summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2019-02-27arm64: dts: rockchip: move QCA6174A wakeup pin into its USB nodeBrian Norris3-30/+42
Currently, we don't coordinate BT USB activity with our handling of the BT out-of-band wake pin, and instead just use gpio-keys. That causes problems because we have no way of distinguishing wake activity due to a BT device (e.g., mouse) vs. the BT controller (e.g., re-configuring wake mask before suspend). This can cause spurious wake events just because we, for instance, try to reconfigure the host controller's event mask before suspending. We can avoid these synchronization problems by handling the BT wake pin directly in the btusb driver -- for all activity up until BT controller suspend(), we simply listen to normal USB activity (e.g., to know the difference between device and host activity); once we're really ready to suspend the host controller, there should be no more host activity, and only *then* do we unmask the GPIO interrupt. This is already supported by btusb; we just need to describe the wake pin in the right node. We list 2 compatible properties, since both PID/VID pairs show up on Scarlet devices, and they're both essentially identical QCA6174A-based modules. Also note that the polarity was wrong before: Qualcomm implemented WAKE as active high, not active low. We only got away with this because gpio-keys always reconfigured us as bi-directional edge-triggered. Finally, we have an external pull-up and a level-shifter on this line (we didn't notice Qualcomm's polarity in the initial design), so we can't do pull-down. Switch to pull-none. Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-27dt-bindings: net: btusb: add QCA6174A IDsBrian Norris1-0/+3
There are two USB PID/VID variations I've seen for this chip, and I want to utilize the 'interrupts' property defined here already. Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-27Bluetooth: btusb: add QCA6174A compatible propertiesBrian Norris1-0/+2
We may need to specify a GPIO wake pin for this device, so add a compatible property for it. There are at least to USB PID/VID variations of this chip: one with a Lite-On ID and one with an Atheros ID. Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-27Bluetooth: hci_qca: Use msleep() instead of open coding itMatthias Kaehlcke1-3/+1
Call msleep() in qca_set_baudrate() instead of reimplementing it. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-27Bluetooth: hci_qca: Add delay after power-off pulseMatthias Kaehlcke1-3/+3
During initialization the power-on pulse is currently sent inmediately after the prior power-off pulse. With this initialization often fails at boot time: [ 15.205224] Bluetooth: hci0: setting up wcn3990 [ 17.341062] Bluetooth: hci0: command 0xfc00 tx timeout [ 22.101453] ERROR: Bluetooth initialization failed [ 25.337740] Bluetooth: hci0: Reading QCA version information failed (-110) After a power-off pulse wait 10ms to give the controller time to power off. Remove the previous short settling delay, it isn't needed anymore. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-27Bluetooth: hci_qca: Move boot delay to qca_send_power_pulse()Matthias Kaehlcke1-3/+3
After sending a power on pulse the driver has a delay of 100ms to allow the host controller to boot. Move the delay into qca_send_power_pulse(), since it is directly related with the power-on pulse. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-27Bluetooth: hci_qca: Pass boolean 'on/off' to qca_send_power_pulse()Matthias Kaehlcke1-4/+5
There are only two types of power pulses 'on' or 'off', pass a boolean instead of the power pulse 'command'. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-26Bluetooth: hci_qca: Set HCI_QUIRK_USE_BDADDR_PROPERTY for wcn3990Matthias Kaehlcke1-0/+1
Set quirk for wcn3990 to read BD_ADDR from a firmware node property. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Tested-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-26Bluetooth: btqcomsmd: use HCI_QUIRK_USE_BDADDR_PROPERTYMatthias Kaehlcke1-28/+3
Use the HCI_QUIRK_USE_BDADDR_PROPERTY quirk to let the HCI core handle the reading of 'local-bd-address'. With this there is no need to set HCI_QUIRK_INVALID_BDADDR, the case of a non-existing or invalid fwnode property is handled by the core code. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-26Bluetooth: Add quirk for reading BD_ADDR from fwnode propertyMatthias Kaehlcke3-2/+59
Add HCI_QUIRK_USE_BDADDR_PROPERTY to allow controllers to retrieve the public Bluetooth address from the firmware node property 'local-bd-address'. If quirk is set and the property does not exist or is invalid the controller is marked as unconfigured. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> Tested-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-26Bluetooth: hci_ldisc: Postpone HCI_UART_PROTO_READY bit set in ↵Kefeng Wang1-2/+1
hci_uart_set_proto() task A: task B: hci_uart_set_proto flush_to_ldisc - p->open(hu) -> h5_open //alloc h5 - receive_buf - set_bit HCI_UART_PROTO_READY - tty_port_default_receive_buf - hci_uart_register_dev - tty_ldisc_receive_buf - hci_uart_tty_receive - test_bit HCI_UART_PROTO_READY - h5_recv - clear_bit HCI_UART_PROTO_READY while() { - p->open(hu) -> h5_close //free h5 - h5_rx_3wire_hdr - h5_reset() //use-after-free } It could use ioctl to set hci uart proto, but there is a use-after-free issue when hci_uart_register_dev() fail in hci_uart_set_proto(), see stack above, fix this by setting HCI_UART_PROTO_READY bit only when hci_uart_register_dev() return success. Reported-by: syzbot+899a33dc0fa0dbaf06a6@syzkaller.appspotmail.com Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reviewed-by: Jeremy Cline <jcline@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-26Bluetooth: mgmt: Use struct_size() helperGustavo A. R. Silva1-5/+3
Make use of the struct_size() helper instead of an open-coded version in order to avoid any potential type mistakes, in particular in the context in which this code is being used. So, change the following form: sizeof(*rp) + (sizeof(rp->entry[0]) * count); to : struct_size(rp, entry, count) Notice that, in this case, variable rp_len is not necessary, hence it is removed. This code was detected with the help of Coccinelle. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-25net: wan: z85230: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop ↵Yang Wei1-1/+1
profiles dev_consume_skb_irq() should be called in z8530_tx_done() when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: wan: cosa: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop ↵Yang Wei1-1/+1
profiles dev_consume_skb_irq() should be called in cosa_net_tx_done() when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: wan: sbni: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop ↵Yang Wei1-1/+1
profiles dev_consume_skb_irq() should be called in send_complete() when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: wan: ixp4xx_hss: replace dev_kfree_skb_irq by dev_consume_skb_irq for ↵Yang Wei1-1/+1
drop profiles dev_consume_skb_irq() should be called in hss_hdlc_txdone_irq() when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: wan: wanxl: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop ↵Yang Wei1-1/+1
profiles dev_consume_skb_irq() should be called in wanxl_tx_intr() when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: lmc: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profilesYang Wei1-2/+1
dev_consume_skb_irq() should be called in lmc_interrupt() when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Delete a redundant comment line in lmc_interrupt(). Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25Merge branch 'pie-next'David S. Miller2-43/+66
Leslie Monis says: ==================== net: sched: pie: align PIE implementation with RFC 8033 The current implementation of the PIE queuing discipline is according to the IETF draft [http://tools.ietf.org/html/draft-pan-aqm-pie-00] and the paper [PIE: A Lightweight Control Scheme to Address the Bufferbloat Problem]. However, a lot of necessary modifications and enhancements have been proposed in RFC 8033, which have not yet been incorporated in the source code of Linux. This patch series helps in achieving the same. Performance tests carried out using Flent [https://flent.org/] Changes from v2 to v3: - Used div_u64() instead of direct division after explicit type casting as recommended by David Changes from v1 to v2: - Excluded the patch setting PIE dynamically active/inactive as the test results were unsatisfactory - Fixed a scaling issue when adding more auto-tuning cases which caused local variables to underflow - Changed the long if/else chain to a loop as suggested by Stephen - Changed the position of the accu_prob variable in the pie_vars structure as recommended by Stephen ==================== Acked-by: Dave Taht <dave.taht@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: sched: pie: update referencesMohit P. Tahiliani1-3/+1
RFC 8033 replaces the IETF draft for PIE Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in> Signed-off-by: Dhaval Khandla <dhavaljkhandla26@gmail.com> Signed-off-by: Hrishikesh Hiraskar <hrishihiraskar@gmail.com> Signed-off-by: Manish Kumar B <bmanish15597@gmail.com> Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com> Signed-off-by: Leslie Monis <lesliemonis@gmail.com> Acked-by: Dave Taht <dave.taht@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: sched: pie: add derandomization mechanismMohit P. Tahiliani1-1/+27
Random dropping of packets to achieve latency control may introduce outlier situations where packets are dropped too close to each other or too far from each other. This can cause the real drop percentage to temporarily deviate from the intended drop probability. In certain scenarios, such as a small number of simultaneous TCP flows, these deviations can cause significant deviations in link utilization and queuing latency. RFC 8033 suggests using a derandomization mechanism to avoid these deviations. Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in> Signed-off-by: Dhaval Khandla <dhavaljkhandla26@gmail.com> Signed-off-by: Hrishikesh Hiraskar <hrishihiraskar@gmail.com> Signed-off-by: Manish Kumar B <bmanish15597@gmail.com> Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com> Signed-off-by: Leslie Monis <lesliemonis@gmail.com> Acked-by: Dave Taht <dave.taht@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: sched: pie: add more cases to auto-tune alpha and betaMohit P. Tahiliani2-34/+33
The current implementation scales the local alpha and beta variables in the calculate_probability function by the same amount for all values of drop probability below 1%. RFC 8033 suggests using additional cases for auto-tuning alpha and beta when the drop probability is less than 1%. In order to add more auto-tuning cases, MAX_PROB must be scaled by u64 instead of u32 to prevent underflow when scaling the local alpha and beta variables in the calculate_probability function. Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in> Signed-off-by: Dhaval Khandla <dhavaljkhandla26@gmail.com> Signed-off-by: Hrishikesh Hiraskar <hrishihiraskar@gmail.com> Signed-off-by: Manish Kumar B <bmanish15597@gmail.com> Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com> Signed-off-by: Leslie Monis <lesliemonis@gmail.com> Acked-by: Dave Taht <dave.taht@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: sched: pie: change initial value of pie_vars->burst_timeMohit P. Tahiliani1-2/+2
RFC 8033 suggests an initial value of 150 milliseconds for the maximum time allowed for a burst of packets. Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in> Signed-off-by: Dhaval Khandla <dhavaljkhandla26@gmail.com> Signed-off-by: Hrishikesh Hiraskar <hrishihiraskar@gmail.com> Signed-off-by: Manish Kumar B <bmanish15597@gmail.com> Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com> Signed-off-by: Leslie Monis <lesliemonis@gmail.com> Acked-by: Dave Taht <dave.taht@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: sched: pie: change default value of pie_params->tupdateMohit P. Tahiliani1-1/+1
RFC 8033 suggests a default value of 15 milliseconds for the update interval. Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in> Signed-off-by: Dhaval Khandla <dhavaljkhandla26@gmail.com> Signed-off-by: Hrishikesh Hiraskar <hrishihiraskar@gmail.com> Signed-off-by: Manish Kumar B <bmanish15597@gmail.com> Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com> Signed-off-by: Leslie Monis <lesliemonis@gmail.com> Acked-by: Dave Taht <dave.taht@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: sched: pie: change default value of pie_params->targetMohit P. Tahiliani1-1/+1
RFC 8033 suggests a default value of 15 milliseconds for the target queue delay. Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in> Signed-off-by: Dhaval Khandla <dhavaljkhandla26@gmail.com> Signed-off-by: Hrishikesh Hiraskar <hrishihiraskar@gmail.com> Signed-off-by: Manish Kumar B <bmanish15597@gmail.com> Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com> Signed-off-by: Leslie Monis <lesliemonis@gmail.com> Acked-by: Dave Taht <dave.taht@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: sched: pie: change value of QUEUE_THRESHOLDMohit P. Tahiliani1-1/+1
RFC 8033 recommends a value of 16384 bytes for the queue threshold. Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in> Signed-off-by: Dhaval Khandla <dhavaljkhandla26@gmail.com> Signed-off-by: Hrishikesh Hiraskar <hrishihiraskar@gmail.com> Signed-off-by: Manish Kumar B <bmanish15597@gmail.com> Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com> Signed-off-by: Leslie Monis <lesliemonis@gmail.com> Acked-by: Dave Taht <dave.taht@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25mlxsw: spectrum: acl: Use struct_size() in kzalloc()Gustavo A. R. Silva1-4/+2
One of the more common cases of allocation size calculations is finding the size of a structure that has a zero-sized array at the end, along with memory for some number of elements for that array. For example: struct foo { int stuff; struct boo entry[]; }; size = sizeof(struct foo) + count * sizeof(struct boo); instance = kzalloc(size, GFP_KERNEL) Instead of leaving these open-coded and prone to type mistakes, we can now use the new struct_size() helper: instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL) Notice that, in this case, variable alloc_size is not necessary, hence it is removed. This code was detected with the help of Coccinelle. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25Merge branch 'aquantia-hwmon'David S. Miller4-0/+274
Heiner Kallweit says: ==================== net: phy: aquantia: add hwmon support This series adds HWMON support for the temperature sensor and the related alarms on the 107/108/109 chips. v2: - remove struct aqr_priv - rename header file to aquantia.h v3: - add conditional compiling of aquantia_hwmon.c - improve converting sensor register values to/from long - add helper aqr_hwmon_test_bit ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: phy: aquantia: add hwmon supportHeiner Kallweit4-0/+273
This adds HWMON support for the temperature sensor and the related alarms on the 107/108/109 chips. This patch is based on work from Nikita and Andrew. I added: - support for changing alarm thresholds via sysfs - move HWMON code to a separate source file to improve maintainability - smaller changes like using IS_REACHABLE instead of ifdef (avoids problems if PHY driver is built in and HWMON is a module) v2: - remove struct aqr_priv - rename header file to aquantia.h v3: - add conditional compiling of aquantia_hwmon.c - improve converting sensor register values to/from long - add helper aqr_hwmon_test_bit Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: phy: aquantia: rename aquantia.c to aquantia_main.cHeiner Kallweit2-0/+1
Rename aquantia.c to aquantia_main.c to be prepared for adding new functionality to separate source code files. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25Merge branch '100GbE' of ↵David S. Miller12-199/+364
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue Jeff Kirsher says: ==================== 100GbE Intel Wired LAN Driver Updates 2019-02-22 This series contains updates to the ice driver only. Bruce adds the __always_unused attribute to a parameter to avoid compiler warnings when using -Wunused-parameter. Fixed unnecessary type-casting and the use of sizeof(). Fix the allocation of structs that have become memory hogs, so allocate them in heaps and fix all the associated references. Fixed the "possible" numeric overflow issues that were caught with static analysis. Maciej fixes the maximum MTU calculation by taking into account double VLAN tagging amd ensure that the operations are done in the correct order. Victor fixes the supported node calculation, where we were not taking into account if there is space to add the new VSI or intermediate node above that layer, then it is not required to continue the calculation. Added a check for a leaf node presence for a given VSI, which is needed before removing a VSI. Jake fixes an issue where the VSI list is shared, so simply removing a VSI from the list will cause issues for the other users who reference the list. Since we also free the memory, this could lead to segmentation faults. Brett fixes an issue where driver unload could cause a system reboot when intel_iommu=on parameter is set. The issue is that we are not clearing the CAUSE_ENA bit for the appropriate control queues register when freeing the miscellaneous interrupt vector. Mitch is so kind, he prevented spamming the VF with link messages when the link status really has not changed. Updates the driver to use the absolute vector ID and not the per-PF vector ID for the VF MSIx vector allocation. Lukasz fixes the ethtool pause parameter for the ice driver, which was originally based off the link status but is now based off the PHY configuration. This is to resolve an issue where pause parameters could be set while link was down. Jesse updates the string that reports statistics so the string does not get modified at runtime and cause reports of string truncation. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: sched: don't release block->lock when dumping chainsVlad Buslov1-9/+7
Function tc_dump_chain() obtains and releases block->lock on each iteration of its inner loop that dumps all chains on block. Outputting chain template info is fast operation so locking/unlocking mutex multiple times is an overhead when lock is highly contested. Modify tc_dump_chain() to only obtain block->lock once and dump all chains without releasing it. Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Suggested-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: sched: set dedicated tcf_walker flag when tp is emptyVlad Buslov2-4/+10
Using tcf_walker->stop flag to determine when tcf_walker->fn() was called at least once is unreliable. Some classifiers set 'stop' flag on error before calling walker callback, other classifiers used to call it with NULL filter pointer when empty. In order to prevent further regressions, extend tcf_walker structure with dedicated 'nonempty' flag. Set this flag in tcf_walker->fn() implementation that is used to check if classifier has filters configured. Fixes: 8b64678e0af8 ("net: sched: refactor tp insert/delete for concurrent execution") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Suggested-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: dsa: mv88e6xxx: Fix phylink_validate for Topaz familyMarek Behún1-2/+16
The Topaz family should have different phylink_validate method from the Peridot, since on Topaz the port supporting 2500BaseX mode is port 5, not 9 and 10. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25net: dsa: mv88e6xxx: Default CMODE to 1000BaseX only on 6390XMarek Behún1-0/+2
Commit 787799a9d555 sets the SERDES interfaces of 6390 and 6390X to 1000BaseX, but this is only needed on 6390X, since there are SERDES interfaces which can be used on lower ports on 6390. This commit fixes this by returning to previous behaviour on 6390. (Previous behaviour means that CMODE is not set at all if requested mode is NA). This is needed on Turris MOX, where the 88e6190 is connected to CPU in 2500BaseX mode. Fixes: 787799a9d555 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX") Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25tcp: clean up SOCK_DEBUG()Yafang Shao2-20/+1
Per discussion with Daniel[1] and Eric[2], these SOCK_DEBUG() calles in TCP are not needed now. We'd better clean up it. [1] https://patchwork.ozlabs.org/patch/1035573/ [2] https://patchwork.ozlabs.org/patch/1040533/ Signed-off-by: Yafang Shao <laoar.shao@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25tcp: remove unused parameter of tcp_sacktag_bsearch()Taehee Yoo1-10/+6
parameter state in the tcp_sacktag_bsearch() is not used. So, it can be removed. Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25ice: fix overlong string, update stats outputJesse Brandeburg1-40/+40
A test started warning on a string truncation. This led to an unfortunate realization that we are likely not accounting for the stats length correctly before this patch, so fix the issue by putting "port." in front of all the PF stats, instead of magically prepending it at runtime. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-02-25ice: Fix for FC get rx/tx pause paramsLukasz Czapnik1-11/+26
Ethtool reported pause params based on the currently negotiated link settings instead of current PHY config. User was not able to turn off pause params because ethtool was incorrectly reporting parameters as off when link was down even though PHY was configured to support pause frames. Now pause params are taken from PHY config instead of link status. Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-02-25ice: use absolute vector ID for VFsMitch Williams1-2/+4
When the PF driver sets up the VF MSI-X vector allocation, it needs to use the hardware absolute vector ID, not the per-PF vector ID. Without this change we see (apparent) TX hangs when using VFs on multiple PFs. Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-02-25ice: check for a leaf node presenceVictor Raj2-0/+24
Check for a leaf node presence for a given VSI. This check is required before removing a VSI since VSIs can't be removed with enabled queues (with leaf nodes) from the FW scheduler tree unless its a reset. Signed-off-by: Victor Raj <victor.raj@intel.com> Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-02-25ice: flush Tx pipe on disable queue timeoutVictor Raj1-2/+19
Set the flush Tx pipe flag instead of getting an EAGAIN error when FW times out in processing the disable Tx queue command. Signed-off-by: Victor Raj <victor.raj@intel.com> Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-02-25ice: clear VF ARQLEN register on resetMitch Williams2-0/+6
On older devices like X710 and X722, the VF's ARQLEN register is cleared on reset, so the VF driver uses that register to detect an unannounced reset. Unfortunately, on devices controlled by ice, this register is NOT cleared on reset. This causes the VF to miss resets, and even on properly-announced resets, the VF driver complains that it didn't see the reset. To fix this, we'll do it in software. When we handle a VF reset (whether triggered by software or VFLR), clear this register after the HW reset is complete. Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-02-25ice: don't spam VFs with link messagesMitch Williams1-1/+2
Don't send a link message to the VFs unless link actually changes state. This avoids a small timing hole in some VF drivers that can cause an apparent TX hang if they receive a link status message at the wrong time. Although we have fixed the timing hole in the current VF driver, there are still lots of drivers in the field that have this timing hole. Let's not fall into it if we can avoid it. Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-02-25ice: only use the VF for ICE_VSI_VF in ice_vsi_releaseBrett Creeley1-2/+4
In ice_vsi_release we are always assigning a value to the local VF variable. Change this to only be assigned if the VSI is a VF VSI. Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-02-25ice: fix numeric overflow warningBruce Allan2-4/+5
When compiling and analyzing the driver on newer kernels, a static analyzer warns about the following "numeric overflow" issues: "The result of expression: 'budget-1' generates 4-byte type while casting to a bigger size of 8-byte". "The result of expression: '*words-words_read' generates 4-byte type while casting to a bigger size of 8-byte". Fix them both. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-02-25ice: fix issue where host reboots on unload when iommu=onBrett Creeley1-17/+54
Currently if the kernel has the intel_iommu=on parameter set, on some platforms removing the driver causes a system reboot. In initialization we associate the control queue interrupts with the pf->hw_oicr_idx and enable the interrupts by setting the CAUSE_ENA bit. The problem comes on teardown because we are not clearing the CAUSE_ENA bit for the control queues, but the vector at pf->hw_oicr_idx (miscellaneous interrupt vector) gets disabled. Fix this by clearing the CAUSE_ENA bit in the appropriate control queue registers on when freeing the miscellaneous interrupt vector. Also, move the call to ice_free_irq_msix_misc() to after ice_deinit_sw() in ice_remove() because ice_deinit_sw() makes an AQ call, but ice_free_irq_msix_misc() disables the miscellaneous vector and it's associated interrupts. Also, create two small helper functions to enable and disable the control queue interrupts respectively. Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-02-25ice: fix ice_remove_rule_internal vsi_list handlingJacob Keller1-2/+13
When adding multiple VLANs to the same VSI, the ice_add_vlan code will share the VSI list, so as not to create multiple unnecessary VSI lists. Consider the following flow ice_add_vlan(hw, <VSI 0 VID 7, VSI 0 VID 8, VSI 0 VID 9>) Where we add three VLAN filters for VIDs 7, 8, and 9, all for VSI 0. The ice_add_vlan will create a single vsi_list and share it among all the filters. Later, if we try to remove a VLAN, ice_remove_vlan(hw, <VSI 0 VID 7>) Then the removal code will update the vsi_list and remove VSI 0 from it. But, since the vsi_list is shared, this breaks the list for the other users who reference it. We actually even free the VSI list memory, and may result in segmentation faults. This is due to the way that VLAN rule share VSI lists with reference counts, and is caused because we call ice_rem_update_vsi_list even when the ref_cnt is greater than one. To fix this, handle the case where ref_cnt is greater than one separately. In this case, we need to remove the associated rule without modifying the vsi_list, since it is currently being referenced by another rule. Instead, we just need to decrement the VSI list ref_cnt. The case for handling sharing of VSI lists with multiple VSIs is not currently supported by this code. No such rules will be created today, and this code will require changes if/when such code is added. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-02-25ice: fix stack hogs from struct ice_vsi_ctx structuresBruce Allan3-67/+117
struct ice_vsi_ctx has gotten large enough that function local declarations of it on the stack are causing stack hogs. Fix that by allocating the structs on heap. Cleanup some formatting issues in the code around these changes and fix incorrect data type uses of returned functions in a couple places. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-02-25ice: sizeof(<type>) should be avoidedBruce Allan6-45/+38
With sizeof(), it is preferable to use the variable of type <type> instead of sizeof(<type>). There are multiple places where a temporary variable is used to hold a 'size' value which is then used for a subsequent alloc/memset. Get rid of the temporary variable by calculating size as part of the alloc/memset statement. Also remove unnecessary type-cast. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-18 06:32:55 +0000