summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2020-02-20net: netlink: cap max groups which will be considered in netlink_bind()Nikolay Aleksandrov1-2/+3
Since nl_groups is a u32 we can't bind more groups via ->bind (netlink_bind) call, but netlink has supported more groups via setsockopt() for a long time and thus nlk->ngroups could be over 32. Recently I added support for per-vlan notifications and increased the groups to 33 for NETLINK_ROUTE which exposed an old bug in the netlink_bind() code causing out-of-bounds access on archs where unsigned long is 32 bits via test_bit() on a local variable. Fix this by capping the maximum groups in netlink_bind() to BITS_PER_TYPE(u32), effectively capping them at 32 which is the minimum of allocated groups and the maximum groups which can be bound via netlink_bind(). CC: Christophe Leroy <christophe.leroy@c-s.fr> CC: Richard Guy Briggs <rgb@redhat.com> Fixes: 4f520900522f ("netlink: have netlink per-protocol bind function return an error code.") Reported-by: Erhard F. <erhard_f@mailbox.org> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20net: thunderx: workaround BGX TX Underflow issueTim Harvey2-3/+68
While it is not yet understood why a TX underflow can easily occur for SGMII interfaces resulting in a TX wedge. It has been found that disabling/re-enabling the LMAC resolves the issue. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Robert Jones <rjones@gateworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20ionic: fix fw_status readShannon Nelson2-4/+8
The fw_status field is only 8 bits, so fix the read. Also, we only want to look at the one status bit, to allow for future use of the other bits, and watch for a bad PCI read. Fixes: 97ca486592c0 ("ionic: add heartbeat check") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20net: disable BRIDGE_NETFILTER by defaultRoman Kiryanov1-1/+0
The description says 'If unsure, say N.' but the module is built as M by default (once the dependencies are satisfied). When the module is selected (Y or M), it enables NETFILTER_FAMILY_BRIDGE and SKB_EXTENSIONS which alter kernel internal structures. We (Android Studio Emulator) currently do not use this module and think this it is more consistent to have it disabled by default as opposite to disabling it explicitly to prevent enabling NETFILTER_FAMILY_BRIDGE and SKB_EXTENSIONS. Signed-off-by: Roman Kiryanov <rkir@google.com> Acked-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20net: macb: Properly handle phylink on at91rm9200Alexandre Belloni2-28/+33
at91ether_init was handling the phy mode and speed but since the switch to phylink, the NCFGR register got overwritten by macb_mac_config(). The issue is that the RM9200_RMII bit and the MACB_CLK_DIV32 field are cleared but never restored as they conflict with the PAE, GBE and PCSSEL bits. Add new capability to differentiate between EMAC and the other versions of the IP and use it to set and avoid clearing the relevant bits. Also, this fixes a NULL pointer dereference in macb_mac_link_up as the EMAC doesn't use any rings/bufffers/queues. Fixes: 7897b071ac3b ("net: macb: convert to phylink") Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20Merge branch 's390-fixes'David S. Miller2-18/+14
Julian Wiedmann says: ==================== s390/qeth: fixes 2020-02-20 please apply the following patch series for qeth to netdev's net tree. This corrects three minor issues: 1) return a more fitting errno when VNICC cmds are not supported, 2) remove a bogus WARN in the NAPI code, and 3) be _very_ pedantic about the RX copybreak. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20s390/qeth: fix off-by-one in RX copybreak checkJulian Wiedmann1-1/+1
The RX copybreak is intended as the _max_ value where the frame's data should be copied. So for frame_len == copybreak, don't build an SG skb. Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20s390/qeth: don't warn for napi with 0 budgetJulian Wiedmann1-1/+0
Calling napi->poll() with 0 budget is a legitimate use by netpoll. Fixes: a1c3ed4c9ca0 ("qeth: NAPI support for l2 and l3 discipline") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20s390/qeth: vnicc Fix EOPNOTSUPP precedenceAlexandra Winter1-16/+13
When getting or setting VNICC parameters, the error code EOPNOTSUPP should have precedence over EBUSY. EBUSY is used because vnicc feature and bridgeport feature are mutually exclusive, which is a temporary condition. Whereas EOPNOTSUPP indicates that the HW does not support all or parts of the vnicc feature. This issue causes the vnicc sysfs params to show 'blocked by bridgeport' for HW that does not support VNICC at all. Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20openvswitch: Distribute switch variables for initializationKees Cook1-8/+10
Variables declared in a switch statement before any case statements cannot be automatically initialized with compiler instrumentation (as they are not part of any execution flow). With GCC's proposed automatic stack variable initialization feature, this triggers a warning (and they don't get initialized). Clang's automatic stack variable initialization (via CONFIG_INIT_STACK_ALL=y) doesn't throw a warning, but it also doesn't initialize such variables[1]. Note that these warnings (or silent skipping) happen before the dead-store elimination optimization phase, so even when the automatic initializations are later elided in favor of direct initializations, the warnings remain. To avoid these problems, move such variables into the "case" where they're used or lift them up into the main function body. net/openvswitch/flow_netlink.c: In function ‘validate_set’: net/openvswitch/flow_netlink.c:2711:29: warning: statement will never be executed [-Wswitch-unreachable] 2711 | const struct ovs_key_ipv4 *ipv4_key; | ^~~~~~~~ [1] https://bugs.llvm.org/show_bug.cgi?id=44916 Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20net: ip6_gre: Distribute switch variables for initializationKees Cook2-7/+14
Variables declared in a switch statement before any case statements cannot be automatically initialized with compiler instrumentation (as they are not part of any execution flow). With GCC's proposed automatic stack variable initialization feature, this triggers a warning (and they don't get initialized). Clang's automatic stack variable initialization (via CONFIG_INIT_STACK_ALL=y) doesn't throw a warning, but it also doesn't initialize such variables[1]. Note that these warnings (or silent skipping) happen before the dead-store elimination optimization phase, so even when the automatic initializations are later elided in favor of direct initializations, the warnings remain. To avoid these problems, move such variables into the "case" where they're used or lift them up into the main function body. net/ipv6/ip6_gre.c: In function ‘ip6gre_err’: net/ipv6/ip6_gre.c:440:32: warning: statement will never be executed [-Wswitch-unreachable] 440 | struct ipv6_tlv_tnl_enc_lim *tel; | ^~~ net/ipv6/ip6_tunnel.c: In function ‘ip6_tnl_err’: net/ipv6/ip6_tunnel.c:520:32: warning: statement will never be executed [-Wswitch-unreachable] 520 | struct ipv6_tlv_tnl_enc_lim *tel; | ^~~ [1] https://bugs.llvm.org/show_bug.cgi?id=44916 Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20net: core: Distribute switch variables for initializationKees Cook1-2/+2
Variables declared in a switch statement before any case statements cannot be automatically initialized with compiler instrumentation (as they are not part of any execution flow). With GCC's proposed automatic stack variable initialization feature, this triggers a warning (and they don't get initialized). Clang's automatic stack variable initialization (via CONFIG_INIT_STACK_ALL=y) doesn't throw a warning, but it also doesn't initialize such variables[1]. Note that these warnings (or silent skipping) happen before the dead-store elimination optimization phase, so even when the automatic initializations are later elided in favor of direct initializations, the warnings remain. To avoid these problems, move such variables into the "case" where they're used or lift them up into the main function body. net/core/skbuff.c: In function ‘skb_checksum_setup_ip’: net/core/skbuff.c:4809:7: warning: statement will never be executed [-Wswitch-unreachable] 4809 | int err; | ^~~ [1] https://bugs.llvm.org/show_bug.cgi?id=44916 Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-19Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller10-31/+93
Alexei Starovoitov says: ==================== pull-request: bpf 2020-02-19 The following pull-request contains BPF updates for your *net* tree. We've added 10 non-merge commits during the last 10 day(s) which contain a total of 10 files changed, 93 insertions(+), 31 deletions(-). The main changes are: 1) batched bpf hashtab fixes from Brian and Yonghong. 2) various selftests and libbpf fixes. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-19Merge branch '100GbE' of ↵David S. Miller4-80/+115
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2020-02-19 This series contains fixes to the ice driver. Brett fixes an issue where if a user sets an odd [tx|rx]-usecs value through ethtool, the request is denied because the hardware is set to have an ITR with 2us granularity. Also fix an issue where the VF has not been completely removed/reset after being unbound from the host driver, so resolve this by waiting for the VF remove/reset process to happen before checking if the VF is disabled. Michal fixes an issue, where when the user changes flow control via ethtool, the OS is told the link is going down when that may not be the case. Before the fix, the only way to get out of this state was to take the interface down and up again. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-19udp: rehash on disconnectWillem de Bruijn1-1/+5
As of the below commit, udp sockets bound to a specific address can coexist with one bound to the any addr for the same port. The commit also phased out the use of socket hashing based only on port (hslot), in favor of always hashing on {addr, port} (hslot2). The change broke the following behavior with disconnect (AF_UNSPEC): server binds to 0.0.0.0:1337 server connects to 127.0.0.1:80 server disconnects client connects to 127.0.0.1:1337 client sends "hello" server reads "hello" // times out, packet did not find sk On connect the server acquires a specific source addr suitable for routing to its destination. On disconnect it reverts to the any addr. The connect call triggers a rehash to a different hslot2. On disconnect, add the same to return to the original hslot2. Skip this step if the socket is going to be unhashed completely. Fixes: 4cdeeee9252a ("net: udp: prefer listeners bound to an address") Reported-by: Pavel Roskin <plroskin@gmail.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-19net/tls: Fix to avoid gettig invalid tls recordRohit Maheshwari1-1/+19
Current code doesn't check if tcp sequence number is starting from (/after) 1st record's start sequnce number. It only checks if seq number is before 1st record's end sequnce number. This problem will always be a possibility in re-transmit case. If a record which belongs to a requested seq number is already deleted, tls_get_record will start looking into list and as per the check it will look if seq number is before the end seq of 1st record, which will always be true and will return 1st record always, it should in fact return NULL. As part of the fix, start looking each record only if the sequence number lies in the list else return NULL. There is one more check added, driver look for the start marker record to handle tcp packets which are before the tls offload start sequence number, hence return 1st record if the record is tls start marker and seq number is before the 1st record's starting sequence number. Fixes: e8f69799810c ("net/tls: Add generic NIC offload infrastructure") Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-19bpf: Fix a potential deadlock with bpf_map_do_batchYonghong Song1-3/+31
Commit 057996380a42 ("bpf: Add batch ops to all htab bpf map") added lookup_and_delete batch operation for hash table. The current implementation has bpf_lru_push_free() inside the bucket lock, which may cause a deadlock. syzbot reports: -> #2 (&htab->buckets[i].lock#2){....}: __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline] _raw_spin_lock_irqsave+0x95/0xcd kernel/locking/spinlock.c:159 htab_lru_map_delete_node+0xce/0x2f0 kernel/bpf/hashtab.c:593 __bpf_lru_list_shrink_inactive kernel/bpf/bpf_lru_list.c:220 [inline] __bpf_lru_list_shrink+0xf9/0x470 kernel/bpf/bpf_lru_list.c:266 bpf_lru_list_pop_free_to_local kernel/bpf/bpf_lru_list.c:340 [inline] bpf_common_lru_pop_free kernel/bpf/bpf_lru_list.c:447 [inline] bpf_lru_pop_free+0x87c/0x1670 kernel/bpf/bpf_lru_list.c:499 prealloc_lru_pop+0x2c/0xa0 kernel/bpf/hashtab.c:132 __htab_lru_percpu_map_update_elem+0x67e/0xa90 kernel/bpf/hashtab.c:1069 bpf_percpu_hash_update+0x16e/0x210 kernel/bpf/hashtab.c:1585 bpf_map_update_value.isra.0+0x2d7/0x8e0 kernel/bpf/syscall.c:181 generic_map_update_batch+0x41f/0x610 kernel/bpf/syscall.c:1319 bpf_map_do_batch+0x3f5/0x510 kernel/bpf/syscall.c:3348 __do_sys_bpf+0x9b7/0x41e0 kernel/bpf/syscall.c:3460 __se_sys_bpf kernel/bpf/syscall.c:3355 [inline] __x64_sys_bpf+0x73/0xb0 kernel/bpf/syscall.c:3355 do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294 entry_SYSCALL_64_after_hwframe+0x49/0xbe -> #0 (&loc_l->lock){....}: check_prev_add kernel/locking/lockdep.c:2475 [inline] check_prevs_add kernel/locking/lockdep.c:2580 [inline] validate_chain kernel/locking/lockdep.c:2970 [inline] __lock_acquire+0x2596/0x4a00 kernel/locking/lockdep.c:3954 lock_acquire+0x190/0x410 kernel/locking/lockdep.c:4484 __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline] _raw_spin_lock_irqsave+0x95/0xcd kernel/locking/spinlock.c:159 bpf_common_lru_push_free kernel/bpf/bpf_lru_list.c:516 [inline] bpf_lru_push_free+0x250/0x5b0 kernel/bpf/bpf_lru_list.c:555 __htab_map_lookup_and_delete_batch+0x8d4/0x1540 kernel/bpf/hashtab.c:1374 htab_lru_map_lookup_and_delete_batch+0x34/0x40 kernel/bpf/hashtab.c:1491 bpf_map_do_batch+0x3f5/0x510 kernel/bpf/syscall.c:3348 __do_sys_bpf+0x1f7d/0x41e0 kernel/bpf/syscall.c:3456 __se_sys_bpf kernel/bpf/syscall.c:3355 [inline] __x64_sys_bpf+0x73/0xb0 kernel/bpf/syscall.c:3355 do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294 entry_SYSCALL_64_after_hwframe+0x49/0xbe Possible unsafe locking scenario: CPU0 CPU2 ---- ---- lock(&htab->buckets[i].lock#2); lock(&l->lock); lock(&htab->buckets[i].lock#2); lock(&loc_l->lock); *** DEADLOCK *** To fix the issue, for htab_lru_map_lookup_and_delete_batch() in CPU0, let us do bpf_lru_push_free() out of the htab bucket lock. This can avoid the above deadlock scenario. Fixes: 057996380a42 ("bpf: Add batch ops to all htab bpf map") Reported-by: syzbot+a38ff3d9356388f2fb83@syzkaller.appspotmail.com Reported-by: syzbot+122b5421d14e68f29cd1@syzkaller.appspotmail.com Suggested-by: Hillf Danton <hdanton@sina.com> Suggested-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Acked-by: Brian Vazquez <brianvv@google.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/bpf/20200219234757.3544014-1-yhs@fb.com
2020-02-19bpf: Do not grab the bucket spinlock by default on htab batch opsBrian Vazquez1-2/+22
Grabbing the spinlock for every bucket even if it's empty, was causing significant perfomance cost when traversing htab maps that have only a few entries. This patch addresses the issue by checking first the bucket_cnt, if the bucket has some entries then we go and grab the spinlock and proceed with the batching. Tested with a htab of size 50K and different value of populated entries. Before: Benchmark Time(ns) CPU(ns) --------------------------------------------- BM_DumpHashMap/1 2759655 2752033 BM_DumpHashMap/10 2933722 2930825 BM_DumpHashMap/200 3171680 3170265 BM_DumpHashMap/500 3639607 3635511 BM_DumpHashMap/1000 4369008 4364981 BM_DumpHashMap/5k 11171919 11134028 BM_DumpHashMap/20k 69150080 69033496 BM_DumpHashMap/39k 190501036 190226162 After: Benchmark Time(ns) CPU(ns) --------------------------------------------- BM_DumpHashMap/1 202707 200109 BM_DumpHashMap/10 213441 210569 BM_DumpHashMap/200 478641 472350 BM_DumpHashMap/500 980061 967102 BM_DumpHashMap/1000 1863835 1839575 BM_DumpHashMap/5k 8961836 8902540 BM_DumpHashMap/20k 69761497 69322756 BM_DumpHashMap/39k 187437830 186551111 Fixes: 057996380a42 ("bpf: Add batch ops to all htab bpf map") Signed-off-by: Brian Vazquez <brianvv@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20200218172552.215077-1-brianvv@google.com
2020-02-19ice: Wait for VF to be reset/ready before configurationBrett Creeley2-61/+76
The configuration/command below is failing when the VF in the xml file is already bound to the host iavf driver. pci_0000_af_0_0.xml: <interface type='hostdev' managed='yes'> <source> <address type='pci' domain='0x0000' bus='0xaf' slot='0x0' function='0x0'/> </source> <mac address='00:de:ad:00:11:01'/> </interface> > virsh attach-device domain_name pci_0000_af_0_0.xml error: Failed to attach device from pci_0000_af_0_0.xml error: Cannot set interface MAC/vlanid to 00:de:ad:00:11:01/0 for ifname ens1f1 vf 0: Device or resource busy This is failing because the VF has not been completely removed/reset after being unbound (via the virsh command above) from the host iavf driver and ice_set_vf_mac() checks if the VF is disabled before waiting for the reset to finish. Fix this by waiting for the VF remove/reset process to happen before checking if the VF is disabled. Also, since many functions for VF administration on the PF were more or less calling the same 3 functions (ice_wait_on_vf_reset(), ice_is_vf_disabled(), and ice_check_vf_init()) move these into the helper function ice_check_vf_ready_for_cfg(). Then call this function in any flow that attempts to configure/query a VF from the PF. Lastly, increase the maximum wait time in ice_wait_on_vf_reset() to 800ms, and modify/add the #define(s) that determine the wait time. This was done for robustness because in rare/stress cases VF removal can take a max of ~800ms and previously the wait was a max of ~300ms. Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-02-19ice: Don't tell the OS that link is going downMichal Swiatkowski1-7/+0
Remove code that tell the OS that link is going down when user change flow control via ethtool. When link is up it isn't certain that link goes down after 0x0605 aq command. If link doesn't go down, OS thinks that link is down, but physical link is up. To reset this state user have to take interface down and up. If link goes down after 0x0605 command, FW send information about that and after that driver tells the OS that the link goes down. So this code in ethtool is unnecessary. Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-02-19ice: Don't reject odd values of usecs set by userBrett Creeley2-12/+39
Currently if a user sets an odd [tx|rx]-usecs value through ethtool, the request is denied because the hardware is set to have an ITR granularity of 2us. This caused poor customer experience. Fix this by aligning to a register allowed value, which results in rounding down. Also, print a once per ring container type message to be clear about our intentions. Also, change the ITR_TO_REG define to be the bitwise and of the ITR setting and the ICE_ITR_MASK. This makes the purpose of ITR_TO_REG more obvious. Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-02-19bridge: br_stp: Use built-in RCU list checkingMadhuparna Bhowmik1-1/+2
list_for_each_entry_rcu() has built-in RCU and lock checking. Pass cond argument to list_for_each_entry_rcu() to silence false lockdep warning when CONFIG_PROVE_RCU_LIST is enabled by default. Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-19nfc: pn544: Fix occasional HW initialization failureDmitry Osipenko1-0/+1
The PN544 driver checks the "enable" polarity during of driver's probe and it's doing that by turning ON and OFF NFC with different polarities until enabling succeeds. It takes some time for the hardware to power-down, and thus, to deassert the IRQ that is raised by turning ON the hardware. Since the delay after last power-down of the polarity-checking process is missed in the code, the interrupt may trigger immediately after installing the IRQ handler (right after the checking is done), which results in IRQ handler trying to touch the disabled HW and ends with marking NFC as 'DEAD' during of the driver's probe: pn544_hci_i2c 1-002a: NFC: nfc_en polarity : active high pn544_hci_i2c 1-002a: NFC: invalid len byte shdlc: llc_shdlc_recv_frame: NULL Frame -> link is dead This patch fixes the occasional NFC initialization failure on Nexus 7 device. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-19net: hsr: Pass lockdep expression to RCU listsAmol Grover1-1/+2
node_db is traversed using list_for_each_entry_rcu outside an RCU read-side critical section but under the protection of hsr->list_lock. Hence, add corresponding lockdep expression to silence false-positive warnings, and harden RCU lists. Signed-off-by: Amol Grover <frextrite@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-19Merge tag 'mlx5-fixes-2020-02-18' of ↵David S. Miller11-29/+70
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== Mellanox, mlx5 fixes 2020-02-18 This series introduces some fixes to mlx5 driver. Please pull and let me know if there is any problem. For -stable v5.3 ('net/mlx5: Fix sleep while atomic in mlx5_eswitch_get_vepa') For -stable v5.4 ('net/mlx5: DR, Fix matching on vport gvmi') ('net/mlx5e: Fix crash in recovery flow without devlink reporter') For -stable v5.5 ('net/mlx5e: Reset RQ doorbell counter before moving RQ state from RST to RDY') ('net/mlx5e: Don't clear the whole vf config when switching modes') ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-18net/mlx5: DR, Handle reformat capability over sw-steering tablesErez Shitrit2-3/+11
On flow table creation, send the relevant flags according to what the FW currently supports. When FW doesn't support reformat option over SW-steering managed table, the driver shouldn't pass this. Fixes: 988fd6b32d07 ("net/mlx5: DR, Pass table flags at creation to lower layer") Signed-off-by: Erez Shitrit <erezsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-02-18net/mlx5: Fix lowest FDB pool sizePaul Blakey1-1/+1
The pool sizes represent the pool sizes in the fw. when we request a pool size from fw, it will return the next possible group. We track how many pools the fw has left and start requesting groups from the big to the small. When we start request 4k group, which doesn't exists in fw, fw wants to allocate the next possible size, 64k, but will fail since its exhausted. The correct smallest pool size in fw is 128 and not 4k. Fixes: 39ac237ce009 ("net/mlx5: E-Switch, Refactor chains and priorities") Signed-off-by: Paul Blakey <paulb@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-02-18net/mlx5e: Don't clear the whole vf config when switching modesDmytro Linkin2-3/+7
There is no need to reset all vf config (except link state) between legacy and switchdev modes changes. Also, set link state to AUTO, when legacy enabled. Fixes: 3b83b6c2e024 ("net/mlx5e: Clear VF config when switching modes") Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-02-18net/mlx5: DR, Fix matching on vport gvmiHamdan Igbaria1-1/+4
Set vport gvmi in the tag, only when source gvmi is set in the bit mask. Fixes: 26d688e3 ("net/mlx5: DR, Add Steering entry (STE) utilities") Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com> Reviewed-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-02-18net/mlx5e: Fix crash in recovery flow without devlink reporterAya Levin1-1/+1
When health reporters are not supported, recovery function is invoked directly, not via devlink health reporters. In this direct flow, the recover function input parameter was passed incorrectly and is causing a kernel oops. This patch is fixing the input parameter. Following call trace is observed on rx error health reporting. Internal error: Oops: 96000007 [#1] PREEMPT SMP Process kworker/u16:4 (pid: 4584, stack limit = 0x00000000c9e45703) Call trace: mlx5e_rx_reporter_err_rq_cqe_recover+0x30/0x164 [mlx5_core] mlx5e_health_report+0x60/0x6c [mlx5_core] mlx5e_reporter_rq_cqe_err+0x6c/0x90 [mlx5_core] mlx5e_rq_err_cqe_work+0x20/0x2c [mlx5_core] process_one_work+0x168/0x3d0 worker_thread+0x58/0x3d0 kthread+0x108/0x134 Fixes: c50de4af1d63 ("net/mlx5e: Generalize tx reporter's functionality") Signed-off-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-02-18net/mlx5e: Reset RQ doorbell counter before moving RQ state from RST to RDYAya Levin4-9/+43
Initialize RQ doorbell counters to zero prior to moving an RQ from RST to RDY state. Per HW spec, when RQ is back to RDY state, the descriptor ID on the completion is reset. The doorbell record must comply. Fixes: 8276ea1353a4 ("net/mlx5e: Report and recover from CQE with error on RQ") Signed-off-by: Aya Levin <ayal@mellanox.com> Reported-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-02-18net/mlx5: Fix sleep while atomic in mlx5_eswitch_get_vepaHuy Nguyen1-11/+3
rtnl_bridge_getlink is protected by rcu lock, so mlx5_eswitch_get_vepa cannot take mutex lock. Two possible issues can happen: 1. User at the same time change vepa mode via RTM_SETLINK command. 2. User at the same time change the switchdev mode via devlink netlink interface. Case 1 cannot happen because rtnl executes one message in order. Case 2 can happen but we do not expect user to change the switchdev mode when changing vepa. Even if a user does it, so he will read a value which is no longer valid. Fixes: 8da202b24913 ("net/mlx5: E-Switch, Add support for VEPA in legacy mode.") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-02-18Merge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller7-45/+220
Pablo Neira Ayuso says: ==================== Netfilter fixes for net This batch contains Netfilter fixes for net: 1) Restrict hashlimit size to 1048576, from Cong Wang. 2) Check for offload flags from nf_flow_table_offload_setup(), this fixes a crash in case the hardware offload is disabled. From Florian Westphal. 3) Three preparation patches to extend the conntrack clash resolution, from Florian. 4) Extend clash resolution to deal with DNS packets from the same flow racing to set up the NAT configuration. 5) Small documentation fix in pipapo, from Stefano Brivio. 6) Remove misleading unlikely() from pipapo_refill(), also from Stefano. 7) Reduce hashlimit mutex scope, from Cong Wang. This patch is actually triggering another problem, still under discussion, another patch to fix this will follow up. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-18netfilter: nft_set_pipapo: Don't abuse unlikely() in pipapo_refill()Stefano Brivio1-1/+1
I originally used unlikely() in the if (match_only) clause, which we hit on the mapping table for the last field in a set, to ensure we avoid branching to the rest of for loop body, which is executed more frequently. However, Pablo reports, this is confusing as it gives the impression that this is not a common case, and it's actually not the intended usage of unlikely(). I couldn't observe any statistical difference in matching rates on x864_64 and aarch64 without it, so just drop it. Reported-by: Pablo Neira Ayuso <pablo@netfilter.org> Fixes: 3c4287f62044 ("nf_tables: Add set type for arbitrary concatenation of ranges") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-02-18netfilter: nft_set_pipapo: Fix mapping table example in commentsStefano Brivio1-2/+2
In both insertion and lookup examples, the two element pointers of rule mapping tables were swapped. Fix that. Reported-by: Pablo Neira Ayuso <pablo@netfilter.org> Fixes: 3c4287f62044 ("nf_tables: Add set type for arbitrary concatenation of ranges") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-02-18flow_table.c: Use built-in RCU list checkingMadhuparna Bhowmik1-2/+4
hlist_for_each_entry_rcu() has built-in RCU and lock checking. Pass cond argument to list_for_each_entry_rcu() to silence false lockdep warning when CONFIG_PROVE_RCU_LIST is enabled by default. Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-18datapath.c: Use built-in RCU list checkingMadhuparna Bhowmik1-3/+6
hlist_for_each_entry_rcu() has built-in RCU and lock checking. Pass cond argument to list_for_each_entry_rcu() to silence false lockdep warning when CONFIG_PROVE_RCU_LIST is enabled by default. Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-18vport.c: Use built-in RCU list checkingMadhuparna Bhowmik1-1/+2
hlist_for_each_entry_rcu() has built-in RCU and lock checking. Pass cond argument to list_for_each_entry_rcu() to silence false lockdep warning when CONFIG_PROVE_RCU_LIST is enabled by default. Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-18meter.c: Use built-in RCU list checkingMadhuparna Bhowmik1-1/+2
hlist_for_each_entry_rcu() has built-in RCU and lock checking. Pass cond argument to list_for_each_entry_rcu() to silence false lockdep warning when CONFIG_PROVE_RCU_LIST is enabled by default. Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-18netlabel_domainhash.c: Use built-in RCU list checkingMadhuparna Bhowmik1-1/+2
list_for_each_entry_rcu() has built-in RCU and lock checking. Pass cond argument to list_for_each_entry_rcu() to silence false lockdep warning when CONFIG_PROVE_RCU_LIST is enabled by default. Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-18net: netlabel: Use built-in RCU list checkingMadhuparna Bhowmik1-1/+2
list_for_each_entry_rcu() has built-in RCU and lock checking. Pass cond argument to list_for_each_entry_rcu() to silence false lockdep warning when CONFIG_PROVE_RCU_LIST is enabled by default. Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-18Revert "net: dev: introduce support for sch BYPASS for lockless qdisc"Paolo Abeni1-20/+2
This reverts commit ba27b4cdaaa66561aaedb2101876e563738d36fe Ahmed reported ouf-of-order issues bisected to commit ba27b4cdaaa6 ("net: dev: introduce support for sch BYPASS for lockless qdisc"). I can't find any working solution other than a plain revert. This will introduce some minor performance regressions for pfifo_fast qdisc. I plan to address them in net-next with more indirect call wrapper boilerplate for qdiscs. Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Fixes: ba27b4cdaaa6 ("net: dev: introduce support for sch BYPASS for lockless qdisc") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-18net: phy: broadcom: Fix a typo ("firsly")Jonathan Neuschäfer1-2/+2
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-18mptcp: fix bogus socket flag valuesFlorian Westphal1-2/+2
Dan Carpenter reports static checker warnings due to bogus BIT() usage: net/mptcp/subflow.c:571 subflow_write_space() warn: test_bit() takes a bit number net/mptcp/subflow.c:694 subflow_state_change() warn: test_bit() takes a bit number net/mptcp/protocol.c:261 ssk_check_wmem() warn: test_bit() takes a bit number [..] This is harmless (we use bits 1 & 2 instead of 0 and 1), but would break eventually when adding BIT(5) (or 6, depends on size of 'long'). Just use 0 and 1, the values are only passed to test/set/clear_bit functions. Fixes: 648ef4b88673 ("mptcp: Implement MPTCP receive path") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-18qede: Fix race between rdma destroy workqueue and link change eventMichal Kalderon2-1/+30
If an event is added while the rdma workqueue is being destroyed it could lead to several races, list corruption, null pointer dereference during queue_work or init_queue. This fixes the race between the two flows which can occur during shutdown. A kref object and a completion object are added to the rdma_dev structure, these are initialized before the workqueue is created. The refcnt is used to indicate work is being added to the workqueue and ensures the cleanup flow won't start while we're in the middle of adding the event. Once the work is added, the refcnt is decreased and the cleanup flow is safe to run. Fixes: cee9fbd8e2e ("qede: Add qedr framework") Signed-off-by: Ariel Elior <ariel.elior@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-18libbpf: Sanitise internal map names so they are not rejected by the kernelToke Høiland-Jørgensen1-1/+7
The kernel only accepts map names with alphanumeric characters, underscores and periods in their name. However, the auto-generated internal map names used by libbpf takes their prefix from the user-supplied BPF object name, which has no such restriction. This can lead to "Invalid argument" errors when trying to load a BPF program using global variables. Fix this by sanitising the map names, replacing any non-allowed characters with underscores. Fixes: d859900c4c56 ("bpf, libbpf: support global data/bss/rodata sections") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20200217171701.215215-1-toke@redhat.com
2020-02-18bpf, uapi: Remove text about bpf_redirect_map() giving higher performanceToke Høiland-Jørgensen2-18/+14
The performance of bpf_redirect() is now roughly the same as that of bpf_redirect_map(). However, David Ahern pointed out that the header file has not been updated to reflect this, and still says that a significant performance increase is possible when using bpf_redirect_map(). Remove this text from the bpf_redirect_map() description, and reword the description in bpf_redirect() slightly. Also fix the 'Return' section of the bpf_redirect_map() documentation. Fixes: 1d233886dd90 ("xdp: Use bulking for non-map XDP_REDIRECT and consolidate code paths") Reported-by: David Ahern <dsahern@gmail.com> Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Quentin Monnet <quentin@isovalent.com> Link: https://lore.kernel.org/bpf/20200218130334.29889-1-toke@redhat.com
2020-02-17selftests: forwarding: vxlan_bridge_1d: use more proper tos valueHangbin Liu1-3/+3
0x11 and 0x12 set the ECN bits based on RFC2474, it would be better to avoid that. 0x14 and 0x18 would be better and works as well. Reported-by: Petr Machata <petrm@mellanox.com> Fixes: 4e867c9a50ff ("selftests: forwarding: vxlan_bridge_1d: fix tos value") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-17net: cnic: fix spelling mistake "reserverd" -> "reserved"Alexandre Belloni1-2/+2
The reserved member should be named reserved3. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-17sctp: move the format error check out of __sctp_sf_do_9_1_abortXin Long1-9/+20
When T2 timer is to be stopped, the asoc should also be deleted, otherwise, there will be no chance to call sctp_association_free and the asoc could last in memory forever. However, in sctp_sf_shutdown_sent_abort(), after adding the cmd SCTP_CMD_TIMER_STOP for T2 timer, it may return error due to the format error from __sctp_sf_do_9_1_abort() and miss adding SCTP_CMD_ASSOC_FAILED where the asoc will be deleted. This patch is to fix it by moving the format error check out of __sctp_sf_do_9_1_abort(), and do it before adding the cmd SCTP_CMD_TIMER_STOP for T2 timer. Thanks Hangbin for reporting this issue by the fuzz testing. v1->v2: - improve the comment in the code as Marcelo's suggestion. Fixes: 96ca468b86b0 ("sctp: check invalid value of length parameter in error cause") Reported-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-19 21:21:49 +0000