| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net'
restricting a HW workaround alongside cleanups in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fix from Jacek Anaszewski:
"A single LED fix for 4.12-rc3.
leds-pca955x driver uses only i2c_smbus API and thus it should pass
I2C_FUNC_SMBUS_BYTE_DATA flag to i2c_check_functionality"
* tag 'led_fixes_for_4-12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: pca955x: Correct I2C Functionality
|
|
Pull networking fixes from David Miller:
1) Fix state pruning in bpf verifier wrt. alignment, from Daniel
Borkmann.
2) Handle non-linear SKBs properly in SCTP ICMP parsing, from Davide
Caratti.
3) Fix bit field definitions for rss_hash_type of descriptors in mlx5
driver, from Jesper Brouer.
4) Defer slave->link updates until bonding is ready to do a full commit
to the new settings, from Nithin Sujir.
5) Properly reference count ipv4 FIB metrics to avoid use after free
situations, from Eric Dumazet and several others including Cong Wang
and Julian Anastasov.
6) Fix races in llc_ui_bind(), from Lin Zhang.
7) Fix regression of ESP UDP encapsulation for TCP packets, from
Steffen Klassert.
8) Fix mdio-octeon driver Kconfig deps, from Randy Dunlap.
9) Fix regression in setting DSCP on ipv6/GRE encapsulation, from Peter
Dawson.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
ipv4: add reference counting to metrics
net: ethernet: ax88796: don't call free_irq without request_irq first
ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets
sctp: fix ICMP processing if skb is non-linear
net: llc: add lock_sock in llc_ui_bind to avoid a race condition
bonding: Don't update slave->link until ready to commit
test_bpf: Add a couple of tests for BPF_JSGE.
bpf: add various verifier test cases
bpf: fix wrong exposure of map_flags into fdinfo for lpm
bpf: add bpf_clone_redirect to bpf_helper_changes_pkt_data
bpf: properly reset caller saved regs after helper call and ld_abs/ind
bpf: fix incorrect pruning decision when alignment must be tracked
arp: fixed -Wuninitialized compiler warning
tcp: avoid fastopen API to be used on AF_UNSPEC
net: move somaxconn init from sysctl code
net: fix potential null pointer dereference
geneve: fix fill_info when using collect_metadata
virtio-net: enable TSO/checksum offloads for Q-in-Q vlans
be2net: Fix offload features for Q-in-Q packets
vlan: Fix tcp checksum offloads in Q-in-Q vlans
...
|
|
Nathan Fontenot says:
====================
ibmvnic: Driver updates
This set of patches implements several updates to the ibmvnic driver
to fix issues that have been found in testing. Most of the updates
invovle updating queue handling during driver close and reset
operations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the ibmvnic driver is resetting, we can just reset the sub crqs
instead of releasing all of their resources and re-allocting them.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When resetting the ibmvnic driver there is not a need to release
and re-allocate the resources for the tx and rx pools. These
resources can just be reset to avoid the re-allocations.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a driver reset operation occurs there is not a need to release
the CRQ resources and re-allocate them. Instead a reset of the CRQ
will suffice.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We do not want to process any receive frames if the ibmvnic_poll
routine is invoked while a reset is in process. Also, before
replenishing the rx pools in the ibmvnic_poll, we want to
make sure the adapter is not in the process of closing.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If H_CLOSED is returned, halt RX buffer replenishment activity
until firmware sends a notification that the driver can reset.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch disables transmissions and reports carrier off if xmit
function returns that the hardware TX queue is closed. The driver can
then await a signal from firmware to determine the correct reset method.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handle non-fatal error conditions. The process to do this when
resetting the driver is to just do __ibmvnic_close followed by
__ibmvnic_open.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A race condition occurs when closing the driver. Free'ing of skb's
can race between the close routine and ibmvnic_tx_interrupt. To fix
this we move the claenup of tx pools during close to after the
sub-CRQ interrupts are disabled.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Send gratuitous arp after any reset.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handle case where phyp sends a failover after failing to send the
init crq.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Track the state of ibmvnic napis. The driver can get into states where it
can be reset when napis are already disabled and attempting to disable them
again will cause the driver to hang.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko says:
====================
mlxsw: Improve extensibility
Ido says:
Since the initial introduction of the bridge offload in commit
56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
the per-port struct was used to store both physical properties of the
port as well as logical bridge properties such as learning and active
VLANs in the VLAN-aware bridge.
The above resulted in a bloated struct and code that is getting
increasingly difficult to extend when stacked devices are taken into
account as well as more advanced use cases such as IGMP snooping.
Due to the incremental development nature of this driver as well as the
complexity of the underlying hardware, subsequent design decisions failed
to generalize the FID and RIF resources, which could've benefited from
a more generic design, resulting in consolidated code paths and better
extensibility with regards to future ASICs and use cases.
This patchset tries to solve both of these design problems, as they're
tightly coupled. To ease the code review, the changes are done in a
bottom-up manner, in which the port struct is the first to be patched,
then the FIDs the ports are mapped to and finally the RIFs configured on
top.
The first half of the patchset gradually moves away from the previous
design to a design that is more in sync with the underlying hardware and
which clearly separates between hardware-specific structs and logical
ones such as a bridge port.
All the bridge-specific information is removed from the port struct, as
well as the list of VLAN devices ("vPorts") configured on top of it.
Instead, a linked list of VLANs is introduced, which allows each VLAN
to hold a state, such as mapping to a particular FID and membership in
a bridge. The data structures are depicted in the following figure:
mlxsw_sp_bridge_device
+----------+
| |
+----+ |
| | |
| +----------+
|
mlxsw_sp_bridge_port |
+----------+ |
| | |
+--> +-----+--> ..
| | |
| +----+-----+
| |
| v
| mlxsw_sp_bridge_vlan
| +----------+
| | vid X |
| | +--> ..
| | |
| +----+-----+
| |
+--+----v-----+
| vid X |
+--+ +--> ..
| | |
mlxsw_sp_port | +----------+
+----------+ | mlxsw_sp_port_vlan
| | |
| +--+
| |
+----------+
This model allows us to consolidate many of the code paths relating to
VLAN-aware and VLAN-unaware bridges, as the latter is simply represented
using a bridge port with a VLAN list size of one. Another advantage of
the model is that it's easy to extend it with future per-VLAN
attributes - such as mrouter indication - by merely pushing these down
from the bridge port struct to the bridge VLAN one.
The second half of the patchset builds on top of previous work and
prepares the driver for the common FID and RIF cores, which are finally
implemented in the last two patches. These exploit the fact that despite
the different kinds of FIDs and RIFs, they do share a common object on
which the core operations can operate on.
By hiding both objects from the rest of the driver and modeling their
operations using a VFT, it'll be easier to extend the driver for future
use cases such as VXLAN.
Tested using following LNST recipes:
https://github.com/jpirko/lnst/tree/master/recipes/switchdev
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mlxsw driver currently implements three types of RIFs. VLAN and FID
RIFs for L3 interfaces on top of VLAN-aware and VLAN-unaware bridges
(respectively) and Subport RIFs for all other L3 interfaces.
All the RIF types follow a common configuration procedure, which only
differs in the type-specific bits. The patch exploits this fact and
consolidates the common code paths, thereby simplifying the code and
making it more extensible.
This work also prepares the driver for use with future ASICs, where the
range of the Subport RIFs will be extended and their configuration
modified accordingly. By merely implementing a new RIF operations and
selecting it during initialization, the same driver could be re-used.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device supports three types of FIDs. 802.1Q and 802.1D FIDs for
VLAN-aware and VLAN-unaware bridges (respectively) and rFIDs to
transport packets to the router block.
The different users (e.g., bridge, router, ACLs) of the FIDs
infrastructure need not know about the internal FIDs implementation and
can therefore interact with it using a restricted set of exported
functions.
By encapsulating the entire FID logic and hiding it from the rest of the
driver we get a code base that it much simpler and easier to work with
and extend.
For example, in the current Spectrum ASIC only 802.1D FIDs can be
assigned a VNI, but future ASICs will also support 802.1Q FIDs. With
this patch in place, support for future ASICs can be easily added by
implementing a new FID operations according to their capabilities.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All RIF types are associated with a virtual router (VR), so determine VR
first when creating a RIF.
That way, we can more easily integrate the common RIF core in the
following patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a packet ingress the router but can't be assigned an ingress RIF,
it's dropped.
Therefore, in the case of RIF configured on top of a bridge, it makes
sense to start flooding broadcast packets to the router only after the
RIF was created.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that all the information to create a RIF is contained within the RIF
struct itself, we can also simplify the destruction logic.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All the information necessary for the configuration of RIFs can now be
found in the RIF struct itself, so reduce the arguments list.
This gets us one step closer to the common RIF core.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when a Subport RIF is configured, the LAG status and VLAN of
the underlying port are read from the port itself. This is problematic,
as we would like to have common code to configure all types of RIFs,
which aren't necessarily bound to a port.
Instead, embed the RIF in a struct specific to the Subport type, which
contains all the necessary information.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the following patches the RIF's configuration function is going to
expect a RIF struct with all the necessary information.
Therefore, allocate the RIF just before it's configured to the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following patches are going to re-arrange the FID and RIF code, so
that when the RIF is configured to the device based on the information
present in the RIF struct (which points to a FID).
For this reason, move the FID allocation to just before the RIF
configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As explained in the cover letter, since the introduction of the bridge
offload in the mlxsw driver, information related to the offloaded bridge
and bridge ports was stored in the individual port struct,
mlxsw_sp_port.
This lead to a bloated struct storing both physical properties of the
port (e.g., autoneg status) as well as logical properties of an upper
bridge port (e.g., learning, mrouter indication). While this might work
well for simple devices, it proved to be hard to extend when stacked
devices were taken into account and more advanced use-cases (e.g., IGMP
snooping) considered.
This patch removes the excess information from the above struct and
instead stores it in more appropriate structs that represent the bridge
port, the bridge itself and a VLAN configured on the bridge port.
The membership of a port in a bridge is denoted using the Port-VLAN
struct, which points to the bridge port and also member in the bridge
VLAN group of the VLAN it represents. This allows us to completely
remove the vPort abstraction and consolidate many of the code paths
relating to VLAN-aware and unaware bridges.
Note that the FID / vFID code is currently duplicated, but this will
soon go away when the common FID core will be introduced.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now we used to create FIDs upon the creation of VLAN uppers on
top of the VLAN-aware bridge. This was done so that in case a router
interface (RIF) was configured on top of the bridge, the FID would
already be there.
Instead, simplify the code and only create the FID upon RIF creation.
This is an intermediary step towards the introduction of the common FID
core, in which this code would be completely removed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when port netdevs (or their uppers) are enslaved to a bridge,
we simply propagate the CHANGEUPPER event all the way down and lose the
context of the actual netdevice used as the bridge port.
This leads to a lot of information hanging off the ports (and vPorts),
which doesn't logically belong there, such as mrouter indication and
unknown unicast flood state.
Following patches are going to put the mlxsw_sp_port struct on diet and
instead introduce a bridge port struct, where the above mentioned
information belongs. But in order to do that, we need to be able to
determine the bridge port netdevice, so propagate it down.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We're going to get rid of vPorts completely later in the patchset, but
the router code is self-contained, so it's a good candidate to start the
transition with.
Convert all the functions that expects to operate on a vPort to operate
on a Port-VLAN instead.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a vPort is destroyed, it leaves the FID it's currently mapped to
(if any) and drops the reference. The FID's leave function expects to
get the vPort as its argument, but this will have to change when the
vPort model is retired.
Change the function signature to expect a Port-VLAN struct instead and
patch the call sites accordingly.
The code introduced in this patch will be removed later in the patchset,
but this intermediary step is required in order to ease the code review.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is the first step in the transition from the vPort model to a
unified Port-VLAN structure. The new structure is defined and created /
destroyed upon invocation of the 8021q ndos, but it's not actually used
throughout the code.
Subsequent patches will initialize it correctly and also create /
destroy it upon switchdev's VLAN object.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently transition the port to "Virtual mode" upon the creation of
its first VLAN upper, as we need to classify incoming packets to a FID
using {Port, VID} and not only the VID.
However, it's more appropriate to transition the port to this mode when
the {Port, VID} are actually mapped to a FID. Either during the
enslavement of the VLAN upper to a VLAN-unaware bridge or the
configuration of a router port.
Do this change now in preparation for the introduction of the FID core,
where this operation will be encapsulated.
To prevent regressions, this patch also explicitly configures an OVS
slave to "Virtual mode". Otherwise, a packet that didn't hit an ACL rule
could be classified to an existing FID based on a global VID-to-FID
mapping, thus not incurring a FID mis-classification, which would
otherwise trap the packet to the CPU to be processed by the OVS daemon.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During enslavement to a bridge, after the CHANGEUPPER is sent, the
multicast enabled state of the bridge isn't propagated down to the
offloading driver unless it's changed.
This patch allows such drivers to query the multicast enabled state from
the bridge, so that they'll be able to correctly configure their flood
tables during port enslavement.
In case multicast is disabled, unregistered multicast packets can be
treated as broadcast and be flooded through all the bridge ports.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's useful for drivers supporting bridge offload to be able to query
the bridge's VLAN filtering state.
Currently, upon enslavement to a bridge master, the offloading driver
will only learn about the bridge's VLAN filtering state after the bridge
device was already linked with its slave.
Being able to query the bridge's VLAN filtering state allows such
drivers to forbid enslavement in case resource couldn't be allocated for
a VLAN-aware bridge and also choose the correct initialization routine
for the enslaved port, which is dependent on the bridge type.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull XFS fixes from Darrick Wong:
"A few miscellaneous bug fixes & cleanups:
- Fix indlen block reservation accounting bug when splitting delalloc
extent
- Fix warnings about unused variables that appeared in -rc1.
- Don't spew errors when bmapping a local format directory
- Fix an off-by-one error in a delalloc eof assertion
- Make fsmap only return inode information for CAP_SYS_ADMIN
- Fix a potential mount time deadlock recovering cow extents
- Fix unaligned memory access in _btree_visit_blocks
- Fix various SEEK_HOLE/SEEK_DATA bugs"
* tag 'xfs-4.12-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: Move handling of missing page into one place in xfs_find_get_desired_pgoff()
xfs: Fix off-by-in in loop termination in xfs_find_get_desired_pgoff()
xfs: Fix missed holes in SEEK_HOLE implementation
xfs: fix off-by-one on max nr_pages in xfs_find_get_desired_pgoff()
xfs: fix unaligned access in xfs_btree_visit_blocks
xfs: avoid mount-time deadlock in CoW extent recovery
xfs: only return detailed fsmap info if the caller has CAP_SYS_ADMIN
xfs: bad assertion for delalloc an extent that start at i_size
xfs: fix warnings about unused stack variables
xfs: BMAPX shouldn't barf on inline-format directories
xfs: fix indlen accounting error on partial delalloc conversion
|
|
Andrew Lunn says:
====================
net: dsa: mv88e6xxx: Add basic SERDES support
Some of the Marvell switches are SERDES interface, which must be
powered up before packets can be passed. This is particularly true on
the 6390, where the SERDES defaults to down, probably to save power.
This series refactors the existing SERDES support for the 6352, and
adds 6390 support.
v2:
Split phy functions out into phy.[ch]
Don't add MV88E6XXX_FLAG_G1_ATU_FID back again
Move the serdes op up in mv88e6xxx_ops
Move some #defines into serdes.h
Add a mv88e6xxx_serdes_power()
Don't keep moving calls to this helper around in the code
v3:
Move more phy functions into phy.[ch]
Make mv88e6xxx_phy_page_get() and mv88e6xxx_phy_page_put static
Use the mv88e6xxx_serdes_power() helper everywhere
dev_err(...) when mv88e6xxx_serdes_power() fails
Add reviewed-by's
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the port enable/disable callbacks, which enable/disable the
SERDES interfaces, if applicable. This should save a bit of
power/heat.
We also need to enable SERDES on CPU and DSA ports, so keep the
existing call to the op, but make it conditional.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6390X family has 8 SERDES lanes. These can be used for 2
10Gbps ports, ports 9 or 10. If these ports are used at slower speeds,
the SERDES lanes become available for other ports for 1000Base-X.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we use an op for SERDES operations, we don't need a flag for
it. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6390 family has a different SERDES implementation. Refactor
the mv88e6352 code into an ops function, so we can later add the
mv88e6390 code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The upcoming SERDES support will need to make use of PHY functions. Move
them out into a file of there own. No code changes.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrey Konovalov reported crashes in ipv4_mtu()
I could reproduce the issue with KASAN kernels, between
10.246.7.151 and 10.246.7.152 :
1) 20 concurrent netperf -t TCP_RR -H 10.246.7.152 -l 1000 &
2) At the same time run following loop :
while :
do
ip ro add 10.246.7.152 dev eth0 src 10.246.7.151 mtu 1500
ip ro del 10.246.7.152 dev eth0 src 10.246.7.151 mtu 1500
done
Cong Wang attempted to add back rt->fi in commit
82486aa6f1b9 ("ipv4: restore rt->fi for reference counting")
but this proved to add some issues that were complex to solve.
Instead, I suggested to add a refcount to the metrics themselves,
being a standalone object (in particular, no reference to other objects)
I tried to make this patch as small as possible to ease its backport,
instead of being super clean. Note that we believe that only ipv4 dst
need to take care of the metric refcount. But if this is wrong,
this patch adds the basic infrastructure to extend this to other
families.
Many thanks to Julian Anastasov for reviewing this patch, and Cong Wang
for his efforts on this problem.
Fixes: 2860583fe840 ("ipv4: Kill rt->fi")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of falling back to 00:00:00:00:00:00 generate a random address
if none is provided via platform data or from the device's register
space.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function ax_init_dev (which is called only from the driver's .probe
function) calls free_irq in the error path without having requested the
irq in the first place. So drop the free_irq call in the error path.
Fixes: 825a2ff1896e ("AX88796 network driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fix addresses two problems in the way the DSCP field is formulated
on the encapsulating header of IPv6 tunnels.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195661
1) The IPv6 tunneling code was manipulating the DSCP field of the
encapsulating packet using the 32b flowlabel. Since the flowlabel is
only the lower 20b it was incorrect to assume that the upper 12b
containing the DSCP and ECN fields would remain intact when formulating
the encapsulating header. This fix handles the 'inherit' and
'fixed-value' DSCP cases explicitly using the extant dsfield u8 variable.
2) The use of INET_ECN_encapsulate(0, dsfield) in ip6_tnl_xmit was
incorrect and resulted in the DSCP value always being set to 0.
Commit 90427ef5d2a4 ("ipv6: fix flow labels when the traffic class
is non-0") caused the regression by masking out the flowlabel
which exposed the incorrect handling of the DSCP portion of the
flowlabel in ip6_tunnel and ip6_gre.
Fixes: 90427ef5d2a4 ("ipv6: fix flow labels when the traffic class is non-0")
Signed-off-by: Peter Dawson <peter.a.dawson@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrew Lunn says:
====================
More marvell phy cleanups
This patchset continues the cleanup of the Marvell PHY driver. These
phys use pages to allow more than the 32 registers that fit into the
MDIO address space. Cleanup the code used for changing pages.
v2
Reverse christmas tree
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bring all the page names together, remove the repeats, and make them
uniform.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a common pattern of first reading the currently selected page
and then changing to another page. Add a helper to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
EXT_ADDR_PAGE is the same meaning as MII_MARVELL_PHY_PAGE, i.e. change
page. Replace it will calls to the helpers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace magic numbers for PHY pages with symbolic names.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
