summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2014-05-16ARM: dts: pbab01: Enable UART1Philipp Zabel1-0/+4
This patch enables UART1 on the phyFLEX connector (i.MX6 uart3). Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: pfla02: Add UART1 (uart3)Philipp Zabel1-0/+15
The pins labeled UART1 on the module connector are wired to i.MX6 uart3. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: pbab01: Add I2C devicesPhilipp Zabel1-0/+20
This patch adds the TLV320, STMPE811, RTC8564, and MX1037 ICs to the I2C2 bus. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: pbab01: Add I2C2 and I2C3Philipp Zabel1-0/+30
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: pbab01: Set linux,stdout-path to UART4Philipp Zabel1-0/+6
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: pfla02: PHY reset is active-lowPhilipp Zabel1-1/+3
Note that the fec driver code currently hard-codes an active-low reset, regardless of the flags in the device tree. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: pfla02: Add GPIO LEDsPhilipp Zabel1-0/+16
This patch enables the red and green GPIO LEDs on Phytec phyFLEX i.MX6 modules. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: Add Phytec pbab01 with i.MX6 DualLite/SoloPhilipp Zabel4-29/+60
The PBA-B-01 carrier board can be equipped with either Quad or DualLite/Solo phyFLEX i.MX6 modules (PFL-A-02). This moves all common devices into imx6qdl-phytec-pbab01.dtsi. The SoC specific device trees then just include the pfla01 and pbab01 dtsi files corresponding to the SoC variant. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: Add Phytec pfla02 with i.MX6 DualLite/SoloPhilipp Zabel3-305/+347
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx27-pdk: Pass the FEC pin configurationFabio Estevam1-0/+26
Provide an entry for the FEC pin muxing. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx27-pdk: Pass the UART1 pin configurationFabio Estevam1-0/+15
Provide an entry for the UART1 pin muxing. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx27-pdk: Keep the dt nodes sortedFabio Estevam1-3/+4
For better readability keep the dt nodes sorted. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM i.MX51: Add Digi ConnectCore devicetreeAlexander Shiyan3-0/+488
This patch adds support for Digi ConnectCore® i.MX51/Wi-i.MX51 SOM and basic support for the ConnectCore for i.MX51 JumpStart Kit. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: i.MX: Use single naming style for i.MX WEIM deviceAlexander Shiyan2-3/+3
This patch converts all i.MX WEIM users to use single naming style for devices. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: cpuimx51 Add touchscreen support.Denis Carikli1-0/+11
Signed-off-by: Denis Carikli <denis@eukrea.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: cpuimx35 Add touchscreen support.Denis Carikli1-0/+15
Signed-off-by: Denis Carikli <denis@eukrea.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: mbimxsd51 baseboard: Add USB support.Denis Carikli1-0/+58
Signed-off-by: Denis Carikli <denis@eukrea.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: add initial Colibri VF61 board supportStefan Agner2-0/+124
Add initial Toradex Colibri VF61 board support. Ethernet, UART and SDHC cards are working. Cache latencies need to be a bit higher than vf610.dtsi suggests. Those values are validated by running multiple memory tests. Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16of: add vendor prefix for Toradex AGStefan Agner1-0/+1
Adds toradex to the list of DT vendor prefixes. Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx27-pdk: Pass the memory rangeFabio Estevam1-1/+1
imx27-pdk has 128 MB of DRAM. Pass the memory range in dt. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx27-phytec-phycore-rdk: Add display control signal definitionsAlexander Shiyan1-0/+4
This patch adds display control signal definitions. These fields are not used in the driver yet, but will be used for reference to indicate the polarity of the signals. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx28-duckbill: use symbolic names from gpio.hMichael Heimpold1-2/+2
Use GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW instead of 0 and 1. Signed-off-by: Michael Heimpold <mhei@heimpold.de> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx28-duckbill: fix phy reset gpioMichael Heimpold1-2/+2
Fix a copy & paste error: on duckbills the GPIO used for resetting the ethernet phy differs from FSL's MX28EVK board. Reported-by: Stefan Wahren <info@lategoodbye.de> Signed-off-by: Michael Heimpold <mhei@heimpold.de> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx28: include gpio.h to allow use of symbolic namesMichael Heimpold1-0/+1
Signed-off-by: Michael Heimpold <mhei@heimpold.de> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx28-duckbill: fix mmc settingsMichael Heimpold1-2/+2
I2SE's duckbills are only equipped with a micro SD card slot and thus only provide a 4-bit interface. Signed-off-by: Michael Heimpold <mhei@heimpold.de> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx51-babbage: Add USB OTG supportFabio Estevam1-0/+7
Tested by pinging from the host PC to the imx51-babbage via a g_ether connection. Signed-off by: Dave Ebright <dave.ebright@parsons.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx51-babbage: Add USB Host1 supportFabio Estevam1-0/+55
Signed-off by: Dave Ebright <dave.ebright@parsons.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx35-pdk: Add initial device tree supportFabio Estevam2-0/+68
Add support for UART, eSDHC and NAND. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: vf610-twr: Enables FTM PWM device.Xiubo Li1-0/+6
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Yuan Yao <yao.yuan@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: vf610-twr: Add PWM0's pinctrl nodeXiubo Li1-0/+11
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: vf610: Add Freescale FTM PWM node.Xiubo Li1-0/+13
This adds devicetree node for VF610, and there are 8 channels supported. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Yuan Yao <yao.yuan@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: i.MX53: Add reset line to VPU device nodePhilipp Zabel1-0/+1
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: i.MX53: Enable CODA7541 VPUPhilipp Zabel1-1/+0
This IP module is always present and has no external connections. There is no reason to disable it in the device tree. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx25-pdk: Add USB Host1 supportFabio Estevam1-0/+6
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx27-phytec-phycore-rdk: Add display supportAlexander Shiyan1-0/+64
This patch adds FB, Sharp-LQ035Q7 display (add-on module) and corresponded pinctrl devicetree nodes to the Phytec PCM970 RDK. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx25-pdk: Add CAN supportFabio Estevam1-0/+23
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx25-pdk: Add keypad supportFabio Estevam2-1/+41
Tested with evtest. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-05-16ARM: dts: imx25-pdk: Add audio supportFabio Estevam1-0/+74
mx25pdk has a sgtl5000 codec connected to the I2C1 port. Add support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-04-30ARM: dts: mbimxsd35 baseboard: Add USB support.Denis Carikli1-0/+13
Signed-off-by: Denis Carikli <denis@eukrea.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-04-30ARM: dts: i.MX35: Add USB support.Denis Carikli1-0/+18
Signed-off-by: Denis Carikli <denis@eukrea.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-04-30ARM: dts: mbimxsd25 baseboard: Add USB supportDenis Carikli1-0/+13
Signed-off-by: Denis Carikli <denis@eukrea.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-04-30ARM: dts: imx25.dtsi: Fix USB support.Fabio Estevam1-11/+18
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Denis Carikli <denis@eukrea.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-04-30ARM: dts: mx35: USB block requires only one clockFabio Estevam1-4/+2
Like other imx SoCs only one USB clock is needed on mx35. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-04-30ARM: dts: mx25: USB block requires only one clockFabio Estevam1-4/+2
Like other imx SoCs only one USB clock is needed on mx25. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-04-30ARM: dts: vf610-twr: Add support for sdhc1Cosmin Stoica2-0/+30
The kernel was not able to boot from SD card because sdhc support was not present into the dts. A new entry for sdhc1 was added for vf610-twr board based on the compatible entry present on imx53. After applying these changes, the kernel is able to boot successfully from SD card. Signed-off-by: Cosmin Stoica <cosminstefan.stoica@freescale.com> Signed-off-by: Chircu Bogdan <Bogdan.Chircu@freescale.com> Signed-off-by: Eddy Petrisor <eddy.petrisor@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2014-04-30ARM: dts: imx25-pdk: Add esdhc1 supportFabio Estevam1-0/+21
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2014-04-30ARM: dts: imx25-pdk: Provide an Ethernet PHY resetFabio Estevam1-0/+2
GPIO4_8 is connected to the Ethernet PHY reset line, so populate the 'phy-reset-gpios' property accordingly. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2014-04-30ARM: dts: imx25-pdk: Provide a regulator for Ethernet PHYFabio Estevam1-0/+18
GPIO2_3 controls the power to the Ethernet PHY, so provide a regulator node for this. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2014-04-30ARM: dts: imx25-pdk: Add FEC pinsFabio Estevam1-0/+16
Instead of relying on the bootloader for configuring the FEC pins, pass the FEC pin configuration via device tree instead. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2014-04-30ARM: dts: imx25-pdk: Add UART1 pinsFabio Estevam1-0/+16
UART1 is the console port on mx25pdk board. Add the pin configuration for UART1 port and also pass 'fsl,uart-has-rtscts' to indicate that the port has RTS and CTS pins. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-10-14 14:26:45 +0000