summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2015-09-01ixgbe: Add support for reporting 2.5G link speedMark Rustad2-8/+26
Now that we can do 2.5G link speed, we need to be able to report it. Also change the nested triadic involved in creating the log message to instead use a simpler switch statement to set a string pointer. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01ixgbe: fix bounds checking in ixgbe_setup_tc for 82598Emil Tantilov1-3/+4
This patch resolves an issue where users were not able to dynamically set number of queues for 82598 via ethtool -L Reported-by: Tal Abudi <talabudi@gmail.com> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01ixgbe: support for ethtool set_rxfhTom Barbette3-1/+49
Allows to change the rxfh indirection table and/or key using ethtool interface. Signed-off-by: Tom Barbette <tom.barbette@ulg.ac.be> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01ixgbe: Avoid needless PHY access on copper physMark Rustad2-21/+44
Avoid a needless PHY access on copper phys to save the 10ms wait time for each PHY access. A helper function is introduced to actually do the register access and process the contents. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01ixgbe: cleanup to use cached mask valueDon Skidmore1-6/+1
We already cache this FW/SW semaphore mask so might as well use it for consistency. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01ixgbe: Remove second instance of lan_id variableDon Skidmore2-4/+1
This patch removes the redundant lan_id in the phy struct and uses the bus version. Both variables exist and intend to represent the STATUS register LAN_ID field. However, phy.lan_id is not bit shifted so the phy.lan_id = 0x0 for LAN Id 0 and phy.lan_id = 0x4 for LAN Id 1. Where bus.lan_id is bit shifted so bus.lan_id = 0x0 for LAN Id 0 and bus.lan_id = 0x1 for LAN Id 1. There seems no need for the additional lan_id variable and this should make the code less confusing. Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01ixgbe: use kzalloc for allocating one thingManinder Singh1-1/+1
Use kzalloc rather than kcalloc(1.. The semantic patch that makes this change is as follows: // <smpl> @@ @@ - kcalloc(1, + kzalloc( ...) // </smpl> and removing checkpatch below CHECK: CHECK: Prefer kzalloc(sizeof(*fwd_adapter)...) over kzalloc(sizeof(struct ixgbe_fwd_adapter)...) Signed-off-by: Maninder Singh <maninder1.s@samsung.com> Reviewed-by: Vaneet Narang <v.narang@samsung.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01ixgbe: Remove unused PCI bus typesDon Skidmore1-2/+0
The ixgbe never has as very doubtfully ever will support either PCI or PCI-X devices. So remove the unused types from the ixgbe_bus_type. Thanks to Alex Duyck for suggesting this. Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01ixgbe: add new bus type for intergrated I/O interface (IOSF)Don Skidmore3-1/+12
With this patch we add support for a new bus type ixgbe_bus_type_internal. X550em devices use IOSF and not PCIe bus so this new type is to accommodate them. Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01ixgbe: add get_bus_info method for X550Don Skidmore1-0/+19
Added ixgbe_get_bus_info_X550em to X550 code. ixgbe_get_bus_info_X550em sets bus.width to ixgbe_bus_width_unknown and bus.speed to ixgbe_bus_speed_unknown, because IOSF does not report a PCIe bus width or speed. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01ixgbe: Add support for entering low power link up stateDon Skidmore3-2/+185
When the device is closing or suspending, call ixgbe_enter_lplu to enter low power link up state on devices that support it. When this is done, prevent the phy from being reset in the ixgbe_down path so that link is present when calling ixgbe_enter_lplu. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01ixgbe: Add support for VXLAN RX offloadsMark Rustad4-31/+127
Add support for VXLAN RX offloads for the X55x devices that support them. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01ixgbe: Add support for UDP-encapsulated tx checksum offloadMark Rustad1-12/+54
By using GSO for UDP-encapsulated packets, all ixgbe devices can be directed to generate checksums for the inner headers because the outer UDP checksum can be zero. So point the machinery at the inner headers and have the hardware generate the checksum. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01ixgbe: Check whether FDIRCMD writes actually completeMark Rustad2-24/+40
Wait up to about 100 us for FDIRCMD writes to complete and return failure indications. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01ixgbe: Assign set_phy_power dynamically where neededDon Skidmore2-2/+21
There are various reasons why this method may or may not need to be defined and some of these we don't know until runtime. So we will set the value in get_invariants. Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01ixgbe: add new function to check for management presenceDon Skidmore3-6/+18
This patch adds a support function that will indicate for the existence of management FW. Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-01i40e: Set defport behavior for the Main VSI when in promiscuous modeAnjali Singhai Jain2-8/+30
This fixes bugs where the port is not receiving multicast or VLAN tagged packets when in promiscuous mode. This can occur when a SW bridge is created on top of the device. This also fixes issues where the promiscuous behavior setting was not being preserved across a reset caused by features being enabled or disabled. We are using defport instead of doing a true promiscuous mode because we do not need to receive the SRIOV or VMDq VSI directed traffic which would suck up bandwidth and is really not intended for the SW bridge. In addition, with defport we get VLAN promiscuous behavior which is not possible from the VSI level promiscuous setting. Change-ID: Ie21985eac32d5af1c02e9d71c6430a90d5bab40f Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-08-31tun_dst: Remove opts_sizePravin B Shelar2-2/+0
opts_size is only written and never read. Following patch removes this unused variable. Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31ipv6: send only one NEWLINK when RA causes changesMarius Tomaschewski1-3/+10
Signed-off-by: Marius Tomaschewski <mt@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31gro_cells: remove spinlock protecting receive queuesEric Dumazet1-13/+5
As David pointed out, spinlock are no longer needed to protect the per cpu queues used in gro cells infrastructure. Also use new napi_complete_done() API so that gro_flush_timeout tweaks have an effect. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31net: qmi_wwan: Sierra Wireless MC73xx -> Sierra Wireless MC7304/MC7354David Ward1-2/+2
Other Sierra Wireless MC73xx devices exist, with different USB IDs. Cc: Bjørn Mork <bjorn@mork.no> Signed-off-by: David Ward <david.ward@ll.mit.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31ipv6: send NEWLINK on RA managed/otherconf changesMarius Tomaschewski1-0/+5
The kernel is applying the RA managed/otherconf flags silently and forgets to send ifinfo notify to inform about their change when the router provides a zero reachable_time and retrans_timer as dnsmasq and many routers send it, which just means unspecified by this router and the host should continue using whatever value it is already using. Userspace may monitor the ifinfo notifications to activate dhcpv6. Signed-off-by: Marius Tomaschewski <mt@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31Merge branch 'dsa-port-config'David S. Miller17-39/+255
Andrew Lunn says: ==================== DSA port configuration and status This patchset allows various switch port settings to be configured and port status to be sampled. Some of these patches have been posted before. The first three patches provide infrastructure for configuring a switch ports link speed and duplex from a fixed_link phy. Patch four then uses this infrastructure to allow the CPU and DSA ports of a switch to be configured using a fixed-link property in the device tree. Patches five and six allow a phy-mode property to be specified in the device tree, and allow this to be used for configuring RGMII delays. Patches seven through nine allow link status, for example that of an SFP module, to be read from a gpio. Changes since v1: Rewrite 9/9 so that it hopefully does not regression on 868a4215be9a6d80 ("net: phy: fixed_phy: handle link-down case") ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31net: phy: fixed_phy: Set phy capabilities even when link down.Andrew Lunn1-25/+48
What features a phy supports is masked in genphy_config_init() by looking at the PHYs BMSR register. If the link is down, fixed_phy_update_regs() will only set the auto- negotiation capable bit in BMSR. Thus genphy_config_init() comes to the conclusion the PHY can only perform 10/Half, and masks out the higher speed features. If however the link it up, BMSR is set to indicate the speed the PHY is capable of auto-negotiating, and genphy_config_init() does not mask out the high speed features. To fix this, when the link is down, have fixed_phy_update_regs() leave the link status, auto-negotiation complete, and link partner capabilities unset, but set all the local capabilities depending on the fixed phy speed. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31phy: fixed_phy: Add gpio to determine link up/down.Andrew Lunn9-15/+59
An SFP module may have a link up/down status pin which can be connection to a GPIO line of the host. Add support for reading such an GPIO in the fixed_phy driver. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31dsa: mv88e6xxx: Don't poll forced interfaces for state changesAndrew Lunn1-0/+5
When polling for link status, don't consider ports which have a forced link. Such ports don't monitor their phy or may not even have a phy. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31dsa: mv88e6xxx: Set the RGMII delay based on phy interfaceAndrew Lunn2-0/+12
Some Marvell switches allow the RGMII Rx and Tx clock to be delayed when the port is using RGMII. Have the adjust_link function look at the phy interface type and enable this delay as requested. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31net: dsa: Allow DSA and CPU ports to have a phy-mode propertyAndrew Lunn1-1/+7
It can be useful for DSA and CPU ports to have a phy-mode property, in particular to specify RGMII delays. Parse the property and set it in the fixed-link phydev. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31net: dsa: Allow configuration of CPU & DSA port speeds/duplexAndrew Lunn1-0/+37
By default, DSA and CPU ports are configured to the maximum speed the switch supports. However there can be use cases where the peer devices port is slower. Allow a fixed-link property to be used with the DSA and CPU port in the device tree, and use this information to configure the port. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31phy: fixed_phy: Set supported speed in phydevAndrew Lunn1-0/+12
Set the supported field of the phydev to indicate the speed features of the phy. If the phy is never attached to a netdev, but used in an adjust_link() function, the speed will be incorrectly evaluated to 10/half rather than the correct speed/duplex. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31dsa: mv88e6xxx: Allow speed/duplex of port to be configuredAndrew Lunn6-0/+64
The current code sets user ports to perform auto negotiation using the phy. CPU and DSA ports are configured to full duplex and maximum speed the switch supports. There are however use cases where the CPU has a slower port, and when user ports have SFP modules with fixed speed. In these cases, port settings to be read from a fixed_phy devices. The switch driver then needs to implement the adjust_link op, so the port settings can be set. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31net: phy: Allow PHY devices to identify themselves as Ethernet switches, etc.Florian Fainelli2-0/+13
Some Ethernet MAC drivers using the PHY library require the hardcoding of link parameters when interfaced to a switch device, SFP module, switch to switch port, etc. This has typically lead to various ad-hoc implementations looking like this: - using a "fixed PHY" emulated device, which will provide link indication towards the Ethernet MAC driver and hardware - pretend there is no PHY and hardcode link parameters, ala mv643x_eth Based on that, it is desireable to have the PHY drivers advertise the correct link parameters, just like regular Ethernet PHYs towards their CPU Ethernet MAC drivers, however, Ethernet MAC drivers should be able to tell whether this link should be monitored or not. In the context of an Ethernet switch, SFP module, switch to switch link, we do not need to monitor this link since it should be always up. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31mpls: fix mpls_net_init memory leakNikolay Aleksandrov1-1/+3
Fix a memory leak in the mpls netns init function in case of failure. If register_net_sysctl fails then we need to free the ctl_table. Fixes: 7720c01f3f59 ("mpls: Add a sysctl to control the size of the mpls label table") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31net: Add tos to validate source tracepointDavid Ahern1-2/+4
TOS is another key aspect of the lookup passed to fib_validate_source. Add it to the tracepoint. Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31lib: move strncpy_from_unsafe() into mm/maccess.cAlexei Starovoitov2-41/+41
To fix build errors: kernel/built-in.o: In function `bpf_trace_printk': bpf_trace.c:(.text+0x11a254): undefined reference to `strncpy_from_unsafe' kernel/built-in.o: In function `fetch_memory_string': trace_kprobe.c:(.text+0x11acf8): undefined reference to `strncpy_from_unsafe' move strncpy_from_unsafe() next to probe_kernel_read/write() which use the same memory access style. Reported-by: Fengguang Wu <fengguang.wu@intel.com> Reported-by: Guenter Roeck <linux@roeck-us.net> Fixes: 1a6877b9c0c2 ("lib: introduce strncpy_from_unsafe()") Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31Merge branch 'per-route-dctcp-receive-side'David S. Miller8-56/+101
Daniel Borkmann says: ==================== tcp: receive-side per route dctcp handling Original cover letter: Currently, the following case doesn't use DCTCP, even if it should: - responder has f.e. cubic as system wide default - 'ip route congctl dctcp $src' was set Then, DCTCP is NOT used if a DCTCP sender attempts to connect from a host in the $src range: ECT(0) is set, but listen_sk is not dctcp, so we fail the INET_ECN_is_not_ect sanity check. We also have to examine the dst used for the SYN/ACK reply to make this case work. In order to minimize additional cost, store the 'ecn is must have' information is the dst_features field. The set targets -next instead of -net since this doesn't seem to be a serious bug and to give the change more soak time until it hits linus tree. v1 -> v2: - Addressed Dave's feedback, not exposing any bits to user space - Added patch 3 to reject incorrect configurations - Rest as is, rebased and retested ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31tcp: use dctcp if enabled on the route to the initiatorDaniel Borkmann7-9/+36
Currently, the following case doesn't use DCTCP, even if it should: A responder has f.e. Cubic as system wide default, but for a specific route to the initiating host, DCTCP is being set in RTAX_CC_ALGO. The initiating host then uses DCTCP as congestion control, but since the initiator sets ECT(0), tcp_ecn_create_request() doesn't set ecn_ok, and we have to fall back to Reno after 3WHS completes. We were thinking on how to solve this in a minimal, non-intrusive way without bloating tcp_ecn_create_request() needlessly: lets cache the CA ecn option flag in RTAX_FEATURES. In other words, when ECT(0) is set on the SYN packet, set ecn_ok=1 iff route RTAX_FEATURES contains the unexposed (internal-only) DST_FEATURE_ECN_CA. This allows to only do a single metric feature lookup inside tcp_ecn_create_request(). Joint work with Florian Westphal. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31fib, fib6: reject invalid feature bitsDaniel Borkmann3-4/+11
Feature bits that are invalid should not be accepted by the kernel, only the lower 4 bits may be configured, but not the remaining ones. Even from these 4, 2 of them are unused. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31net: fib6: reduce identation in ip6_convert_metricsDaniel Borkmann1-16/+16
Reduce the identation a bit, there's no need to artificically have it increased. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31net: fib: move metrics parsing to a helperFlorian Westphal1-30/+41
fib_create_info() is already quite large, so before adding more code to the metrics section move that to a helper, similar to ip6_convert_metrics. Suggested-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31IGMP: Document igmp_link_local_mcast_reportsPhilip Downey1-0/+5
Document the addition of a new sysctl variable which controls the generation of IGMP reports for link local multicast groups in the 224.0.0.X range. IGMP reports for local multicast groups can now be optionally inhibited by setting the value to zero e.g.: echo 0 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports To retain backwards compatibility the previous behaviour is retained by default on system boot or reverted by setting the value back to non-zero. Signed-off-by: Philip Downey <pdowney@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31ip-tunnel: Use API to access tunnel metadata options.Pravin B Shelar16-112/+100
Currently tun-info options pointer is used in few cases to pass options around. But tunnel options can be accessed using ip_tunnel_info_opts() API without using the pointer. Following patch removes the redundant pointer and consistently make use of API. Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Thomas Graf <tgraf@suug.ch> Reviewed-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-31ipv4: fix 32b buildMadalin Bucur1-1/+1
Address remaining issue after 80ec192. Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-30ipv4: Fix 32-bit build.David S. Miller1-2/+2
net/ipv4/af_inet.c: In function 'snmp_get_cpu_field64': >> net/ipv4/af_inet.c:1486:26: error: 'offt' undeclared (first use in this function) v = *(((u64 *)bhptr) + offt); ^ net/ipv4/af_inet.c:1486:26: note: each undeclared identifier is reported only once for each function it appears in net/ipv4/af_inet.c: In function 'snmp_fold_field64': >> net/ipv4/af_inet.c:1499:39: error: 'offct' undeclared (first use in this function) res += snmp_get_cpu_field(mib, cpu, offct, syncp_offset); ^ >> net/ipv4/af_inet.c:1499:10: error: too many arguments to function 'snmp_get_cpu_field' res += snmp_get_cpu_field(mib, cpu, offct, syncp_offset); ^ net/ipv4/af_inet.c:1455:5: note: declared here u64 snmp_get_cpu_field(void __percpu *mib, int cpu, int offt) ^ Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-30netlink: rx mmap: fix POLLIN conditionKen-ichirou MATSUZAWA1-12/+16
Poll() returns immediately after setting the kernel current frame (ring->head) to SKIP from user space even though there is no new frame. And in a case of all frames is VALID, user space program unintensionally sets (only) kernel current frame to UNUSED, then calls poll(), it will not return immediately even though there are VALID frames. To avoid situations like above, I think we need to scan all frames to find VALID frames at poll() like netlink_alloc_skb(), netlink_forward_ring() finding an UNUSED frame at skb allocation. Signed-off-by: Ken-ichirou MATSUZAWA <chamas@h4.dion.ne.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-30Merge branch 'thunderx-features-fixes'David S. Miller9-329/+911
Aleksey Makarov says: ==================== net: thunderx: New features and fixes v2: - The unused affinity_mask field of the structure cmp_queue has been deleted. (thanks to David Miller) - The unneeded initializers have been dropped. (thanks to Alexey Klimov) - The commit message "net: thunderx: Rework interrupt handling" has been fixed. (thanks to Alexey Klimov) ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-30net: thunderx: Support for internal loopback modeSunil Goutham5-0/+97
Support for setting VF's corresponding BGX LMAC in internal loopback mode. This mode can be used for verifying basic HW functionality such as packet I/O, RX checksum validation, CQ/RBDR interrupts, stats e.t.c. Useful when DUT has no external network connectivity. 'loopback' mode can be enabled or disabled via ethtool. Note: This feature is not supported when no of VFs enabled are morethan no of physical interfaces i.e active BGX LMACs Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-30net: thunderx: Support for upto 96 queues for a VFSunil Goutham5-84/+505
This patch adds support for handling multiple qsets assigned to a single VF. There by increasing no of queues from earlier 8 to max no of CPUs in the system i.e 48 queues on a single node and 96 on dual node system. User doesn't have option to assign which Qsets/VFs to be merged. Upon request from VF, PF assigns next free Qsets as secondary qsets. To maintain current behavior no of queues is kept to 8 by default which can be increased via ethtool. If user wants to unbind NICVF driver from a secondary Qset then it should be done after tearing down primary VF's interface. Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com> Signed-off-by: Robert Richter <rrichter@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-30net: thunderx: Rework interrupt handlingSunil Goutham3-72/+102
Rework interrupt handler to avoid checking IRQ affinity of CQ interrupts. Now separate handlers are registered for each IRQ including RBDR. Register interrupt handlers for only those which are being used. Add nicvf_dump_intr_status() and use it in irq handlers. Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-30net: thunderx: Support for HW VLAN strippingSunil Goutham4-7/+55
This patch configures HW to strip 802.1Q header if found in a receiving packet. The stripped VLAN ID and TCI information is passed on to software via CQE_RX. Also sets netdev's 'vlan_features' so that other HW offload features can be used for tagged packets. This offload feature can be enabled or disabled via ethtool. Network stack normally ignores RPS for 802.1Q packets and hence low throughput. With this offload enabled throughput for tagged packets will be almost same as normal packets. Note: This patch doesn't enable HW VLAN insertion for transmit packets. Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-25 23:00:30 +0000