| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This kernel cycle was quite calm when it comes to pin control and
there is really just one major change, and that is the introduction of
devm_pinctrl_register() managed resources.
Apart from that linear development, details below.
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable
drivers to use it, saving lots of lines of code all over the place.
New drivers:
- driver for the Broadcom NS2 SoC
- subdriver for the PXA25x SoCs
- subdriver for the AMLogic Meson GXBB SoC
Driver improvements:
- the Intel Baytrail driver now properly supports pin control
- Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction()
callback in the GPIO portions
- continued development and stabilization of several SH-PFC SoC
subdrivers: r8a7795, r8a7790, r8a7794 etc"
* tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits)
Revert "pinctrl: tegra: avoid parked_reg and parked_bank"
pinctrl: meson: Fix eth_tx_en bit index
pinctrl: tegra: avoid parked_reg and parked_bank
pinctrl: tegra: Correctly check the supported configuration
pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC
pinctrl: rockchip: fix pull setting error for rk3399
pinctrl: stm32: Implement .pin_config_dbg_show()
pinctrl: nomadik: hide nmk_gpio_get_mode when unused
pinctrl: ns2: rename pinctrl_utils_dt_free_map
pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable
pinctrl: at91: Make at91_gpio_template const
pinctrl: baytrail: fix some error handling in debugfs
pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC
pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged
pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove()
pinctrl: nomadik: implement .get_direction()
pinctrl: nomadik: use BIT() with offsets consequently
pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range
pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration
pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration
...
|
|
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-kconfig
Pull localmodconfig updates from Steven Rostedt.
"Benjamin Poirier added some minor fixes and clean ups to
localmodconfig.
One is a fix for making sure that module signing still works when
coming from a different environment. If original keys are not found
it will warn and reset the keys to their default value"
* tag 'localmodconfig-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-kconfig:
localmodconfig: Fix whitespace repeat count after "tristate"
localmodconfig: Reset certificate paths
localmodconfig: Add missing $ to reference a variable
localmodconfig: Fix parsing of "help" text
localmodconfig: Recognize more keywords that end a menu entry
localmodconfig: Fix parsing of Kconfig "source" statements
|
|
Pull KVM updates from Paolo Bonzini:
"Small release overall.
x86:
- miscellaneous fixes
- AVIC support (local APIC virtualization, AMD version)
s390:
- polling for interrupts after a VCPU goes to halted state is now
enabled for s390
- use hardware provided information about facility bits that do not
need any hypervisor activity, and other fixes for cpu models and
facilities
- improve perf output
- floating interrupt controller improvements.
MIPS:
- miscellaneous fixes
PPC:
- bugfixes only
ARM:
- 16K page size support
- generic firmware probing layer for timer and GIC
Christoffer Dall (KVM-ARM maintainer) says:
"There are a few changes in this pull request touching things
outside KVM, but they should all carry the necessary acks and it
made the merge process much easier to do it this way."
though actually the irqchip maintainers' acks didn't make it into the
patches. Marc Zyngier, who is both irqchip and KVM-ARM maintainer,
later acked at http://mid.gmane.org/573351D1.4060303@arm.com ('more
formally and for documentation purposes')"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (82 commits)
KVM: MTRR: remove MSR 0x2f8
KVM: x86: make hwapic_isr_update and hwapic_irr_update look the same
svm: Manage vcpu load/unload when enable AVIC
svm: Do not intercept CR8 when enable AVIC
svm: Do not expose x2APIC when enable AVIC
KVM: x86: Introducing kvm_x86_ops.apicv_post_state_restore
svm: Add VMEXIT handlers for AVIC
svm: Add interrupt injection via AVIC
KVM: x86: Detect and Initialize AVIC support
svm: Introduce new AVIC VMCB registers
KVM: split kvm_vcpu_wake_up from kvm_vcpu_kick
KVM: x86: Introducing kvm_x86_ops VCPU blocking/unblocking hooks
KVM: x86: Introducing kvm_x86_ops VM init/destroy hooks
KVM: x86: Rename kvm_apic_get_reg to kvm_lapic_get_reg
KVM: x86: Misc LAPIC changes to expose helper functions
KVM: shrink halt polling even more for invalid wakeups
KVM: s390: set halt polling to 80 microseconds
KVM: halt_polling: provide a way to qualify wakeups during poll
KVM: PPC: Book3S HV: Re-enable XICS fast path for irqfd-generated interrupts
kvm: Conditionally register IRQ bypass consumer
...
|
|
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"We have a relatively big changeset for ARC for 4.7.
The highlight is support for EZChip (now Mellanox) NPS-400 network
processor, a 400-Gb throughput C-programmable packet processor based
on ARC700 cores from Synopsys. See
http://www.mellanox.com/related-docs/prod_npu/PB_NPS-400.pdf
Also present are irqchip and clocksource drivers for NPS as agreed
with respective maintainers to go via ARC tree due to an soc header
dependency. I have the needed ACKs from Jason, Marc, Daniel. You
might run into a trivial merge conflict in drivers/irqchip/*
This EZChip platform support required some deep changes in ARC
architecture code and also opportunity to cleanup past sins (legacy
irq domains, missing irq domain lookup, hard coded timer irqs...)
Summary:
- Support for EZChip (now Mellanox) NPS-400 Network processor based
on ARC700
- NPS interrupt controller and clocksource drivers
- ARC timers probed off DT
- ARC iqrchips switching to linear domain (upgrade from legacy
domains)"
* tag 'arc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (37 commits)
arc: axs103_smp: Fix CPU frequency to 100MHz for dual-core
arc: axs10x: Add DT bindings for I2S PLL Clock
ARC: pae: STRICT_MM_TYPECHECKS was broken
ARC: Add eznps platform to Kconfig and Makefile
ARC: [plat-eznps] Use dedicated COMMAND_LINE_SIZE
ARC: [plat-eznps] Use dedicated cpu_relax()
ARC: [plat-eznps] Use dedicated identity auxiliary register.
ARC: [plat-eznps] Use dedicated SMP barriers
ARC: [plat-eznps] Use dedicated atomic/bitops/cmpxchg
ARC: [plat-eznps] Use dedicated user stack top
ARC: [plat-eznps] Add eznps platform
ARC: [plat-eznps] Add eznps board defconfig and dts
ARC: Mark secondary cpu online only after all HW setup is done
ARC: rwlock: disable interrupts in !LLSC variant
ARC: Make vmalloc size configurable
ARC: clean out UAPI byteorder.h clean off Kconfig symbol
irqchip: add nps Internal and external irqchips
clocksource: Add NPS400 timers driver
soc: Support for EZchip SoC
Documentation: Add EZchip vendor to binding list
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem updates from James Morris:
"Highlights:
- A new LSM, "LoadPin", from Kees Cook is added, which allows forcing
of modules and firmware to be loaded from a specific device (this
is from ChromeOS, where the device as a whole is verified
cryptographically via dm-verity).
This is disabled by default but can be configured to be enabled by
default (don't do this if you don't know what you're doing).
- Keys: allow authentication data to be stored in an asymmetric key.
Lots of general fixes and updates.
- SELinux: add restrictions for loading of kernel modules via
finit_module(). Distinguish non-init user namespace capability
checks. Apply execstack check on thread stacks"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (48 commits)
LSM: LoadPin: provide enablement CONFIG
Yama: use atomic allocations when reporting
seccomp: Fix comment typo
ima: add support for creating files using the mknodat syscall
ima: fix ima_inode_post_setattr
vfs: forbid write access when reading a file into memory
fs: fix over-zealous use of "const"
selinux: apply execstack check on thread stacks
selinux: distinguish non-init user namespace capability checks
LSM: LoadPin for kernel file loading restrictions
fs: define a string representation of the kernel_read_file_id enumeration
Yama: consolidate error reporting
string_helpers: add kstrdup_quotable_file
string_helpers: add kstrdup_quotable_cmdline
string_helpers: add kstrdup_quotable
selinux: check ss_initialized before revalidating an inode label
selinux: delay inode label lookup as long as possible
selinux: don't revalidate an inode's label when explicitly setting it
selinux: Change bool variable name to index.
KEYS: Add KEYCTL_DH_COMPUTE command
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This includes two new updates for the ftrace infrastructure.
- With the changing of the code for filtering events by pid, from a
list of pids to a bitmask, we can now easily implement following
forks. With a new tracing option "event-fork" which, when set,
will have tasks with pids in set_event_pid, when they fork, to have
their child pids added to set_event_pid and the child will be
traced as well.
Note, if "event-fork" is set and a task with its pid in
set_event_pid exits, its pid will be removed from set_event_pid
- The addition of Tom Zanussi's hist triggers. This includes a very
thorough documentatino on how to use the hist triggers with events.
This introduces a quick and easy way to get histogram data from
events and their fields.
Some other cleanups and updates were added as well. Like Masami
Hiramatsu added test cases for the event trigger and hist triggers.
Also I added a speed up of filtering by using a temp buffer when
filters are set"
* tag 'trace-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (45 commits)
tracing: Use temp buffer when filtering events
tracing: Remove TRACE_EVENT_FL_USE_CALL_FILTER logic
tracing: Remove unused function trace_current_buffer_lock_reserve()
tracing: Remove one use of trace_current_buffer_lock_reserve()
tracing: Have trace_buffer_unlock_commit() call the _regs version with NULL
tracing: Remove unused function trace_current_buffer_discard_commit()
tracing: Move trace_buffer_unlock_commit{_regs}() to local header
tracing: Fold filter_check_discard() into its only user
tracing: Make filter_check_discard() local
tracing: Move event_trigger_unlock_commit{_regs}() to local header
tracing: Don't use the address of the buffer array name in copy_from_user
tracing: Handle tracing_map_alloc_elts() error path correctly
tracing: Add check for NULL event field when creating hist field
tracing: checking for NULL instead of IS_ERR()
tracing: Do not inherit event-fork option for instances
tracing: Fix unsigned comparison to zero in hist trigger code
kselftests/ftrace: Add a test for log2 modifier of hist trigger
tracing: Add hist trigger 'log2' modifier
kselftests/ftrace: Add hist trigger testcases
kselftests/ftrace : Add event trigger testcases
...
|
|
Pull audit updates from Paul Moore:
"Four small audit patches for 4.7.
Two are simple cleanups around the audit thread management code, one
adds a tty field to AUDIT_LOGIN events, and the final patch makes
tty_name() usable regardless of CONFIG_TTY.
Nothing controversial, and it all passes our regression test"
* 'stable-4.7' of git://git.infradead.org/users/pcmoore/audit:
tty: provide tty_name() even without CONFIG_TTY
audit: add tty field to LOGIN event
audit: we don't need to __set_current_state(TASK_RUNNING)
audit: cleanup prune_tree_thread
|
|
Pull remoteproc updates from Bjorn Andersson:
"Introduce a synchronization point between the async firmware loading
and clients requesting the remote processor to boot, as well as
support for remote processors that are not interested in the resource
table information"
* tag 'rproc-v4.7' of git://github.com/andersson/remoteproc:
remoteproc: Add additional crash reasons
remoteproc: core: Make the loaded resource table optional
remoteproc: core: Task sync during rproc_fw_boot()
|
|
Pull rpmsg updates from Bjorn Andersson:
"Refactor rpmsg module registration to follow other subsystems; by
introduction of module_rpmsg_driver and hiding of THIS_MODULE from
clients"
* tag 'rpmsg-v4.7' of git://github.com/andersson/remoteproc:
rpmsg: use module_rpmsg_driver in existing drivers and examples
rpmsg: add helper macro module_rpmsg_driver
rpmsg: drop owner assignment from rpmsg_drivers
rpmsg: add THIS_MODULE to rpmsg_driver in rpmsg core
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"First round of updates for the input subsystem. No new drivers here,
just some driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: rotary-encoder - fix bare use of 'unsigned'
Input: cm109 - spin_lock in complete() cleanup
Input: cm109 - fix handling of volume and mute buttons
Input: byd - don't wipe dynamically allocated memory twice
Input: twl4030 - fix unsafe macro definition
Input: twl6040-vibra - remove mutex
Input: bcm_iproc_tsc - DT spelling s/clock-name/clock-names/
Input: bcm_iproc_tsc - use syscon to access shared registers
Input: ti_am335x_tsc - use SIMPLE_DEV_PM_OPS
Input: omap-keypad - remove set_col_gpio_val() and get_row_gpio_val()
Input: omap-keypad - drop empty PM stubs
Input: omap-keypad - remove adjusting of scan delay
Input: gpio-keys - clean up device tree binding example
Input: kbtab - stop saving struct usb_device
Input: gtco - stop saving struct usb_device
Input: aiptek - stop saving struct usb_device
Input: acecad - stop saving struct usb_device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- added support for Intersil/Techwell TW686x-based video capture cards
- v4l PCI skeleton driver moved to samples directory
- Documentation cleanups and improvements
- RC: reduced the memory footprint for IR raw events
- tpg: Export the tpg code from vivid as a module
- adv7180: Add device tree binding documentation
- lots of driver improvements and fixes
* tag 'media/v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (173 commits)
[media] exynos-gsc: avoid build warning without CONFIG_OF
[media] samples: v4l: from Documentation to samples directory
[media] dib0700: add USB ID for another STK8096-PVR ref design based card
[media] tvp5150: propagate I2C write error in .s_register callback
[media] tvp5150: return I2C write operation failure to callers
[media] em28xx: add support for Hauppauge WinTV-dualHD DVB tuner
[media] em28xx: add missing USB IDs
[media] update cx23885 and em28xx cardlists
[media] media: au0828 fix au0828_v4l2_device_register() to not unlock and free
[media] c8sectpfe: Rework firmware loading mechanism
[media] c8sectpfe: Demote print to dev_dbg
[media] c8sectpfe: Fix broken circular buffer wp management
[media] media-device: Simplify compat32 logic
[media] media: i2c: ths7303: remove redundant assignment on bt
[media] dvb-usb: hide unused functions
[media] xilinx-vipp: remove unnecessary of_node_put
[media] drivers/media/media-devnode: clear private_data before put_device()
[media] drivers/media/media-device: move debug log before _devnode_unregister()
[media] drivers/media/rc: postpone kfree(rc_dev)
[media] media/dvb-core: forward media_create_pad_links() return value
...
|
|
Pull SCSI updates from James Bottomley:
"First round of SCSI updates for the 4.6+ merge window.
This batch includes the usual quota of driver updates (bnx2fc, mp3sas,
hpsa, ncr5380, lpfc, hisi_sas, snic, aacraid, megaraid_sas). There's
also a multiqueue update for scsi_debug, assorted bug fixes and a few
other minor updates (refactor of scsi_sg_pools into generic code, alua
and VPD updates, and struct timeval conversions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (138 commits)
mpt3sas: Used "synchronize_irq()"API to synchronize timed-out IO & TMs
mpt3sas: Set maximum transfer length per IO to 4MB for VDs
mpt3sas: Updating mpt3sas driver version to 13.100.00.00
mpt3sas: Fix initial Reference tag field for 4K PI drives.
mpt3sas: Handle active cable exception event
mpt3sas: Update MPI header to 2.00.42
Revert "lpfc: Delete unnecessary checks before the function call mempool_destroy"
eata_pio: missing break statement
hpsa: Fix type ZBC conditional checks
scsi_lib: Decode T10 vendor IDs
scsi_dh_alua: do not fail for unknown VPD identification
scsi_debug: use locally assigned naa
scsi_debug: uuid for lu name
scsi_debug: vpd and mode page work
scsi_debug: add multiple queue support
bfa: fix bfa_fcb_itnim_alloc() error handling
megaraid_sas: Downgrade two success messages to info
cxlflash: Fix to resolve dead-lock during EEH recovery
scsi_debug: rework resp_report_luns
scsi_debug: use pdt constants
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft
Pull iscsi_ibft updates from Konrad Rzeszutek Wilk:
"The pull has two features - both of them expand the SysFS entries:
- 'prefix-len' - which is subnet_mask_prefix of the iBFT header.
- 'acpi_header' dir with: 'iBFT', OEM-ID (whatever it extracts from
the iBFT header) and OEM_TABLE_ID (also whatever it extracts from
the iBFT header). This is to help NIC drivers to figure out during
bootup how to deal with BIOS created iBFT tables (like by TianoCore
UEFI implemenation)"
* 'stable/for-linus-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft:
ibft: Expose iBFT acpi header via sysfs
iscsi_ibft: Add prefix-len attr and display netmask
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons.
For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to get
done.
Finally, reset controller handling as always gets merged through here
as well"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
arm-ccn: Enable building as module
soc/tegra: pmc: Add generic PM domain support
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
PCI: tegra: Support per-lane PHYs
dt-bindings: pci: tegra: Update for per-lane PHYs
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
drivers: firmware: psci: make two helper functions inline
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"As usual, a bunch of commits, mostly adding drivers and other options
to defconfigs.
We are adding three new defconfig files for the newly added 32-bit
machines (aspeed and mps2), the rest is mainly housekeeping.
The changes outside of arch/arm/config/ are for a Kconfig symbol that
got renamed"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (63 commits)
ARM: aspeed: adapt defconfigs for new CONFIG_PRINTK_TIME
ARM: u8500_defconfig: update sensor config
ARM: u8500_defconfig: remove staging from defconfig
ARM: multi_v7_defconfig: Remove unused Kconfig option MACH_UX500_DT
ARM: at91/defconfig: sama5: add CONFIG_FHANDLE
arm/configs: Add Aspeed defconfig
arm/configs/multi_v5: Add Aspeed ast2400
ARM: at91: sama5: Update defconfig
ARM: imx_v6_v7_defconfig: add CONFIG_MICREL_PHY
ARM: imx_v6_v7_defconfig: add CONFIG_I2C_GPIO
ARM: multi_v7: Enable Tegra XUSB controller in defconfig
ARM: tegra: Enable XUSB controller in defconfig
ARM: omap2plus_defconfig: Enable PWM and ir-rx51 as loadable modules
ARM: multi_v7_defconfig: add the Atmel sama5d2-compatible ADC driver
ARM: multi_v7_defconfig: add the Atmel Audio microphone interface PDMIC
ARM: multi_v7_defconfig: add Atmel ISI (Image Sensor Interface) driver
ARM: multi_v7_defconfig: add Atmel watchdog timers
ARM: multi_v7_defconfig: add HLCDC drivers as modules
ARM: at91/defconfig: add PDMIC driver to sama5_defconfig
ARM: at91/defconfig: add HLCDC driver to sama5_defconfig
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"We continue ramping up platform support for 64-bit ARM machines, with
111 individual non-merge changesets touching 21 platforms.
The LG1312 platform is completely new and is the first ARM platform by
LG that we support in the mainline kernel. Two other SoCs got added
that are updated versions of existing SoC families, so the port mainly
consists of new dts files:
- The Hisilicon Hip06/D03 is the latest server platform from
Huawei/Hisilicon, and follows the Hip05/D02 platform.
- Rockchip RK3399 follows the 32-bit RK3288 that is popular in
low-end Chromebooks and the 64-bit RK3368 that is mainly found in
chinese Android TV boxes.
The 96Boards HiKey based on the Hisilicon Hi6220 (Kirin 620) gets a
long-awaited overhaul with a lot of devices enabled in the DT, so it
should be much more usable with a mainline kernel now. See also
https://plus.google.com/111524780435806926688/posts/PeGb2VsNhJd
A lot of work went into enabling new device drivers on existing
machines, but we also have a couple of new commercially available
machines:
- Google Pixel C laptop based on Tegra210
- Hardkernel Odroid C2 Based on Amlogic Meson GXBB (S905)
- Geekbuying GeekBox based on Rockchip RK3368
And finally, a couple of reference or development platforms that are
not end-user platforms but are used for trying out the respective SoC
platforms:
- Amlogic Meson GXBB P200 and P201 development systems
- NXP Layerscape 1043A QDS development board
- Hisilicon Hip06 D03 server board, as mentioned above
- LG1312 Reference Design
- RK3399 Evaluation Board"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (104 commits)
arm64: dts: marvell: add XOR node for Armada 3700 SoC
dt-bindings: document rockchip rk3399-evb board
arm64: dts: rockchip: add dts file for RK3399 evaluation board
arm64: dts: rockchip: add core dtsi file for RK3399 SoCs
dt-bindings: rockchip-dw-mshc: add description for rk3399
arm64: dts: marvell: Use a SoC-specific compatible for xHCI on Armada37xx
arm64: dts: marvell: Rename armada-37xx USB node
arm64: dts: marvell: Clean up armada-3720-db
Documentation: arm64: Add Hisilicon Hip06 D03 dts binding
arm64: dts: Add initial dts for Hisilicon Hip06 D03 board
arm64: dts: hip05: Add nor flash support
arm64: dts: hip05: fix its node without msi-cells
arm64: dts: r8a7795: Don't disable referenced optional clocks
arm64: dts: salvator-x: populate EXTALR
arm64: dts: r8a7795: enable PCIe on Salvator-X
arm64: dts: r8a7795: Add PCIe nodes
arm64: tegra: Add IOMMU node to GM20B on Tegra210
arm64: tegra: Add reference clock to GM20B on Tegra210
dt-bindings: Add documentation for GM20B GPU
dt-bindings: gk20a: Document iommus property
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"These are all the updates to device tree files for 32-bit platforms,
which as usual makes up the bulk of the ARM SoC changes: 462 non-merge
changesets, 450 files changed, 23340 insertions, 5216 deletions.
The three platforms that are added with the "soc" branch are here as
well, and we add some related machine files:
- For Aspeed AST2400/AST2500, we get the evaluation platform and the
Tyan Palmetto POWER8 mainboard that uses the AST2400 BMC
- For Oxnas 810SE, the Western Digital "My Book World Edition" is
added as the only platform at the moment.
- For ARM MPS2, the AN385 (Cortex-M3) and AN399 (Cortex-M7) are
supported
On the ARM Realview development platform, we now support all machines
with device tree, previously only the board files were supported,
which in turn will likely be removed soon.
Qualcomm IPQ4019 is the second generation ARM based "Internet
Processor", following the IPQ806x that is used in many high-end WiFi
routers. This one integrates two ath10k wifi radios that were
previously on separate chips.
Other boards that got added for existing chips are:
Ti OMAP family:
- Amazon Kindle Fire, first generation, tablet and ebook reader
- OnRISC Baltos iR 2110 and 3220 embedded industrial PCs
- TI AM5728 IDK, TI AM3359 ICE-V2, and TI DRA722 Rev C EVM
development systems
Samsung EXYNOS platform:
- Samsung ARTIK5 evaluation board, see
https://www.artik.io/modules/overview/artik-5/
NXP i.MX platforms:
- Ka-Ro electronics TX6S-8034, TX6S-8035, TX6U-8033, TX6U-81xx,
TX6Q-1036, TX6Q-1110/-1130, TXUL-0010 and TXUL-0011 industrial
SoM modules
- Embest MarS Board i.MX6Dual DIY platform
- Boundary Devices i.MX6 Quad Plus Nitrogen6_MAX and SoloX
Nitrogen6sx embedded boards
- Technexion Pico i.MX6UL compute module
- ZII VF610 Development Board
Marvell embedded (mvebu, orion, kirkwood) platforms:
- Linksys Viper (E4200v2 / EA4500) WiFi router
- Buffalo Kurobox Pro NAS
Qualcomm Snapdragon:
- Arrow DragonBoard 600c (96boards) with APQ8064 Snapdragon 600
Rockchips platform:
- mqmaker MiQi single-board computer
Altera SoCFPGA:
- samtec VIN|ING 1000 vehicle communication interface
Allwinner Sunxi platforms:
- Dserve DSRV9703C tablet
- Difrnce DIT4350 tablet
- Colorfly E708 Q1 tablet
- Polaroid MID2809PXE04 tablet
- Olimex A20 OLinuXino LIME2 single board computer
- Xunlong Orange Pi 2, Orange Pi One, and Orange Pi PC single board
computers
Across many platforms, bug fixes went in to address warnings that dtc
now emits with 'make dtbs W=1'. Further changes for device enablement
went into Ti OMAP, bcm283x (Raspberry Pi), bcm47xx (wifi router), Ti
Davinci, Samsung EXYNOS, Marvell mvebu/kirkwood/orion, NXP i.MX/Vybrid
NXP LPC18xx, NXP LPC32xx, Renesas shmobile/r-mobile/r-car, Rockchips
rk3xxx, ST Ux500, ST STi, Atmel AT91/SAMA5, Altera SoCFPGA, Allwinner
Sunxi, Sigma Designs Tango, NVIDIA Tegra, Socionext Uniphier and ARM
Versatile Express"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (458 commits)
ARM: dts: tango4: Import watchdog node
ARM: dts: tango4: Update cpus node for cpufreq
ARM: dts: tango4: Update DT to match clk driver
ARM: dts: tango4: Initial thermal support
arm/dst: Add Aspeed ast2500 device tree
arm/dts: Add Aspeed ast2400 device tree
ARM: sun7i: dt: Add pll3 and pll7 clocks
ARM: dts: sunxi: Add a olinuxino-lime2-emmc
ARM: dts: at91: sama5d4: add trng node
ARM: dts: at91: sama5d3: add trng node
ARM: dts: at91: sama5d2: add trng node
ARM: dts: at91: at91sam9g45 family: reduce the trng register map size
ARM: sun4i: dt: Add pll3 and pll7 clocks
ARM: sun5i: chip: Enable the TV Encoder
ARM: sun5i: r8: Add display blocks to the DTSI
ARM: sun5i: a13: Add display and TCON clocks
ARM: dts: ux500: configure the accelerometers open drain
ARM: mx5: dts: Enable USB OTG on M53EVK
ARM: dts: imx6ul-14x14-evk: Add audio support
ARM: dts: imx6qdl: Remove unneeded unit-addresses
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit changes from Arnd Bergmann:
"One new platform gets added this time: The Cortex-A53 based LG
Electronics LG1K platform used in digital TVs.
The other changes are mostly smaller updates to the defconfig files,
to enable additional platform specific drivers, as they get merged
through the subsystem trees"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: configs: add options useful for Armada 7K/8K support
arm64: defconfig: Add Juno SATA controller
arm64: defconfig: enable freescale/nxp config options
arm64: defconfig: enable 48-bit virtual addresses
arm64: defconfig: cleanup the defconfig
MAINTAINERS: update entry for Marvell ARM platform maintainers
arm64: marvell: enable AP806 and CP110 syscon driver
arm64: Kconfig: select sp804 timer for ARCH_HISI
arm64: defconfig: enable configs for WLAN and TI WL1835 as modules
arm64: defconfig: enable several common USB network adapters
arm64: defconfig: add CONFIG_SPI_SPIDEV as module
arm64: defconfig: Enable the PMIC and regulator for Hi6220 and 96boards HiKey
arm64: defconfig: Add Renesas R-Car USB 3.0 driver support
MAINTAINERS: add Chanho Min as ARM/LG1K maintainer
arm64: defconfig: enable ARCH_LG1K
arm64: add Kconfig entry for LG1K SoC family
arm64: defconfig: Enable PL330 DMA controller
arm64: defconfig: enable basic boot for Amlogic meson
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"We get support for three new 32-bit SoC platforms this time.
The amount of changes in arch/arm for any of them is miniscule, as all
the interesting code is in device driver subsystems (irqchip, clk,
pinctrl, ...) these days. I'm listing them here, as the addition of
the Kconfig statement is the main relevant milestone for a new
platform. In each case, some drivers are are shared with existing
platforms, while other drivers are added for v4.7 as well, or come in
a later release.
- The Aspeed platform is probably the most interesting one, this is
what most whitebox servers use as their baseboard management
controller. We get support for the very common ast2400 and ast2500
SoCs. The OpenBMC project focuses on this chip, and the LWN
article about their ELC 2016 presentation at
https://lwn.net/Articles/683320/
triggered the submission, but the code comes from IBM's OpenPOWER
team rather than the team at Facebook. There are still a lot more
drivers that need to get added over time, and I hope both teams can
work together on that.
- OXNAS is an old platform for Network Attached Storage devices from
Oxford Semiconductor. There are models with ARM10 (!) and
ARM11MPCore cores, but for now, we only support the original ARM9
based versions. The product lineup was subsequently part of PLX,
Avago and now the new Broadcom Ltd.
https://wiki.openwrt.org/doc/hardware/soc/soc.oxnas
has some more information.
- V2M-MPS2 is a prototyping platform from ARM for their Cortex-M
cores and is related to the existing Realview / Versatile Express
lineup, but without MMU.
We now support various NOMMU platforms, so adding a new one is
fairly straightforward.
http://infocenter.arm.com/help/topic/com.arm.doc.100112_0100_03_en/
has detailed information about the platform.
Other noteworthy updates:
- Work on LPC32xx has resumed, and Vladimir Zapolskiy and Sylvain
Lemieux are now maintaining the platform.
This is an older ARM9 based platform from NXP (not Freescale), but
it remains in use in embedded markets.
- Kevin Hilman is now co-maintaining the Amlogic Meson platform for
both 32-bit and 64-bit ARM, and started contributing some patches.
- As is often the case, work on the OMAP platforms makes up the bulk
of the actual SoC code changes in arch/arm, but there isn't a lot
of that either"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
MAINTAINERS: ARM/Amlogic: add co-maintainer, misc. updates
MAINTAINERS: add ARM/NXP LPC32XX SoC specific drivers to the section
MAINTAINERS: add new maintainers of NXP LPC32xx SoC
MAINTAINERS: move ARM/NXP LPC32xx record to ARM section
arm: Add Aspeed machine
ARM: lpc32xx: remove duplicate const on lpc32xx_auxdata_lookup
ARM: lpc32xx: remove leftovers of legacy clock source and provider drivers
ARM: lpc32xx: remove reboot header file
ARM: dove: Remove CLK_IS_ROOT
ARM: orion5x: Remove CLK_IS_ROOT
ARM: mv78xx0: Remove CLK_IS_ROOT
ARM: davinci: da850: use clk->set_parent for async3
ARM: davinci: Move clock init after ioremap.
MAINTAINERS: Update ARM Versatile Express platform entry
ARM: vexpress/mps2: introduce MPS2 platform
MAINTAINERS: add maintainer entry for ARM/OXNAS platform
ARM: Add new mach-oxnas
irqchip: versatile-fpga: add new compatible for OX810SE SoC
ARM: uniphier: correct the call order of of_node_put()
MAINTAINERS: fix stale TI DaVinci entries
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups and fixes from Arnd Bergmann:
"Traditionally we've had two separate branches for cleanups and
non-critical bug fixes, but both of these got smaller with each
release and the differences are rather unclear now, so it seems more
appropriate to have a combined branch.
The most notable change is for OMAP, which gets a small rework to
simplify handling of the AUXDATA mechanism used on machines that are
not completely DT based yet, along with other work that is used as
preparation for dropping the legacy board files"
* tag 'armsoc-cleanups-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: exynos: Add interrupt line to MAX8997 PMIC on exynos4210-trats
ARM: dts: exynos: Fix regulator name to avoid forbidden character on exynos4210-trats
ARM: dts: exynos: Add MFC memory banks for Peach boards
ARM: OMAP2+: n900 needs MMC slot names for legacy user space
ARM: OMAP2+: Add more functions to pwm pdata for ir-rx51
ARM: debug: remove extraneous DEBUG_HI3716_UART option
ARM: OMAP2+: Simplify auxdata by using the generic match
of/platform: Allow secondary compatible match in of_dev_lookup
ARM: davinci: use IRQCHIP_DECLARE for cp_intc
ARM: davinci: remove unused DA8XX_NUM_UARTS
ARM: davinci: simplify call to of populate
ARM: DaVinci USB: removed deprecated properties from MUSB config
ARM: rockchip: Fix use of plain integer as NULL pointer
ARM: realview: hide unused 'pmu_device' object
soc: versatile: dynamically detect RealView HBI numbers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
"The s390 patches for the 4.7 merge window have the usual bug fixes and
cleanups, and the following new features:
- An interface for dasd driver to query if a volume is online to
another operating system
- A new ioctl for the dasd driver to verify the format for a range of
tracks
- Following the example of x86 the struct fpu is now allocated with
the task_struct
- The 'report_error' interface for the PCI bus to send an
adapter-error notification from user space to the service element
of the machine"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (29 commits)
s390/vmem: remove unused function parameter
s390/vmem: fix identity mapping
s390: add missing include statements
s390: add missing declarations
s390: make couple of variables and functions static
s390/cache: remove superfluous locking
s390/cpuinfo: simplify locking and skip offline cpus early
s390/3270: hangup the 3270 tty after a disconnect
s390/3270: handle reconnect of a tty with a different size
s390/3270: avoid endless I/O loop with disconnected 3270 terminals
s390/3270: fix garbled output on 3270 tty view
s390/3270: fix view reference counting
s390/3270: add missing tty_kref_put
s390/dumpstack: implement and use return_address()
s390/cpum_sf: Remove superfluous SMP function call
s390/cpum_cf: Remove superfluous SMP function call
s390/Kconfig: make z196 the default processor type
s390/sclp: avoid compile warning in sclp_pci_report
s390/fpu: allocate 'struct fpu' with the task_struct
s390/crypto: cleanup and move the header with the cpacf definitions
...
|
|
My laptop that uses the intel 7680 iwlwifi module would no longer
connects to the network. It would fail with a "Microcode SW error
detected." and spew out register state over and over again without ever
connecting to the network.
The cause is mis-merge in commit 909b27f70643, where David seems to have
lost some of the changes to iwl_mvm_set_tx_cmd() from commit
5c08b0f5026f ("iwlwifi: mvm: don't override the rate with the AMSDU
len").
The reason seems to be a conflict with commit d8fe484470dd ("iwlwifi:
mvm: add support for new TX CMD API"), which touched a line adjacent to
the changes in 909b27f70643.
David missed the fact that "info->driver_data[0]" had become
"skb_info->driver_data[0]". Then he removed the skb_info because it was
unused.
This just re-updates iwl_mvm_set_tx_cmd() with the lost two lines.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Reinoud Koornstra <reinoudkoornstra@gmail.com>
Cc: Luciano Coelho <luciano.coelho@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs cleanups from Al Viro:
"Assorted cleanups and fixes all over the place"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
coredump: only charge written data against RLIMIT_CORE
coredump: get rid of coredump_params->written
ecryptfs_lookup(): try either only encrypted or plaintext name
ecryptfs: avoid multiple aliases for directories
bpf: reject invalid names right in ->lookup()
__d_alloc(): treat NULL name as QSTR("/", 1)
mtd: switch ubi_open_volume_path() to vfs_stat()
mtd: switch open_mtd_by_chdev() to use of vfs_stat()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull iov_iter cleanups from Al Viro.
* 'work.iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fold checks into iterate_and_advance()
rw_verify_area(): saner calling conventions
aio: remove a pointless assignment
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull parallel lookup fixups from Al Viro:
"Fix for xfs parallel readdir (turns out the cxfs exposure was not
enough to catch all problems), and a reversion of btrfs back to
->iterate() until the fs/btrfs/delayed-inode.c gets fixed"
* 'work.lookups' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
xfs: concurrent readdir hangs on data buffer locks
Revert "btrfs: switch to ->iterate_shared()"
|
|
There's a three-process deadlock involving shared/exclusive barriers
and inverted lock orders in the directory readdir implementation.
It's a pre-existing problem with lock ordering, exposed by the
VFS parallelisation code.
process 1 process 2 process 3
--------- --------- ---------
readdir
iolock(shared)
get_leaf_dents
iterate entries
ilock(shared)
map, lock and read buffer
iunlock(shared)
process entries in buffer
.....
readdir
iolock(shared)
get_leaf_dents
iterate entries
ilock(shared)
map, lock buffer
<blocks>
finish ->iterate_shared
file_accessed()
->update_time
start transaction
ilock(excl)
<blocks>
.....
finishes processing buffer
get next buffer
ilock(shared)
<blocks>
And that's the deadlock.
Fix this by dropping the current buffer lock in process 1 before
trying to map the next buffer. This means we keep the lock order of
ilock -> buffer lock intact and hence will allow process 3 to make
progress and drop it's ilock(shared) once it is done.
Reported-by: Xiong Zhou <xzhou@redhat.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
This reverts commit 972b241f8441dc37a3f89dcd7e71d7f013873d13.
Quoth Chris:
didn't take the delayed inode stuff into account
it got an rbtree of items and it pulls things out
so in shared mode, its hugely racey
sorry, lets revert and fix it for real inside of btrfs
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull cifs iovec cleanups from Al Viro.
* 'sendmsg.cifs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
cifs: don't bother with kmap on read_pages side
cifs_readv_receive: use cifs_read_from_socket()
cifs: no need to wank with copying and advancing iovec on recvmsg side either
cifs: quit playing games with draining iovecs
cifs: merge the hash calculation helpers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull remaining vfs xattr work from Al Viro:
"The rest of work.xattr (non-cifs conversions)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
btrfs: Switch to generic xattr handlers
ubifs: Switch to generic xattr handlers
jfs: Switch to generic xattr handlers
jfs: Clean up xattr name mapping
gfs2: Switch to generic xattr handlers
ceph: kill __ceph_removexattr()
ceph: Switch to generic xattr handlers
ceph: Get rid of d_find_alias in ceph_set_acl
|
|
Pull cifs updates from Steve French:
"Various small CIFS and SMB3 fixes (including some for stable)"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
remove directory incorrectly tries to set delete on close on non-empty directories
Update cifs.ko version to 2.09
fs/cifs: correctly to anonymous authentication for the NTLM(v2) authentication
fs/cifs: correctly to anonymous authentication for the NTLM(v1) authentication
fs/cifs: correctly to anonymous authentication for the LANMAN authentication
fs/cifs: correctly to anonymous authentication via NTLMSSP
cifs: remove any preceding delimiter from prefix_path
cifs: Use file_dentry()
|
|
MSR 0x2f8 accessed the 124th Variable Range MTRR ever since MTRR support
was introduced by 9ba075a664df ("KVM: MTRR support").
0x2f8 became harmful when 910a6aae4e2e ("KVM: MTRR: exactly define the
size of variable MTRRs") shrinked the array of VR MTRRs from 256 to 8,
which made access to index 124 out of bounds. The surrounding code only
WARNs in this situation, thus the guest gained a limited read/write
access to struct kvm_arch_vcpu.
0x2f8 is not a valid VR MTRR MSR, because KVM has/advertises only 16 VR
MTRR MSRs, 0x200-0x20f. Every VR MTRR is set up using two MSRs, 0x2f8
was treated as a PHYSBASE and 0x2f9 would be its PHYSMASK, but 0x2f9 was
not implemented in KVM, therefore 0x2f8 could never do anything useful
and getting rid of it is safe.
This fixes CVE-2016-3713.
Fixes: 910a6aae4e2e ("KVM: MTRR: exactly define the size of variable MTRRs")
Cc: stable@vger.kernel.org
Reported-by: David Matlack <dmatlack@google.com>
Signed-off-by: Andy Honig <ahonig@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Neither APICv nor AVIC actually need the first argument of
hwapic_isr_update, but the vCPU makes more sense than passing the
pointer to the whole virtual machine! In fact in the APICv case it's
just happening that the vCPU is used implicitly, through the loaded VMCS.
The second argument instead is named differently, make it consistent.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When a vcpu is loaded/unloaded to a physical core, we need to update
host physical APIC ID information in the Physical APIC-ID table
accordingly.
Also, when vCPU is blocking/un-blocking (due to halt instruction),
we need to make sure that the is-running bit in set accordingly in the
physical APIC-ID table.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
[Return void from new functions, add WARN_ON when they returned negative
errno; split load and put into separate function as they have almost
nothing in common. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When enable AVIC:
* Do not intercept CR8 since this should be handled by AVIC HW.
* Also, we don't need to sync cr8/V_TPR and APIC backing page.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
[Rename svm_in_nested_interrupt_shadow to svm_nested_virtualize_tpr. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Since AVIC only virtualizes xAPIC hardware for the guest, this patch
disable x2APIC support in guest CPUID.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Adding kvm_x86_ops hooks to allow APICv to do post state restore.
This is required to support VM save and restore feature.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This patch introduces VMEXIT handlers, avic_incomplete_ipi_interception()
and avic_unaccelerated_access_interception() along with two trace points
(trace_kvm_avic_incomplete_ipi and trace_kvm_avic_unaccelerated_access).
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This patch introduces a new mechanism to inject interrupt using AVIC.
Since VINTR is not supported when enable AVIC, we need to inject
interrupt via APIC backing page instead.
This patch also adds support for AVIC doorbell, which is used by
KVM to signal a running vcpu to check IRR for injected interrupts.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This patch introduces AVIC-related data structure, and AVIC
initialization code.
There are three main data structures for AVIC:
* Virtual APIC (vAPIC) backing page (per-VCPU)
* Physical APIC ID table (per-VM)
* Logical APIC ID table (per-VM)
Currently, AVIC is disabled by default. Users can manually
enable AVIC via kernel boot option kvm-amd.avic=1 or during
kvm-amd module loading with parameter avic=1.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
[Avoid extra indentation (Boris). - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Introduce new AVIC VMCB registers.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
AVIC has a use for kvm_vcpu_wake_up.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Tested-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Adding new function pointer in struct kvm_x86_ops, and calling them
from the kvm_arch_vcpu[blocking/unblocking].
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Adding function pointers in struct kvm_x86_ops for processor-specific
layer to provide hooks for when KVM initialize and destroy VM.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Rename kvm_apic_get_reg to kvm_lapic_get_reg to be consistent with
the existing kvm_lapic_set_reg counterpart.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Exporting LAPIC utility functions and macros for re-use in SVM code.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
commit 3491caf2755e ("KVM: halt_polling: provide a way to qualify
wakeups during poll") added more aggressive shrinking of the
polling interval if the wakeup did not match some criteria. This
still allows to keep polling enabled if the polling time was
smaller that the current max poll time (block_ns <= vcpu->halt_poll_ns).
Performance measurement shows that even more aggressive shrinking
(shrink polling on any invalid wakeup) reduces absolute and relative
(to the workload) CPU usage even further.
Cc: David Matlack <dmatlack@google.com>
Cc: Wanpeng Li <kernellwp@gmail.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The most recent release of AXS103 [v1.1] is proven to work
at 100 MHz in dual-core mode so this change uses mentioned feature.
For that we:
* Update axc003_idu.dtsi with mention of really-used CPU clock freq
* Remove clock override in AXS platform code for dual-core HW
Note we're still leaving a hack for clock "downgrade" on early boot
for quad-core hardware.
Also note this change will break functionality of AXS103 v1.0 hardware.
That means all users of AXS103 __must__ upgrade their boards with the
most recent firmware.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
|
