| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The USB Embedded High-speed Host Electrical Test (EHSET) defines the
SINGLE_STEP_SET_FEATURE test as follows:
1) The host enumerates the test device with VID:0x1A0A, PID:0x0108
2) The host sends the SETUP stage of a GetDescriptor(Device)
3) The device ACKs the request
4) The host issues SOFs for 15 seconds allowing the test operator to
raise the scope trigger just above the SOF voltage level
5) The host sends the IN packet
6) The device sends data in response, triggering the scope
7) The host sends an ACK in response to the data
This patch adds additional handling to the EHCI hub driver and allows
the EHSET driver to initiate this test mode by issuing a a SetFeature
request to the root hub with a Test Selector value of 0x06. From there
it mimics ehci_urb_enqueue() but separately submits QTDs for the
SETUP and DATA/STATUS stages in order to insert a delay in between.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[jackp@codeaurora.org: imported from commit c2084930 on codeaurora.org;
minor cleanup and updated author email]
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If someone provided meaningful error codes from reset() we should tell the
user what they were.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Correct use of devnum in supports_autosuspend documentation, the sysfs path
contains busnum-port.port.port not busnum-devnum (which is the usb bus device
address).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The config descriptors as read from /proc/bus/usb/BBB/DDD are in *bus* endian
format. Correct proc_usb_info.txt to correctly reflect that.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While reading the config parsing code I noticed this check is missing, without
this check config->desc.wTotalLength can end up with a value larger then the
dev->rawdescriptors length for the config, and when userspace then tries to
get the rawdescriptors bad things may happen.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Refactor so that register writes for configuration are only performed if
the device has a regmap provided and also register as a platform driver.
This allows the driver to be used to manage GPIO based control of the
device.
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The binding document says that all properties are required but in fact
almost all are optional (and should be) - update the document to reflect
this.
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are no software visible differences that I am aware of but in case
any are discovered allow the DTS to specify exactly which device is
present.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since there is no runtime interface for changing modes this is probably
the most sensible default.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In preparation for supporting operation without an I2C control interface
factor out the I2C-specific parts of the probe routine from those that
don't do any register I/O.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This will give access to the diagnostic infrastructure regmap has but
the main point is to support future refactoring.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the connect signal is pulled high then the device will start up meaning
that if we just pull it high on probe then the device will start running
prior to the configuration being written out. Fix this by pulling the GPIO
low when we reset and only pulling it high when configuration is finished.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The /RESET GPIO is not manipulated from atomic context so support GPIOs
that can't be written from atomic context by using _cansleep().
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When CONFIG_USB_SUPPORT is not selected we get things like:
scripts/kconfig/mconf Kconfig
warning: (MIPS_SEAD3 && PMC_MSP && CPU_CAVIUM_OCTEON) selects USB_EHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
It is much cleaner to make the various system Kconfigs select
USB_EHCI_BIG_ENDIAN_MMIO rather than move the system config
information into USB's Kconfig, but the warnings are annoying.
Eliminate the warning by moving the definition of
USB_EHCI_BIG_ENDIAN_MMIO outside of all the Kconfig if statements.
While we are at it move USB_OHCI_BIG_ENDIAN_DESC,
USB_OHCI_BIG_ENDIAN_MMIO, USB_OHCI_LITTLE_ENDIAN and
USB_EHCI_BIG_ENDIAN_DESC too, as they could very well suffer similar
problems for other systems.
Get rid of the redundant "default n" in USB_OHCI_BIG_ENDIAN_DESC and
USB_OHCI_BIG_ENDIAN_MMIO
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Saves us a bit of code.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The intn and connect GPIO properties are swapped in the code which will
cause failures at runtime if these are connected, fix the code.
There are currently no in-tree users of this device to check or update.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of having to create a new driver for a "simple" usb to serial
device, mush them all into one file, with a macro, so as to make it easy
to add new ones.
Cc: "René Bürgel" <rene.buergel@sohard.de>
Acked-by: Wei Shuai <cpuwolf@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Acked-by: Frans Klaver <frans.klaver@xsens.com>
Cc: "Wesley W. Terpstra" <w.terpstra@gsi.de>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch enables 'can_dma_sg' flag for ax88179_178a device
if the attached host controller supports building packet from
discontinuous buffers(DMA SG is possible), so TSO can be enabled
and skb fragment buffers can be passed to usb stack via urb->sg
directly.
With the patch, system CPU utilization decreased ~50% and throughput
increased by ~10% when doing iperf client test on one ARM A15 dual
core board.
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Grant Grundler <grundler@google.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Eric Dumazet <edumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch introduces support of DMA SG if the USB host controller
which usbnet device is attached to is capable of building packet from
discontinuous buffers.
The patch supports passing the skb fragment buffers to usb stack directly
via urb->sg.
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Grant Grundler <grundler@google.com>
Cc: Freddy Xin <freddy@asix.com.tw>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch marks all xHCI controllers as no_sg_constraint
since xHCI supports building packet from discontinuous buffers.
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some host controllers(such as xHCI) can support building
packet from discontinuous buffers, so introduce one flag
and helper for this kind of host controllers, then the
feature can help some applications(such as usbnet) by
supporting arbitrary length of sg buffers.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All 4 transfer types can work well on EHCI HCD after switching to run
URB giveback in tasklet context, so mark all HCD drivers to support
it.
Also we don't need to release ehci->lock during URB giveback any more.
>From below test results on 3 machines(2 ARM and one x86), time
consumed by EHCI interrupt handler droped much without performance
loss.
1 test description
1.1 mass storage performance test:
- run below command 10 times and compute the average performance
dd if=/dev/sdN iflag=direct of=/dev/null bs=200M count=1
- two usb mass storage device:
A: sandisk extreme USB 3.0 16G(used in test case 1 & case 2)
B: kingston DataTraveler G2 4GB(only used in test case 2)
1.2 uvc function test:
- run one simple capture program in the below link
http://kernel.ubuntu.com/~ming/up/capture.c
- capture format 640*480 and results in High Bandwidth mode on the
uvc device: Z-Star 0x0ac8/0x3450
- on T410(x86) laptop, also use guvcview to watch video capture/playback
1.3 about test2 and test4
- both two devices involved are tested concurrently by above test items
1.4 how to compute irq time(the time consumed by ehci_irq)
- use trace points of irq:irq_handler_entry and irq:irq_handler_exit
1.5 kernel
3.10.0-rc3-next-20130528
1.6 test machines
Pandaboard A1: ARM CortexA9 dural core
Arndale board: ARM CortexA15 dural core
T410: i5 CPU 2.67GHz quad core
2 test result
2.1 test case1: single mass storage device performance test
--------------------------------------------------------------------
upstream | patched
perf(MB/s)+irq time(us) | perf(MB/s)+irq time(us)
--------------------------------------------------------------------
Pandaboard A1: 25.280(avg:145,max:772) | 25.540(avg:14, max:75)
Arndale board: 29.700(avg:33, max:129) | 29.700(avg:10, max:50)
T410: 34.430(avg:17, max:154*)| 34.660(avg:12, max:155)
---------------------------------------------------------------------
2.2 test case2: two mass storage devices' performance test
--------------------------------------------------------------------
upstream | patched
perf(MB/s)+irq time(us) | perf(MB/s)+irq time(us)
--------------------------------------------------------------------
Pandaboard A1: 15.840/15.580(avg:158,max:1216) | 16.500/16.160(avg:15,max:139)
Arndale board: 17.370/16.220(avg:33 max:234) | 17.480/16.200(avg:11, max:91)
T410: 21.180/19.820(avg:18 max:160) | 21.220/19.880(avg:11, max:149)
---------------------------------------------------------------------
2.3 test case3: one uvc streaming test
- uvc device works well(on x86, luvcview can be used too and has
same result with uvc capture)
--------------------------------------------------------------------
upstream | patched
irq time(us) | irq time(us)
--------------------------------------------------------------------
Pandaboard A1: (avg:445, max:873) | (avg:33, max:44)
Arndale board: (avg:316, max:630) | (avg:20, max:27)
T410: (avg:39, max:107) | (avg:10, max:65)
---------------------------------------------------------------------
2.4 test case4: one uvc streaming plus one mass storage device test
--------------------------------------------------------------------
upstream | patched
perf(MB/s)+irq time(us) | perf(MB/s)+irq time(us)
--------------------------------------------------------------------
Pandaboard A1: 20.340(avg:259,max:1704)| 20.390(avg:24, max:101)
Arndale board: 23.460(avg:124,max:726) | 23.370(avg:15, max:52)
T410: 28.520(avg:27, max:169) | 28.630(avg:13, max:160)
---------------------------------------------------------------------
2.5 test case5: read single mass storage device with small transfer
- run below command 10 times and compute the average speed
dd if=/dev/sdN iflag=direct of=/dev/null bs=4K count=4000
1), test device A:
--------------------------------------------------------------------
upstream | patched
perf(MB/s)+irq time(us) | perf(MB/s)+irq time(us)
--------------------------------------------------------------------
Pandaboard A1: 6.5(avg:21, max:64) | 6.5(avg:10, max:24)
Arndale board: 8.13(avg:12, max:23) | 8.06(avg:7, max:17)
T410: 6.66(avg:13, max:131) | 6.84(avg:11, max:149)
---------------------------------------------------------------------
2), test device B:
--------------------------------------------------------------------
upstream | patched
perf(MB/s)+irq time(us) | perf(MB/s)+irq time(us)
--------------------------------------------------------------------
Pandaboard A1: 5.5(avg:21,max:43) | 5.49(avg:10, max:24)
Arndale board: 5.9(avg:12, max:22) | 5.9(avg:7, max:17)
T410: 5.48(avg:13, max:155) | 5.48(avg:7, max:140)
---------------------------------------------------------------------
* On T410, sometimes read ehci status register in ehci_irq takes more
than 100us, and the problem has been reported on the link:
http://marc.info/?t=137065867300001&r=1&w=2
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ehci-hcd currently unlinks an interrupt QH when it becomes empty, that
is, after its last URB completes. This works well because in almost
all cases, the completion handler for an interrupt URB resubmits the
URB; therefore the QH doesn't become empty and doesn't get unlinked.
When we start using tasklets for URB completion, this scheme won't work
as well. The resubmission won't occur until the tasklet runs, which
will be some time after the completion is queued with the tasklet.
During that delay, the QH will be empty and so will be unlinked
unnecessarily.
To prevent this problem, this patch adds a 5-ms time delay before empty
interrupt QHs are unlinked. Most often, during that time the interrupt
URB will be resubmitted and thus we can avoid unlinking the QH.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The patch does the below improvement:
- think QH_STATE_COMPLETING as unlinking state since all URBs on the
endpoint should be in unlinking or unlinked when doing endpoint_disable()
- add "WARN_ON(!list_empty(&qh->qtd_list));" if qh->qh_state is
QH_STATE_LINKED because there shouldn't be any active transfer in qh
- when qh->qh_state is QH_STATE_LINKED, the QH(async or periodic)
should be in its corresponding list, so the search through the async
list isn't necessary.
- unlink periodic QH to speed up unlinking if the QH is in linked
state
Basically, only the last one is related with this patchset because
the assumption of "periodic qh self-unlinks on empty" isn't true
any more when we introduce unlink-wait for periodic qh.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no good reason to run complete() in hard interrupt
disabled context.
After switch to run complete() in tasklet, we will enable local IRQs
when calling complete() since we can do it at that time.
Even though we still disable IRQs now when calling complete()
in tasklet, the URB documentation is updated to claim complete()
will be run in tasklet context and local IRQs will be enabled, so
that USB drivers can know the change and avoid one deadlock caused
by: assume IRQs disabled in complete() and call spin_lock() to
hold lock which might be acquired in interrupt context.
Current spin_lock() usages in drivers' complete() will be cleaned
up at the same time, and once the cleanup is finished, local IRQs
will be enabled when calling complete() in tasklet.
Also fix description about type of usb_complete_t, and remove the
advice of running completion handler in tasklet for decreasing
system latency.
Cc: Oliver Neukum <oliver@neukum.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch implements the mechanism of giveback of URB in
tasklet context, so that hardware interrupt handling time for
usb host controller can be saved much, and HCD interrupt handling
can be simplified.
Motivations:
1), on some arch(such as ARM), DMA mapping/unmapping is a bit
time-consuming, for example: when accessing usb mass storage
via EHCI on pandaboard, the common length of transfer buffer is 120KB,
the time consumed on DMA unmapping may reach hundreds of microseconds;
even on A15 based box, the time is still about scores of microseconds
2), on some arch, reading DMA coherent memoery is very time-consuming,
the most common example is usb video class driver[1]
3), driver's complete() callback may do much things which is driver
specific, so the time is consumed unnecessarily in hardware irq context.
4), running driver's complete() callback in hardware irq context causes
that host controller driver has to release its lock in interrupt handler,
so reacquiring the lock after return may busy wait a while and increase
interrupt handling time. More seriously, releasing the HCD lock makes
HCD becoming quite complicated to deal with introduced races.
So the patch proposes to run giveback of URB in tasklet context, then
time consumed in HCD irq handling doesn't depend on drivers' complete and
DMA mapping/unmapping any more, also we can simplify HCD since the HCD
lock isn't needed to be released during irq handling.
The patch should be reasonable and doable:
1), for drivers, they don't care if the complete() is called in hard irq
context or softirq context
2), the biggest change is the situation in which usb_submit_urb() is called
in complete() callback, so the introduced tasklet schedule delay might be a
con, but it shouldn't be a big deal:
- control/bulk asynchronous transfer isn't sensitive to schedule
delay
- the patch schedules giveback of periodic URBs using
tasklet_hi_schedule, so the introduced delay should be very
small
- for ISOC transfer, generally, drivers submit several URBs
concurrently to avoid interrupt delay, so it is OK with the
little schedule delay.
- for interrupt transfer, generally, drivers only submit one URB
at the same time, but interrupt transfer is often used in event
report, polling, ... situations, and a little delay should be OK.
Considered that HCDs may optimize on submitting URB in complete(), the
patch may cause the optimization not working, so introduces one flag to mark
if the HCD supports to run giveback URB in tasklet context. When all HCDs
are ready, the flag can be removed.
[1], http://marc.info/?t=136438111600010&r=1&w=2
Cc: Oliver Neukum <oliver@neukum.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want those fixes in here also.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
Pull dmaengine fixes from Vinod Koul:
"Two fixes for slave dmaengine. The first fixes cyclic dma transfers
for pl330 and the second one makes us return the correct error code on
probe"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: pl330: Fix cyclic transfers
pch_dma: fix error return code in pch_dma_probe()
|
|
Pull drm fix from Dave Airlie:
"Just a quick fix that a few people have reported, be nice to have in
asap"
The drm tree seems to be very confused about 64-bit divides. Here it
uses a slow 64-by-64 bit divide to divide by a small constant. Oh well.
Doesn't look performance-critical, just stupid.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: fix 64 bit divide in SI spm code
|
|
Commit 46a1c2c7ae53 ("vfs: export lseek_execute() to modules") broke the
tmpfs SEEK_DATA/SEEK_HOLE implementation, because vfs_setpos() converts
the carefully prepared -ENXIO to -EINVAL. Other filesystems avoid it in
error cases: do the same in tmpfs.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Jie Liu <jeff.liu@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All small regression or small fixes, nothing surprising at this stage.
- regression fix for intel Mac Mini quirk
- compress ioctl error fix
- ASoC fixes for control change notifications, some UI fixes,
driver-specific fixes (resource leak, build errors, etc)"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix missing fixup for Mac Mini with STAC9221
ASoC: wm0010: Fix resource leak
ASoC: au1x: Fix build
ASoC: bf5xx-ac97: Fix compile error with SND_BF5XX_HAVE_COLD_RESET
ASoC: bfin-ac97: Fix prototype error following AC'97 refactoring
ALSA: compress: fix the return value for SNDRV_COMPRESS_VERSION
ASoC: dapm: Fix return value of snd_soc_dapm_put_{volsw,enum_virt}()
|
|
Forgot to use the appropriate math64 function.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
|
|
Pull networking fixes from David Miller:
1) Don't ignore user initiated wireless regulatory settings on cards
with custom regulatory domains, from Arik Nemtsov.
2) Fix length check of bluetooth information responses, from Jaganath
Kanakkassery.
3) Fix misuse of PTR_ERR in btusb, from Adam Lee.
4) Handle rfkill properly while iwlwifi devices are offline, from
Emmanuel Grumbach.
5) Fix r815x devices DMA'ing to stack buffers, from Hayes Wang.
6) Kernel info leak in ATM packet scheduler, from Dan Carpenter.
7) 8139cp doesn't check for DMA mapping errors, from Neil Horman.
8) Fix bridge multicast code to not snoop when no querier exists,
otherwise mutlicast traffic is lost. From Linus Lüssing.
9) Avoid soft lockups in fib6_run_gc(), from Michal Kubecek.
10) Fix races in automatic address asignment on ipv6, which can result
in incorrect lifetime assignments. From Jiri Benc.
11) Cure build bustage when CONFIG_NET_LL_RX_POLL is not set and rename
it CONFIG_NET_RX_BUSY_POLL to eliminate the last reference to the
original naming of this feature. From Cong Wang.
12) Fix crash in TIPC when server socket creation fails, from Ying Xue.
13) macvlan_changelink() silently succeeds when it shouldn't, from
Michael S Tsirkin.
14) HTB packet scheduler can crash due to sign extension, fix from
Stephen Hemminger.
15) With the cable unplugged, r8169 prints out a message every 10
seconds, make it netif_dbg() instead of netif_warn(). From Peter
Wu.
16) Fix memory leak in rtm_to_ifaddr(), from Daniel Borkmann.
17) sis900 gets spurious TX queue timeouts due to mismanagement of link
carrier state, from Denis Kirjanov.
18) Validate somaxconn sysctl to make sure it fits inside of a u16.
From Roman Gushchin.
19) Fix MAC address filtering on qlcnic, from Shahed Shaikh.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (68 commits)
qlcnic: Fix for flash update failure on 83xx adapter
qlcnic: Fix link speed and duplex display for 83xx adapter
qlcnic: Fix link speed display for 82xx adapter
qlcnic: Fix external loopback test.
qlcnic: Removed adapter series name from warning messages.
qlcnic: Free up memory in error path.
qlcnic: Fix ingress MAC learning
qlcnic: Fix MAC address filter issue on 82xx adapter
net: ethernet: davinci_emac: drop IRQF_DISABLED
netlabel: use domain based selectors when address based selectors are not available
net: check net.core.somaxconn sysctl values
sis900: Fix the tx queue timeout issue
net: rtm_to_ifaddr: free ifa if ifa_cacheinfo processing fails
r8169: remove "PHY reset until link up" log spam
net: ethernet: cpsw: drop IRQF_DISABLED
htb: fix sign extension bug
macvlan: handle set_promiscuity failures
macvlan: better mode validation
tipc: fix oops when creating server socket fails
net: rename CONFIG_NET_LL_RX_POLL to CONFIG_NET_RX_BUSY_POLL
...
|
|
Flash update routine was improperly checking register read API return value.
Modify register read API and perform proper error check.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Set link speed and duplex to unknown when link is not up.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Do not obtain link speed from register when adapter
link is down.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver was not handling external loopback diagnostic
test request.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Delete MAC address from the adapter's filter table
if the source MAC address of ingress packet matches.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver was passing the address of a pointer instead of
the pointer itself.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IRQF_DISABLED is a no-op by now and should be removed.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull nfsd bugfixes from Bruce Fields:
"Most of this is due to a screwup on my part -- some gss-proxy crashes
got fixed before the merge window but somehow never made it out of a
temporary git repo on my laptop...."
* 'for-3.11' of git://linux-nfs.org/~bfields/linux:
svcrpc: set cr_gss_mech from gss-proxy as well as legacy upcall
svcrpc: fix kfree oops in gss-proxy code
svcrpc: fix gss-proxy xdr decoding oops
svcrpc: fix gss_rpc_upcall create error
NFSD/sunrpc: avoid deadlock on TCP connection due to memory pressure.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix chip initialization/configuration in MAX6697 driver"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (max6697) fix MAX6581 ideality
|
|
Pull arm fixes fixes from Russell King:
"This fixes a couple of problems with commit 48be69a026b2 ("ARM: move
signal handlers into a vdso-like page"), one of which was originally
discovered via my testing originally, but the fix for it was never
actually committed.
The other shows up on noMMU builds, and such platforms are extremely
rare and as such are not part of my nightly testing"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: fix nommu builds with 48be69a02 (ARM: move signal handlers into a vdso-like page)
ARM: fix a cockup in 48be69a02 (ARM: move signal handlers into a vdso-like page)
|
|
Without this patch, the values for ideality (register 0x4b) and ideality
selection mask (register 0x4c) are inverted.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: stable@vger.kernel.org # 3.9+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
vdso-like page)
Olof reports that noMMU builds error out with:
arch/arm/kernel/signal.c: In function 'setup_return':
arch/arm/kernel/signal.c:413:25: error: 'mm_context_t' has no member named 'sigpage'
This shows one of the evilnesses of IS_ENABLED(). Get rid of it here
and replace it with #ifdef's - and as no noMMU platform can make use
of sigpage, depend on CONIFG_MMU not CONFIG_ARM_MPU.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
