summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2022-02-10selftests: netfilter: synproxy test requires nf_conntrackPablo Neira Ayuso1-0/+2
Otherwise, this test does not find the sysctl entry in place: sysctl: cannot stat /proc/sys/net/netfilter/nf_conntrack_tcp_loose: No such file or directory iperf3: error - unable to send control message: Bad file descriptor FAIL: iperf3 returned an error Fixes: 7152303cbec4 ("selftests: netfilter: add synproxy test") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2022-02-10netfilter: nft_synproxy: unregister hooks on init error pathPablo Neira Ayuso1-1/+3
Disable the IPv4 hooks if the IPv6 hooks fail to be registered. Fixes: ad49d86e07a4 ("netfilter: nf_tables: Add synproxy support") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2022-02-09selftests: netfilter: fix exit value for nft_concat_rangeHangbin Liu1-1/+1
When the nft_concat_range test failed, it exit 1 in the code specifically. But when part of, or all of the test passed, it will failed the [ ${passed} -eq 0 ] check and thus exit with 1, which is the same exit value with failure result. Fix it by exit 0 when passed is not 0. Fixes: 611973c1e06f ("selftests: netfilter: Introduce tests for sets with range concatenation") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2022-02-09netfilter: xt_socket: fix a typo in socket_mt_destroy()Eric Dumazet1-1/+1
Calling nf_defrag_ipv4_disable() instead of nf_defrag_ipv6_disable() was probably not the intent. I found this by code inspection, while chasing a possible issue in TPROXY. Fixes: de8c12110a13 ("netfilter: disable defrag once its no longer needed") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2022-02-09selftests: netfilter: add synproxy testFlorian Westphal2-1/+116
Simple test for synproxy feature, iperf3 should be intercepted by synproxy netns, but connection should still succeed. Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2022-02-08nfp: flower: fix ida_idx not being releasedLouis Peens1-4/+8
When looking for a global mac index the extra NFP_TUN_PRE_TUN_IDX_BIT that gets set if nfp_flower_is_supported_bridge is true is not taken into account. Consequently the path that should release the ida_index in cleanup is never triggered, causing messages like: nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex. nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex. nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex. after NFP_MAX_MAC_INDEX number of reconfigs. Ultimately this lead to new tunnel flows not being offloaded. Fix this by unsetting the NFP_TUN_PRE_TUN_IDX_BIT before checking if the port is of type OTHER. Fixes: 2e0bc7f3cb55 ("nfp: flower: encode mac indexes with pre-tunnel rule check") Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20220208101453.321949-1-simon.horman@corigine.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-08ipmr,ip6mr: acquire RTNL before calling ip[6]mr_free_table() on failure pathEric Dumazet2-0/+4
ip[6]mr_free_table() can only be called under RTNL lock. RTNL: assertion failed at net/core/dev.c (10367) WARNING: CPU: 1 PID: 5890 at net/core/dev.c:10367 unregister_netdevice_many+0x1246/0x1850 net/core/dev.c:10367 Modules linked in: CPU: 1 PID: 5890 Comm: syz-executor.2 Not tainted 5.16.0-syzkaller-11627-g422ee58dc0ef #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:unregister_netdevice_many+0x1246/0x1850 net/core/dev.c:10367 Code: 0f 85 9b ee ff ff e8 69 07 4b fa ba 7f 28 00 00 48 c7 c6 00 90 ae 8a 48 c7 c7 40 90 ae 8a c6 05 6d b1 51 06 01 e8 8c 90 d8 01 <0f> 0b e9 70 ee ff ff e8 3e 07 4b fa 4c 89 e7 e8 86 2a 59 fa e9 ee RSP: 0018:ffffc900046ff6e0 EFLAGS: 00010286 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: ffff888050f51d00 RSI: ffffffff815fa008 RDI: fffff520008dfece RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: ffffffff815f3d6e R11: 0000000000000000 R12: 00000000fffffff4 R13: dffffc0000000000 R14: ffffc900046ff750 R15: ffff88807b7dc000 FS: 00007f4ab736e700(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fee0b4f8990 CR3: 000000001e7d2000 CR4: 00000000003506e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> mroute_clean_tables+0x244/0xb40 net/ipv6/ip6mr.c:1509 ip6mr_free_table net/ipv6/ip6mr.c:389 [inline] ip6mr_rules_init net/ipv6/ip6mr.c:246 [inline] ip6mr_net_init net/ipv6/ip6mr.c:1306 [inline] ip6mr_net_init+0x3f0/0x4e0 net/ipv6/ip6mr.c:1298 ops_init+0xaf/0x470 net/core/net_namespace.c:140 setup_net+0x54f/0xbb0 net/core/net_namespace.c:331 copy_net_ns+0x318/0x760 net/core/net_namespace.c:475 create_new_namespaces+0x3f6/0xb20 kernel/nsproxy.c:110 copy_namespaces+0x391/0x450 kernel/nsproxy.c:178 copy_process+0x2e0c/0x7300 kernel/fork.c:2167 kernel_clone+0xe7/0xab0 kernel/fork.c:2555 __do_sys_clone+0xc8/0x110 kernel/fork.c:2672 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f4ab89f9059 Code: Unable to access opcode bytes at RIP 0x7f4ab89f902f. RSP: 002b:00007f4ab736e118 EFLAGS: 00000206 ORIG_RAX: 0000000000000038 RAX: ffffffffffffffda RBX: 00007f4ab8b0bf60 RCX: 00007f4ab89f9059 RDX: 0000000020000280 RSI: 0000000020000270 RDI: 0000000040200000 RBP: 00007f4ab8a5308d R08: 0000000020000300 R09: 0000000020000300 R10: 00000000200002c0 R11: 0000000000000206 R12: 0000000000000000 R13: 00007ffc3977cc1f R14: 00007f4ab736e300 R15: 0000000000022000 </TASK> Fixes: f243e5a7859a ("ipmr,ip6mr: call ip6mr_free_table() on failure path") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Cong Wang <cong.wang@bytedance.com> Reported-by: syzbot <syzkaller@googlegroups.com> Link: https://lore.kernel.org/r/20220208053451.2885398-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-08net: ethernet: litex: Add the dependency on HAS_IOMEMCai Huoqing1-1/+1
The LiteX driver uses devm io function API which needs HAS_IOMEM enabled, so add the dependency on HAS_IOMEM. Fixes: ee7da21ac4c3 ("net: Add driver for LiteX's LiteETH network interface") Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev> Link: https://lore.kernel.org/r/20220208013308.6563-1-cai.huoqing@linux.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-08ibmvnic: don't release napi in __ibmvnic_open()Sukadev Bhattiprolu1-4/+9
If __ibmvnic_open() encounters an error such as when setting link state, it calls release_resources() which frees the napi structures needlessly. Instead, have __ibmvnic_open() only clean up the work it did so far (i.e. disable napi and irqs) and leave the rest to the callers. If caller of __ibmvnic_open() is ibmvnic_open(), it should release the resources immediately. If the caller is do_reset() or do_hard_reset(), they will release the resources on the next reset. This fixes following crash that occurred when running the drmgr command several times to add/remove a vnic interface: [102056] ibmvnic 30000003 env3: Disabling rx_scrq[6] irq [102056] ibmvnic 30000003 env3: Disabling rx_scrq[7] irq [102056] ibmvnic 30000003 env3: Replenished 8 pools Kernel attempted to read user page (10) - exploit attempt? (uid: 0) BUG: Kernel NULL pointer dereference on read at 0x00000010 Faulting instruction address: 0xc000000000a3c840 Oops: Kernel access of bad area, sig: 11 [#1] LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries ... CPU: 9 PID: 102056 Comm: kworker/9:2 Kdump: loaded Not tainted 5.16.0-rc5-autotest-g6441998e2e37 #1 Workqueue: events_long __ibmvnic_reset [ibmvnic] NIP: c000000000a3c840 LR: c0080000029b5378 CTR: c000000000a3c820 REGS: c0000000548e37e0 TRAP: 0300 Not tainted (5.16.0-rc5-autotest-g6441998e2e37) MSR: 8000000000009033 <SF,EE,ME,IR,DR,RI,LE> CR: 28248484 XER: 00000004 CFAR: c0080000029bdd24 DAR: 0000000000000010 DSISR: 40000000 IRQMASK: 0 GPR00: c0080000029b55d0 c0000000548e3a80 c0000000028f0200 0000000000000000 ... NIP [c000000000a3c840] napi_enable+0x20/0xc0 LR [c0080000029b5378] __ibmvnic_open+0xf0/0x430 [ibmvnic] Call Trace: [c0000000548e3a80] [0000000000000006] 0x6 (unreliable) [c0000000548e3ab0] [c0080000029b55d0] __ibmvnic_open+0x348/0x430 [ibmvnic] [c0000000548e3b40] [c0080000029bcc28] __ibmvnic_reset+0x500/0xdf0 [ibmvnic] [c0000000548e3c60] [c000000000176228] process_one_work+0x288/0x570 [c0000000548e3d00] [c000000000176588] worker_thread+0x78/0x660 [c0000000548e3da0] [c0000000001822f0] kthread+0x1c0/0x1d0 [c0000000548e3e10] [c00000000000cf64] ret_from_kernel_thread+0x5c/0x64 Instruction dump: 7d2948f8 792307e0 4e800020 60000000 3c4c01eb 384239e0 f821ffd1 39430010 38a0fff6 e92d1100 f9210028 39200000 <e9030010> f9010020 60420000 e9210020 ---[ end trace 5f8033b08fd27706 ]--- Fixes: ed651a10875f ("ibmvnic: Updated reset handling") Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Reviewed-by: Dany Madden <drt@linux.ibm.com> Link: https://lore.kernel.org/r/20220208001918.900602-1-sukadev@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-08Merge branch 'more-dsa-fixes-for-devres-mdiobus_-alloc-register'Jakub Kicinski7-14/+32
Vladimir Oltean says: ==================== More DSA fixes for devres + mdiobus_{alloc,register} The initial patch series "[net,0/2] Fix mdiobus users with devres" https://patchwork.kernel.org/project/netdevbpf/cover/20210920214209.1733768-1-vladimir.oltean@nxp.com/ fixed some instances where DSA drivers on slow buses (SPI, I2C) trigger a panic (changed since then to a warn) in mdiobus_free. That was due to devres calling mdiobus_free() with no prior mdiobus_unregister(), which again was due to commit ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()") by Bartosz Golaszewski. Rafael Richter and Daniel Klauer report yet another variation on that theme, but this time it applies to any DSA switch driver, not just those on buses which have a "->shutdown() calls ->remove() which unregisters children" sequence. Their setup is that of an LX2160A DPAA2 SoC driving a Marvell DSA switch (MDIO). DPAA2 Ethernet drivers probe on the "fsl-mc" bus (drivers/bus/fsl-mc/fsl-mc-bus.c). This bus is meant to be the kernel-side representation of the networking objects kept by the Management Complex (MC) firmware. The fsl-mc bus driver has this pattern: static void fsl_mc_bus_shutdown(struct platform_device *pdev) { fsl_mc_bus_remove(pdev); } which proceeds to remove the children on the bus. Among those children, the dpaa2-eth network driver. When dpaa2-eth is a DSA master, this removal of the master on shutdown trips up the device link created by dsa_master_setup(), and as such, the Marvell switch is also removed. From this point on, readers can revisit the description of commits 74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres") since the prerequisites for the BUG_ON in mdiobus_free() have been accomplished if there is a devres mismatch between mdiobus_alloc() and mdiobus_register(). Most DSA drivers have this kind of mismatch, and upon my initial assessment I had not realized the possibility described above, so I didn't fix it. This patch series walks through all drivers and makes them use either fully devres, or no devres. I am aware that there are DSA drivers that are only known to be tested with a single DSA master, so some patches are probably overkill for them. But code is copy-pasted from so many sources without fully understanding the differences, that I think it's better to not leave an in-tree source of inspiration that may lead to subtle breakage if not adapted properly. ==================== Link: https://lore.kernel.org/r/20220207161553.579933-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-08net: dsa: lantiq_gswip: don't use devres for mdiobusVladimir Oltean1-3/+11
As explained in commits: 74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The GSWIP switch is a platform device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the GSWIP switch driver on shutdown. So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The gswip driver has the code structure in place for orderly mdiobus removal, so just replace devm_mdiobus_alloc() with the non-devres variant, and add manual free where necessary, to ensure that we don't let devres free a still-registered bus. Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-08net: dsa: mt7530: fix kernel bug in mdiobus_free() when unbindingVladimir Oltean1-1/+1
Nobody in this driver calls mdiobus_unregister(), which is necessary if mdiobus_register() completes successfully. So if the devres callbacks that free the mdiobus get invoked (this is the case when unbinding the driver), mdiobus_free() will BUG if the mdiobus is still registered, which it is. My speculation is that this is due to the fact that prior to commit ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()") from June 2020, _devm_mdiobus_free() used to call mdiobus_unregister(). But at the time that the mt7530 support was introduced in May 2021, the API was already changed. It's therefore likely that the blamed patch was developed on an older tree, and incorrectly adapted to net-next. This makes the Fixes: tag correct. Fix the problem by using the devres variant of mdiobus_register. Fixes: ba751e28d442 ("net: dsa: mt7530: add interrupt support") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-08net: dsa: seville: register the mdiobus under devresVladimir Oltean1-2/+3
As explained in commits: 74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The Seville VSC9959 switch is a platform device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the seville switch driver on shutdown. So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The seville driver has a code structure that could accommodate both the mdiobus_unregister and mdiobus_free calls, but it has an external dependency upon mscc_miim_setup() from mdio-mscc-miim.c, which calls devm_mdiobus_alloc_size() on its behalf. So rather than restructuring that, and exporting yet one more symbol mscc_miim_teardown(), let's work with devres and replace of_mdiobus_register with the devres variant. When we use all-devres, we can ensure that devres doesn't free a still-registered bus (it either runs both callbacks, or none). Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-08net: dsa: felix: don't use devres for mdiobusVladimir Oltean1-1/+3
As explained in commits: 74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The Felix VSC9959 switch is a PCI device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the felix switch driver on shutdown. So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The felix driver has the code structure in place for orderly mdiobus removal, so just replace devm_mdiobus_alloc_size() with the non-devres variant, and add manual free where necessary, to ensure that we don't let devres free a still-registered bus. Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-08net: dsa: bcm_sf2: don't use devres for mdiobusVladimir Oltean1-2/+5
As explained in commits: 74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The Starfighter 2 is a platform device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the bcm_sf2 switch driver on shutdown. So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The bcm_sf2 driver has the code structure in place for orderly mdiobus removal, so just replace devm_mdiobus_alloc() with the non-devres variant, and add manual free where necessary, to ensure that we don't let devres free a still-registered bus. Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-08net: dsa: ar9331: register the mdiobus under devresVladimir Oltean1-2/+1
As explained in commits: 74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The ar9331 is an MDIO device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the ar9331 switch driver on shutdown. So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The ar9331 driver doesn't have a complex code structure for mdiobus removal, so just replace of_mdiobus_register with the devres variant in order to be all-devres and ensure that we don't free a still-registered bus. Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-08net: dsa: mv88e6xxx: don't use devres for mdiobusVladimir Oltean1-3/+8
As explained in commits: 74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres") 5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres") mdiobus_free() will panic when called from devm_mdiobus_free() <- devres_release_all() <- __device_release_driver(), and that mdiobus was not previously unregistered. The mv88e6xxx is an MDIO device, so the initial set of constraints that I thought would cause this (I2C or SPI buses which call ->remove on ->shutdown) do not apply. But there is one more which applies here. If the DSA master itself is on a bus that calls ->remove from ->shutdown (like dpaa2-eth, which is on the fsl-mc bus), there is a device link between the switch and the DSA master, and device_links_unbind_consumers() will unbind the Marvell switch driver on shutdown. systemd-shutdown[1]: Powering off. mv88e6085 0x0000000008b96000:00 sw_gl0: Link is Down fsl-mc dpbp.9: Removing from iommu group 7 fsl-mc dpbp.8: Removing from iommu group 7 ------------[ cut here ]------------ kernel BUG at drivers/net/phy/mdio_bus.c:677! Internal error: Oops - BUG: 0 [#1] PREEMPT SMP Modules linked in: CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00040-gdc05f73788e5 #15 pc : mdiobus_free+0x44/0x50 lr : devm_mdiobus_free+0x10/0x20 Call trace: mdiobus_free+0x44/0x50 devm_mdiobus_free+0x10/0x20 devres_release_all+0xa0/0x100 __device_release_driver+0x190/0x220 device_release_driver_internal+0xac/0xb0 device_links_unbind_consumers+0xd4/0x100 __device_release_driver+0x4c/0x220 device_release_driver_internal+0xac/0xb0 device_links_unbind_consumers+0xd4/0x100 __device_release_driver+0x94/0x220 device_release_driver+0x28/0x40 bus_remove_device+0x118/0x124 device_del+0x174/0x420 fsl_mc_device_remove+0x24/0x40 __fsl_mc_device_remove+0xc/0x20 device_for_each_child+0x58/0xa0 dprc_remove+0x90/0xb0 fsl_mc_driver_remove+0x20/0x5c __device_release_driver+0x21c/0x220 device_release_driver+0x28/0x40 bus_remove_device+0x118/0x124 device_del+0x174/0x420 fsl_mc_bus_remove+0x80/0x100 fsl_mc_bus_shutdown+0xc/0x1c platform_shutdown+0x20/0x30 device_shutdown+0x154/0x330 kernel_power_off+0x34/0x6c __do_sys_reboot+0x15c/0x250 __arm64_sys_reboot+0x20/0x30 invoke_syscall.constprop.0+0x4c/0xe0 do_el0_svc+0x4c/0x150 el0_svc+0x24/0xb0 el0t_64_sync_handler+0xa8/0xb0 el0t_64_sync+0x178/0x17c So the same treatment must be applied to all DSA switch drivers, which is: either use devres for both the mdiobus allocation and registration, or don't use devres at all. The Marvell driver already has a good structure for mdiobus removal, so just plug in mdiobus_free and get rid of devres. Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()") Reported-by: Rafael Richter <Rafael.Richter@gin.de> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Daniel Klauer <daniel.klauer@gin.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-08bonding: pair enable_port with slave_arr_updatesMahesh Bandewar1-1/+2
When 803.2ad mode enables a participating port, it should update the slave-array. I have observed that the member links are participating and are part of the active aggregator while the traffic is egressing via only one member link (in a case where two links are participating). Via kprobes I discovered that slave-arr has only one link added while the other participating link wasn't part of the slave-arr. I couldn't see what caused that situation but the simple code-walk through provided me hints that the enable_port wasn't always associated with the slave-array update. Fixes: ee6377147409 ("bonding: Simplify the xmit function for modes that use xmit_hash") Signed-off-by: Mahesh Bandewar <maheshb@google.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Link: https://lore.kernel.org/r/20220207222901.1795287-1-maheshb@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-08gve: Recording rx queue before sending to napiTao Liu1-0/+1
This caused a significant performance degredation when using generic XDP with multiple queues. Fixes: f5cedc84a30d2 ("gve: Add transmit and receive support") Signed-off-by: Tao Liu <xliutaox@google.com> Link: https://lore.kernel.org/r/20220207175901.2486596-1-jeroendb@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-07net: phy: marvell: Fix RGMII Tx/Rx delays setting in 88e1121-compatible PHYsPavel Parkhomenko1-4/+6
It is mandatory for a software to issue a reset upon modifying RGMII Receive Timing Control and RGMII Transmit Timing Control bit fields of MAC Specific Control register 2 (page 2, register 21) otherwise the changes won't be perceived by the PHY (the same is applicable for a lot of other registers). Not setting the RGMII delays on the platforms that imply it' being done on the PHY side will consequently cause the traffic loss. We discovered that the denoted soft-reset is missing in the m88e1121_config_aneg() method for the case if the RGMII delays are modified but the MDIx polarity isn't changed or the auto-negotiation is left enabled, thus causing the traffic loss on our platform with Marvell Alaska 88E1510 installed. Let's fix that by issuing the soft-reset if the delays have been actually set in the m88e1121_config_aneg_rgmii_delays() method. Cc: stable@vger.kernel.org Fixes: d6ab93364734 ("net: phy: marvell: Avoid unnecessary soft reset") Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20220205203932.26899-1-Pavel.Parkhomenko@baikalelectronics.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-07net/smc: use GFP_ATOMIC allocation in smc_pnet_add_eth()Eric Dumazet1-1/+1
My last patch moved the netdev_tracker_alloc() call to a section protected by a write_lock(). I should have replaced GFP_KERNEL with GFP_ATOMIC to avoid the infamous: BUG: sleeping function called from invalid context at include/linux/sched/mm.h:256 Fixes: 28f922213886 ("net/smc: fix ref_tracker issue in smc_pnet_add()") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-02-06net/smc: fix ref_tracker issue in smc_pnet_add()Eric Dumazet1-3/+5
I added the netdev_tracker_alloc() right after ndev was stored into the newly allocated object: new_pe->ndev = ndev; if (ndev) netdev_tracker_alloc(ndev, &new_pe->dev_tracker, GFP_KERNEL); But I missed that later, we could end up freeing new_pe, then calling dev_put(ndev) to release the reference on ndev. The new_pe->dev_tracker would not be freed. To solve this issue, move the netdev_tracker_alloc() call to the point we know for sure new_pe will be kept. syzbot report (on net-next tree, but the bug is present in net tree) WARNING: CPU: 0 PID: 6019 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0 lib/refcount.c:31 Modules linked in: CPU: 0 PID: 6019 Comm: syz-executor.3 Not tainted 5.17.0-rc2-syzkaller-00650-g5a8fb33e5305 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:refcount_warn_saturate+0xbf/0x1e0 lib/refcount.c:31 Code: 1d f4 70 a0 09 31 ff 89 de e8 4d bc 99 fd 84 db 75 e0 e8 64 b8 99 fd 48 c7 c7 20 0c 06 8a c6 05 d4 70 a0 09 01 e8 9e 4e 28 05 <0f> 0b eb c4 e8 48 b8 99 fd 0f b6 1d c3 70 a0 09 31 ff 89 de e8 18 RSP: 0018:ffffc900043b7400 EFLAGS: 00010282 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000040000 RSI: ffffffff815fb318 RDI: fffff52000876e72 RBP: 0000000000000004 R08: 0000000000000000 R09: 0000000000000000 R10: ffffffff815f507e R11: 0000000000000000 R12: 1ffff92000876e85 R13: 0000000000000000 R14: ffff88805c1c6600 R15: 0000000000000000 FS: 00007f1ef6feb700(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000001b2d02b000 CR3: 00000000223f4000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __refcount_dec include/linux/refcount.h:344 [inline] refcount_dec include/linux/refcount.h:359 [inline] ref_tracker_free+0x53f/0x6c0 lib/ref_tracker.c:119 netdev_tracker_free include/linux/netdevice.h:3867 [inline] dev_put_track include/linux/netdevice.h:3884 [inline] dev_put_track include/linux/netdevice.h:3880 [inline] dev_put include/linux/netdevice.h:3910 [inline] smc_pnet_add_eth net/smc/smc_pnet.c:399 [inline] smc_pnet_enter net/smc/smc_pnet.c:493 [inline] smc_pnet_add+0x5fc/0x15f0 net/smc/smc_pnet.c:556 genl_family_rcv_msg_doit+0x228/0x320 net/netlink/genetlink.c:731 genl_family_rcv_msg net/netlink/genetlink.c:775 [inline] genl_rcv_msg+0x328/0x580 net/netlink/genetlink.c:792 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2494 genl_rcv+0x24/0x40 net/netlink/genetlink.c:803 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline] netlink_unicast+0x539/0x7e0 net/netlink/af_netlink.c:1343 netlink_sendmsg+0x904/0xe00 net/netlink/af_netlink.c:1919 sock_sendmsg_nosec net/socket.c:705 [inline] sock_sendmsg+0xcf/0x120 net/socket.c:725 ____sys_sendmsg+0x6e8/0x810 net/socket.c:2413 ___sys_sendmsg+0xf3/0x170 net/socket.c:2467 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2496 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae Fixes: b60645248af3 ("net/smc: add net device tracker to struct smc_pnetentry") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-02-06net: phy: marvell: Fix MDI-x polarity setting in 88e1118-compatible PHYsPavel Parkhomenko1-4/+3
When setting up autonegotiation for 88E1118R and compatible PHYs, a software reset of PHY is issued before setting up polarity. This is incorrect as changes of MDI Crossover Mode bits are disruptive to the normal operation and must be followed by a software reset to take effect. Let's patch m88e1118_config_aneg() to fix the issue mentioned before by invoking software reset of the PHY just after setting up MDI-x polarity. Fixes: 605f196efbf8 ("phy: Add support for Marvell 88E1118 PHY") Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Suggested-by: Andrew Lunn <andrew@lunn.ch> Cc: stable@vger.kernel.org Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-02-05net: mscc: ocelot: fix all IP traffic getting trapped to CPU with PTP over IPVladimir Oltean1-0/+8
The filters for the PTP trap keys are incorrectly configured, in the sense that is2_entry_set() only looks at trap->key.ipv4.dport or trap->key.ipv6.dport if trap->key.ipv4.proto or trap->key.ipv6.proto is set to IPPROTO_TCP or IPPROTO_UDP. But we don't do that, so is2_entry_set() goes through the "else" branch of the IP protocol check, and ends up installing a rule for "Any IP protocol match" (because msk is also 0). The UDP port is ignored. This means that when we run "ptp4l -i swp0 -4", all IP traffic is trapped to the CPU, which hinders bridging. Fix this by specifying the IP protocol in the VCAP IS2 filters for PTP over UDP. Fixes: 96ca08c05838 ("net: mscc: ocelot: set up traps for PTP packets") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-02-04tcp: take care of mixed splice()/sendmsg(MSG_ZEROCOPY) caseEric Dumazet1-14/+19
syzbot found that mixing sendpage() and sendmsg(MSG_ZEROCOPY) calls over the same TCP socket would again trigger the infamous warning in inet_sock_destruct() WARN_ON(sk_forward_alloc_get(sk)); While Talal took into account a mix of regular copied data and MSG_ZEROCOPY one in the same skb, the sendpage() path has been forgotten. We want the charging to happen for sendpage(), because pages could be coming from a pipe. What is missing is the downgrading of pure zerocopy status to make sure sk_forward_alloc will stay synced. Add tcp_downgrade_zcopy_pure() helper so that we can use it from the two callers. Fixes: 9b65b17db723 ("net: avoid double accounting for pure zerocopy skbs") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Talal Ahmad <talalahmad@google.com> Cc: Arjun Roy <arjunroy@google.com> Cc: Willem de Bruijn <willemb@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Link: https://lore.kernel.org/r/20220203225547.665114-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nfJakub Kicinski7-27/+61
Pablo Neira Ayuso says: ==================== Netfilter fixes for net 1) Don't refresh timeout for SCTP flows in CLOSED state. 2) Don't allow access to transport header if fragment offset is set on. 3) Reinitialize internal conntrack state for retransmitted TCP syn-ack packet. 4) Update MAINTAINER file to add the Netfilter group tree. Moving forward, Florian Westphal has access to this tree so he can also send pull requests. 5) Set on IPS_HELPER for entries created via ctnetlink, otherwise NAT might zap it. All patches from Florian Westphal. * git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf: netfilter: ctnetlink: disable helper autoassign MAINTAINERS: netfilter: update git links netfilter: conntrack: re-init state for retransmitted syn-ack netfilter: conntrack: move synack init code to helper netfilter: nft_payload: don't allow th access for fragments netfilter: conntrack: don't refresh sctp entries in closed state ==================== Link: https://lore.kernel.org/r/20220204151903.320786-1-pablo@netfilter.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-04ixgbevf: Require large buffers for build_skb on 82599VFSamuel Mendoza-Jonas1-6/+7
From 4.17 onwards the ixgbevf driver uses build_skb() to build an skb around new data in the page buffer shared with the ixgbe PF. This uses either a 2K or 3K buffer, and offsets the DMA mapping by NET_SKB_PAD + NET_IP_ALIGN. When using a smaller buffer RXDCTL is set to ensure the PF does not write a full 2K bytes into the buffer, which is actually 2K minus the offset. However on the 82599 virtual function, the RXDCTL mechanism is not available. The driver attempts to work around this by using the SET_LPE mailbox method to lower the maximm frame size, but the ixgbe PF driver ignores this in order to keep the PF and all VFs in sync[0]. This means the PF will write up to the full 2K set in SRRCTL, causing it to write NET_SKB_PAD + NET_IP_ALIGN bytes past the end of the buffer. With 4K pages split into two buffers, this means it either writes NET_SKB_PAD + NET_IP_ALIGN bytes past the first buffer (and into the second), or NET_SKB_PAD + NET_IP_ALIGN bytes past the end of the DMA mapping. Avoid this by only enabling build_skb when using "large" buffers (3K). These are placed in each half of an order-1 page, preventing the PF from writing past the end of the mapping. [0]: Technically it only ever raises the max frame size, see ixgbe_set_vf_lpe() in ixgbe_sriov.c Fixes: f15c5ba5b6cd ("ixgbevf: add support for using order 1 pages to receive large frames") Signed-off-by: Samuel Mendoza-Jonas <samjonas@amazon.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-02-04netfilter: ctnetlink: disable helper autoassignFlorian Westphal2-2/+3
When userspace, e.g. conntrackd, inserts an entry with a specified helper, its possible that the helper is lost immediately after its added: ctnetlink_create_conntrack -> nf_ct_helper_ext_add + assign helper -> ctnetlink_setup_nat -> ctnetlink_parse_nat_setup -> parse_nat_setup -> nfnetlink_parse_nat_setup -> nf_nat_setup_info -> nf_conntrack_alter_reply -> __nf_ct_try_assign_helper ... and __nf_ct_try_assign_helper will zero the helper again. Set IPS_HELPER bit to bypass auto-assign logic, its unwanted, just like when helper is assigned via ruleset. Dropped old 'not strictly necessary' comment, it referred to use of rcu_assign_pointer() before it got replaced by RCU_INIT_POINTER(). NB: Fixes tag intentionally incorrect, this extends the referenced commit, but this change won't build without IPS_HELPER introduced there. Fixes: 6714cf5465d280 ("netfilter: nf_conntrack: fix explicit helper attachment and NAT") Reported-by: Pham Thanh Tuyen <phamtyn@gmail.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2022-02-04MAINTAINERS: netfilter: update git linksFlorian Westphal1-2/+2
nf and nf-next have a new location. Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2022-02-04netfilter: conntrack: re-init state for retransmitted syn-ackFlorian Westphal1-0/+12
TCP conntrack assumes that a syn-ack retransmit is identical to the previous syn-ack. This isn't correct and causes stuck 3whs in some more esoteric scenarios. tcpdump to illustrate the problem: client > server: Flags [S] seq 1365731894, win 29200, [mss 1460,sackOK,TS val 2083035583 ecr 0,wscale 7] server > client: Flags [S.] seq 145824453, ack 643160523, win 65535, [mss 8952,wscale 5,TS val 3215367629 ecr 2082921663] Note the invalid/outdated synack ack number. Conntrack marks this syn-ack as out-of-window/invalid, but it did initialize the reply direction parameters based on this packets content. client > server: Flags [S] seq 1365731894, win 29200, [mss 1460,sackOK,TS val 2083036623 ecr 0,wscale 7] ... retransmit... server > client: Flags [S.], seq 145824453, ack 643160523, win 65535, [mss 8952,wscale 5,TS val 3215368644 ecr 2082921663] and another bogus synack. This repeats, then client re-uses for a new attempt: client > server: Flags [S], seq 2375731741, win 29200, [mss 1460,sackOK,TS val 2083100223 ecr 0,wscale 7] server > client: Flags [S.], seq 145824453, ack 643160523, win 65535, [mss 8952,wscale 5,TS val 3215430754 ecr 2082921663] ... but still gets a invalid syn-ack. This repeats until: server > client: Flags [S.], seq 145824453, ack 643160523, win 65535, [mss 8952,wscale 5,TS val 3215437785 ecr 2082921663] server > client: Flags [R.], seq 145824454, ack 643160523, win 65535, [mss 8952,wscale 5,TS val 3215443451 ecr 2082921663] client > server: Flags [S], seq 2375731741, win 29200, [mss 1460,sackOK,TS val 2083115583 ecr 0,wscale 7] server > client: Flags [S.], seq 162602410, ack 2375731742, win 65535, [mss 8952,wscale 5,TS val 3215445754 ecr 2083115583] This syn-ack has the correct ack number, but conntrack flags it as invalid: The internal state was created from the first syn-ack seen so the sequence number of the syn-ack is treated as being outside of the announced window. Don't assume that retransmitted syn-ack is identical to previous one. Treat it like the first syn-ack and reinit state. Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2022-02-04netfilter: conntrack: move synack init code to helperFlorian Westphal1-18/+29
It seems more readable to use a common helper in the followup fix rather than copypaste or goto. No functional change intended. The function is only called for syn-ack or syn in repy direction in case of simultaneous open. Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2022-02-04netfilter: nft_payload: don't allow th access for fragmentsFlorian Westphal2-5/+6
Loads relative to ->thoff naturally expect that this points to the transport header, but this is only true if pkt->fragoff == 0. This has little effect for rulesets with connection tracking/nat because these enable ip defra. For other rulesets this prevents false matches. Fixes: 96518518cc41 ("netfilter: add nftables") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2022-02-04netfilter: conntrack: don't refresh sctp entries in closed stateFlorian Westphal1-0/+9
Vivek Thrivikraman reported: An SCTP server application which is accessed continuously by client application. When the session disconnects the client retries to establish a connection. After restart of SCTP server application the session is not established because of stale conntrack entry with connection state CLOSED as below. (removing this entry manually established new connection): sctp 9 CLOSED src=10.141.189.233 [..] [ASSURED] Just skip timeout update of closed entries, we don't want them to stay around forever. Reported-and-tested-by: Vivek Thrivikraman <vivek.thrivikraman@est.tech> Closes: https://bugzilla.netfilter.org/show_bug.cgi?id=1579 Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2022-02-03net: sparx5: Fix get_stat64 crash in tcpdumpSteen Hegelund1-1/+1
This problem was found with Sparx5 when the tcpdump tool requests the do_get_stats64 (sparx5_get_stats64) statistic. The portstats pointer was incorrectly incremented when fetching priority based statistics. Fixes: af4b11022e2d (net: sparx5: add ethtool configuration and statistics support) Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com> Link: https://lore.kernel.org/r/20220203102900.528987-1-steen.hegelund@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-03gcc-plugins/stackleak: Use noinstr in favor of notraceKees Cook1-3/+2
While the stackleak plugin was already using notrace, objtool is now a bit more picky. Update the notrace uses to noinstr. Silences the following objtool warnings when building with: CONFIG_DEBUG_ENTRY=y CONFIG_STACK_VALIDATION=y CONFIG_VMLINUX_VALIDATION=y CONFIG_GCC_PLUGIN_STACKLEAK=y vmlinux.o: warning: objtool: do_syscall_64()+0x9: call to stackleak_track_stack() leaves .noinstr.text section vmlinux.o: warning: objtool: do_int80_syscall_32()+0x9: call to stackleak_track_stack() leaves .noinstr.text section vmlinux.o: warning: objtool: exc_general_protection()+0x22: call to stackleak_track_stack() leaves .noinstr.text section vmlinux.o: warning: objtool: fixup_bad_iret()+0x20: call to stackleak_track_stack() leaves .noinstr.text section vmlinux.o: warning: objtool: do_machine_check()+0x27: call to stackleak_track_stack() leaves .noinstr.text section vmlinux.o: warning: objtool: .text+0x5346e: call to stackleak_erase() leaves .noinstr.text section vmlinux.o: warning: objtool: .entry.text+0x143: call to stackleak_erase() leaves .noinstr.text section vmlinux.o: warning: objtool: .entry.text+0x10eb: call to stackleak_erase() leaves .noinstr.text section vmlinux.o: warning: objtool: .entry.text+0x17f9: call to stackleak_erase() leaves .noinstr.text section Note that the plugin's addition of calls to stackleak_track_stack() from noinstr functions is expected to be safe, as it isn't runtime instrumentation and is self-contained. Cc: Alexander Popov <alex.popov@linux.com> Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-02-03Merge tag 'net-5.17-rc3' of ↵Linus Torvalds78-453/+877
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Including fixes from bpf, netfilter, and ieee802154. Current release - regressions: - Partially revert "net/smc: Add netlink net namespace support", fix uABI breakage - netfilter: - nft_ct: fix use after free when attaching zone template - nft_byteorder: track register operations Previous releases - regressions: - ipheth: fix EOVERFLOW in ipheth_rcvbulk_callback - phy: qca8081: fix speeds lower than 2.5Gb/s - sched: fix use-after-free in tc_new_tfilter() Previous releases - always broken: - tcp: fix mem under-charging with zerocopy sendmsg() - tcp: add missing tcp_skb_can_collapse() test in tcp_shift_skb_data() - neigh: do not trigger immediate probes on NUD_FAILED from neigh_managed_work, avoid a deadlock - bpf: use VM_MAP instead of VM_ALLOC for ringbuf, avoid KASAN false-positives - netfilter: nft_reject_bridge: fix for missing reply from prerouting - smc: forward wakeup to smc socket waitqueue after fallback - ieee802154: - return meaningful error codes from the netlink helpers - mcr20a: fix lifs/sifs periods - at86rf230, ca8210: stop leaking skbs on error paths - macsec: add missing un-offload call for NETDEV_UNREGISTER of parent - ax25: add refcount in ax25_dev to avoid UAF bugs - eth: mlx5e: - fix SFP module EEPROM query - fix broken SKB allocation in HW-GRO - IPsec offload: fix tunnel mode crypto for non-TCP/UDP flows - eth: amd-xgbe: - fix skb data length underflow - ensure reset of the tx_timer_active flag, avoid Tx timeouts - eth: stmmac: fix runtime pm use in stmmac_dvr_remove() - eth: e1000e: handshake with CSME starts from Alder Lake platforms" * tag 'net-5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (69 commits) ax25: fix reference count leaks of ax25_dev net: stmmac: ensure PTP time register reads are consistent net: ipa: request IPA register values be retained dt-bindings: net: qcom,ipa: add optional qcom,qmp property tools/resolve_btfids: Do not print any commands when building silently bpf: Use VM_MAP instead of VM_ALLOC for ringbuf net, neigh: Do not trigger immediate probes on NUD_FAILED from neigh_managed_work tcp: add missing tcp_skb_can_collapse() test in tcp_shift_skb_data() net: sparx5: do not refer to skb after passing it on Partially revert "net/smc: Add netlink net namespace support" net/mlx5e: Avoid field-overflowing memcpy() net/mlx5e: Use struct_group() for memcpy() region net/mlx5e: Avoid implicit modify hdr for decap drop rule net/mlx5e: IPsec: Fix tunnel mode crypto offload for non TCP/UDP traffic net/mlx5e: IPsec: Fix crypto offload for non TCP/UDP encapsulated traffic net/mlx5e: Don't treat small ceil values as unlimited in HTB offload net/mlx5: E-Switch, Fix uninitialized variable modact net/mlx5e: Fix handling of wrong devices during bond netevent net/mlx5e: Fix broken SKB allocation in HW-GRO net/mlx5e: Fix wrong calculation of header index in HW_GRO ...
2022-02-03Merge tag 'selinux-pr-20220203' of ↵Linus Torvalds1-1/+2
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux Pull selinux fix from Paul Moore: "One small SELinux patch to ensure that a policy structure field is properly reset after freeing so that we don't inadvertently do a double-free on certain error conditions" * tag 'selinux-pr-20220203' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux: selinux: fix double free of cond_list on error paths
2022-02-03Merge tag 'linux-kselftest-fixes-5.17-rc3' of ↵Linus Torvalds15-177/+209
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest Pull Kselftest fixes from Shuah Khan: "Important fixes to several tests and documentation clarification on running mainline kselftest on stable releases. A few notable fixes: - fix kselftest run hang due to child processes that haven't been terminated. Fix signals all child processes - fix false pass/fail results from vdso_test_abi, openat2, mincore - build failures when using -j (multiple jobs) option - exec test build failure due to incorrect build rule for a run-time created "pipe" - zram test fixes related to interaction with zram-generator to make sure zram test to coordinate deleted with zram-generator - zram test compression ratio calculation fix and skipping max_comp_streams. - increasing rtc test timeout - cpufreq test to write test results to stdout which will necessary on automated test systems" * tag 'linux-kselftest-fixes-5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: kselftest: Fix vdso_test_abi return status selftests: skip mincore.check_file_mmap when fs lacks needed support selftests: openat2: Skip testcases that fail with EOPNOTSUPP selftests: openat2: Add missing dependency in Makefile selftests: openat2: Print also errno in failure messages selftests: futex: Use variable MAKE instead of make selftests/exec: Remove pipe from TEST_GEN_FILES selftests/zram: Adapt the situation that /dev/zram0 is being used selftests/zram01.sh: Fix compression ratio calculation selftests/zram: Skip max_comp_streams interface on newer kernel docs/kselftest: clarify running mainline tests on stables kselftest: signal all child processes selftests: cpufreq: Write test output to stdout as well selftests: rtc: Increase test timeout so that all tests run
2022-02-03ax25: fix reference count leaks of ax25_devDuoming Zhou4-19/+41
The previous commit d01ffb9eee4a ("ax25: add refcount in ax25_dev to avoid UAF bugs") introduces refcount into ax25_dev, but there are reference leak paths in ax25_ctl_ioctl(), ax25_fwd_ioctl(), ax25_rt_add(), ax25_rt_del() and ax25_rt_opt(). This patch uses ax25_dev_put() and adjusts the position of ax25_addr_ax25dev() to fix reference cout leaks of ax25_dev. Fixes: d01ffb9eee4a ("ax25: add refcount in ax25_dev to avoid UAF bugs") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20220203150811.42256-1-duoming@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-03net: stmmac: ensure PTP time register reads are consistentYannick Vignon1-7/+12
Even if protected from preemption and interrupts, a small time window remains when the 2 register reads could return inconsistent values, each time the "seconds" register changes. This could lead to an about 1-second error in the reported time. Add logic to ensure the "seconds" and "nanoseconds" values are consistent. Fixes: 92ba6888510c ("stmmac: add the support for PTP hw clock driver") Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20220203160025.750632-1-yannick.vignon@oss.nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-03Merge https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfJakub Kicinski7-236/+11
Daniel Borkmann says: ==================== pull-request: bpf 2022-02-03 We've added 6 non-merge commits during the last 10 day(s) which contain a total of 7 files changed, 11 insertions(+), 236 deletions(-). The main changes are: 1) Fix BPF ringbuf to allocate its area with VM_MAP instead of VM_ALLOC flag which otherwise trips over KASAN, from Hou Tao. 2) Fix unresolved symbol warning in resolve_btfids due to LSM callback rename, from Alexei Starovoitov. 3) Fix a possible race in inc_misses_counter() when IRQ would trigger during counter update, from He Fengqing. 4) Fix tooling infra for cross-building with clang upon probing whether gcc provides the standard libraries, from Jean-Philippe Brucker. 5) Fix silent mode build for resolve_btfids, from Nathan Chancellor. 6) Drop unneeded and outdated lirc.h header copy from tooling infra as BPF does not require it anymore, from Sean Young. * https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf: tools/resolve_btfids: Do not print any commands when building silently bpf: Use VM_MAP instead of VM_ALLOC for ringbuf tools: Ignore errors from `which' when searching a GCC toolchain tools headers UAPI: remove stale lirc.h bpf: Fix possible race in inc_misses_counter bpf: Fix renaming task_getsecid_subj->current_getsecid_subj. ==================== Link: https://lore.kernel.org/r/20220203155815.25689-1-daniel@iogearbox.net Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-03printk: Fix incorrect __user type in proc_dointvec_minmax_sysadmin()Mickaël Salaün1-1/+1
The move of proc_dointvec_minmax_sysadmin() from kernel/sysctl.c to kernel/printk/sysctl.c introduced an incorrect __user attribute to the buffer argument. I spotted this change in [1] as well as the kernel test robot. Revert this change to please sparse: kernel/printk/sysctl.c:20:51: warning: incorrect type in argument 3 (different address spaces) kernel/printk/sysctl.c:20:51: expected void * kernel/printk/sysctl.c:20:51: got void [noderef] __user *buffer Fixes: faaa357a55e0 ("printk: move printk sysctl to printk/sysctl.c") Link: https://lore.kernel.org/r/20220104155024.48023-2-mic@digikod.net [1] Reported-by: kernel test robot <lkp@intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: John Ogness <john.ogness@linutronix.de> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Sergey Senozhatsky <senozhatsky@chromium.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Xiaoming Ni <nixiaoming@huawei.com> Signed-off-by: Mickaël Salaün <mic@linux.microsoft.com> Link: https://lore.kernel.org/r/20220203145029.272640-1-mic@digikod.net Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-02-03Revert "module, async: async_synchronize_full() on module init iff async is ↵Igor Pylypiv3-24/+5
used" This reverts commit 774a1221e862b343388347bac9b318767336b20b. We need to finish all async code before the module init sequence is done. In the reverted commit the PF_USED_ASYNC flag was added to mark a thread that called async_schedule(). Then the PF_USED_ASYNC flag was used to determine whether or not async_synchronize_full() needs to be invoked. This works when modprobe thread is calling async_schedule(), but it does not work if module dispatches init code to a worker thread which then calls async_schedule(). For example, PCI driver probing is invoked from a worker thread based on a node where device is attached: if (cpu < nr_cpu_ids) error = work_on_cpu(cpu, local_pci_probe, &ddi); else error = local_pci_probe(&ddi); We end up in a situation where a worker thread gets the PF_USED_ASYNC flag set instead of the modprobe thread. As a result, async_synchronize_full() is not invoked and modprobe completes without waiting for the async code to finish. The issue was discovered while loading the pm80xx driver: (scsi_mod.scan=async) modprobe pm80xx worker ... do_init_module() ... pci_call_probe() work_on_cpu(local_pci_probe) local_pci_probe() pm8001_pci_probe() scsi_scan_host() async_schedule() worker->flags |= PF_USED_ASYNC; ... < return from worker > ... if (current->flags & PF_USED_ASYNC) <--- false async_synchronize_full(); Commit 21c3c5d28007 ("block: don't request module during elevator init") fixed the deadlock issue which the reverted commit 774a1221e862 ("module, async: async_synchronize_full() on module init iff async is used") tried to fix. Since commit 0fdff3ec6d87 ("async, kmod: warn on synchronous request_module() from async workers") synchronous module loading from async is not allowed. Given that the original deadlock issue is fixed and it is no longer allowed to call synchronous request_module() from async we can remove PF_USED_ASYNC flag to make module init consistently invoke async_synchronize_full() unless async module probe is requested. Signed-off-by: Igor Pylypiv <ipylypiv@google.com> Reviewed-by: Changyuan Lyu <changyuanl@google.com> Reviewed-by: Luis Chamberlain <mcgrof@kernel.org> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-02-03Merge branch 'for-5.17-fixes' of ↵Linus Torvalds2-14/+65
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup Pull cgroup fixes from Tejun Heo: - Eric's fix for a long standing cgroup1 permission issue where it only checks for uid 0 instead of CAP which inadvertently allows unprivileged userns roots to modify release_agent userhelper - Fixes for the fallout from Waiman's recent cpuset work * 'for-5.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: cgroup/cpuset: Fix "suspicious RCU usage" lockdep warning cgroup-v1: Require capabilities to set release_agent cpuset: Fix the bug that subpart_cpus updated wrongly in update_cpumask() cgroup/cpuset: Make child cpusets restrict parents on v1 hierarchy
2022-02-03Merge branch 'net-ipa-enable-register-retention'Jakub Kicinski4-0/+70
Alex Elder says: ==================== net: ipa: enable register retention With runtime power management in place, we sometimes need to issue a command to enable retention of IPA register values before power collapse. This requires a new Device Tree property, whose presence will also be used to signal that the command is required. ==================== Link: https://lore.kernel.org/r/20220201150205.468403-1-elder@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-03net: ipa: request IPA register values be retainedAlex Elder3-0/+64
In some cases, the IPA hardware needs to request the always-on subsystem (AOSS) to coordinate with the IPA microcontroller to retain IPA register values at power collapse. This is done by issuing a QMP request to the AOSS microcontroller. A similar request ondoes that request. We must get and hold the "QMP" handle early, because we might get back EPROBE_DEFER for that. But the actual request should be sent while we know the IPA clock is active, and when we know the microcontroller is operational. Fixes: 1aac309d3207 ("net: ipa: use autosuspend") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-03dt-bindings: net: qcom,ipa: add optional qcom,qmp propertyAlex Elder1-0/+6
For some systems, the IPA driver must make a request to ensure that its registers are retained across power collapse of the IPA hardware. On such systems, we'll use the existence of the "qcom,qmp" property as a signal that this request is required. Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-03cgroup/cpuset: Fix "suspicious RCU usage" lockdep warningWaiman Long1-0/+10
It was found that a "suspicious RCU usage" lockdep warning was issued with the rcu_read_lock() call in update_sibling_cpumasks(). It is because the update_cpumasks_hier() function may sleep. So we have to release the RCU lock, call update_cpumasks_hier() and reacquire it afterward. Also add a percpu_rwsem_assert_held() in update_sibling_cpumasks() instead of stating that in the comment. Fixes: 4716909cc5c5 ("cpuset: Track cpusets that use parent's effective_cpus") Signed-off-by: Waiman Long <longman@redhat.com> Tested-by: Phil Auld <pauld@redhat.com> Reviewed-by: Phil Auld <pauld@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2022-02-03tools/resolve_btfids: Do not print any commands when building silentlyNathan Chancellor1-1/+5
When building with 'make -s', there is some output from resolve_btfids: $ make -sj"$(nproc)" oldconfig prepare MKDIR .../tools/bpf/resolve_btfids/libbpf/ MKDIR .../tools/bpf/resolve_btfids//libsubcmd LINK resolve_btfids Silent mode means that no information should be emitted about what is currently being done. Use the $(silent) variable from Makefile.include to avoid defining the msg macro so that there is no information printed. Fixes: fbbb68de80a4 ("bpf: Add resolve_btfids tool to resolve BTF IDs in ELF object") Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220201212503.731732-1-nathan@kernel.org
2022-02-03Revert "mm/gup: small refactoring: simplify try_grab_page()"John Hubbard1-5/+30
This reverts commit 54d516b1d62ff8f17cee2da06e5e4706a0d00b8a That commit did a refactoring that effectively combined fast and slow gup paths (again). And that was again incorrect, for two reasons: a) Fast gup and slow gup get reference counts on pages in different ways and with different goals: see Linus' writeup in commit cd1adf1b63a1 ("Revert "mm/gup: remove try_get_page(), call try_get_compound_head() directly""), and b) try_grab_compound_head() also has a specific check for "FOLL_LONGTERM && !is_pinned(page)", that assumes that the caller can fall back to slow gup. This resulted in new failures, as recently report by Will McVicker [1]. But (a) has problems too, even though they may not have been reported yet. So just revert this. Link: https://lore.kernel.org/r/20220131203504.3458775-1-willmcvicker@google.com [1] Fixes: 54d516b1d62f ("mm/gup: small refactoring: simplify try_grab_page()") Reported-and-tested-by: Will McVicker <willmcvicker@google.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Minchan Kim <minchan@google.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Heiko Carstens <hca@linux.ibm.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: stable@vger.kernel.org # 5.15 Signed-off-by: John Hubbard <jhubbard@nvidia.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-08-12 17:26:47 +0000