Age | Commit message (Collapse) | Author | Files | Lines |
|
The bdi congestion tracking in not widely used and will be removed.
Fuse is one of a small number of filesystems that uses it, setting both
the sync (read) and async (write) congestion flags at what it determines
are appropriate times.
The only remaining effect of the sync flag is to cause read-ahead to be
skipped. The only remaining effect of the async flag is to cause (some)
WB_SYNC_NONE writes to be skipped.
So instead of setting the flags, change:
- .readahead to stop when it has submitted all non-async pages for
read.
- .writepages to do nothing if WB_SYNC_NONE and the flag would be set
- .writepage to return AOP_WRITEPAGE_ACTIVATE if WB_SYNC_NONE and the
flag would be set.
The writepages change causes a behavioural change in that pageout() can
now return PAGE_ACTIVATE instead of PAGE_KEEP, so SetPageActive() will be
called on the page which (I think) will further delay the next attempt at
writeout. This might be a good thing.
Link: https://lkml.kernel.org/r/164549983737.9187.2627117501000365074.stgit@noble.brown
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Anna Schumaker <Anna.Schumaker@Netapp.com>
Cc: Chao Yu <chao@kernel.org>
Cc: Darrick J. Wong <djwong@kernel.org>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Jaegeuk Kim <jaegeuk@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jeff Layton <jlayton@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Paolo Valente <paolo.valente@linaro.org>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If ->readpages doesn't process all the pages, then it is best to act as
though they weren't requested so that a subsequent readahead can try
again.
So:
- remove any 'ahead' pages from the page cache so they can be loaded
with ->readahead() rather then multiple ->read()s
- update the file_ra_state to reflect the reads that were actually
submitted.
This allows ->readpages() to abort early due e.g. to congestion, which
will then allow us to remove the inode_read_congested() test from
page_Cache_async_ra().
Link: https://lkml.kernel.org/r/164549983736.9187.16755913785880819183.stgit@noble.brown
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Anna Schumaker <Anna.Schumaker@Netapp.com>
Cc: Chao Yu <chao@kernel.org>
Cc: Darrick J. Wong <djwong@kernel.org>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Jaegeuk Kim <jaegeuk@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jeff Layton <jlayton@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Paolo Valente <paolo.valente@linaro.org>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add some "big-picture" documentation for read-ahead and polish the code
to make it fit this documentation.
The meaning of ->async_size is clarified to match its name. i.e. Any
request to ->readahead() has a sync part and an async part. The caller
will wait for the sync pages to complete, but will not wait for the
async pages. The first async page is still marked PG_readahead
Note that the current function names page_cache_sync_ra() and
page_cache_async_ra() are misleading. All ra request are partly sync
and partly async, so either part can be empty. A page_cache_sync_ra()
request will usually set ->async_size non-zero, implying it is not all
synchronous.
When a non-zero req_count is passed to page_cache_async_ra(), the
implication is that some prefix of the request is synchronous, though
the calculation made there is incorrect - I haven't tried to fix it.
Link: https://lkml.kernel.org/r/164549983734.9187.11586890887006601405.stgit@noble.brown
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Anna Schumaker <Anna.Schumaker@Netapp.com>
Cc: Chao Yu <chao@kernel.org>
Cc: Darrick J. Wong <djwong@kernel.org>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Jaegeuk Kim <jaegeuk@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jeff Layton <jlayton@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Paolo Valente <paolo.valente@linaro.org>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "Remove remaining parts of congestion tracking code", v2.
This patch (of 11):
Various DOC: sections in gfp.h have subsection headers (~~~) but the
place where they are included in mm-api.rst does not have section, only
chapters.
So convert to section headers (---) to avoid confusion. Specifically if
sections are added later in mm-api.rst, an error results.
Link: https://lkml.kernel.org/r/164549971112.9187.16871723439770288255.stgit@noble.brown
Link: https://lkml.kernel.org/r/164549983733.9187.17894407453436115822.stgit@noble.brown
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Jan Kara <jack@suse.cz>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Jaegeuk Kim <jaegeuk@kernel.org>
Cc: Chao Yu <chao@kernel.org>
Cc: Jeff Layton <jlayton@kernel.org>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Anna Schumaker <Anna.Schumaker@Netapp.com>
Cc: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: Darrick J. Wong <djwong@kernel.org>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Paolo Valente <paolo.valente@linaro.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
inode->i_mutex has been replaced with inode->i_rwsem long ago. Fix
comments still mentioning i_mutex.
Link: https://lkml.kernel.org/r/20220214031314.100094-1-hongnan.li@linux.alibaba.com
Signed-off-by: hongnanli <hongnan.li@linux.alibaba.com>
Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Simply return directly instead of assign the return value to another
variable.
Link: https://lkml.kernel.org/r/20220114021641.13927-1-joseph.qi@linux.alibaba.com
Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Reported-by: Zeal Robot <zealci@zte.com.cn>
Cc: Minghao Chi <chi.minghao@zte.com.cn>
Cc: CGEL ZTE <cgel.zte@gmail.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ntfs_read_inode_mount invokes ntfs_malloc_nofs with zero allocation
size. It triggers one BUG in the __ntfs_malloc function.
Fix this by adding sanity check on ni->attr_list_size.
Link: https://lkml.kernel.org/r/20220120094914.47736-1-dzm91@hust.edu.cn
Reported-by: syzbot+3c765c5248797356edaa@syzkaller.appspotmail.com
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Acked-by: Anton Altaparmakov <anton@tuxera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some of the more common spelling mistakes and typos that I've found
while fixing up spelling mistakes in the kernel in the past four months.
Link: https://lkml.kernel.org/r/20220216152343.105546-1-colin.i.king@gmail.com
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Ever since these macros were introduced in commit b56c0d8937e6
("kthread: implement kthread_worker"), there has been precisely one user
(commit 4d115420707a, "NVMe: Async IO queue deletion"), and that user
went away in 2016 with db3cbfff5bcc ("NVMe: IO queue deletion
re-write").
Apart from being unused, these macros are also awkward to use (which may
contribute to them not being used): Having a way to statically (or
on-stack) allocating the storage for the struct kthread_worker itself
doesn't help much, since obviously one needs to have some code for
actually _spawning_ the worker thread, which must have error checking.
And these days we have the kthread_create_worker() interface which both
allocates the struct kthread_worker and spawns the kthread.
Link: https://lkml.kernel.org/r/20220314145343.494694-1-linux@rasmusvillemoes.dk
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Yafang Shao <laoar.shao@gmail.com>
Cc: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull kvm fix from Paolo Bonzini:
"Fix for the SLS mitigation, which makes a 'SETcc/RET' pair grow
to 'SETcc/RET/INT3'.
This doesn't fit in 4 bytes any more, so the alignment has to
change to 8 for this case"
* tag 'for-linus-5.17' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm/emulate: Fix SETcc emulation function offsets with SLS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Two driver fixes:
- a fix for zinitix touchscreen to properly report contacts
- a fix for aiptek tablet driver to be more resilient to devices with
incorrect descriptors"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: aiptek - properly check endpoint type
Input: zinitix - do not report shadow fingers
|
|
The commit in Fixes started adding INT3 after RETs as a mitigation
against straight-line speculation.
The fastop SETcc implementation in kvm's insn emulator uses macro magic
to generate all possible SETcc functions and to jump to them when
emulating the respective instruction.
However, it hardcodes the size and alignment of those functions to 4: a
three-byte SETcc insn and a single-byte RET. BUT, with SLS, there's an
INT3 that gets slapped after the RET, which brings the whole scheme out
of alignment:
15: 0f 90 c0 seto %al
18: c3 ret
19: cc int3
1a: 0f 1f 00 nopl (%rax)
1d: 0f 91 c0 setno %al
20: c3 ret
21: cc int3
22: 0f 1f 00 nopl (%rax)
25: 0f 92 c0 setb %al
28: c3 ret
29: cc int3
and this explodes like this:
int3: 0000 [#1] PREEMPT SMP PTI
CPU: 0 PID: 2435 Comm: qemu-system-x86 Not tainted 5.17.0-rc8-sls #1
Hardware name: Dell Inc. Precision WorkStation T3400 /0TP412, BIOS A14 04/30/2012
RIP: 0010:setc+0x5/0x8 [kvm]
Code: 00 00 0f 1f 00 0f b6 05 43 24 06 00 c3 cc 0f 1f 80 00 00 00 00 0f 90 c0 c3 cc 0f \
1f 00 0f 91 c0 c3 cc 0f 1f 00 0f 92 c0 c3 cc <0f> 1f 00 0f 93 c0 c3 cc 0f 1f 00 \
0f 94 c0 c3 cc 0f 1f 00 0f 95 c0
Call Trace:
<TASK>
? x86_emulate_insn [kvm]
? x86_emulate_instruction [kvm]
? vmx_handle_exit [kvm_intel]
? kvm_arch_vcpu_ioctl_run [kvm]
? kvm_vcpu_ioctl [kvm]
? __x64_sys_ioctl
? do_syscall_64
? entry_SYSCALL_64_after_hwframe
</TASK>
Raise the alignment value when SLS is enabled and use a macro for that
instead of hard-coding naked numbers.
Fixes: e463a09af2f0 ("x86: Add straight-line-speculation mitigation")
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Jamie Heilman <jamie@audible.transient.net>
Link: https://lore.kernel.org/r/YjGzJwjrvxg5YZ0Z@audible.transient.net
[Add a comment and a bit of safety checking, since this is going to be changed
again for IBT support. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fix from Arnd Bergmann:
"Here is one last regression fix for 5.17, reverting a patch that went
into 5.16 as a cleanup that ended up breaking external interrupts on
Layerscape chips.
The revert makes it work again, but also reintroduces a build time
warning about the nonstandard DT binding that will have to be dealt
with in the future"
* tag 'soc-fixes-5.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
Revert "arm64: dts: freescale: Fix 'interrupt-map' parent address cells"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small(ish) fixes, both in drivers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fnic: Finish scsi_cmnd before dropping the spinlock
scsi: mpt3sas: Page fault in reply q processing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Avoid iterating empty evlist, fixing a segfault with 'perf stat --null'
- Ignore case in topdown.slots check, fixing issue with Intel Icelake
JSON metrics.
- Fix symbol size calculation condition for fixing up corner case
symbol end address obtained from Kallsyms.
* tag 'perf-tools-fixes-for-v5.17-2022-03-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf parse-events: Ignore case in topdown.slots check
perf evlist: Avoid iteration for empty evlist.
perf symbols: Fix symbol size calculation condition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fix from Greg KH:
"Here is a single driver fix for 5.17-final that has been submitted
many times but I somehow missed it in my patch queue:
- fix for counter sysfs code for reported problem
This has been in linux-next all week with no reported issues"
* tag 'char-misc-5.17-final' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
counter: Stop using dev_get_drvdata() to get the counter device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small remaining USB fixes for 5.17-final.
They include:
- two USB gadget driver fixes for reported problems
- usbtmc driver fix for syzbot found issues
- musb patch partial revert to resolve a reported regression.
All of these have been in linux-next this week with no reported
problems"
* tag 'usb-5.17-final' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: Fix use-after-free bug by not setting udc->dev.driver
usb: usbtmc: Fix bug in pipe direction for control transfers
partially Revert "usb: musb: Set the DT node on the child device"
usb: gadget: rndis: prevent integer overflow in rndis_set_response()
|
|
An issue with icelakex metrics:
https://git.kernel.org/pub/scm/linux/kernel/git/acme/linux.git/tree/tools/perf/pmu-events/arch/x86/icelakex/icx-metrics.json?h=perf/core&id=65eab2bc7dab326ee892ec5a4c749470b368b51a#n48
That causes the slots not to be first.
Fixes: 94dbfd6781a0e87b ("perf parse-events: Architecture specific leader override")
Reported-by: Caleb Biggers <caleb.biggers@intel.com>
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Link: https://lore.kernel.org/r/20220317224309.543736-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
As seen with 'perf stat --null ..' and reported in:
https://lore.kernel.org/lkml/YjCLcpcX2peeQVCH@kernel.org/
v2. Avoids setting evsel in the empty list case as suggested by Jiri Olsa.
Committer testing:
Before:
$ perf stat --null sleep 1
Segmentation fault (core dumped)
$
After:
$ perf stat --null sleep 1
Performance counter stats for 'sleep 1':
1.010340646 seconds time elapsed
0.001420000 seconds user
0.000000000 seconds sys
$
Fixes: 472832d2c000b961 ("perf evlist: Refactor evlist__for_each_cpu()")
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20220317231643.550902-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Before this patch, the symbol end address fixup to be called, needed two
conditions being met:
if (prev->end == prev->start && prev->end != curr->start)
Where
"prev->end == prev->start" means that prev is zero-long
(and thus needs a fixup)
and
"prev->end != curr->start" means that fixup hasn't been applied yet
However, this logic is incorrect in the following situation:
*curr = {rb_node = {__rb_parent_color = 278218928,
rb_right = 0x0, rb_left = 0x0},
start = 0xc000000000062354,
end = 0xc000000000062354, namelen = 40, type = 2 '\002',
binding = 0 '\000', idle = 0 '\000', ignore = 0 '\000',
inlined = 0 '\000', arch_sym = 0 '\000', annotate2 = false,
name = 0x1159739e "kprobe_optinsn_page\t[__builtin__kprobes]"}
*prev = {rb_node = {__rb_parent_color = 278219041,
rb_right = 0x109548b0, rb_left = 0x109547c0},
start = 0xc000000000062354,
end = 0xc000000000062354, namelen = 12, type = 2 '\002',
binding = 1 '\001', idle = 0 '\000', ignore = 0 '\000',
inlined = 0 '\000', arch_sym = 0 '\000', annotate2 = false,
name = 0x1095486e "optinsn_slot"}
In this case, prev->start == prev->end == curr->start == curr->end,
thus the condition above thinks that "we need a fixup due to zero
length of prev symbol, but it has been probably done, since the
prev->end == curr->start", which is wrong.
After the patch, the execution path proceeds to arch__symbols__fixup_end
function which fixes up the size of prev symbol by adding page_size to
its end offset.
Fixes: 3b01a413c196c910 ("perf symbols: Improve kallsyms symbol end addr calculation")
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: http://lore.kernel.org/lkml/20220317135536.805-1-mpetlan@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"Fix two compiler warnings introduced by recent commits: pointer
arithmetic and double initialisation of struct field"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: errata: avoid duplicate field initializer
arm64: fix clang warning about TRAMP_VALIAS
|
|
Pull cifs fix from Steve French:
"Small fix for regression in multiuser mounts.
The additional improvements suggested by Ronnie to make the server and
session status handling code easier to read can wait for the 5.18
merge window."
* tag '5.17-rc8-smb3-fix' of git://git.samba.org/sfrench/cifs-2.6:
smb3: fix incorrect session setup check for multiuser mounts
|
|
Pull block fixes from Jens Axboe:
- Revert of a nvme target feature (Hannes)
- Fix a memory leak with rq-qos (Ming)
* tag 'block-5.17-2022-03-18' of git://git.kernel.dk/linux-block:
nvmet: revert "nvmet: make discovery NQN configurable"
block: release rq qos structures for queue without disk
|
|
Pull drm fixes from Dave Airlie:
"A few minor changes to finish things off, one mgag200 regression, imx
fix and couple of panel changes.
imx:
- Don't test bus flags in atomic check
mgag200:
- Fix PLL setup on some models
panel:
- Fix bpp settings on Innolux G070Y2-L01
- Fix DRM_PANEL_EDP Kconfig dependencies"
* tag 'drm-fixes-2022-03-18' of git://anongit.freedesktop.org/drm/drm:
drm: Don't make DRM_PANEL_BRIDGE dependent on DRM_KMS_HELPERS
drm/panel: simple: Fix Innolux G070Y2-L01 BPP settings
drm/imx: parallel-display: Remove bus flags check in imx_pd_bridge_atomic_check()
drm/mgag200: Fix PLL setup for g200wb and g200ew
|
|
The '.type' field is initialized both in place and in the macro
as reported by this W=1 warning:
arch/arm64/include/asm/cpufeature.h:281:9: error: initialized field overwritten [-Werror=override-init]
281 | (ARM64_CPUCAP_SCOPE_LOCAL_CPU | ARM64_CPUCAP_OPTIONAL_FOR_LATE_CPU)
| ^
arch/arm64/kernel/cpu_errata.c:136:17: note: in expansion of macro 'ARM64_CPUCAP_LOCAL_CPU_ERRATUM'
136 | .type = ARM64_CPUCAP_LOCAL_CPU_ERRATUM, \
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/arm64/kernel/cpu_errata.c:145:9: note: in expansion of macro 'ERRATA_MIDR_RANGE'
145 | ERRATA_MIDR_RANGE(m, var, r_min, var, r_max)
| ^~~~~~~~~~~~~~~~~
arch/arm64/kernel/cpu_errata.c:613:17: note: in expansion of macro 'ERRATA_MIDR_REV_RANGE'
613 | ERRATA_MIDR_REV_RANGE(MIDR_CORTEX_A510, 0, 0, 2),
| ^~~~~~~~~~~~~~~~~~~~~
arch/arm64/include/asm/cpufeature.h:281:9: note: (near initialization for 'arm64_errata[18].type')
281 | (ARM64_CPUCAP_SCOPE_LOCAL_CPU | ARM64_CPUCAP_OPTIONAL_FOR_LATE_CPU)
| ^
Remove the extranous initializer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 1dd498e5e26a ("KVM: arm64: Workaround Cortex-A510's single-step and PAC trap errata")
Link: https://lore.kernel.org/r/20220316183800.1546731-1-arnd@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The newly introduced TRAMP_VALIAS definition causes a build warning
with clang-14:
arch/arm64/include/asm/vectors.h:66:31: error: arithmetic on a null pointer treated as a cast from integer to pointer is a GNU extension [-Werror,-Wnull-pointer-arithmetic]
return (char *)TRAMP_VALIAS + SZ_2K * slot;
Change the addition to something clang does not complain about.
Fixes: bd09128d16fa ("arm64: Add percpu vectors for EL1")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Morse <james.morse@arm.com>
Link: https://lore.kernel.org/r/20220316183833.1563139-1-arnd@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
* drm/imx: Don't test bus flags in atomic check
* drm/mgag200: Fix PLL setup on some models
* drm/panel: Fix bpp settings on Innolux G070Y2-L01; Fix DRM_PANEL_EDP
Kconfig dependencies
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/YjMNcqOuDFDoe+EN@linux-uq9g
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, ipsec, and wireless.
A few last minute revert / disable and fix patches came down from our
sub-trees. We're not waiting for any fixes at this point.
Current release - regressions:
- Revert "netfilter: nat: force port remap to prevent shadowing
well-known ports", restore working conntrack on asymmetric paths
- Revert "ath10k: drop beacon and probe response which leak from
other channel", restore working AP and mesh mode on QCA9984
- eth: intel: fix hang during reboot/shutdown
Current release - new code bugs:
- netfilter: nf_tables: disable register tracking, it needs more work
to cover all corner cases
Previous releases - regressions:
- ipv6: fix skb_over_panic in __ip6_append_data when (admin-only)
extension headers get specified
- esp6: fix ESP over TCP/UDP, interpret ipv6_skip_exthdr's return
value more selectively
- bnx2x: fix driver load failure when FW not present in initrd
Previous releases - always broken:
- vsock: stop destroying unrelated sockets in nested virtualization
- packet: fix slab-out-of-bounds access in packet_recvmsg()
Misc:
- add Paolo Abeni to networking maintainers!"
* tag 'net-5.17-final' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (26 commits)
iavf: Fix hang during reboot/shutdown
net: mscc: ocelot: fix backwards compatibility with single-chain tc-flower offload
net: bcmgenet: skip invalid partial checksums
bnx2x: fix built-in kernel driver load failure
net: phy: mscc: Add MODULE_FIRMWARE macros
net: dsa: Add missing of_node_put() in dsa_port_parse_of
net: handle ARPHRD_PIMREG in dev_is_mac_header_xmit()
Revert "ath10k: drop beacon and probe response which leak from other channel"
hv_netvsc: Add check for kvmalloc_array
iavf: Fix double free in iavf_reset_task
ice: destroy flow director filter mutex after releasing VSIs
ice: fix NULL pointer dereference in ice_update_vsi_tx_ring_stats()
Add Paolo Abeni to networking maintainers
atm: eni: Add check for dma_map_single
net/packet: fix slab-out-of-bounds access in packet_recvmsg()
net: mdio: mscc-miim: fix duplicate debugfs entry
net: phy: marvell: Fix invalid comparison in the resume and suspend functions
esp6: fix check on ipv6_skip_exthdr's return value
net: dsa: microchip: add spi_device_id tables
netfilter: nf_tables: disable register tracking
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Revert recent commit that caused multiple systems to misbehave due to
firmware issues"
* tag 'acpi-5.17-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI: scan: Do not add device IDs from _CID if _HID is not valid"
|
|
Merge misc fixes from Andrew Morton:
"Four patches.
Subsystems affected by this patch series: mm/swap, kconfig, ocfs2, and
selftests"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
selftests: vm: fix clang build error multiple output files
ocfs2: fix crash when initialize filecheck kobj fails
configs/debug: restore DEBUG_INFO=y for overriding
mm: swap: get rid of livelock in swapin readahead
|
|
When building the vm selftests using clang, some errors are seen due to
having headers in the compilation command:
clang -Wall -I ../../../../usr/include -no-pie gup_test.c ../../../../mm/gup_test.h -lrt -lpthread -o .../tools/testing/selftests/vm/gup_test
clang: error: cannot specify -o when generating multiple output files
make[1]: *** [../lib.mk:146: .../tools/testing/selftests/vm/gup_test] Error 1
Rework to add the header files to LOCAL_HDRS before including ../lib.mk,
since the dependency is evaluated in '$(OUTPUT)/%:%.c $(LOCAL_HDRS)' in
file lib.mk.
Link: https://lkml.kernel.org/r/20220304000645.1888133-1-yosryahmed@google.com
Signed-off-by: Yosry Ahmed <yosryahmed@google.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Once s_root is set, genric_shutdown_super() will be called if
fill_super() fails. That means, we will call ocfs2_dismount_volume()
twice in such case, which can lead to kernel crash.
Fix this issue by initializing filecheck kobj before setting s_root.
Link: https://lkml.kernel.org/r/20220310081930.86305-1-joseph.qi@linux.alibaba.com
Fixes: 5f483c4abb50 ("ocfs2: add kobject for online file check")
Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Previously, I failed to realize that Kees' patch [1] has not been merged
into the mainline yet, and dropped DEBUG_INFO=y too eagerly from the
mainline. As the results, "make debug.config" won't be able to flip
DEBUG_INFO=n from the existing .config. This should close the gaps of a
few weeks before Kees' patch is there, and work regardless of their
merging status anyway.
Link: https://lore.kernel.org/all/20220125075126.891825-1-keescook@chromium.org/ [1]
Link: https://lkml.kernel.org/r/20220308153524.8618-1-quic_qiancai@quicinc.com
Signed-off-by: Qian Cai <quic_qiancai@quicinc.com>
Reported-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In our testing, a livelock task was found. Through sysrq printing, same
stack was found every time, as follows:
__swap_duplicate+0x58/0x1a0
swapcache_prepare+0x24/0x30
__read_swap_cache_async+0xac/0x220
read_swap_cache_async+0x58/0xa0
swapin_readahead+0x24c/0x628
do_swap_page+0x374/0x8a0
__handle_mm_fault+0x598/0xd60
handle_mm_fault+0x114/0x200
do_page_fault+0x148/0x4d0
do_translation_fault+0xb0/0xd4
do_mem_abort+0x50/0xb0
The reason for the livelock is that swapcache_prepare() always returns
EEXIST, indicating that SWAP_HAS_CACHE has not been cleared, so that it
cannot jump out of the loop. We suspect that the task that clears the
SWAP_HAS_CACHE flag never gets a chance to run. We try to lower the
priority of the task stuck in a livelock so that the task that clears
the SWAP_HAS_CACHE flag will run. The results show that the system
returns to normal after the priority is lowered.
In our testing, multiple real-time tasks are bound to the same core, and
the task in the livelock is the highest priority task of the core, so
the livelocked task cannot be preempted.
Although cond_resched() is used by __read_swap_cache_async, it is an
empty function in the preemptive system and cannot achieve the purpose
of releasing the CPU. A high-priority task cannot release the CPU
unless preempted by a higher-priority task. But when this task is
already the highest priority task on this core, other tasks will not be
able to be scheduled. So we think we should replace cond_resched() with
schedule_timeout_uninterruptible(1), schedule_timeout_interruptible will
call set_current_state first to set the task state, so the task will be
removed from the running queue, so as to achieve the purpose of giving
up the CPU and prevent it from running in kernel mode for too long.
(akpm: ugly hack becomes uglier. But it fixes the issue in a
backportable-to-stable fashion while we hopefully work on something
better)
Link: https://lkml.kernel.org/r/20220221111749.1928222-1-cgel.zte@gmail.com
Signed-off-by: Guo Ziliang <guo.ziliang@zte.com.cn>
Reported-by: Zeal Robot <zealci@zte.com.cn>
Reviewed-by: Ran Xiaokai <ran.xiaokai@zte.com.cn>
Reviewed-by: Jiang Xuexin <jiang.xuexin@zte.com.cn>
Reviewed-by: Yang Yang <yang.yang29@zte.com.cn>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Roger Quadros <rogerq@kernel.org>
Cc: Ziliang Guo <guo.ziliang@zte.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Recent commit 974578017fc1 ("iavf: Add waiting so the port is
initialized in remove") adds a wait-loop at the beginning of
iavf_remove() to ensure that port initialization is finished
prior unregistering net device. This causes a regression
in reboot/shutdown scenario because in this case callback
iavf_shutdown() is called and this callback detaches the device,
makes it down if it is running and sets its state to __IAVF_REMOVE.
Later shutdown callback of associated PF driver (e.g. ice_shutdown)
is called. That callback calls among other things sriov_disable()
that calls indirectly iavf_remove() (see stack trace below).
As the adapter state is already __IAVF_REMOVE then the mentioned
loop is end-less and shutdown process hangs.
The patch fixes this by checking adapter's state at the beginning
of iavf_remove() and skips the rest of the function if the adapter
is already in remove state (shutdown is in progress).
Reproducer:
1. Create VF on PF driven by ice or i40e driver
2. Ensure that the VF is bound to iavf driver
3. Reboot
[52625.981294] sysrq: SysRq : Show Blocked State
[52625.988377] task:reboot state:D stack: 0 pid:17359 ppid: 1 f2
[52625.996732] Call Trace:
[52625.999187] __schedule+0x2d1/0x830
[52626.007400] schedule+0x35/0xa0
[52626.010545] schedule_hrtimeout_range_clock+0x83/0x100
[52626.020046] usleep_range+0x5b/0x80
[52626.023540] iavf_remove+0x63/0x5b0 [iavf]
[52626.027645] pci_device_remove+0x3b/0xc0
[52626.031572] device_release_driver_internal+0x103/0x1f0
[52626.036805] pci_stop_bus_device+0x72/0xa0
[52626.040904] pci_stop_and_remove_bus_device+0xe/0x20
[52626.045870] pci_iov_remove_virtfn+0xba/0x120
[52626.050232] sriov_disable+0x2f/0xe0
[52626.053813] ice_free_vfs+0x7c/0x340 [ice]
[52626.057946] ice_remove+0x220/0x240 [ice]
[52626.061967] ice_shutdown+0x16/0x50 [ice]
[52626.065987] pci_device_shutdown+0x34/0x60
[52626.070086] device_shutdown+0x165/0x1c5
[52626.074011] kernel_restart+0xe/0x30
[52626.077593] __do_sys_reboot+0x1d2/0x210
[52626.093815] do_syscall_64+0x5b/0x1a0
[52626.097483] entry_SYSCALL_64_after_hwframe+0x65/0xca
Fixes: 974578017fc1 ("iavf: Add waiting so the port is initialized in remove")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://lore.kernel.org/r/20220317104524.2802848-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
offload
ACL rules can be offloaded to VCAP IS2 either through chain 0, or, since
the blamed commit, through a chain index whose number encodes a specific
PAG (Policy Action Group) and lookup number.
The chain number is translated through ocelot_chain_to_pag() into a PAG,
and through ocelot_chain_to_lookup() into a lookup number.
The problem with the blamed commit is that the above 2 functions don't
have special treatment for chain 0. So ocelot_chain_to_pag(0) returns
filter->pag = 224, which is in fact -32, but the "pag" field is an u8.
So we end up programming the hardware with VCAP IS2 entries having a PAG
of 224. But the way in which the PAG works is that it defines a subset
of VCAP IS2 filters which should match on a packet. The default PAG is
0, and previous VCAP IS1 rules (which we offload using 'goto') can
modify it. So basically, we are installing filters with a PAG on which
no packet will ever match. This is the hardware equivalent of adding
filters to a chain which has no 'goto' to it.
Restore the previous functionality by making ACL filters offloaded to
chain 0 go to PAG 0 and lookup number 0. The choice of PAG is clearly
correct, but the choice of lookup number isn't "as before" (which was to
leave the lookup a "don't care"). However, lookup 0 should be fine,
since even though there are ACL actions (policers) which have a
requirement to be used in a specific lookup, that lookup is 0.
Fixes: 226e9cd82a96 ("net: mscc: ocelot: only install TCAM entries into a specific lookup and PAG")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220316192117.2568261-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RXCHK block will return a partial checksum of 0 if it encounters
a problem while receiving a packet. Since a 1's complement sum can
only produce this result if no bits are set in the received data
stream it is fair to treat it as an invalid partial checksum and
not pass it up the stack.
Fixes: 810155397890 ("net: bcmgenet: use CHECKSUM_COMPLETE for NETIF_F_RXCSUM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220317012812.1313196-1-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
added request_firmware() logic in probe() which caused
load failure when firmware file is not present in initrd (below),
as access to firmware file is not feasible during probe.
Direct firmware load for bnx2x/bnx2x-e2-7.13.15.0.fw failed with error -2
Direct firmware load for bnx2x/bnx2x-e2-7.13.21.0.fw failed with error -2
This patch fixes this issue by -
1. Removing request_firmware() logic from the probe()
such that .ndo_open() handle it as it used to handle
it earlier
2. Given request_firmware() is removed from probe(), so
driver has to relax FW version comparisons a bit against
the already loaded FW version (by some other PFs of same
adapter) to allow different compatible/close enough FWs with which
multiple PFs may run with (in different environments), as the
given PF who is in probe flow has no idea now with which firmware
file version it is going to initialize the device in ndo_open()
Link: https://lore.kernel.org/all/46f2d9d9-ae7f-b332-ddeb-b59802be2bab@molgen.mpg.de/
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220316214613.6884-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver requires firmware so define MODULE_FIRMWARE so that modinfo
provides the details.
Fixes: fa164e40c53b ("net: phy: mscc: split the driver into separate files")
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Link: https://lore.kernel.org/r/20220316151835.88765-1-juergh@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: 6d4e5c570c2d ("net: dsa: get port type at parse time")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220316082602.10785-1-linmq006@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Fix a number of undefined references to drm_kms_helper.ko in
drm_dp_helper.ko:
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_mst_duplicate_state':
drm_dp_mst_topology.c:(.text+0x2df0): undefined reference to `__drm_atomic_helper_private_obj_duplicate_state'
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_delayed_destroy_work':
drm_dp_mst_topology.c:(.text+0x370c): undefined reference to `drm_kms_helper_hotplug_event'
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_mst_up_req_work':
drm_dp_mst_topology.c:(.text+0x7938): undefined reference to `drm_kms_helper_hotplug_event'
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_mst_link_probe_work':
drm_dp_mst_topology.c:(.text+0x82e0): undefined reference to `drm_kms_helper_hotplug_event'
This happens if panel-edp.ko has been configured with
DRM_PANEL_EDP=y
DRM_DP_HELPER=y
DRM_KMS_HELPER=m
which builds DP helpers into the kernel and KMS helpers sa a module.
Making DRM_PANEL_EDP select DRM_KMS_HELPER resolves this problem.
To avoid a resulting cyclic dependency with DRM_PANEL_BRIDGE, don't
make the latter depend on DRM_KMS_HELPER and fix the one DRM bridge
drivers that doesn't already select DRM_KMS_HELPER. As KMS helpers
cannot be selected directly by the user, config symbols should avoid
depending on it anyway.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 3755d35ee1d2 ("drm/panel: Select DRM_DP_HELPER for DRM_PANEL_EDP")
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Brian Masney <bmasney@redhat.com>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Linux Kernel Functional Testing <lkft@linaro.org>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: dri-devel@lists.freedesktop.org
Cc: Dave Airlie <airlied@redhat.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/478296/
|
|
Backmerging drm/drm-fixes for commit 3755d35ee1d2 ("drm/panel: Select
DRM_DP_HELPER for DRM_PANEL_EDP").
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
A recent change to how the SMB3 server (socket) and session status
is managed regressed multiuser mounts by changing the check
for whether session setup is needed to the socket (TCP_Server_info)
structure instead of the session struct (cifs_ses). Add additional
check in cifs_setup_sesion to fix this.
Fixes: 73f9bfbe3d81 ("cifs: maintain a state machine for tcp/smb/tcon sessions")
Reported-by: Ronnie Sahlberg <lsahlber@redhat.com>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
This kind of interface doesn't have a mac header. This patch fixes
bpf_redirect() to a PIM interface.
Fixes: 27b29f63058d ("bpf: add bpf_redirect() helper")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20220315092008.31423-1-nicolas.dichtel@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fix from Ard Biesheuvel:
"Avoid spurious warnings about unknown boot parameters"
* tag 'efi-urgent-for-v5.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi: fix return value of __setup handlers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a bug where qcom-rng can return a buffer that is not
completely filled with random data"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: qcom-rng - ensure buffer for generate is completely filled
|
|
This reverts commit 869f0ec048dc8fd88c0b2003373bd985795179fb. That
updated the expected device tree binding format for the ls-extirq
driver, without also updating the parsing code (ls_extirq_parse_map)
to the new format.
The context is that the ls-extirq driver uses the standard
"interrupt-map" OF property in a non-standard way, as suggested by
Rob Herring during review:
https://lore.kernel.org/lkml/20190927161118.GA19333@bogus/
This has turned out to be problematic, as Marc Zyngier discovered
through commit 041284181226 ("of/irq: Allow matching of an interrupt-map
local to an interrupt controller"), later fixed through commit
de4adddcbcc2 ("of/irq: Add a quirk for controllers with their own
definition of interrupt-map"). Marc's position, expressed on multiple
opportunities, is that:
(a) [ making private use of the reserved "interrupt-map" name in a
driver ] "is wrong, by the very letter of what an interrupt-map
means. If the interrupt map points to an interrupt controller,
that's the target for the interrupt."
https://lore.kernel.org/lkml/87k0g8jlmg.wl-maz@kernel.org/
(b) [ updating the driver's bindings to accept a non-reserved name for
this property, as an alternative, is ] "is totally pointless. These
machines have been in the wild for years, and existing DTs will be
there *forever*."
https://lore.kernel.org/lkml/87ilvrk1r0.wl-maz@kernel.org/
Considering the above, the Linux kernel has quirks in place to deal with
the ls-extirq's non-standard use of the "interrupt-map". These quirks
may be needed in other operating systems that consume this device tree,
yet this is seen as the only viable solution.
Therefore, the premise of the patch being reverted here is invalid.
It doesn't matter whether the driver, in its non-standard use of the
property, complies to the standard format or not, since this property
isn't expected to be used for interrupt translation by the core.
This change restores LS1088A, LS2088A/LS2085A and LX2160A to their
previous bindings, which allows these systems to continue to use
external interrupt lines with the correct polarity.
Fixes: 869f0ec048dc ("arm64: dts: freescale: Fix 'interrupt-map' parent address cells")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2022-03-16
1) Fix a kernel-info-leak in pfkey.
From Haimin Zhang.
2) Fix an incorrect check of the return value of ipv6_skip_exthdr.
From Sabrina Dubroca.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
esp6: fix check on ipv6_skip_exthdr's return value
af_key: add __GFP_ZERO flag for compose_sadb_supported in function pfkey_register
====================
Link: https://lore.kernel.org/r/20220316121142.3142336-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v5.17
Third set of fixes for v5.17. We have only one revert to fix an ath10k
regression.
* tag 'wireless-2022-03-16' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
Revert "ath10k: drop beacon and probe response which leak from other channel"
====================
Link: https://lore.kernel.org/r/20220316130249.B5225C340EC@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|