakhovetski1-1/+3
Upon completion of a MMC_WRITE_MULTIPLE_BLOCK command MMCIF issues an IRQ with the DTRANE bit set and often with one or several of CMD12 bits set. If those interrupts are not acknowledged, an additional interrupt can be produced and will be delivered later, possibly, when the transaction has already been completed. To prevent this from happening, CMD12 completion interrupt sources have to be cleared too upon reception of an DTRANE IRQ. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Tested-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: sdhci-s3c: Fix crash on module insertion for second timeChander Kashyap1-0/+1
If sdhci-s3c driver is built as module, it gives following error if inserted again after removing. This was happening as pm_runtime_use_autosuspend() is called in sdhci_s3c_probe() function but in sdhci_s3c_remove() its complementary pm_runtime_dont_use_autosuspend() is not called. BUG: spinlock bad magic on CPU#1, insmod/955 lock: 0xee771368, .magic: 00000000, .owner: insmod/955, .owner_cpu: 1 [<c00147e0>] (unwind_backtrace+0x0/0xf8) from [<c0136b40>] (do_raw_spin_unlock+0xa4/0xe4) [<c0136b40>] (do_raw_spin_unlock+0xa4/0xe4) from [<c01be508>] (_raw_spin_unlock_irqrestore+0xc/0x38) [<c01be508>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c01a9334>] (sdhci_runtime_suspend_host+0x54/0x80) [<c01a9334>] (sdhci_runtime_suspend_host+0x54/0x80) from [<bf0060a8>] (sdhci_s3c_runtime_suspend+0x14/0x38 [sdhci_s3c]) [<bf0060a8>] (sdhci_s3c_runtime_suspend+0x14/0x38 [sdhci_s3c]) from [<c016cb00>] (pm_generic_runtime_suspend+0x2c/0x40) [<c016cb00>] (pm_generic_runtime_suspend+0x2c/0x40) from [<c0170090>] (__rpm_callback+0x70/0x98) [<c0170090>] (__rpm_callback+0x70/0x98) from [<c01703f0>] (rpm_suspend+0xf0/0x534) [<c01703f0>] (rpm_suspend+0xf0/0x534) from [<c0171670>] (__pm_runtime_suspend+0x5c/0x74) [<c0171670>] (__pm_runtime_suspend+0x5c/0x74) from [<c016d018>] (pm_generic_runtime_idle+0x44/0x4c) [<c016d018>] (pm_generic_runtime_idle+0x44/0x4c) from [<c0170090>] (__rpm_callback+0x70/0x98) [<c0170090>] (__rpm_callback+0x70/0x98) from [<c0170984>] (rpm_idle+0xdc/0x18c) [<c0170984>] (rpm_idle+0xdc/0x18c) from [<c0171608>] (pm_runtime_set_autosuspend_delay+0x30/0x3c) [<c0171608>] (pm_runtime_set_autosuspend_delay+0x30/0x3c) from [<bf0069c4>] (sdhci_s3c_probe+0x35c/0x52c [sdhci_s3c]) [<bf0069c4>] (sdhci_s3c_probe+0x35c/0x52c [sdhci_s3c]) from [<c016a014>] (platform_drv_probe+0x18/0x1c) Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: sdhci-s3c: Enable only required bus clockChander Kashyap1-5/+7
In case of multiple bus clock sources, all the clock sources were getting enabled. As only one clock source is needed at the time hence enable only the required bus clock. This patch does as follows: 1. In sdhci_s3c_probe enable only required bus clock source. 2. Handle the disabling of old bus clock and enables the best clock selected in sdhci_s3c_set_clock(). Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: Revert "mmc: dw_mmc: Add check for IDMAC configuration"Seungwon Jeon1-13/+2
This reverts commit 94c6cee91 (Add check for IDMAC configuration). Synopsys says that only if internal dmac is not present, optional external dma interface is present. When internal dmac is present, '0' value in DMA_INTERFACE of HCON is reasonable. DMA_INTERFACE indicates external dma interface. And idmac initialization is prohibited now. The commit should be reverted since: the check for IDMAC is not reliable; falling back to PIO would provide awful performance; we wouldn't expect to see instances of this block without DMA support. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: mxcmmc: fix bug that may block a data transfer foreverJavier Martin1-6/+70
The problem can be easily reproduced using a script that loops copying a file in an SD card to another place in the same SD card and its related to read transfers. This only happens with DMA enabled. This is related to the fact that, when reading, an MMC irq signals the fact that all data from the SD card has been copied to the internal buffers. However, it doesn't signal whether the DMA transfer that is in charge of moving data from these internal buffers to RAM has finished or not. Thus, calling dmaengine_terminate_all() in the MMC irq routine can cancel an ongoing DMA transfer leaving some data in the internal buffers that produces an accumulative effect which, in the end, blocks a read data transfer forever. The following patch watches DMA irq for reading and MMC irqs for writing transfers. The 'dangerous' usage of dmaengine_terminate_all() is removed and a timeout of 10 seconds is added so that the MMC won't block forever anymore. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: omap_hsmmc: Pass on the suspend failure to the PM coreVaibhav Bedia1-2/+1
In some cases mmc_suspend_host() is not able to claim the host and proceed with the suspend process. The core returns -EBUSY to the host controller driver. Unfortunately, the host controller driver does not pass on this information to the PM core and hence the system suspend process continues. ret = mmc_suspend_host(host->mmc); if (ret) { host->suspended = 0; if (host->pdata->resume) { ret = host->pdata->resume(dev, host->slot_id); The return status from mmc_suspend_host() is overwritten by return status from host->pdata->resume. So the original return status is lost. In these cases the MMC core gets to an unexpected state during resume and multiple issues related to MMC crop up. 1. Host controller driver starts accessing the device registers before the clocks are enabled which leads to a prefetch abort. 2. A file copy thread which was launched before suspend gets stuck due to the host not being reclaimed during resume. To avoid such problems pass on the -EBUSY status to the PM core from the host controller driver. With this change, MMC core suspend might still fail but it does not end up making the system unusable. Suspend gets aborted and the user can try suspending the system again. Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com> Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com> Acked-by: Venkatraman S <svenkatr@ti.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: atmel-mci: AP700x PDC is not connected to MCIHein_Tibosch2-1/+8
Earlier, atmel-mci was adapted to make use of the peripheral DMA controller (PDC), in case normal DMA wouldn't work. ( http://comments.gmane.org/gmane.linux.kernel.mmc/9403 ) This works OK on ARM platforms (AT91), but it broke the driver for AVR32, the AP700x. Although the MCI has PDC support, the connection is not done for AVR chips. This patch makes the use of PDC depend on !CONFIG_AVR32. Signed-off-by: Hein Tibosch <hein_tibosch@yahoo.es> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: atmel-mci: DMA can be used with other controllersHein_Tibosch1-13/+13
After the latest changes to atmel-mci, it could not be used with DMA on the AVR32 platform. This patch will allow to use DMA again and it will avoid access to MCI register ATMCI_DMA. Even if the IP version is lower than v3xx and doesn't have the DMA configuration register, DMA transfers can be used with a different controller than the Atmel AHB DMA one. For instance, some AVR chips use the Synopsys DesignWare AHB DMA controller. Signed-off-by: Hein Tibosch <hein_tibosch@yahoo.es> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: mmci: use clk_prepare_enable and clk_disable_unprepareJulia Lawall1-10/+3
clk_prepare_enable and clk_disable_unprepare combine clk_prepare and clk_enable, and clk_disable and clk_unprepare. They make the code more concise, and ensure that clk_unprepare is called when clk_enable fails. A simplified version of the semantic patch that introduces calls to these functions is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression e; @@ - clk_prepare(e); - clk_enable(e); + clk_prepare_enable(e); @@ expression e; @@ - clk_disable(e); - clk_unprepare(e); + clk_disable_unprepare(e); // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: sdhci-s3c: Add device tree supportThomas Abraham2-6/+205
Add device tree based discovery support for Samsung's sdhci controller. Cc: Ben Dooks <ben-linux@fluff.org> Cc: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: dw_mmc: add support for exynos specific implementation of dw-mshcThomas Abraham5-1/+351
Samsung Exynos SoC's extend the dw-mshc controller for additional clock and bus control. Add support for these extensions and include provide device tree based discovery suppory as well. Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: dw_mmc: add support for implementation specific callbacksThomas Abraham5-4/+86
The core dw-mshc controller driver can let platform specific implementations of the dw-mshc controller to control the hardware as required by such implementations. This is acheived by invoking implementation specific (optional) callbacks. Define the list of callbacks supported the add invocation points for the same. Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: dw_mmc: prepare functions in dw_mmc-pltfm for reuseThomas Abraham2-2/+29
Platform implementations of dw-mshc controller may choose to extend the features of the standard dw-mshc controller such as adding additional clocking options or modifying the bus interface. Support for such implementation specific extensions can be incorporated into dw_mmc-pltfm, but including multiple such platform specific implementations would convolute the existing dw_mmc-pltfm code. Instead, it would be better to create implementation specific platform drivers to support implementation specific features. Such platforms drivers can reuse the existing infrastructure in dw_mmc-pltfm for resource identification and controller registration and provide support for implementation specific features. So, allow the infrastructure in dw_mmc-pltfm to be reused by other implementation specific platform drivers. Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: dw_mmc: add device tree supportThomas Abraham3-7/+211
Add device tree based discovery support. Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: dw_mmc: add quirk to indicate missing write protect lineThomas Abraham2-2/+5
If the write protect pad of the controller is not connected to the write protect pin of the slot, the driver should be notified of this condition so that incorrect check for write protection by reading the WRTORT register can avoided. The get_ro platform callback can be used for in such cases, but with device tree support enabled, such platform callbacks cannot be supported. Add a new quirk for notifying the driver about the missing write protect line so the driver can assume that the card write protection is disabled. Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: dw_mmc: lookup for optional biu and ciu clocksThomas Abraham2-3/+53
Some platforms allow for clock gating and control of bus interface unit clock and card interface unit clock. Add support for clock lookup of optional biu and ciu clocks for clock gating and clock speed determination. Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: dw_mmc: allow probe to succeed even if one slot is initializedThomas Abraham1-10/+13
Instead of aborting the probe when a slot initialization fails, allow initialization of as many slots as possible. If there is at least one instance of a slot that is successfully initialized, allow the driver probe to succeed. Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: dw_mmc: Use devm_* functions in dw_mmc platform driverThomas Abraham1-21/+8
Use devm_* managed functions for simpler error handling. Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: dw_mmc: convert copy of struct device in struct dw_mci to a referenceThomas Abraham4-31/+31
The 'struct dw_mci' maintains a copy of the pdev->dev instance instead of maintaining a reference to that 'struct device' instance. Any resource allocated using the device resource management kernel API with the instance of 'struct device' in 'struct dw_mci' is then incorrect. Fix this by converting the copy of 'struct device' in 'struct dw_mci' to a reference. Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03mmc: support BKOPS feature for eMMCJaehoon Chung6-8/+220
Enable eMMC background operations (BKOPS) feature. If URGENT_BKOPS is set after a response, note that BKOPS are required. Immediately run BKOPS if required. Read/write operations should be requested during BKOPS(LEVEL-1), then issue HPI to interrupt the ongoing BKOPS and service the foreground operation. (This patch only controls the LEVEL2/3.) When repeating the writing 1GB data, at a certain time, performance is decreased. At that time, card triggers the Level-3 or Level-2. After running bkops, performance is recovered. Future considerations: * Check BKOPS_LEVEL=1 and start BKOPS in a preventive manner. * Interrupt ongoing BKOPS before powering off the card. * How do we get BKOPS_STATUS value (periodically send ext_csd command)? * If using periodic bkops, also consider runtime_pm control. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org> Reviewed-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-19mmc: sdhci: Test cd-gpio instead of SDHCI presence when probingGuennadi Liakhovetski1-0/+8
Previously to this patch, an SDHCI platform that uses a GPIO for card detection instead of the internal SDHCI_CARD_PRESENT bit on the presence register would fail to detect a new card. Some drivers worked around this in various ways: esdhc-imx defines an IO accessor to fake the presence bit being true, s3c turns on polling (which stops the SDHCI driver from checking the bit) after a card's inserted. But none of this should be necessary; the real fix is to check whether we're using a GPIO and avoid relying on the presence bit if so, as this patch implements. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-19mmc: davinci_mmc: convert to DMA engine APIMatt Porter1-189/+82
Removes use of the DaVinci EDMA private DMA API and replaces it with use of the DMA engine API. Signed-off-by: Matt Porter <mporter@ti.com> Tested-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-19mmc: sdio: Fix PM_SLEEP related build warningsThierry Reding1-7/+0
Power management callbacks defined by SIMPLE_DEV_PM_OPS are only used if the PM_SLEEP Kconfig symbol has been defined. If not, the compiler will complain about them being unused. However, since the callback for this driver doesn't do anything it can just as well be dropped. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-19mmc: core: Remove bounce buffer in mmc_send_cxd_data()Kyungsik Lee1-16/+42
It is expected that Extended CSD register (the size of this register is larger than CID/CSD) will be referenced more frequently as more fields have been added to Extended CSD and it seems that it is not a good option to double the memory used. This patch is intended to avoid the use of bounce buffer for reading Extended CSD register in mmc_send_cxd_data(). It will provide a better performance gain by removing memcpy() overhead for a half KiB and a redundant bounce buffer allocated repeatedly at the cost of providing DMA-capable buffer from upper caller (but on-stack buffer is allowed with no performance gain). Signed-off-by: Kyungsik Lee <kyungsik.lee@lge.com> Reviewed-by: Venkatraman S <svenkatr@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-19mmc: sdhci-pxav3: dt: Support "cd-gpios" propertyChris Ball2-0/+26
Tested on OLPC XO-4/MMP3, where the card detection pin for one of the controllers is a sideband GPIO. The third cell in the cd-gpios property controls whether the GPIO is active high/active low. (Also, pass host_caps2 through from platdata to the mmc host.) Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> [kliu5@marvell.com: Compile fix] Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-11mmc: slot-gpio: Fix missing assignment to ctx->ro_gpioChris Ball1-1/+7
mmc_gpio_request_ro() doesn't store the requested gpio in ctx->ro_gpio. As a result, subsequent calls to mmc_gpio_get_ro() will always fail with -ENOSYS because the gpio number isn't available to that function. Cc: stable <stable@vger.kernel.org> Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: via-sdmmc: Use module_pci_driverSachin Kamat1-15/+1
module_pci_driver makes the code simpler by eliminating module_init and module_exit calls. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Acked-by: Harald Welte <laforge@gnumonks.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: dw_mmc-pci: Use module_pci_driverSachin Kamat1-12/+1
module_pci_driver makes the code simpler by eliminating module_init and module_exit calls. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: sdhci-pci: Use module_pci_driverSachin Kamat1-18/+1
module_pci_driver makes the code simpler by eliminating module_init and module_exit calls. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: mmc_spi: Use module_spi_driverSachin Kamat1-14/+1
module_spi_driver makes the code simpler by eliminating module_init and module_exit calls. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: sdhci-s3c: fix checkpatch error and warningsJingoo Han1-6/+8
This patch fixes the checkpatch error and warnings listed below: ERROR: return is not a function, parentheses are not required WARNING: Prefer pr_err(... to printk(KERN_ERR, ... WARNING: quoted string split across lines WARNING: line over 80 characters WARNING: braces {} are not necessary for single statement blocks Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: core: Do not rescan non-removable devicesJohan Rudholm2-0/+6
If MMC_CAP_NONREMOVABLE is set, only issue a detect job on init. Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: dw_mmc: fixed a section mismatch in dw_mci_init_slotJaehoon Chung2-3/+3
Fixed the below message. WARNING: drivers/mmc/host/built-in.o(.text+0x5ee8): Section mismatch in reference from the function dw_mci_probe() to the function .init.text:dw_mci_init_slot() The function dw_mci_probe() references the function __init dw_mci_init_slot(). This is often because dw_mci_probe lacks a __init annotation or the annotation of dw_mci_init_slot is wrong Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: tegra: convert to device tree support onlyJoseph Lo1-4/+3
When compiling a kernel that supports only Tegra30 and not Tegra20, the SDHCI driver will fail to compile since the of_match_device() failure fallback code unconditinally references soc_data_tegra20, which is only compiled in when Tegra20 support is enabled. In Kernel 3.7, both Tegra20 and Tegra30 will only support booting using device tree, Hence, there is never a need to fall back to using soc_data_tegra20 if of_mach_device() fails. Instead, make this case an error. This removes the reference to soc_data_tegra20, and hence solves the compile failure. Signed-off-by: Joseph Lo <josephl@nvidia.com> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: dt: Add card-detection properties to core binding.Chris Ball1-2/+7
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: omap_hsmmc: Move to Maintained state in MAINTAINERSVenkatraman S1-1/+3
I can continue to look after this driver. Signed-off-by: Venkatraman S <svenkatr@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: omap_hsmmc: consolidate error report handling of HSMMC IRQVenkatraman S1-42/+21
Consolidate the duplicated code around the handling of CMD_TIMEOUT, CMD_CRC, DATA_TIMEOUT, DATA_CRC and CARD_ERR handling into a single function. This generally shrinks code bloat, but is also required for implementing software based guard timers. Signed-off-by: Venkatraman S <svenkatr@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: omap_hsmmc: consolidate flush posted writes for HSMMC IRQsVenkatraman S1-13/+4
Flushing spurious IRQs from HSMMC IP is done twice in omap_hsmmc_irq and omap_hsmmc_do_irq. Consolidate them to one location. Signed-off-by: Venkatraman S <svenkatr@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: omap_hsmmc: remove access to SYSCONFIG registerVenkatraman S1-22/+2
SYSCONFIG register of HSMMC IP is managed by the omap hwmod abstraction layer. Resetting the IP and configuring the correct SYSCONFIG mode is centrally managed by hwmod. Remove code which manipulates IP reset and SYSCONFIG directly in the driver. Signed-off-by: Venkatraman S <svenkatr@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: omap_hsmmc: remove unused vars and includesVenkatraman S1-10/+4
Some straight forward cleanup of unnecessary #include's and host variables. Some of the verbose and redundant debug messages are converted to use dev_vdbg. Signed-off-by: Venkatraman S <svenkatr@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: omap: fix mmc_omap_report_irq to use dev_dbg macrosVenkatraman S1-12/+17
The function mmc_omap_report_irq uses raw printks and the actual output was disabled by a static variable. Make the function use dev_vdbg macro and use it under the standard CONFIG_MMC_DEBUG flag. Signed-off-by: Venkatraman S <svenkatr@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: omap: remove unused variables and includesVenkatraman S1-10/+0
Get rid of some unnecessary includes in the driver and a few unused variables. Signed-off-by: Venkatraman S <svenkatr@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04mmc: debugfs: Print ext_csd in ascending orderVenkatraman S1-1/+1
ext_csd exported through debugfs is printed in reverse order (from byte 511 to 0), which causes confusion. Fix the for loop to print ext_csd in natural order. Signed-off-by: Venkatraman S <svenkatr@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-08-23 17:37:45 +0000