summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2019-05-20vlan: Mark expected switch fall-throughGustavo A. R. Silva1-0/+1
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. This patch fixes the following warning: net/8021q/vlan_dev.c: In function ‘vlan_dev_ioctl’: net/8021q/vlan_dev.c:374:6: warning: this statement may fall through [-Wimplicit-fallthrough=] if (!net_eq(dev_net(dev), &init_net)) ^ net/8021q/vlan_dev.c:376:2: note: here case SIOCGMIIPHY: ^~~~ Warning level 3 was used: -Wimplicit-fallthrough=3 This patch is part of the ongoing efforts to enable -Wimplicit-fallthrough. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-20macvlan: Mark expected switch fall-throughGustavo A. R. Silva1-0/+1
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. This patch fixes the following warning: drivers/net/macvlan.c: In function ‘macvlan_do_ioctl’: drivers/net/macvlan.c:839:6: warning: this statement may fall through [-Wimplicit-fallthrough=] if (!net_eq(dev_net(dev), &init_net)) ^ drivers/net/macvlan.c:841:2: note: here case SIOCGHWTSTAMP: ^~~~ Warning level 3 was used: -Wimplicit-fallthrough=3 This patch is part of the ongoing efforts to enable -Wimplicit-fallthrough. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-20net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages queryErez Alfasi2-6/+3
Querying EEPROM high pages data for SFP module is currently not supported by our driver but is still tried, resulting in invalid FW queries. Set the EEPROM ethtool data length to 256 for SFP module to limit the reading for page 0 only and prevent invalid FW queries. Fixes: 7202da8b7f71 ("ethtool, net/mlx4_en: Cable info, get_module_info/eeprom ethtool support") Signed-off-by: Erez Alfasi <ereza@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-20tipc: fix modprobe tipc failed after switch order of device registrationJunwei Hu3-10/+27
Error message printed: modprobe: ERROR: could not insert 'tipc': Address family not supported by protocol. when modprobe tipc after the following patch: switch order of device registration, commit 7e27e8d6130c ("tipc: switch order of device registration to fix a crash") Because sock_create_kern(net, AF_TIPC, ...) called by tipc_topsrv_create_listener() in the initialization process of tipc_init_net(), so tipc_socket_init() must be execute before that. Meanwhile, tipc_net_id need to be initialized when sock_create() called, and tipc_socket_init() is no need to be called for each namespace. I add a variable tipc_topsrv_net_ops, and split the register_pernet_subsys() of tipc into two parts, and split tipc_socket_init() with initialization of pernet params. By the way, I fixed resources rollback error when tipc_bcast_init() failed in tipc_init_net(). Fixes: 7e27e8d6130c ("tipc: switch order of device registration to fix a crash") Signed-off-by: Junwei Hu <hujunwei4@huawei.com> Reported-by: Wang Wang <wangwang2@huawei.com> Reported-by: syzbot+1e8114b61079bfe9cbc5@syzkaller.appspotmail.com Reviewed-by: Kang Zhou <zhoukang7@huawei.com> Reviewed-by: Suanming Mou <mousuanming@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-20Merge tag 'for-5.2-rc1-tag' of ↵Linus Torvalds8-26/+97
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux Pull btrfs fixes from David Sterba: "Notable highlights: - fixes for some long-standing bugs in fsync that were quite hard to catch but now finaly fixed - some fixups to error handling paths that did not properly clean up (locking, memory) - fix to space reservation for inheriting properties" * tag 'for-5.2-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: Btrfs: tree-checker: detect file extent items with overlapping ranges Btrfs: fix race between ranged fsync and writeback of adjacent ranges Btrfs: avoid fallback to transaction commit during fsync of files with holes btrfs: extent-tree: Fix a bug that btrfs is unable to add pinned bytes btrfs: sysfs: don't leak memory when failing add fsid btrfs: sysfs: Fix error path kobject memory leak Btrfs: do not abort transaction at btrfs_update_root() after failure to COW path btrfs: use the existing reserved items for our first prop for inheritance btrfs: don't double unlock on error in btrfs_punch_hole btrfs: Check the compression level before getting a workspace
2019-05-20Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds93-416/+874
Pull networking fixes from David Miller:1) Use after free in __dev_map_entry_free(), from Eric Dumazet. 1) Use after free in __dev_map_entry_free(), from Eric Dumazet. 2) Fix TCP retransmission timestamps on passive Fast Open, from Yuchung Cheng. 3) Orphan NFC, we'll take the patches directly into my tree. From Johannes Berg. 4) We can't recycle cloned TCP skbs, from Eric Dumazet. 5) Some flow dissector bpf test fixes, from Stanislav Fomichev. 6) Fix RCU marking and warnings in rhashtable, from Herbert Xu. 7) Fix some potential fib6 leaks, from Eric Dumazet. 8) Fix a _decode_session4 uninitialized memory read bug fix that got lost in a merge. From Florian Westphal. 9) Fix ipv6 source address routing wrt. exception route entries, from Wei Wang. 10) The netdev_xmit_more() conversion was not done %100 properly in mlx5 driver, fix from Tariq Toukan. 11) Clean up botched merge on netfilter kselftest, from Florian Westphal. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (74 commits) of_net: fix of_get_mac_address retval if compiled without CONFIG_OF net: fix kernel-doc warnings for socket.c net: Treat sock->sk_drops as an unsigned int when printing kselftests: netfilter: fix leftover net/net-next merge conflict mlxsw: core: Prevent reading unsupported slave address from SFP EEPROM mlxsw: core: Prevent QSFP module initialization for old hardware vsock/virtio: Initialize core virtio vsock before registering the driver net/mlx5e: Fix possible modify header actions memory leak net/mlx5e: Fix no rewrite fields with the same match net/mlx5e: Additional check for flow destination comparison net/mlx5e: Add missing ethtool driver info for representors net/mlx5e: Fix number of vports for ingress ACL configuration net/mlx5e: Fix ethtool rxfh commands when CONFIG_MLX5_EN_RXNFC is disabled net/mlx5e: Fix wrong xmit_more application net/mlx5: Fix peer pf disable hca command net/mlx5: E-Switch, Correct type to u16 for vport_num and int for vport_index net/mlx5: Add meaningful return codes to status_to_err function net/mlx5: Imply MLXFW in mlx5_core Revert "tipc: fix modprobe tipc failed after switch order of device registration" vsock/virtio: free packets during the socket release ...
2019-05-19Linux 5.2-rc1v5.2-rc1Linus Torvalds1-2/+2
2019-05-19Merge tag 'upstream-5.2-rc2' of ↵Linus Torvalds3-4/+8
git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs Pull UBIFS fixes from Richard Weinberger: - build errors wrt xattrs - mismerge which lead to a wrong Kconfig ifdef - missing endianness conversion * tag 'upstream-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs: ubifs: Convert xattr inum to host order ubifs: Use correct config name for encryption ubifs: Fix build error without CONFIG_UBIFS_FS_XATTR
2019-05-19Merge branch 'akpm' (patches from Andrew)Linus Torvalds10-257/+889
Merge yet more updates from Andrew Morton: "A few final bits: - large changes to vmalloc, yielding large performance benefits - tweak the console-flush-on-panic code - a few fixes" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: panic: add an option to replay all the printk message in buffer initramfs: don't free a non-existent initrd fs/writeback.c: use rcu_barrier() to wait for inflight wb switches going into workqueue when umount mm/compaction.c: correct zone boundary handling when isolating pages from a pageblock mm/vmap: add DEBUG_AUGMENT_LOWEST_MATCH_CHECK macro mm/vmap: add DEBUG_AUGMENT_PROPAGATE_CHECK macro mm/vmalloc.c: keep track of free blocks for vmap allocation
2019-05-19Merge tag 'kbuild-v5.2-2' of ↵Linus Torvalds74-172/+178
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull more Kbuild updates from Masahiro Yamada: - remove unneeded use of cc-option, cc-disable-warning, cc-ldoption - exclude tracked files from .gitignore - re-enable -Wint-in-bool-context warning - refactor samples/Makefile - stop building immediately if syncconfig fails - do not sprinkle error messages when $(CC) does not exist - move arch/alpha/defconfig to the configs subdirectory - remove crappy header search path manipulation - add comment lines to .config to clarify the end of menu blocks - check uniqueness of module names (adding new warnings intentionally) * tag 'kbuild-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (24 commits) kconfig: use 'else ifneq' for Makefile to improve readability kbuild: check uniqueness of module names kconfig: Terminate menu blocks with a comment in the generated config kbuild: add LICENSES to KBUILD_ALLDIRS kbuild: remove 'addtree' and 'flags' magic for header search paths treewide: prefix header search paths with $(srctree)/ media: prefix header search paths with $(srctree)/ media: remove unneeded header search paths alpha: move arch/alpha/defconfig to arch/alpha/configs/defconfig kbuild: terminate Kconfig when $(CC) or $(LD) is missing kbuild: turn auto.conf.cmd into a mandatory include file .gitignore: exclude .get_maintainer.ignore and .gitattributes kbuild: add all Clang-specific flags unconditionally kbuild: Don't try to add '-fcatch-undefined-behavior' flag kbuild: add some extra warning flags unconditionally kbuild: add -Wvla flag unconditionally arch: remove dangling asm-generic wrappers samples: guard sub-directories with CONFIG options kbuild: re-enable int-in-bool-context warning MAINTAINERS: kbuild: Add pattern for scripts/*vmlinux* ...
2019-05-19Merge branch 'i2c/for-next' of ↵Linus Torvalds3-13/+111
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c updates from Wolfram Sang: "Some I2C core API additions which are kind of simple but enhance error checking for users a lot, especially by returning errno now. There are wrappers to still support the old API but it will be removed once all users are converted" * 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: core: add device-managed version of i2c_new_dummy i2c: core: improve return value handling of i2c_new_device and i2c_new_dummy
2019-05-19Merge tag 'ext4_for_linus_stable' of ↵Linus Torvalds13-65/+107
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4 Pull ext4 fixes from Ted Ts'o: "Some bug fixes, and an update to the URL's for the final version of Unicode 12.1.0" * tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: avoid panic during forced reboot due to aborted journal ext4: fix block validity checks for journal inodes using indirect blocks unicode: update to Unicode 12.1.0 final unicode: add missing check for an error return from utf8lookup() ext4: fix miscellaneous sparse warnings ext4: unsigned int compared against zero ext4: fix use-after-free in dx_release() ext4: fix data corruption caused by overlapping unaligned and aligned IO jbd2: fix potential double free ext4: zero out the unused memory region in the extent tree block
2019-05-19Merge tag '5.2-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6Linus Torvalds8-51/+173
Pull cifs fixes from Steve French: "Minor cleanup and fixes, one for stable, four rdma (smbdirect) related. Also adds SEEK_HOLE support" * tag '5.2-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6: cifs: add support for SEEK_DATA and SEEK_HOLE Fixed https://bugzilla.kernel.org/show_bug.cgi?id=202935 allow write on the same file cifs: Allocate memory for all iovs in smb2_ioctl cifs: Don't match port on SMBDirect transport cifs:smbd Use the correct DMA direction when sending data cifs:smbd When reconnecting to server, call smbd_destroy() after all MIDs have been called cifs: use the right include for signal_pending() smb3: trivial cleanup to smb2ops.c cifs: cleanup smb2ops.c and normalize strings smb3: display session id in debug data
2019-05-19Merge branch 'perf-core-for-linus' of ↵Linus Torvalds94-214/+5414
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull perf tooling updates from Ingo Molnar: "perf.data: - Streaming compression of perf ring buffer into PERF_RECORD_COMPRESSED user space records, resulting in ~3-5x perf.data file size reduction on variety of tested workloads what saves storage space on larger server systems where perf.data size can easily reach several tens or even hundreds of GiBs, especially when profiling with DWARF-based stacks and tracing of context switches. perf record: - Improve -user-regs/intr-regs suggestions to overcome errors perf annotate: - Remove hist__account_cycles() from callback, speeding up branch processing (perf record -b) perf stat: - Add a 'percore' event qualifier, e.g.: -e cpu/event=0,umask=0x3,percore=1/, that sums up the event counts for both hardware threads in a core. We can already do this with --per-core, but it's often useful to do this together with other metrics that are collected per hardware thread. I.e. now its possible to do this per-event, and have it mixed with other events not aggregated by core. arm64: - Map Brahma-B53 CPUID to cortex-a53 events. - Add Cortex-A57 and Cortex-A72 events. csky: - Add DWARF register mappings for libdw, allowing --call-graph=dwarf to work on the C-SKY arch. x86: - Add support for recording and printing XMM registers, available, for instance, on Icelake. - Add uncore_upi (Intel's "Ultra Path Interconnect" events) JSON support. UPI replaced the Intel QuickPath Interconnect (QPI) in Xeon Skylake-SP. Intel PT: - Fix instructions sampling rate. - Timestamp fixes. - Improve exported-sql-viewer GUI, allowing, for instance, to copy'n'paste the trees, useful for e-mailing" * 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (73 commits) perf stat: Support 'percore' event qualifier perf stat: Factor out aggregate counts printing perf tools: Add a 'percore' event qualifier perf docs: Add description for stderr perf intel-pt: Fix sample timestamp wrt non-taken branches perf intel-pt: Fix improved sample timestamp perf intel-pt: Fix instructions sampling rate perf regs x86: Add X86 specific arch__intr_reg_mask() perf parse-regs: Add generic support for arch__intr/user_reg_mask() perf parse-regs: Split parse_regs perf vendor events arm64: Add Cortex-A57 and Cortex-A72 events perf vendor events arm64: Map Brahma-B53 CPUID to cortex-a53 events perf vendor events arm64: Remove [[:xdigit:]] wildcard perf jevents: Remove unused variable perf test zstd: Fixup verbose mode output perf tests: Implement Zstd comp/decomp integration test perf inject: Enable COMPRESSED record decompression perf report: Implement perf.data record decompression perf record: Implement -z,--compression_level[=<n>] option perf report: Add stub processing of compressed events for -D ...
2019-05-19Merge branch 'timers-urgent-for-linus' of ↵Linus Torvalds12-136/+202
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull clocksource updates from Ingo Molnar: "Misc clocksource/clockevent driver updates that came in a bit late but are ready for v5.2" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: misc: atmel_tclib: Do not probe already used TCBs clocksource/drivers/timer-atmel-tcb: Convert tc_clksrc_suspend|resume() to static clocksource/drivers/tcb_clksrc: Rename the file for consistency clocksource/drivers/timer-atmel-pit: Rework Kconfig option clocksource/drivers/tcb_clksrc: Move Kconfig option ARM: at91: Implement clocksource selection clocksource/drivers/tcb_clksrc: Use tcb as sched_clock clocksource/drivers/tcb_clksrc: Stop depending on atmel_tclib ARM: at91: move SoC specific definitions to SoC folder clocksource/drivers/timer-milbeaut: Cleanup common register accesses clocksource/drivers/timer-milbeaut: Add shutdown function clocksource/drivers/timer-milbeaut: Fix to enable one-shot timer clocksource/drivers/tegra: Rework for compensation of suspend time clocksource/drivers/sp804: Add COMPILE_TEST to CONFIG_ARM_TIMER_SP804 clocksource/drivers/sun4i: Add a compatible for suniv dt-bindings: timer: Add Allwinner suniv timer
2019-05-19Merge branch 'irq-urgent-for-linus' of ↵Linus Torvalds38-229/+2511
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull IRQ chip updates from Ingo Molnar: "A late irqchips update: - New TI INTR/INTA set of drivers - Rewrite of the stm32mp1-exti driver as a platform driver - Update the IOMMU MSI mapping API to be RT friendly - A number of cleanups and other low impact fixes" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits) iommu/dma-iommu: Remove iommu_dma_map_msi_msg() irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg() irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg() irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg() irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg() iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts genirq/msi: Add a new field in msi_desc to store an IOMMU cookie arm64: arch_k3: Enable interrupt controller drivers irqchip/ti-sci-inta: Add msi domain support soc: ti: Add MSI domain bus support for Interrupt Aggregator irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings irqchip/ti-sci-intr: Add support for Interrupt Router driver dt-bindings: irqchip: Introduce TISCI Interrupt router bindings gpio: thunderx: Use the default parent apis for {request,release}_resources genirq: Introduce irq_chip_{request,release}_resource_parent() apis firmware: ti_sci: Add helper apis to manage resources firmware: ti_sci: Add RM mapping table for am654 firmware: ti_sci: Add support for IRQ management firmware: ti_sci: Add support for RM core ops ...
2019-05-19of_net: fix of_get_mac_address retval if compiled without CONFIG_OFPetr Štetiar1-1/+1
of_get_mac_address prior to commit d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") could return only valid pointer or NULL, after this change it could return only valid pointer or ERR_PTR encoded error value, but I've forget to change the return value of of_get_mac_address in case where the kernel is compiled without CONFIG_OF, so I'm doing so now. Cc: Mirko Lindner <mlindner@marvell.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Fixes: d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") Reported-by: Octavio Alvarez <octallk1@alvarezp.org> Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-19Merge branch 'efi-urgent-for-linus' of ↵Linus Torvalds1-2/+6
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull EFI fix from Ingo Molnar: "Fix an EFI-fb regression that affects certain x86 systems" * 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: fbdev/efifb: Ignore framebuffer memmap entries that lack any memory types
2019-05-19net: fix kernel-doc warnings for socket.cRandy Dunlap1-17/+17
Fix kernel-doc warnings by moving the kernel-doc notation to be immediately above the functions that it describes. Fixes these warnings for sock_sendmsg() and sock_recvmsg(): ../net/socket.c:658: warning: Excess function parameter 'sock' description in 'INDIRECT_CALLABLE_DECLARE' ../net/socket.c:658: warning: Excess function parameter 'msg' description in 'INDIRECT_CALLABLE_DECLARE' ../net/socket.c:889: warning: Excess function parameter 'sock' description in 'INDIRECT_CALLABLE_DECLARE' ../net/socket.c:889: warning: Excess function parameter 'msg' description in 'INDIRECT_CALLABLE_DECLARE' ../net/socket.c:889: warning: Excess function parameter 'flags' description in 'INDIRECT_CALLABLE_DECLARE' Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-19net: Treat sock->sk_drops as an unsigned int when printingPatrick Talbert6-6/+6
Currently, procfs socket stats format sk_drops as a signed int (%d). For large values this will cause a negative number to be printed. We know the drop count can never be a negative so change the format specifier to %u. Signed-off-by: Patrick Talbert <ptalbert@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-19Merge branch 'core-urgent-for-linus' of ↵Linus Torvalds9-26/+27
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull core fixes from Ingo Molnar: "This fixes a particularly thorny munmap() bug with MPX, plus fixes a host build environment assumption in objtool" * 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: objtool: Allow AR to be overridden with HOSTAR x86/mpx, mm/core: Fix recursive munmap() corruption
2019-05-19Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds25-124/+277
Pull ARM SoC late updates from Olof Johansson: "This is some material that we picked up into our tree late. Most of it are smaller fixes and additions, some defconfig updates due to recent development, etc. Code-wise the largest portion is a series of PM updates for the at91 platform, and those have been in linux-next a while through the at91 tree before we picked them up" * tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (29 commits) arm64: dts: sprd: Add clock properties for serial devices Opt out of scripts/get_maintainer.pl ARM: ixp4xx: Remove duplicated include from common.c soc: ixp4xx: qmgr: Fix an NULL vs IS_ERR() check in probe arm64: tegra: Disable XUSB support on Jetson TX2 arm64: tegra: Enable SMMU translation for PCI on Tegra186 arm64: tegra: Fix insecure SMMU users for Tegra186 arm64: tegra: Select ARM_GIC_PM amba: tegra-ahb: Mark PM functions as __maybe_unused ARM: dts: logicpd-som-lv: Fix MMC1 card detect ARM: mvebu: drop return from void function ARM: mvebu: prefix coprocessor operand with p ARM: mvebu: drop unnecessary label ARM: mvebu: fix a leaked reference by adding missing of_node_put ARM: socfpga_defconfig: enable LTC2497 ARM: mvebu: kirkwood: remove error message when retrieving mac address ARM: at91: sama5: make ov2640 as a module ARM: OMAP1: ams-delta: fix early boot crash when LED support is disabled ARM: at91: remove HAVE_FB_ATMEL for sama5 SoC as they use DRM soc/fsl/qe: Fix an error code in qe_pin_request() ...
2019-05-19Merge tag 'powerpc-5.2-2' of ↵Linus Torvalds4-5/+7
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fixes from Michael Ellerman: "One fix going back to stable, for a bug on 32-bit introduced when we added support for THREAD_INFO_IN_TASK. A fix for a typo in a recent rework of our hugetlb code that leads to crashes on 64-bit when using hugetlbfs with a 4K PAGE_SIZE. Two fixes for our recent rework of the address layout on 64-bit hash CPUs, both only triggered when userspace tries to access addresses outside the user or kernel address ranges. Finally a fix for a recently introduced double free in an error path in our cacheinfo code. Thanks to: Aneesh Kumar K.V, Christophe Leroy, Sachin Sant, Tobin C. Harding" * tag 'powerpc-5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/cacheinfo: Remove double free powerpc/mm/hash: Fix get_region_id() for invalid addresses powerpc/mm: Drop VM_BUG_ON in get_region_id() powerpc/mm: Fix crashes with hugepages & 4K pages powerpc/32s: fix flush_hash_pages() on SMP
2019-05-19Merge tag 'mips_5.2_2' of ↵Linus Torvalds18-659/+831
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux Pull a few more MIPS updates from Paul Burton: "Some SGI IP27 specific PCI rework and a batch of fixes: - A build fix for BMIPS5000 configurations with CONFIG_HW_PERF_EVENTS=y, which also neatly removes some #ifdefery. - A fix to report supported ISAs correctly on older Ingenic SoCs which incorrectly indicate MIPSr2 support in their cop0 Config register. - Some PCI modernization for SGI IP27 systems as part of ongoing work to support some other SGI systems. - A fix allowing use of appended DTB files with generic kernels. - DMA mask fixes for SGI IP22 & Alchemy systems" * tag 'mips_5.2_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: MIPS: Alchemy: add DMA masks for on-chip ethernet MIPS: SGI-IP22: provide missing dma_mask/coherent_dma_mask generic: fix appended dtb support MIPS: SGI-IP27: abstract chipset irq from bridge MIPS: SGI-IP27: use generic PCI driver MIPS: Fix Ingenic SoCs sometimes reporting wrong ISA MIPS: perf: Fix build with CONFIG_CPU_BMIPS5000 enabled
2019-05-19Merge tag 'riscv-for-linus-5.2-mw2' of ↵Linus Torvalds36-321/+635
git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux Pull RISC-V updates from Palmer Dabbelt: "This contains an assortment of RISC-V related patches that I'd like to target for the 5.2 merge window. Most of the patches are cleanups, but there are a handful of user-visible changes: - The nosmp and nr_cpus command-line arguments are now supported, which work like normal. - The SBI console no longer installs itself as a preferred console, we rely on standard mechanisms (/chosen, command-line, hueristics) instead. - sfence_remove_sfence_vma{,_asid} now pass their arguments along to the SBI call. - Modules now support BUG(). - A missing sfence.vma during boot has been added. This bug only manifests during boot. - The arch/riscv support for SiFive's L2 cache controller has been merged, which should un-block the EDAC framework work. I've only tested this on QEMU again, as I didn't have time to get things running on the Unleashed. The latest master from this morning merges in cleanly and passes the tests as well" * tag 'riscv-for-linus-5.2-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux: (31 commits) riscv: fix locking violation in page fault handler RISC-V: sifive_l2_cache: Add L2 cache controller driver for SiFive SoCs RISC-V: Add DT documentation for SiFive L2 Cache Controller RISC-V: Avoid using invalid intermediate translations riscv: Support BUG() in kernel module riscv: Add the support for c.ebreak check in is_valid_bugaddr() riscv: support trap-based WARN() riscv: fix sbi_remote_sfence_vma{,_asid}. riscv: move switch_mm to its own file riscv: move flush_icache_{all,mm} to cacheflush.c tty: Don't force RISCV SBI console as preferred console RISC-V: Access CSRs using CSR numbers RISC-V: Add interrupt related SCAUSE defines in asm/csr.h RISC-V: Use tabs to align macro values in asm/csr.h RISC-V: Fix minor checkpatch issues. RISC-V: Support nr_cpus command line option. RISC-V: Implement nosmp commandline option. RISC-V: Add RISC-V specific arch_match_cpu_phys_id riscv: vdso: drop unnecessary cc-ldoption riscv: call pm_power_off from machine_halt / machine_power_off ...
2019-05-18kselftests: netfilter: fix leftover net/net-next merge conflictFlorian Westphal1-51/+26
In nf-next, I had extended this script to also cover NAT support for the inet family. In nf, I extended it to cover a regression with 'fully-random' masquerade. Make this script work again by resolving the conflicts as needed. Fixes: 8b4483658364f0 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-19kconfig: use 'else ifneq' for Makefile to improve readabilityMasahiro Yamada1-3/+1
'ifeq ... else ifneq ... endif' notation is supported by GNU Make 3.81 or later, which is the requirement for building the kernel since commit 37d69ee30808 ("docs: bump minimal GNU Make version to 3.81"). Use it to improve the readability. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-05-18panic: add an option to replay all the printk message in bufferFeng Tang5-4/+24
Currently on panic, kernel will lower the loglevel and print out pending printk msg only with console_flush_on_panic(). Add an option for users to configure the "panic_print" to replay all dmesg in buffer, some of which they may have never seen due to the loglevel setting, which will help panic debugging . [feng.tang@intel.com: keep the original console_flush_on_panic() inside panic()] Link: http://lkml.kernel.org/r/1556199137-14163-1-git-send-email-feng.tang@intel.com [feng.tang@intel.com: use logbuf lock to protect the console log index] Link: http://lkml.kernel.org/r/1556269868-22654-1-git-send-email-feng.tang@intel.com Link: http://lkml.kernel.org/r/1556095872-36838-1-git-send-email-feng.tang@intel.com Signed-off-by: Feng Tang <feng.tang@intel.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Cc: Aaro Koskinen <aaro.koskinen@nokia.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: Kees Cook <keescook@chromium.org> Cc: Borislav Petkov <bp@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18initramfs: don't free a non-existent initrdSteven Price1-1/+1
Since commit 54c7a8916a88 ("initramfs: free initrd memory if opening /initrd.image fails"), the kernel has unconditionally attempted to free the initrd even if it doesn't exist. In the non-existent case this causes a boot-time splat if CONFIG_DEBUG_VIRTUAL is enabled due to a call to virt_to_phys() with a NULL address. Instead we should check that the initrd actually exists and only attempt to free it if it does. Link: http://lkml.kernel.org/r/20190516143125.48948-1-steven.price@arm.com Fixes: 54c7a8916a88 ("initramfs: free initrd memory if opening /initrd.image fails") Signed-off-by: Steven Price <steven.price@arm.com> Reported-by: Mark Rutland <mark.rutland@arm.com> Tested-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18fs/writeback.c: use rcu_barrier() to wait for inflight wb switches going ↵Jiufei Xue1-3/+8
into workqueue when umount synchronize_rcu() didn't wait for call_rcu() callbacks, so inode wb switch may not go to the workqueue after synchronize_rcu(). Thus previous scheduled switches was not finished even flushing the workqueue, which will cause a NULL pointer dereferenced followed below. VFS: Busy inodes after unmount of vdd. Self-destruct in 5 seconds. Have a nice day... BUG: unable to handle kernel NULL pointer dereference at 0000000000000278 evict+0xb3/0x180 iput+0x1b0/0x230 inode_switch_wbs_work_fn+0x3c0/0x6a0 worker_thread+0x4e/0x490 ? process_one_work+0x410/0x410 kthread+0xe6/0x100 ret_from_fork+0x39/0x50 Replace the synchronize_rcu() call with a rcu_barrier() to wait for all pending callbacks to finish. And inc isw_nr_in_flight after call_rcu() in inode_switch_wbs() to make more sense. Link: http://lkml.kernel.org/r/20190429024108.54150-1-jiufei.xue@linux.alibaba.com Signed-off-by: Jiufei Xue <jiufei.xue@linux.alibaba.com> Acked-by: Tejun Heo <tj@kernel.org> Suggested-by: Tejun Heo <tj@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18mm/compaction.c: correct zone boundary handling when isolating pages from a ↵Mel Gorman1-2/+2
pageblock syzbot reported the following error from a tree with a head commit of baf76f0c58ae ("slip: make slhc_free() silently accept an error pointer") BUG: unable to handle kernel paging request at ffffea0003348000 #PF error: [normal kernel read fault] PGD 12c3f9067 P4D 12c3f9067 PUD 12c3f8067 PMD 0 Oops: 0000 [#1] PREEMPT SMP KASAN CPU: 1 PID: 28916 Comm: syz-executor.2 Not tainted 5.1.0-rc6+ #89 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:constant_test_bit arch/x86/include/asm/bitops.h:314 [inline] RIP: 0010:PageCompound include/linux/page-flags.h:186 [inline] RIP: 0010:isolate_freepages_block+0x1c0/0xd40 mm/compaction.c:579 Code: 01 d8 ff 4d 85 ed 0f 84 ef 07 00 00 e8 29 00 d8 ff 4c 89 e0 83 85 38 ff ff ff 01 48 c1 e8 03 42 80 3c 38 00 0f 85 31 0a 00 00 <4d> 8b 2c 24 31 ff 49 c1 ed 10 41 83 e5 01 44 89 ee e8 3a 01 d8 ff RSP: 0018:ffff88802b31eab8 EFLAGS: 00010246 RAX: 1ffffd4000669000 RBX: 00000000000cd200 RCX: ffffc9000a235000 RDX: 000000000001ca5e RSI: ffffffff81988cc7 RDI: 0000000000000001 RBP: ffff88802b31ebd8 R08: ffff88805af700c0 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffffea0003348000 R13: 0000000000000000 R14: ffff88802b31f030 R15: dffffc0000000000 FS: 00007f61648dc700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffea0003348000 CR3: 0000000037c64000 CR4: 00000000001426e0 Call Trace: fast_isolate_around mm/compaction.c:1243 [inline] fast_isolate_freepages mm/compaction.c:1418 [inline] isolate_freepages mm/compaction.c:1438 [inline] compaction_alloc+0x1aee/0x22e0 mm/compaction.c:1550 There is no reproducer and it is difficult to hit -- 1 crash every few days. The issue is very similar to the fix in commit 6b0868c820ff ("mm/compaction.c: correct zone boundary handling when resetting pageblock skip hints"). When isolating free pages around a target pageblock, the boundary handling is off by one and can stray into the next pageblock. Triggering the syzbot error requires that the end of pageblock is section or zone aligned, and that the next section is unpopulated. A more subtle consequence of the bug is that pageblocks were being improperly used as migration targets which potentially hurts fragmentation avoidance in the long-term one page at a time. A debugging patch revealed that it's definitely possible to stray outside of a pageblock which is not intended. While syzbot cannot be used to verify this patch, it was confirmed that the debugging warning no longer triggers with this patch applied. It has also been confirmed that the THP allocation stress tests are not degraded by this patch. Link: http://lkml.kernel.org/r/20190510182124.GI18914@techsingularity.net Fixes: e332f741a8dd ("mm, compaction: be selective about what pageblocks to clear skip hints") Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Reported-by: syzbot+d84c80f9fe26a0f7a734@syzkaller.appspotmail.com Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Qian Cai <cai@lca.pw> Cc: Michal Hocko <mhocko@suse.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> # v5.1+ Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18mm/vmap: add DEBUG_AUGMENT_LOWEST_MATCH_CHECK macroUladzislau Rezki (Sony)1-0/+43
This macro adds some debug code to check that vmap allocations are happened in ascending order. By default this option is set to 0 and not active. It requires recompilation of the kernel to activate it. Set to 1, compile the kernel. [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-4-urezki@gmail.com Link: http://lkml.kernel.org/r/20190402162531.10888-4-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Joel Fernandes <joelaf@google.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18mm/vmap: add DEBUG_AUGMENT_PROPAGATE_CHECK macroUladzislau Rezki (Sony)1-0/+48
This macro adds some debug code to check that the augment tree is maintained correctly, meaning that every node contains valid subtree_max_size value. By default this option is set to 0 and not active. It requires recompilation of the kernel to activate it. Set to 1, compile the kernel. [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-3-urezki@gmail.com Link: http://lkml.kernel.org/r/20190402162531.10888-3-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Joel Fernandes <joelaf@google.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18mm/vmalloc.c: keep track of free blocks for vmap allocationUladzislau Rezki (Sony)2-247/+763
Patch series "improve vmap allocation", v3. Objective --------- Please have a look for the description at: https://lkml.org/lkml/2018/10/19/786 but let me also summarize it a bit here as well. The current implementation has O(N) complexity. Requests with different permissive parameters can lead to long allocation time. When i say "long" i mean milliseconds. Description ----------- This approach organizes the KVA memory layout into free areas of the 1-ULONG_MAX range, i.e. an allocation is done over free areas lookups, instead of finding a hole between two busy blocks. It allows to have lower number of objects which represent the free space, therefore to have less fragmented memory allocator. Because free blocks are always as large as possible. It uses the augment tree where all free areas are sorted in ascending order of va->va_start address in pair with linked list that provides O(1) access to prev/next elements. Since the tree is augment, we also maintain the "subtree_max_size" of VA that reflects a maximum available free block in its left or right sub-tree. Knowing that, we can easily traversal toward the lowest (left most path) free area. Allocation: ~O(log(N)) complexity. It is sequential allocation method therefore tends to maximize locality. The search is done until a first suitable block is large enough to encompass the requested parameters. Bigger areas are split. I copy paste here the description of how the area is split, since i described it in https://lkml.org/lkml/2018/10/19/786 <snip> A free block can be split by three different ways. Their names are FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they correspond to how requested size and alignment fit to a free block. FL_FIT_TYPE - in this case a free block is just removed from the free list/tree because it fully fits. Comparing with current design there is an extra work with rb-tree updating. LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do is just cutting a free block. It is as fast as a current design. Most of the vmalloc allocations just end up with this case, because the edge is always aligned to 1. NE_FIT_TYPE - Is much less common case. Basically it happens when requested size and alignment does not fit left nor right edges, i.e. it is between them. In this case during splitting we have to build a remaining left free area and place it back to the free list/tree. Comparing with current design there are two extra steps. First one is we have to allocate a new vmap_area structure. Second one we have to insert that remaining free block to the address sorted list/tree. In order to optimize a first case there is a cache with free_vmap objects. Instead of allocating from slab we just take an object from the cache and reuse it. Second one is pretty optimized. Since we know a start point in the tree we do not do a search from the top. Instead a traversal begins from a rb-tree node we split. <snip> De-allocation. ~O(log(N)) complexity. An area is not inserted straight away to the tree/list, instead we identify the spot first, checking if it can be merged around neighbors. The list provides O(1) access to prev/next, so it is pretty fast to check it. Summarizing. If merged then large coalesced areas are created, if not the area is just linked making more fragments. There is one more thing that i should mention here. After modification of VA node, its subtree_max_size is updated if it was/is the biggest area in its left or right sub-tree. Apart of that it can also be populated back to upper levels to fix the tree. For more details please have a look at the __augment_tree_propagate_from() function and the description. Tests and stressing ------------------- I use the "test_vmalloc.sh" test driver available under "tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo ./test_vmalloc.sh" to find out how to deal with it. Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA. Regarding last one, i do not have any physical access to NUMA system, therefore i emulated it. The time of stressing is days. If you run the test driver in "stress mode", you also need the patch that is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it: http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c After massive testing, i have not identified any problems like memory leaks, crashes or kernel panics. I find it stable, but more testing would be good. Performance analysis -------------------- I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1 as well, but the results have not been ready by time i an writing this. Currently it consist of 8 tests. There are three of them which correspond to different types of splitting(to compare with default). We have 3 ones(see above). Another 5 do allocations in different conditions. a) sudo ./test_vmalloc.sh performance When the test driver is run in "performance" mode, it runs all available tests pinned to first online CPU with sequential execution test order. We do it in order to get stable and repeatable results. Take a look at time difference in "long_busy_list_alloc_test". It is not surprising because the worst case is O(N). # i5-3320M How many cycles all tests took: CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt # Hikey960 8x CPUs How many cycles all tests took: CPU0=3478683207 cycles vs CPU0=463767978 cycles # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt b) time sudo ./test_vmalloc.sh test_repeat_count=1 With this configuration, all tests are run on all available online CPUs. Before running each CPU shuffles its tests execution order. It gives random allocation behaviour. So it is rough comparison, but it puts in the picture for sure. # i5-3320M <default> vs <patched> real 101m22.813s real 0m56.805s user 0m0.011s user 0m0.015s sys 0m5.076s sys 0m0.023s # See detailed table with results here: ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt # Hikey960 8x CPUs <default> vs <patched> real unknown real 4m25.214s user unknown user 0m0.011s sys unknown sys 0m0.670s I did not manage to complete this test on "default Hikey960" kernel version. After 24 hours it was still running, therefore i had to cancel it. That is why real/user/sys are "unknown". This patch (of 3): Currently an allocation of the new vmap area is done over busy list iteration(complexity O(n)) until a suitable hole is found between two busy areas. Therefore each new allocation causes the list being grown. Due to over fragmented list and different permissive parameters an allocation can take a long time. For example on embedded devices it is milliseconds. This patch organizes the KVA memory layout into free areas of the 1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks sorted by their offsets in pair with linked list keeping the free space in order of increasing addresses. Nodes are augmented with the size of the maximum available free block in its left or right sub-tree. Thus, that allows to take a decision and traversal toward the block that will fit and will have the lowest start address, i.e. it is sequential allocation. Allocation: to allocate a new block a search is done over the tree until a suitable lowest(left most) block is large enough to encompass: the requested size, alignment and vstart point. If the block is bigger than requested size - it is split. De-allocation: when a busy vmap area is freed it can either be merged or inserted to the tree. Red-black tree allows efficiently find a spot whereas a linked list provides a constant-time access to previous and next blocks to check if merging can be done. In case of merging of de-allocated memory chunk a large coalesced area is created. Complexity: ~O(log(N)) [urezki@gmail.com: v3] Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Joel Fernandes <joelaf@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-18Merge branch 'mlxsw-Two-port-module-fixes'David S. Miller5-2/+33
Ido Schimmel says: ==================== mlxsw: Two port module fixes Patch #1 fixes driver initialization failure on old ASICs due to unsupported register access. This is fixed by first testing if the register is supported. Patch #2 fixes reading of certain modules' EEPROM. The problem and solution are explained in detail in the commit message. Please consider both patches for stable. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-18mlxsw: core: Prevent reading unsupported slave address from SFP EEPROMVadim Pasternak1-2/+16
Prevent reading unsupported slave address from SFP EEPROM by testing Diagnostic Monitoring Type byte in EEPROM. Read only page zero of EEPROM, in case this byte is zero. If some SFP transceiver does not support Digital Optical Monitoring (DOM), reading SFP EEPROM slave address 0x51 could return an error. Availability of DOM support is verified by reading from zero page Diagnostic Monitoring Type byte describing how diagnostic monitoring is implemented by transceiver. If bit 6 of this byte is set, it indicates that digital diagnostic monitoring has been implemented. Otherwise it is not and transceiver could fail to reply to transaction for slave address 0x51 [1010001X (A2h)], which is used to access measurements page. Such issue has been observed when reading cable MCP2M00-xxxx, MCP7F00-xxxx, and few others. Fixes: 2ea109039cd3 ("mlxsw: spectrum: Add support for access cable info via ethtool") Fixes: 4400081b631a ("mlxsw: spectrum: Fix EEPROM access in case of SFP/SFP+") Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-18mlxsw: core: Prevent QSFP module initialization for old hardwareVadim Pasternak4-0/+17
Old Mellanox silicons, like switchx-2, switch-ib do not support reading QSFP modules temperature through MTMP register. Attempt to access this register on systems equipped with the this kind of silicon will cause initialization flow failure. Test for hardware resource capability is added in order to distinct between old and new silicon - old silicons do not have such capability. Fixes: 6a79507cfe94 ("mlxsw: core: Extend thermal module with per QSFP module thermal zones") Fixes: 5c42eaa07bd0 ("mlxsw: core: Extend hwmon interface with QSFP module temperature attributes") Reported-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-18vsock/virtio: Initialize core virtio vsock before registering the driverJorge E. Moreira1-7/+6
Avoid a race in which static variables in net/vmw_vsock/af_vsock.c are accessed (while handling interrupts) before they are initialized. [ 4.201410] BUG: unable to handle kernel paging request at ffffffffffffffe8 [ 4.207829] IP: vsock_addr_equals_addr+0x3/0x20 [ 4.211379] PGD 28210067 P4D 28210067 PUD 28212067 PMD 0 [ 4.211379] Oops: 0000 [#1] PREEMPT SMP PTI [ 4.211379] Modules linked in: [ 4.211379] CPU: 1 PID: 30 Comm: kworker/1:1 Not tainted 4.14.106-419297-gd7e28cc1f241 #1 [ 4.211379] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014 [ 4.211379] Workqueue: virtio_vsock virtio_transport_rx_work [ 4.211379] task: ffffa3273d175280 task.stack: ffffaea1800e8000 [ 4.211379] RIP: 0010:vsock_addr_equals_addr+0x3/0x20 [ 4.211379] RSP: 0000:ffffaea1800ebd28 EFLAGS: 00010286 [ 4.211379] RAX: 0000000000000002 RBX: 0000000000000000 RCX: ffffffffb94e42f0 [ 4.211379] RDX: 0000000000000400 RSI: ffffffffffffffe0 RDI: ffffaea1800ebdd0 [ 4.211379] RBP: ffffaea1800ebd58 R08: 0000000000000001 R09: 0000000000000001 [ 4.211379] R10: 0000000000000000 R11: ffffffffb89d5d60 R12: ffffaea1800ebdd0 [ 4.211379] R13: 00000000828cbfbf R14: 0000000000000000 R15: ffffaea1800ebdc0 [ 4.211379] FS: 0000000000000000(0000) GS:ffffa3273fd00000(0000) knlGS:0000000000000000 [ 4.211379] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 4.211379] CR2: ffffffffffffffe8 CR3: 000000002820e001 CR4: 00000000001606e0 [ 4.211379] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 4.211379] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 4.211379] Call Trace: [ 4.211379] ? vsock_find_connected_socket+0x6c/0xe0 [ 4.211379] virtio_transport_recv_pkt+0x15f/0x740 [ 4.211379] ? detach_buf+0x1b5/0x210 [ 4.211379] virtio_transport_rx_work+0xb7/0x140 [ 4.211379] process_one_work+0x1ef/0x480 [ 4.211379] worker_thread+0x312/0x460 [ 4.211379] kthread+0x132/0x140 [ 4.211379] ? process_one_work+0x480/0x480 [ 4.211379] ? kthread_destroy_worker+0xd0/0xd0 [ 4.211379] ret_from_fork+0x35/0x40 [ 4.211379] Code: c7 47 08 00 00 00 00 66 c7 07 28 00 c7 47 08 ff ff ff ff c7 47 04 ff ff ff ff c3 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 8b 47 08 <3b> 46 08 75 0a 8b 47 04 3b 46 04 0f 94 c0 c3 31 c0 c3 90 66 2e [ 4.211379] RIP: vsock_addr_equals_addr+0x3/0x20 RSP: ffffaea1800ebd28 [ 4.211379] CR2: ffffffffffffffe8 [ 4.211379] ---[ end trace f31cc4a2e6df3689 ]--- [ 4.211379] Kernel panic - not syncing: Fatal exception in interrupt [ 4.211379] Kernel Offset: 0x37000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff) [ 4.211379] Rebooting in 5 seconds.. Fixes: 22b5c0b63f32 ("vsock/virtio: fix kernel panic after device hot-unplug") Cc: Stefan Hajnoczi <stefanha@redhat.com> Cc: Stefano Garzarella <sgarzare@redhat.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: kvm@vger.kernel.org Cc: virtualization@lists.linux-foundation.org Cc: netdev@vger.kernel.org Cc: kernel-team@android.com Cc: stable@vger.kernel.org [4.9+] Signed-off-by: Jorge E. Moreira <jemoreira@google.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Acked-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-18Merge tag 'perf-core-for-mingo-5.2-20190517' of ↵Ingo Molnar94-214/+5414
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo: perf.data: Alexey Budankov: - Streaming compression of perf ring buffer into PERF_RECORD_COMPRESSED user space records, resulting in ~3-5x perf.data file size reduction on variety of tested workloads what saves storage space on larger server systems where perf.data size can easily reach several tens or even hundreds of GiBs, especially when profiling with DWARF-based stacks and tracing of context switches. perf record: Arnaldo Carvalho de Melo - Improve -user-regs/intr-regs suggestions to overcome errors. perf annotate: Jin Yao: - Remove hist__account_cycles() from callback, speeding up branch processing (perf record -b). perf stat: - Add a 'percore' event qualifier, e.g.: -e cpu/event=0,umask=0x3,percore=1/, that sums up the event counts for both hardware threads in a core. We can already do this with --per-core, but it's often useful to do this together with other metrics that are collected per hardware thread. I.e. now its possible to do this per-event, and have it mixed with other events not aggregated by core. core libraries: Donald Yandt: - Check for errors when doing fgets(/proc/version). Jiri Olsa: - Speed up report for perf compiled with linbunwind. tools headers: Arnaldo Carvalho de Melo - Update memcpy_64.S, x86's kvm.h and pt_regs.h. arm64: Florian Fainelli: - Map Brahma-B53 CPUID to cortex-a53 events. - Add Cortex-A57 and Cortex-A72 events. csky: Mao Han: - Add DWARF register mappings for libdw, allowing --call-graph=dwarf to work on the C-SKY arch. x86: Andi Kleen/Kan Liang: - Add support for recording and printing XMM registers, available, for instance, on Icelake. Kan Liang: - Add uncore_upi (Intel's "Ultra Path Interconnect" events) JSON support. UPI replaced the Intel QuickPath Interconnect (QPI) in Xeon Skylake-SP. Intel PT: Adrian Hunter . Fix instructions sampling rate. . Timestamp fixes. . Improve exported-sql-viewer GUI, allowing, for instance, to copy'n'paste the trees, useful for e-mailing. Documentation: Thomas Richter: - Add description for 'perf --debug stderr=1', which redirects stderr to stdout. libtraceevent: Tzvetomir Stoyanov: - Add man pages for the various APIs. Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-05-18kbuild: check uniqueness of module namesMasahiro Yamada2-0/+17
In the recent build test of linux-next, Stephen saw a build error caused by a broken .tmp_versions/*.mod file: https://lkml.org/lkml/2019/5/13/991 drivers/net/phy/asix.ko and drivers/net/usb/asix.ko have the same basename, and there is a race in generating .tmp_versions/asix.mod Kbuild has not checked this before, and it suddenly shows up with obscure error messages when this kind of race occurs. Non-unique module names cause various sort of problems, but it is not trivial to catch them by eyes. Hence, this script. It checks not only real modules, but also built-in modules (i.e. controlled by tristate CONFIG option, but currently compiled with =y). Non-unique names for built-in modules also cause problems because /sys/modules/ would fall over. For the latest kernel, I tested "make allmodconfig all" (or more quickly "make allyesconfig modules"), and it detected the following: warning: same basename if the following are built as modules: drivers/regulator/88pm800.ko drivers/mfd/88pm800.ko warning: same basename if the following are built as modules: drivers/gpu/drm/bridge/adv7511/adv7511.ko drivers/media/i2c/adv7511.ko warning: same basename if the following are built as modules: drivers/net/phy/asix.ko drivers/net/usb/asix.ko warning: same basename if the following are built as modules: fs/coda/coda.ko drivers/media/platform/coda/coda.ko warning: same basename if the following are built as modules: drivers/net/phy/realtek.ko drivers/net/dsa/realtek.ko Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
2019-05-18kconfig: Terminate menu blocks with a comment in the generated configAlexander Popov1-1/+12
Currently menu blocks start with a pretty header but end with nothing in the generated config. So next config options stick together with the options from the menu block. Let's terminate menu blocks in the generated config with a comment and a newline if needed. Example: ... CONFIG_BPF_STREAM_PARSER=y CONFIG_NET_FLOW_LIMIT=y # # Network testing # CONFIG_NET_PKTGEN=y CONFIG_NET_DROP_MONITOR=y # end of Network testing # end of Networking options CONFIG_HAMRADIO=y ... Signed-off-by: Alexander Popov <alex.popov@linux.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-05-18kbuild: add LICENSES to KBUILD_ALLDIRSMasahiro Yamada1-1/+1
For *-pkg targets, the LICENSES directory should be included in the source tarball. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-05-18kbuild: remove 'addtree' and 'flags' magic for header search pathsMasahiro Yamada3-33/+13
The 'addtree' and 'flags' in scripts/Kbuild.include are so compilecated and ugly. As I mentioned in [1], Kbuild should stop automatic prefixing of header search path options. I fixed up (almost) all Makefiles in the kernel. Now 'addtree' and 'flags' have been removed. Kbuild still caters to add $(srctree)/$(src) and $(objtree)/$(obj) to the header search path for O= building, but never touches extra compiler options from ccflags-y etc. [1]: https://patchwork.kernel.org/patch/9632347/ Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-05-18treewide: prefix header search paths with $(srctree)/Masahiro Yamada17-26/+25
Currently, the Kbuild core manipulates header search paths in a crazy way [1]. To fix this mess, I want all Makefiles to add explicit $(srctree)/ to the search paths in the srctree. Some Makefiles are already written in that way, but not all. The goal of this work is to make the notation consistent, and finally get rid of the gross hacks. Having whitespaces after -I does not matter since commit 48f6e3cf5bc6 ("kbuild: do not drop -I without parameter"). [1]: https://patchwork.kernel.org/patch/9632347/ Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-05-18media: prefix header search paths with $(srctree)/Masahiro Yamada30-49/+47
Currently, the Kbuild core manipulates header search paths in a crazy way [1]. To fix this mess, I want all Makefiles to add explicit $(srctree)/ to the search paths in the srctree. Some Makefiles are already written in that way, but not all. The goal of this work is to make the notation consistent, and finally get rid of the gross hacks. Having whitespaces after -I does not matter since commit 48f6e3cf5bc6 ("kbuild: do not drop -I without parameter"). [1]: https://patchwork.kernel.org/patch/9632347/ Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
2019-05-18media: remove unneeded header search pathsMasahiro Yamada7-11/+0
I was able to build without these extra header search paths. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-05-18alpha: move arch/alpha/defconfig to arch/alpha/configs/defconfigMasahiro Yamada2-0/+2
As of Linux 5.1, alpha and s390 are the last architectures that have defconfig in arch/*/ instead of arch/*/configs/. $ find arch -name defconfig | sort arch/alpha/defconfig arch/arm64/configs/defconfig arch/csky/configs/defconfig arch/nds32/configs/defconfig arch/riscv/configs/defconfig arch/s390/defconfig The arch/$(ARCH)/defconfig is the hard-coded default in Kconfig, and I want to deprecate it after evacuating the remaining defconfig into the standard location, arch/*/configs/. Define KBUILD_DEFCONFIG like other architectures, and move defconfig into the configs/ subdirectory. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Paul Walmsley <paul@pwsan.com>
2019-05-18kbuild: terminate Kconfig when $(CC) or $(LD) is missingMasahiro Yamada2-1/+9
If the compiler specified by $(CC) is not present, the Kconfig stage sprinkles 'not found' messages, then succeeds. $ make CROSS_COMPILE=foo defconfig /bin/sh: 1: foogcc: not found /bin/sh: 1: foogcc: not found *** Default configuration is based on 'x86_64_defconfig' ./scripts/gcc-version.sh: 17: ./scripts/gcc-version.sh: foogcc: not found ./scripts/gcc-version.sh: 18: ./scripts/gcc-version.sh: foogcc: not found ./scripts/gcc-version.sh: 19: ./scripts/gcc-version.sh: foogcc: not found ./scripts/gcc-version.sh: 17: ./scripts/gcc-version.sh: foogcc: not found ./scripts/gcc-version.sh: 18: ./scripts/gcc-version.sh: foogcc: not found ./scripts/gcc-version.sh: 19: ./scripts/gcc-version.sh: foogcc: not found ./scripts/clang-version.sh: 11: ./scripts/clang-version.sh: foogcc: not found ./scripts/gcc-plugin.sh: 11: ./scripts/gcc-plugin.sh: foogcc: not found init/Kconfig:16:warning: 'GCC_VERSION': number is invalid # # configuration written to .config # Terminate parsing files immediately if $(CC) or $(LD) is not found. "make *config" will fail more nicely. $ make CROSS_COMPILE=foo defconfig *** Default configuration is based on 'x86_64_defconfig' scripts/Kconfig.include:34: compiler 'foogcc' not found make[1]: *** [scripts/kconfig/Makefile;82: defconfig] Error 1 make: *** [Makefile;557: defconfig] Error 2 Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-05-18kbuild: turn auto.conf.cmd into a mandatory include fileMasahiro Yamada1-1/+1
syncconfig is responsible for keeping auto.conf up-to-date, so if it fails for any reason, the build must be terminated immediately. However, since commit 9390dff66a52 ("kbuild: invoke syncconfig if include/config/auto.conf.cmd is missing"), Kbuild continues running even after syncconfig fails. You can confirm this by intentionally making syncconfig error out: diff --git a/scripts/kconfig/confdata.c b/scripts/kconfig/confdata.c index 08ba146..307b9de 100644 --- a/scripts/kconfig/confdata.c +++ b/scripts/kconfig/confdata.c @@ -1023,6 +1023,9 @@ int conf_write_autoconf(int overwrite) FILE *out, *tristate, *out_h; int i; + if (overwrite) + return 1; + if (!overwrite && is_present(autoconf_name)) return 0; Then, syncconfig fails, but Make would not stop: $ make -s mrproper allyesconfig defconfig $ make scripts/kconfig/conf --syncconfig Kconfig *** Error during sync of the configuration. make[2]: *** [scripts/kconfig/Makefile;69: syncconfig] Error 1 make[1]: *** [Makefile;557: syncconfig] Error 2 make: *** [include/config/auto.conf.cmd] Deleting file 'include/config/tristate.conf' make: Failed to remake makefile 'include/config/auto.conf'. SYSTBL arch/x86/include/generated/asm/syscalls_32.h SYSHDR arch/x86/include/generated/asm/unistd_32_ia32.h SYSHDR arch/x86/include/generated/asm/unistd_64_x32.h SYSTBL arch/x86/include/generated/asm/syscalls_64.h [ continue running ... ] The reason is in the behavior of a pattern rule with multi-targets. %/auto.conf %/auto.conf.cmd %/tristate.conf: $(KCONFIG_CONFIG) $(Q)$(MAKE) -f $(srctree)/Makefile syncconfig GNU Make knows this rule is responsible for making all the three files simultaneously. As far as examined, auto.conf.cmd is the target in question when this rule is invoked. It is probably because auto.conf.cmd is included below the inclusion of auto.conf. The inclusion of auto.conf is mandatory, while that of auto.conf.cmd is optional. GNU Make does not care about the failure in the process of updating optional include files. I filed this issue (https://savannah.gnu.org/bugs/?56301) in case this behavior could be improved somehow in future releases of GNU Make. Anyway, it is quite easy to fix our Makefile. Given that auto.conf is already a mandatory include file, there is no reason to stick auto.conf.cmd optional. Make it mandatory as well. Cc: linux-stable <stable@vger.kernel.org> # 5.0+ Fixes: 9390dff66a52 ("kbuild: invoke syncconfig if include/config/auto.conf.cmd is missing") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-05-18.gitignore: exclude .get_maintainer.ignore and .gitattributesMasahiro Yamada1-3/+5
Also, sort the patterns alphabetically. Update the comment since we have non-git files here. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-05 20:38:20 +0000