| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf and netfilter.
Current release - new code bugs:
- mctp: correct mctp_i2c_header_create result
- eth: fungible: fix reference to __udivdi3 on 32b builds
- eth: micrel: remove latencies support lan8814
Previous releases - regressions:
- bpf: resolve to prog->aux->dst_prog->type only for BPF_PROG_TYPE_EXT
- vrf: fix packet sniffing for traffic originating from ip tunnels
- rxrpc: fix a race in rxrpc_exit_net()
- dsa: revert "net: dsa: stop updating master MTU from master.c"
- eth: ice: fix MAC address setting
Previous releases - always broken:
- tls: fix slab-out-of-bounds bug in decrypt_internal
- bpf: support dual-stack sockets in bpf_tcp_check_syncookie
- xdp: fix coalescing for page_pool fragment recycling
- ovs: fix leak of nested actions
- eth: sfc:
- add missing xdp queue reinitialization
- fix using uninitialized xdp tx_queue
- eth: ice:
- clear default forwarding VSI during VSI release
- fix broken IFF_ALLMULTI handling
- synchronize_rcu() when terminating rings
- eth: qede: confirm skb is allocated before using
- eth: aqc111: fix out-of-bounds accesses in RX fixup
- eth: slip: fix NPD bug in sl_tx_timeout()"
* tag 'net-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (61 commits)
drivers: net: slip: fix NPD bug in sl_tx_timeout()
bpf: Adjust bpf_tcp_check_syncookie selftest to test dual-stack sockets
bpf: Support dual-stack sockets in bpf_tcp_check_syncookie
myri10ge: fix an incorrect free for skb in myri10ge_sw_tso
net: usb: aqc111: Fix out-of-bounds accesses in RX fixup
qede: confirm skb is allocated before using
net: ipv6mr: fix unused variable warning with CONFIG_IPV6_PIMSM_V2=n
net: phy: mscc-miim: reject clause 45 register accesses
net: axiemac: use a phandle to reference pcs_phy
dt-bindings: net: add pcs-handle attribute
net: axienet: factor out phy_node in struct axienet_local
net: axienet: setup mdio unconditionally
net: sfc: fix using uninitialized xdp tx_queue
rxrpc: fix a race in rxrpc_exit_net()
net: openvswitch: fix leak of nested actions
net: ethernet: mv643xx: Fix over zealous checking of_get_mac_address()
net: openvswitch: don't send internal clone attribute to the userspace.
net: micrel: Fix KS8851 Kconfig
ice: clear cmd_type_offset_bsz for TX rings
ice: xsk: fix VSI state check in ice_xsk_wakeup()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- Correctly propagate coherence information for VMbus devices (Michael
Kelley)
- Disable balloon and memory hot-add on ARM64 temporarily (Boqun Feng)
- Use barrier to prevent reording when reading ring buffer (Michael
Kelley)
- Use virt_store_mb in favour of smp_store_mb (Andrea Parri)
- Fix VMbus device object initialization (Andrea Parri)
- Deactivate sysctl_record_panic_msg on isolated guest (Andrea Parri)
- Fix a crash when unloading VMbus module (Guilherme G. Piccoli)
* tag 'hyperv-fixes-signed-20220407' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
Drivers: hv: vmbus: Replace smp_store_mb() with virt_store_mb()
Drivers: hv: balloon: Disable balloon and hot-add accordingly
Drivers: hv: balloon: Support status report for larger page sizes
Drivers: hv: vmbus: Prevent load re-ordering when reading ring buffer
PCI: hv: Propagate coherence from VMbus device to PCI device
Drivers: hv: vmbus: Propagate VMbus coherence to each VMbus device
Drivers: hv: vmbus: Fix potential crash on module unload
Drivers: hv: vmbus: Fix initialization of device object in vmbus_device_register()
Drivers: hv: vmbus: Deactivate sysctl_record_panic_msg by default in isolated guests
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator fixes from Jason Donenfeld:
- Another fixup to the fast_init/crng_init split, this time in how much
entropy is being credited, from Jan Varho.
- As discussed, we now opportunistically call try_to_generate_entropy()
in /dev/urandom reads, as a replacement for the reverted commit. I
opted to not do the more invasive wait_for_random_bytes() change at
least for now, preferring to do something smaller and more obvious
for the time being, but maybe that can be revisited as things evolve
later.
- Userspace can use FUSE or userfaultfd or simply move a process to
idle priority in order to make a read from the random device never
complete, which breaks forward secrecy, fixed by overwriting
sensitive bytes early on in the function.
- Jann Horn noticed that /dev/urandom reads were only checking for
pending signals if need_resched() was true, a bug going back to the
genesis commit, now fixed by always checking for signal_pending() and
calling cond_resched(). This explains various noticeable signal
delivery delays I've seen in programs over the years that do long
reads from /dev/urandom.
- In order to be more like other devices (e.g. /dev/zero) and to
mitigate the impact of fixing the above bug, which has been around
forever (users have never really needed to check the return value of
read() for medium-sized reads and so perhaps many didn't), we now
move signal checking to the bottom part of the loop, and do so every
PAGE_SIZE-bytes.
* tag 'random-5.18-rc2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
random: check for signals every PAGE_SIZE chunk of /dev/[u]random
random: check for signal_pending() outside of need_resched() check
random: do not allow user to keep crng key around on stack
random: opportunistically initialize on /dev/urandom reads
random: do not split fast init input in add_hwgenerator_randomness()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata fixes from Damien Le Moal:
- Fix a compilation warning due to an uninitialized variable in
ata_sff_lost_interrupt(), from me.
- Fix invalid internal command tag handling in the sata_dwc_460ex
driver, from Christian.
- Disable READ LOG DMA EXT with Samsung 840 EVO SSDs as this command
causes the drives to hang, from Christian.
- Change the config option CONFIG_SATA_LPM_POLICY back to its original
name CONFIG_SATA_LPM_MOBILE_POLICY to avoid potential problems with
users losing their configuration (as discussed during the merge
window), from Mario.
* tag 'ata-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: ahci: Rename CONFIG_SATA_LPM_POLICY configuration item back
ata: libata-core: Disable READ LOG DMA EXT for Samsung 840 EVOs
ata: sata_dwc_460ex: Fix crash due to OOB write
ata: libata-sff: Fix compilation warning in ata_sff_lost_interrupt()
|
|
When a slip driver is detaching, the slip_close() will act to
cleanup necessary resources and sl->tty is set to NULL in
slip_close(). Meanwhile, the packet we transmit is blocked,
sl_tx_timeout() will be called. Although slip_close() and
sl_tx_timeout() use sl->lock to synchronize, we don`t judge
whether sl->tty equals to NULL in sl_tx_timeout() and the
null pointer dereference bug will happen.
(Thread 1) | (Thread 2)
| slip_close()
| spin_lock_bh(&sl->lock)
| ...
... | sl->tty = NULL //(1)
sl_tx_timeout() | spin_unlock_bh(&sl->lock)
spin_lock(&sl->lock); |
... | ...
tty_chars_in_buffer(sl->tty)|
if (tty->ops->..) //(2) |
... | synchronize_rcu()
We set NULL to sl->tty in position (1) and dereference sl->tty
in position (2).
This patch adds check in sl_tx_timeout(). If sl->tty equals to
NULL, sl_tx_timeout() will goto out.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20220405132206.55291-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf 2022-04-06
We've added 8 non-merge commits during the last 8 day(s) which contain
a total of 9 files changed, 139 insertions(+), 36 deletions(-).
The main changes are:
1) rethook related fixes, from Jiri and Masami.
2) Fix the case when tracing bpf prog is attached to struct_ops, from Martin.
3) Support dual-stack sockets in bpf_tcp_check_syncookie, from Maxim.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Adjust bpf_tcp_check_syncookie selftest to test dual-stack sockets
bpf: Support dual-stack sockets in bpf_tcp_check_syncookie
bpf: selftests: Test fentry tracing a struct_ops program
bpf: Resolve to prog->aux->dst_prog->type only for BPF_PROG_TYPE_EXT
rethook: Fix to use WRITE_ONCE() for rethook:: Handler
selftests/bpf: Fix warning comparing pointer to 0
bpf: Fix sparse warnings in kprobe_multi_resolve_syms
bpftool: Explicit errno handling in skeletons
====================
Link: https://lore.kernel.org/r/20220407031245.73026-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In 1448769c9cdb ("random: check for signal_pending() outside of
need_resched() check"), Jann pointed out that we previously were only
checking the TIF_NOTIFY_SIGNAL and TIF_SIGPENDING flags if the process
had TIF_NEED_RESCHED set, which meant in practice, super long reads to
/dev/[u]random would delay signal handling by a long time. I tried this
using the below program, and indeed I wasn't able to interrupt a
/dev/urandom read until after several megabytes had been read. The bug
he fixed has always been there, and so code that reads from /dev/urandom
without checking the return value of read() has mostly worked for a long
time, for most sizes, not just for <= 256.
Maybe it makes sense to keep that code working. The reason it was so
small prior, ignoring the fact that it didn't work anyway, was likely
because /dev/random used to block, and that could happen for pretty
large lengths of time while entropy was gathered. But now, it's just a
chacha20 call, which is extremely fast and is just operating on pure
data, without having to wait for some external event. In that sense,
/dev/[u]random is a lot more like /dev/zero.
Taking a page out of /dev/zero's read_zero() function, it always returns
at least one chunk, and then checks for signals after each chunk. Chunk
sizes there are of length PAGE_SIZE. Let's just copy the same thing for
/dev/[u]random, and check for signals and cond_resched() for every
PAGE_SIZE amount of data. This makes the behavior more consistent with
expectations, and should mitigate the impact of Jann's fix for the
age-old signal check bug.
---- test program ----
#include <unistd.h>
#include <signal.h>
#include <stdio.h>
#include <sys/random.h>
static unsigned char x[~0U];
static void handle(int) { }
int main(int argc, char *argv[])
{
pid_t pid = getpid(), child;
signal(SIGUSR1, handle);
if (!(child = fork())) {
for (;;)
kill(pid, SIGUSR1);
}
pause();
printf("interrupted after reading %zd bytes\n", getrandom(x, sizeof(x), 0));
kill(child, SIGTERM);
return 0;
}
Cc: Jann Horn <jannh@google.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
The previous commit fixed support for dual-stack sockets in
bpf_tcp_check_syncookie. This commit adjusts the selftest to verify the
fixed functionality.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Arthur Fabre <afabre@cloudflare.com>
Link: https://lore.kernel.org/bpf/20220406124113.2795730-2-maximmi@nvidia.com
|
|
bpf_tcp_gen_syncookie looks at the IP version in the IP header and
validates the address family of the socket. It supports IPv4 packets in
AF_INET6 dual-stack sockets.
On the other hand, bpf_tcp_check_syncookie looks only at the address
family of the socket, ignoring the real IP version in headers, and
validates only the packet size. This implementation has some drawbacks:
1. Packets are not validated properly, allowing a BPF program to trick
bpf_tcp_check_syncookie into handling an IPv6 packet on an IPv4
socket.
2. Dual-stack sockets fail the checks on IPv4 packets. IPv4 clients end
up receiving a SYNACK with the cookie, but the following ACK gets
dropped.
This patch fixes these issues by changing the checks in
bpf_tcp_check_syncookie to match the ones in bpf_tcp_gen_syncookie. IP
version from the header is taken into account, and it is validated
properly with address family.
Fixes: 399040847084 ("bpf: add helper to check for a valid SYN cookie")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Acked-by: Arthur Fabre <afabre@cloudflare.com>
Link: https://lore.kernel.org/bpf/20220406124113.2795730-1-maximmi@nvidia.com
|
|
All remaining skbs should be released when myri10ge_xmit fails to
transmit a packet. Fix it within another skb_list_walk_safe.
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
aqc111_rx_fixup() contains several out-of-bounds accesses that can be
triggered by a malicious (or defective) USB device, in particular:
- The metadata array (desc_offset..desc_offset+2*pkt_count) can be out of bounds,
causing OOB reads and (on big-endian systems) OOB endianness flips.
- A packet can overlap the metadata array, causing a later OOB
endianness flip to corrupt data used by a cloned SKB that has already
been handed off into the network stack.
- A packet SKB can be constructed whose tail is far beyond its end,
causing out-of-bounds heap data to be considered part of the SKB's
data.
Found doing variant analysis. Tested it with another driver (ax88179_178a), since
I don't have a aqc111 device to test it, but the code looks very similar.
Signed-off-by: Marcin Kozlowski <marcinguy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qede_build_skb() assumes build_skb() always works and goes straight
to skb_reserve(). However, build_skb() can fail under memory pressure.
This results in a kernel panic because the skb to reserve is NULL.
Add a check in case build_skb() failed to allocate and return NULL.
The NULL return is handled correctly in callers to qede_build_skb().
Fixes: 8a8633978b842 ("qede: Add build_skb() support.")
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/ipv6/ip6mr.c:1656:14: warning: unused variable 'do_wrmifwhole'
Move it to the CONFIG_IPV6_PIMSM_V2 scope where its used.
Fixes: 4b340a5a726d ("net: ip6mr: add support for passing full packet on wrong mif")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-04-05
Maciej Fijalkowski says:
We were solving issues around AF_XDP busy poll's not-so-usual scenarios,
such as very big busy poll budgets applied to very small HW rings. This
set carries the things that were found during that work that apply to
net tree.
One thing that was fixed for all in-tree ZC drivers was missing on ice
side all the time - it's about syncing RCU before destroying XDP
resources. Next one fixes the bit that is checked in ice_xsk_wakeup and
third one avoids false setting of DD bits on Tx descriptors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following the recommendation in Documentation/memory-barriers.txt for
virtual machine guests.
Fixes: 8b6a877c060ed ("Drivers: hv: vmbus: Replace the per-CPU channel lists with a global array of channels")
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Link: https://lore.kernel.org/r/20220328154457.100872-1-parri.andrea@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
Currently there are known potential issues for balloon and hot-add on
ARM64:
* Unballoon requests from Hyper-V should only unballoon ranges
that are guest page size aligned, otherwise guests cannot handle
because it's impossible to partially free a page. This is a
problem when guest page size > 4096 bytes.
* Memory hot-add requests from Hyper-V should provide the NUMA
node id of the added ranges or ARM64 should have a functional
memory_add_physaddr_to_nid(), otherwise the node id is missing
for add_memory().
These issues require discussions on design and implementation. In the
meanwhile, post_status() is working and essential to guest monitoring.
Therefore instead of disabling the entire hv_balloon driver, the
ballooning (when page size > 4096 bytes) and hot-add are disabled
accordingly for now. Once the issues are fixed, they can be re-enable in
these cases.
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20220325023212.1570049-3-boqun.feng@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
DM_STATUS_REPORT expects the numbers of pages in the unit of 4k pages
(HV_HYP_PAGE) instead of guest pages, so to make it work when guest page
sizes are larger than 4k, convert the numbers of guest pages into the
numbers of HV_HYP_PAGEs.
Note that the numbers of guest pages are still used for tracing because
tracing is internal to the guest kernel.
Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20220325023212.1570049-2-boqun.feng@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
signal_pending() checks TIF_NOTIFY_SIGNAL and TIF_SIGPENDING, which
signal that the task should bail out of the syscall when possible. This
is a separate concept from need_resched(), which checks
TIF_NEED_RESCHED, signaling that the task should preempt.
In particular, with the current code, the signal_pending() bailout
probably won't work reliably.
Change this to look like other functions that read lots of data, such as
read_zero().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
The fast key erasure RNG design relies on the key that's used to be used
and then discarded. We do this, making judicious use of
memzero_explicit(). However, reads to /dev/urandom and calls to
getrandom() involve a copy_to_user(), and userspace can use FUSE or
userfaultfd, or make a massive call, dynamically remap memory addresses
as it goes, and set the process priority to idle, in order to keep a
kernel stack alive indefinitely. By probing
/proc/sys/kernel/random/entropy_avail to learn when the crng key is
refreshed, a malicious userspace could mount this attack every 5 minutes
thereafter, breaking the crng's forward secrecy.
In order to fix this, we just overwrite the stack's key with the first
32 bytes of the "free" fast key erasure output. If we're returning <= 32
bytes to the user, then we can still return those bytes directly, so
that short reads don't become slower. And for long reads, the difference
is hopefully lost in the amortization, so it doesn't change much, with
that amortization helping variously for medium reads.
We don't need to do this for get_random_bytes() and the various
kernel-space callers, and later, if we ever switch to always batching,
this won't be necessary either, so there's no need to change the API of
these functions.
Cc: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jann Horn <jannh@google.com>
Fixes: c92e040d575a ("random: add backtracking protection to the CRNG")
Fixes: 186873c549df ("random: use simpler fast key erasure flow on per-cpu keys")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
The driver doesn't support clause 45 register access yet, but doesn't
check if the access is a c45 one either. This leads to spurious register
reads and writes. Add the check.
Fixes: 542671fe4d86 ("net: phy: mscc-miim: Add MDIO driver")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andy Chiu says:
====================
Fix broken link on Xilinx's AXI Ethernet in SGMII mode
The Ethernet driver use phy-handle to reference the PCS/PMA PHY. This
could be a problem if one wants to configure an external PHY via phylink,
since it use the same phandle to get the PHY. To fix this, introduce a
dedicated pcs-handle to point to the PCS/PMA PHY and deprecate the use
of pointing it with phy-handle. A similar use case of pcs-handle can be
seen on dpaa2 as well.
--- patch v5 ---
- Re-apply the v4 patch on the net tree.
- Describe the pcs-handle DT binding at ethernet-controller level.
--- patch v6 ---
- Remove "preferrably" to clearify usage of pcs_handle.
--- patch v7 ---
- Rebase the patch on latest net/master
--- patch v8 ---
- Rebase the patch on net-next/master
- Add "reviewed-by" tag in PATCH 3/4: dt-bindings: net: add pcs-handle
attribute
- Remove "fix" tag in last commit message since this is not a critical
bug and will not be back ported to stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some SGMII use cases where both a fixed link external PHY and the
internal PCS/PMA PHY need to be configured, we should explicitly use a
phandle "pcs-phy" to get the reference to the PCS/PMA PHY. Otherwise, the
driver would use "phy-handle" in the DT as the reference to both the
external and the internal PCS/PMA PHY.
In other cases where the core is connected to a SFP cage, we could still
point phy-handle to the intenal PCS/PMA PHY, and let the driver connect
to the SFP module, if exist, via phylink.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Document the new pcs-handle attribute to support connecting to an
external PHY. For Xilinx's AXI Ethernet, this is used when the core
operates in SGMII or 1000Base-X modes and links through the internal
PCS/PMA PHY.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the struct member `phy_node` of struct axienet_local is not used by the
driver anymore after initialization. It might be a remnent of old code
and could be removed.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The call to axienet_mdio_setup should not depend on whether "phy-node"
pressents on the DT. Besides, since `lp->phy_node` is used if PHY is in
SGMII or 100Base-X modes, move it into the if statement. And the next patch
will remove `lp->phy_node` from driver's private structure and do an
of_node_put on it right away after use since it is not used elsewhere.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some cases, xdp tx_queue can get used before initialization.
1. interface up/down
2. ring buffer size change
When CPU cores are lower than maximum number of channels of sfc driver,
it creates new channels only for XDP.
When an interface is up or ring buffer size is changed, all channels
are initialized.
But xdp channels are always initialized later.
So, the below scenario is possible.
Packets are received to rx queue of normal channels and it is acted
XDP_TX and tx_queue of xdp channels get used.
But these tx_queues are not initialized yet.
If so, TX DMA or queue error occurs.
In order to avoid this problem.
1. initializes xdp tx_queues earlier than other rx_queue in
efx_start_channels().
2. checks whether tx_queue is initialized or not in efx_xdp_tx_buffers().
Splat looks like:
sfc 0000:08:00.1 enp8s0f1np1: TX queue 10 spurious TX completion id 250
sfc 0000:08:00.1 enp8s0f1np1: resetting (RECOVER_OR_ALL)
sfc 0000:08:00.1 enp8s0f1np1: MC command 0x80 inlen 100 failed rc=-22
(raw=22) arg=789
sfc 0000:08:00.1 enp8s0f1np1: has been disabled
Fixes: f28100cb9c96 ("sfc: fix lack of XDP TX queues - error XDP TX failed (-22)")
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current code can lead to the following race:
CPU0 CPU1
rxrpc_exit_net()
rxrpc_peer_keepalive_worker()
if (rxnet->live)
rxnet->live = false;
del_timer_sync(&rxnet->peer_keepalive_timer);
timer_reduce(&rxnet->peer_keepalive_timer, jiffies + delay);
cancel_work_sync(&rxnet->peer_keepalive_work);
rxrpc_exit_net() exits while peer_keepalive_timer is still armed,
leading to use-after-free.
syzbot report was:
ODEBUG: free active (active state 0) object type: timer_list hint: rxrpc_peer_keepalive_timeout+0x0/0xb0
WARNING: CPU: 0 PID: 3660 at lib/debugobjects.c:505 debug_print_object+0x16e/0x250 lib/debugobjects.c:505
Modules linked in:
CPU: 0 PID: 3660 Comm: kworker/u4:6 Not tainted 5.17.0-syzkaller-13993-g88e6c0207623 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: netns cleanup_net
RIP: 0010:debug_print_object+0x16e/0x250 lib/debugobjects.c:505
Code: ff df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 af 00 00 00 48 8b 14 dd 00 1c 26 8a 4c 89 ee 48 c7 c7 00 10 26 8a e8 b1 e7 28 05 <0f> 0b 83 05 15 eb c5 09 01 48 83 c4 18 5b 5d 41 5c 41 5d 41 5e c3
RSP: 0018:ffffc9000353fb00 EFLAGS: 00010082
RAX: 0000000000000000 RBX: 0000000000000003 RCX: 0000000000000000
RDX: ffff888029196140 RSI: ffffffff815efad8 RDI: fffff520006a7f52
RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff815ea4ae R11: 0000000000000000 R12: ffffffff89ce23e0
R13: ffffffff8a2614e0 R14: ffffffff816628c0 R15: dffffc0000000000
FS: 0000000000000000(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe1f2908924 CR3: 0000000043720000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
__debug_check_no_obj_freed lib/debugobjects.c:992 [inline]
debug_check_no_obj_freed+0x301/0x420 lib/debugobjects.c:1023
kfree+0xd6/0x310 mm/slab.c:3809
ops_free_list.part.0+0x119/0x370 net/core/net_namespace.c:176
ops_free_list net/core/net_namespace.c:174 [inline]
cleanup_net+0x591/0xb00 net/core/net_namespace.c:598
process_one_work+0x996/0x1610 kernel/workqueue.c:2289
worker_thread+0x665/0x1080 kernel/workqueue.c:2436
kthread+0x2e9/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:298
</TASK>
Fixes: ace45bec6d77 ("rxrpc: Fix firewall route keepalive")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Marc Dionne <marc.dionne@auristor.com>
Cc: linux-afs@lists.infradead.org
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While parsing user-provided actions, openvswitch module may dynamically
allocate memory and store pointers in the internal copy of the actions.
So this memory has to be freed while destroying the actions.
Currently there are only two such actions: ct() and set(). However,
there are many actions that can hold nested lists of actions and
ovs_nla_free_flow_actions() just jumps over them leaking the memory.
For example, removal of the flow with the following actions will lead
to a leak of the memory allocated by nf_ct_tmpl_alloc():
actions:clone(ct(commit),0)
Non-freed set() action may also leak the 'dst' structure for the
tunnel info including device references.
Under certain conditions with a high rate of flow rotation that may
cause significant memory leak problem (2MB per second in reporter's
case). The problem is also hard to mitigate, because the user doesn't
have direct control over the datapath flows generated by OVS.
Fix that by iterating over all the nested actions and freeing
everything that needs to be freed recursively.
New build time assertion should protect us from this problem if new
actions will be added in the future.
Unfortunately, openvswitch module doesn't use NLA_F_NESTED, so all
attributes has to be explicitly checked. sample() and clone() actions
are mixing extra attributes into the user-provided action list. That
prevents some code generalization too.
Fixes: 34ae932a4036 ("openvswitch: Make tunnel set action attach a metadata dst")
Link: https://mail.openvswitch.org/pipermail/ovs-dev/2022-March/392922.html
Reported-by: Stéphane Graber <stgraber@ubuntu.com>
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CONFIG_SATA_LPM_MOBILE_POLICY was renamed to CONFIG_SATA_LPM_POLICY in
commit 4dd4d3deb502 ("ata: ahci: Rename CONFIG_SATA_LPM_MOBILE_POLICY
configuration item").
This can potentially cause problems as users would invisibly lose
configuration policy defaults when they built the new kernel. To
avoid such problems, switch back to the old name (even if it's wrong).
Suggested-by: Christoph Hellwig <hch@infradead.org>
Suggested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
There is often not a MAC address available in an EEPROM accessible by
Linux with Marvell devices. Instead the bootload has the MAC address
and directly programs it into the hardware. So don't consider an error
from of_get_mac_address() has fatal. However, the check was added for
the case where there is a MAC address in an the EEPROM, but the EEPROM
has not probed yet, and -EPROBE_DEFER is returned. In that case the
error should be returned. So make the check specific to this error
code.
Cc: Mauri Sandberg <maukka@ext.kapsi.fi>
Reported-by: Thomas Walther <walther-it@gmx.de>
Fixes: 42404d8f1c01 ("net: mv643xx_eth: process retval from of_get_mac_address")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220405000404.3374734-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'OVS_CLONE_ATTR_EXEC' is an internal attribute that is used for
performance optimization inside the kernel. It's added by the kernel
while parsing user-provided actions and should not be sent during the
flow dump as it's not part of the uAPI.
The issue doesn't cause any significant problems to the ovs-vswitchd
process, because reported actions are not really used in the
application lifecycle and only supposed to be shown to a human via
ovs-dpctl flow dump. However, the action list is still incorrect
and causes the following error if the user wants to look at the
datapath flows:
# ovs-dpctl add-dp system@ovs-system
# ovs-dpctl add-flow "<flow match>" "clone(ct(commit),0)"
# ovs-dpctl dump-flows
<flow match>, packets:0, bytes:0, used:never,
actions:clone(bad length 4, expected -1 for: action0(01 00 00 00),
ct(commit),0)
With the fix:
# ovs-dpctl dump-flows
<flow match>, packets:0, bytes:0, used:never,
actions:clone(ct(commit),0)
Additionally fixed an incorrect attribute name in the comment.
Fixes: b233504033db ("openvswitch: kernel datapath clone action")
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/20220404104150.2865736-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KS8851 selects MICREL_PHY, which depends on PTP_1588_CLOCK_OPTIONAL, so
make KS8851 also depend on PTP_1588_CLOCK_OPTIONAL.
Fixes kconfig warning and build errors:
WARNING: unmet direct dependencies detected for MICREL_PHY
Depends on [m]: NETDEVICES [=y] && PHYLIB [=y] && PTP_1588_CLOCK_OPTIONAL [=m]
Selected by [y]:
- KS8851 [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICREL [=y] && SPI [=y]
ld.lld: error: undefined symbol: ptp_clock_register referenced by micrel.c
net/phy/micrel.o:(lan8814_probe) in archive drivers/built-in.a
ld.lld: error: undefined symbol: ptp_clock_index referenced by micrel.c
net/phy/micrel.o:(lan8814_ts_info) in archive drivers/built-in.a
Reported-by: kernel test robot <lkp@intel.com>
Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20220405065936.4105272-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Incorrect comparison in bitmask .reduce, from Jeremy Sowden.
2) Missing GFP_KERNEL_ACCOUNT for dynamically allocated objects,
from Vasily Averin.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: memcg accounting for dynamically allocated objects
netfilter: bitwise: fix reduce comparisons
====================
Link: https://lore.kernel.org/r/20220405100923.7231-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull virtio fixes from Michael Tsirkin:
"Fixes and cleanups:
- A couple of mlx5 fixes related to cvq
- A couple of reverts dropping useless code (code that used it got
reverted earlier)"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa: mlx5: synchronize driver status with CVQ
vdpa: mlx5: prevent cvq work from hogging CPU
Revert "virtio_config: introduce a new .enable_cbs method"
Revert "virtio: use virtio_device_ready() in virtio_device_restore()"
|
|
After resuming from suspend-to-RAM, the MSRs that control CPU's
speculative execution behavior are not being restored on the boot CPU.
These MSRs are used to mitigate speculative execution vulnerabilities.
Not restoring them correctly may leave the CPU vulnerable. Secondary
CPU's MSRs are correctly being restored at S3 resume by
identify_secondary_cpu().
During S3 resume, restore these MSRs for boot CPU when restoring its
processor state.
Fixes: 772439717dbf ("x86/bugs/intel: Set proper CPU features and setup RDS")
Reported-by: Neelima Krishnan <neelima.krishnan@intel.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Tested-by: Neelima Krishnan <neelima.krishnan@intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The mechanism to save/restore MSRs during S3 suspend/resume checks for
the MSR validity during suspend, and only restores the MSR if its a
valid MSR. This is not optimal, as an invalid MSR will unnecessarily
throw an exception for every suspend cycle. The more invalid MSRs,
higher the impact will be.
Check and save the MSR validity at setup. This ensures that only valid
MSRs that are guaranteed to not throw an exception will be attempted
during suspend.
Fixes: 7a9c2dd08ead ("x86/pm: Introduce quirk framework to save/restore extra MSR registers around suspend/resume")
Suggested-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently when XDP rings are created, each descriptor gets its DD bit
set, which turns out to be the wrong approach as it can lead to a
situation where more descriptors get cleaned than it was supposed to,
e.g. when AF_XDP busy poll is run with a large batch size. In this
situation, the driver would request for more buffers than it is able to
handle.
Fix this by not setting the DD bits in ice_xdp_alloc_setup_rings(). They
should be initialized to zero instead.
Fixes: 9610bd988df9 ("ice: optimize XDP_TX workloads")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ICE_DOWN is dedicated for pf->state. Check for ICE_VSI_DOWN being set on
vsi->state in ice_xsk_wakeup().
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Unfortunately, the ice driver doesn't respect the RCU critical section that
XSK wakeup is surrounded with. To fix this, add synchronize_rcu() calls to
paths that destroy resources that might be in use.
This was addressed in other AF_XDP ZC enabled drivers, for reference see
for example commit b3873a5be757 ("net/i40e: Fix concurrency issues
between config flow and XSK")
Fixes: efc2214b6047 ("ice: Add support for XDP")
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- prevent deleting subvolume with active swapfile
- fix qgroup reserve limit calculation overflow
- remove device count in superblock and its item in one transaction so
they cant't get out of sync
- skip defragmenting an isolated sector, this could cause some extra IO
- unify handling of mtime/permissions in hole punch with fallocate
- zoned mode fixes:
- remove assert checking for only single mode, we have the
DUP mode implemented
- fix potential lockdep warning while traversing devices
when checking for zone activation
* tag 'for-5.18-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: prevent subvol with swapfile from being deleted
btrfs: do not warn for free space inode in cow_file_range
btrfs: avoid defragging extents whose next extents are not targets
btrfs: fix fallocate to use file_modified to update permissions consistently
btrfs: remove device item and update super block in the same transaction
btrfs: fix qgroup reserve overflow the qgroup limit
btrfs: zoned: remove left over ASSERT checking for single profile
btrfs: zoned: traverse devices under chunk_mutex in btrfs_can_activate_zone
|
|
In 6f98a4bfee72 ("random: block in /dev/urandom"), we tried to make a
successful try_to_generate_entropy() call *required* if the RNG was not
already initialized. Unfortunately, weird architectures and old
userspaces combined in TCG test harnesses, making that change still not
realistic, so it was reverted in 0313bc278dac ("Revert "random: block in
/dev/urandom"").
However, rather than making a successful try_to_generate_entropy() call
*required*, we can instead make it *best-effort*.
If try_to_generate_entropy() fails, it fails, and nothing changes from
the current behavior. If it succeeds, then /dev/urandom becomes safe to
use for free. This way, we don't risk the regression potential that led
to us reverting the required-try_to_generate_entropy() call before.
Practically speaking, this means that at least on x86, /dev/urandom
becomes safe. Probably other architectures with working cycle counters
will also become safe. And architectures with slow or broken cycle
counters at least won't be affected at all by this change.
So it may not be the glorious "all things are unified!" change we were
hoping for initially, but practically speaking, it makes a positive
impact.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
VRF devices are the loopbacks for VRFs, and a loopback can not be
assigned to a VRF. Accordingly, the condition in ip6_pkt_drop should
be '||' not '&&'.
Fixes: 1d3fd8a10bed ("vrf: Use orig netdev to count Ip6InNoRoutes and a fresh route lookup when sending dest unreach")
Reported-by: Pudak, Filip <Filip.Pudak@windriver.com>
Reported-by: Xiao, Jiguang <Jiguang.Xiao@windriver.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220404150908.2937-1-dsahern@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Tony Nguyen says:
====================
ice bug fixes
Alice Michael says:
There were a couple of bugs that have been found and
fixed by Anatolii in the ice driver. First he fixed
a bug on ring creation by setting the default value
for the teid. Anatolli also fixed a bug with deleting
queues in ice_vc_dis_qs_msg based on their enablement.
---
v2: Remove empty lines between tags
The following are changes since commit 458f5d92df4807e2a7c803ed928369129996bf96:
sfc: Do not free an empty page_ring
and are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue 100GbE
====================
Link: https://lore.kernel.org/r/20220404183548.3422851-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Disable check for queue being enabled in ice_vc_dis_qs_msg, because
there could be a case when queues were created, but were not enabled.
We still need to delete those queues.
Normal workflow for VF looks like:
Enable path:
VIRTCHNL_OP_ADD_ETH_ADDR (opcode 10)
VIRTCHNL_OP_CONFIG_VSI_QUEUES (opcode 6)
VIRTCHNL_OP_ENABLE_QUEUES (opcode 8)
Disable path:
VIRTCHNL_OP_DISABLE_QUEUES (opcode 9)
VIRTCHNL_OP_DEL_ETH_ADDR (opcode 11)
The issue appears only in stress conditions when VF is enabled and
disabled very fast.
Eventually there will be a case, when queues are created by
VIRTCHNL_OP_CONFIG_VSI_QUEUES, but are not enabled by
VIRTCHNL_OP_ENABLE_QUEUES.
In turn, these queues are not deleted by VIRTCHNL_OP_DISABLE_QUEUES,
because there is a check whether queues are enabled in
ice_vc_dis_qs_msg.
When we bring up the VF again, we will see the "Failed to set LAN Tx queue
context" error during VIRTCHNL_OP_CONFIG_VSI_QUEUES step. This
happens because old 16 queues were not deleted and VF requests to create
16 more, but ice_sched_get_free_qparent in ice_ena_vsi_txq would fail to
find a parent node for first newly requested queue (because all nodes
are allocated to 16 old queues).
Testing Hints:
Just enable and disable VF fast enough, so it would be disabled before
reaching VIRTCHNL_OP_ENABLE_QUEUES.
while true; do
ip link set dev ens785f0v0 up
sleep 0.065 # adjust delay value for you machine
ip link set dev ens785f0v0 down
done
Fixes: 77ca27c41705 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When VF is freshly created, but not brought up, ring->txq_teid
value is by default set to 0.
But 0 is a valid TEID. On some platforms the Root Node of
Tx scheduler has a TEID = 0. This can cause issues as shown below.
The proper way is to set ring->txq_teid to ICE_INVAL_TEID (0xFFFFFFFF).
Testing Hints:
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
ip link set dev ens785f0v0 up
ip link set dev ens785f0v0 down
If we have freshly created VF and quickly turn it on and off, so there
would be no time to reach VIRTCHNL_OP_CONFIG_VSI_QUEUES stage, then
VIRTCHNL_OP_DISABLE_QUEUES stage will fail with error:
[ 639.531454] disable queue 89 failed 14
[ 639.532233] Failed to disable LAN Tx queues, error: ICE_ERR_AQ_ERROR
[ 639.533107] ice 0000:02:00.0: Failed to stop Tx ring 0 on VSI 5
The reason for the fail is that we are trying to send AQ command to
delete queue 89, which has never been created and receive an "invalid
argument" error from firmware.
As this queue has never been created, it's teid and ring->txq_teid
have default value 0.
ice_dis_vsi_txq has a check against non-existent queues:
node = ice_sched_find_node_by_teid(pi->root, q_teids[i]);
if (!node)
continue;
But on some platforms the Root Node of Tx scheduler has a teid = 0.
Hence, ice_sched_find_node_by_teid finds a node with teid = 0 (it is
pi->root), and we go further to submit an erroneous request to firmware.
Fixes: 37bb83901286 ("ice: Move common functions out of ice_main.c part 7/7")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This node pointer is returned by of_find_compatible_node() with
refcount incremented. Calling of_node_put() to aovid the refcount leak.
Fixes: d346c9e86d86 ("dpaa2-ptp: reuse ptp_qoriq driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220404125336.13427-1-linmq006@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
nft_*.c files whose NFT_EXPR_STATEFUL flag is set on need to
use __GFP_ACCOUNT flag for objects that are dynamically
allocated from the packet path.
Such objects are allocated inside nft_expr_ops->init() callbacks
executed in task context while processing netlink messages.
In addition, this patch adds accounting to nft_set_elem_expr_clone()
used for the same purposes.
Signed-off-by: Vasily Averin <vvs@openvz.org>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Singleton chunks (INIT, HEARTBEAT PMTU probes, and SHUTDOWN-
COMPLETE) are not counted in SCTP_GET_ASOC_STATS "sas_octrlchunks"
counter available to the assoc owner.
These are all control chunks so they should be counted as such.
Add counting of singleton chunks so they are properly accounted for.
Fixes: 196d67593439 ("sctp: Add support to per-association statistics via a new SCTP_GET_ASSOC_STATS call")
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/c9ba8785789880cf07923b8a5051e174442ea9ee.1649029663.git.jamie.bainbridge@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
add_hwgenerator_randomness() tries to only use the required amount of input
for fast init, but credits all the entropy, rather than a fraction of
it. Since it's hard to determine how much entropy is left over out of a
non-unformly random sample, either give it all to fast init or credit
it, but don't attempt to do both. In the process, we can clean up the
injection code to no longer need to return a value.
Signed-off-by: Jan Varho <jan.varho@gmail.com>
[Jason: expanded commit message]
Fixes: 73c7733f122e ("random: do not throw away excess input to crng_fast_load")
Cc: stable@vger.kernel.org # 5.17+, requires af704c856e88
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
When the page_ring is not used page_ptr_mask is 0.
Do not dereference page_ring[0] in this case.
Fixes: 2768935a4660 ("sfc: reuse pages to avoid DMA mapping/unmapping costs")
Reported-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
