summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2014-05-05net: macb: Fix race between HW and driverSoren Brinkmann1-10/+0
Under "heavy" RX load, the driver cannot handle the descriptors fast enough. In detail, when a descriptor is consumed, its used flag is cleared and once the RX budget is consumed all descriptors with a cleared used flag are prepared to receive more data. Under load though, the HW may constantly receive more data and use those descriptors with a cleared used flag before they are actually prepared for next usage. The head and tail pointers into the RX-ring should always be valid and we can omit clearing and checking of the used flag. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05net: macb: Remove 'unlikely' optimizationSoren Brinkmann1-1/+1
Coverage data suggests that the unlikely case of receiving data while the receive handler is running may not be that unlikely. Coverage data after running iperf for a while: 91320: 891: work_done = bp->macbgem_ops.mog_rx(bp, budget); 91320: 892: if (work_done < budget) { 2362: 893: napi_complete(napi); -: 894: -: 895: /* Packets received while interrupts were disabled */ 4724: 896: status = macb_readl(bp, RSR); 2362: 897: if (unlikely(status)) { 762: 898: if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE) 762: 899: macb_writel(bp, ISR, MACB_BIT(RCOMP)); -: 900: napi_reschedule(napi); -: 901: } else { 1600: 902: macb_writel(bp, IER, MACB_RX_INT_FLAGS); -: 903: } -: 904: } Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05net: macb: Re-enable RX interrupt only when RX is doneSoren Brinkmann1-7/+6
When data is received during the driver processing received data the NAPI is re-scheduled. In that case the RX interrupt should not be re-enabled. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05net: macb: Clear interrupt flagsSoren Brinkmann1-0/+10
A few interrupt flags were not cleared in the ISR, resulting in a sytem trapped in the ISR in cases one of those interrupts occurred. Clear all flags to avoid such situations. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05net: macb: Pass same size to DMA_UNMAP as used for DMA_MAPSoren Brinkmann1-1/+1
Just as commit "net: macb: DMA-unmap full rx-buffer" (48330e08fa168395b9fd9f369f06cca1df204361), pass the size that was used for mapping the memory also to the unmap routine to avoid warnings from the DMA_API. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05ip_tunnel: Set network header properly for IP_ECN_decapsulate()Ying Cai1-0/+2
In ip_tunnel_rcv(), set skb->network_header to inner IP header before IP_ECN_decapsulate(). Without the fix, IP_ECN_decapsulate() takes outer IP header as inner IP header, possibly causing error messages or packet drops. Note that this skb_reset_network_header() call was in this spot when the original feature for checking consistency of ECN bits through tunnels was added in eccc1bb8d4b4 ("tunnel: drop packet if ECN present with not-ECT"). It was only removed from this spot in 3d7b46cd20e3 ("ip_tunnel: push generic protocol handling to ip_tunnel module."). Fixes: 3d7b46cd20e3 ("ip_tunnel: push generic protocol handling to ip_tunnel module.") Reported-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Ying Cai <ycai@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05Merge branch 'master' of ↵David S. Miller3-29/+46
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates This series contains updates to e1000e only. David provides four fixes for e1000e, first is a workaround for a hardware erratum on 82579 devices which experienced packet loss in gigabit and 100 speeds when interconnect between the PHY and MAC is exiting K1 power saving state. Second expands the scope of a workaround to include i217 and i218 parts as well to address over aggressive transmit behavior when connecting at 10Mbs half-duplex. Next is to resolve a reported link flap issue on 82579 parts which was root caused as an interoperability problem between 82579 and at least some Broadcom PHYs in the Energy Efficient Ethernet wake mechanism. Lastly, restricts the workaround of putting the PHY into MDIO slow mode to access the PHY id to relevant parts since this issue has been fixed on the newer hardware. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05e1000e: Restrict MDIO Slow Mode workaround to relevant partsDavid Ertman1-6/+8
It has been determined that the workaround of putting the PHY into MDIO slow mode to access the PHY id is not necessary with Lynx Point and newer parts. The issue that necessitated the workaround has been fixed on the newer hardware. We will maintains, as a last ditch attempt, the conversion to MDIO Slow Mode in the failure branch when attempting to access the PHY id so as to cover all contingencies. Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-05e1000e: Fix issue with link flap on 82579David Ertman2-0/+13
Several customers have reported a link flap issue on 82579. The symptoms are random and intermittent link losses when 82579 is connected to specific link partners. Issue has been root caused as interoperability problem between 82579 and at least some Broadcom PHYs in the Energy Efficient Ethernet wake mechanism. To fix the issue, we are disabling the Phase Locked Loop shutdown in 100M Low Power Idle. This solution will cause an increase of power in 100M EEE link. It will cost additional 28mW in this specific mode. Cc: Lukasz Adamczuk <lukasz.adamczuk@intel.com> Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-05e1000e: Expand workaround for 10Mb HD throughput bugDavid Ertman2-4/+12
In commit 772d05c51c4f4896c120ad418b1e91144a2ac813 "e1000e: slow performance between two 82579 connected via 10Mbit hub", a workaround was put into place to address the overaggressive transmit behavior of 82579 parts when connecting at 10Mbs half-duplex. This same behavior is seen on i217 and i218 parts as well. This patch expands the original workaround to encompass these parts. Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-05e1000e: Workaround for dropped packets in Gig/100 speeds on 82579David Ertman2-19/+13
This is a workaround for a HW erratum on 82579 devices. Erratum is #23 in Intel 6 Series Chipset and Intel C200 Series Chipset specification Update June 2013. Problem: 82579 parts experience packet loss in Gig and 100 speeds when interconnect between PHY and MAC is exiting K1 power saving state. This was previously believed to only affect 1Gig speed, but has been observed at 100Mbs also. Workaround: Disable K1 for 82579 devices at Gig and 100 speeds. Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-05Merge branch 'mlx4'David S. Miller3-18/+47
Or Gerlitz says: ==================== This series contains fixes for 3.15-rc, mostly around SRIOV. The patches by Jack, Matan and myself fix few issues related to mlx4 SRIOV support for RoCE and single port VFs, and the patch from Eyal eliminates checking PCI caps for VFs which is misleading. Patches done against the net tree, commit 014f1b2 "net: bonding: Fix format string mismatch in bond_sysfs.c" We'd be happy to get Eyal's patch queued in your -stable list for 3.14.y ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05net/mlx4_core: Don't issue PCIe speed/width checks for VFsEyal Perry1-1/+2
Carrying out PCI speed/width checks through pcie_get_minimum_link() on VFs yield wrong results, so remove them. Fixes: b912b2f ('net/mlx4_core: Warn if device doesn't have enough PCI bandwidth') Signed-off-by: Eyal Perry <eyalpe@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05net/mlx4_core: Load the Eth driver firstOr Gerlitz1-2/+2
When running in SRIOV mode, VM that is assigned with a non-provisioned Ethernet VFs get themselves a random mac when the Eth driver starts. In this case, if the IB driver startup code that deals with RoCE runs first, it will use a zero mac as the source mac for the Para-Virtual CM MADs which is buggy. To handle that, we change the order of loading. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05net/mlx4_core: Fix slave id computation for single port VFMatan Barak1-15/+20
The code that deals with computing the slave id based on a given GID gave wrong results when the number of single port VFs wasn't the same for port 1 vs. port 2 and the relevant VF is single ported on port 2. As a result, incoming CM MADs were dispatched to the wrong VF. Fixed that and added documentation to clarify the computation steps. Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF') Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05net/mlx4_core: Adjust port number in qp_attach wrapper when detachingJack Morgenstein1-0/+23
When using single ported VFs and the VF is using port 2, we need to adjust the port accordingly (change it from 1 to 2). Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF') Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05net: cdc_ncm: fix buffer overflowBjørn Mork1-1/+1
Commit 4d619f625a60 ("net: cdc_ncm: no point in filling up the NTBs if we send ZLPs") changed the padding logic for devices with the ZLP flag set. This meant that frames of any size will be sent without additional padding, except for the single byte added if the size is a multiple of the USB packet size. But if the unpadded size is identical to the maximum frame size, and the maximum size is a multiplum of the USB packet size, then this one-byte padding will overflow the buffer. Prevent padding if already at maximum frame size, letting usbnet transmit a ZLP instead in this case. Fixes: 4d619f625a60 ("net: cdc_ncm: no point in filling up the NTBs if we send ZLPs") Reported by: Yu-an Shih <yshih@nvidia.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05Altera TSE: ALTERA_TSE should depend on HAS_DMAGeert Uytterhoeven1-0/+1
If NO_DMA=y: drivers/built-in.o: In function `altera_tse_probe': altera_tse_main.c:(.text+0x25ec2e): undefined reference to `dma_set_mask' altera_tse_main.c:(.text+0x25ec78): undefined reference to `dma_supported' altera_tse_main.c:(.text+0x25ecb6): undefined reference to `dma_supported' drivers/built-in.o: In function `sgdma_async_read': altera_sgdma.c:(.text+0x25f620): undefined reference to `dma_sync_single_for_cpu' drivers/built-in.o: In function `sgdma_uninitialize': (.text+0x25f678): undefined reference to `dma_unmap_single' drivers/built-in.o: In function `sgdma_uninitialize': (.text+0x25f696): undefined reference to `dma_unmap_single' drivers/built-in.o: In function `sgdma_initialize': (.text+0x25f6f0): undefined reference to `dma_map_single' drivers/built-in.o: In function `sgdma_initialize': (.text+0x25f702): undefined reference to `dma_mapping_error' drivers/built-in.o: In function `sgdma_tx_buffer': (.text+0x25f92a): undefined reference to `dma_sync_single_for_cpu' drivers/built-in.o: In function `sgdma_rx_status': (.text+0x25fa24): undefined reference to `dma_sync_single_for_cpu' make[3]: *** [vmlinux] Error 1 Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Vince Bridgers <vbridgers2013@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05vsock: Make transport the proto ownerAndy King2-26/+27
Right now the core vsock module is the owner of the proto family. This means there's nothing preventing the transport module from unloading if there are open sockets, which results in a panic. Fix that by allowing the transport to be the owner, which will refcount it properly. Includes version bump to 1.0.1.0-k Passes checkpatch this time, I swear... Acked-by: Dmitry Torokhov <dtor@vmware.com> Signed-off-by: Andy King <acking@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05Merge branch 'for-davem' of ↵David S. Miller18-50/+57
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless John W. Linville says: ==================== pull request: wireless 2014-05-01 Please pull the following batch of fixes intended for the 3.15 stream! For the Bluetooth bits, Gustavo says: "Some fixes for 3.15. There is a revert for the intel driver, a new device id, and two important SSP fixes from Johan." On top of that... Ben Hutchings gives us a fix for an unbalanced irq enable in an rtl8192cu error path. Colin Ian King provides an rtlwifi fix for an uninitialized variable. Felix Fietkau brings a pair of ath9k fixes, one that corrects a hardware initialization value and another that removes an (unnecessary) flag that was being used in a way that led to a software tx queue hang in ath9k. Gertjan van Wingerde pushes a MAINTAINERS change to remove himself from the rt2x00 maintainer team. Hans de Goede fixes a brcmfmac firmware load hang. Larry Finger changes rtlwifi to use the correct queue for V0 traffic on rtl8192se. Rajkumar Manoharan corrects a race in ath9k driver initialization. Stanislaw Gruszka fixes an rt2x00 bug in which disabling beaconing once on USB devices led to permanently disabling beaconing for those devices. Tim Harvey provides fixes for a pair of ath9k issues that can lead to soft lockups in that driver. Please let me know if there are problems! ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-04net: sched: lock imbalance in hhf qdiscJohn Fastabend1-5/+6
hhf_change() takes the sch_tree_lock and releases it but misses the error cases. Fix the missed case here. To reproduce try a command like this, # tc qdisc change dev p3p2 root hhf quantum 40960 non_hh_weight 300000 Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-02net: mvmdio: Check for a valid interrupt instead of an errorEzequiel Garcia1-1/+4
The following commit: commit 9ec36cafe43bf835f8f29273597a5b0cbc8267ef Author: Rob Herring <robh@kernel.org> Date: Wed Apr 23 17:57:41 2014 -0500 of/irq: do irq resolution in platform_get_irq changed platform_get_irq() which now returns EINVAL and EPROBE_DEFER, in addition to ENXIO. If there's no interrupt for mvmdio, platform_get_irq() returns EINVAL, but we currently check only for ENXIO. Fix this by looking for a positive integer, which is the proper way of validating a virtual interrupt number. While at it, add a proper handling for the deferral probe case. Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-02net phy: Check for aneg completion before setting state to PHY_RUNNINGBalakumaran Kannan1-0/+11
phy_state_machine should check whether auto-negotiatin is completed before changing phydev->state from PHY_NOLINK to PHY_RUNNING. If auto-negotiation is not completed phydev->state should be set to PHY_AN. Signed-off-by: Balakumaran Kannan <kumaran.4353@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-01Merge branch 'master' of ↵John W. Linville18-50/+57
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
2014-04-30hyperv: Properly handle checksum offloadKY Srinivasan1-0/+4
Do checksum offload only if the client of the driver wants checksum to be offloaded. In V1 version of this patch, I addressed comments from Stephen Hemminger <stephen@networkplumber.org> and Eric Dumazet <eric.dumazet@gmail.com>. In this version of the patch I have addressed comments from David Miller. This patch fixes a bug that is exposed in gateway scenarios. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-30gianfar: Avoid unnecessary reg accesses in adjust_link()Claudiu Manoil1-110/+113
For phy devices that don't issue interrupts upon link state changes, phylib polls the link state resulting in repeated calls to adjust_link(), even if the link state didn't change. As a result, some mac registers are repeatedly read and written with the same values, which is not ok. To fix this, adjust_link() has been refactored to check first whether the link state has changed and to take action only if needed, updating mac registers and local state variables. The 'new_state' local flag, set if one of the link params changed (link, speed or duplex), has been rendered useless and removed by this refactoring. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-30tcp_cubic: fix the range of delayed_ackLiu Yu1-1/+1
commit b9f47a3aaeab (tcp_cubic: limit delayed_ack ratio to prevent divide error) try to prevent divide error, but there is still a little chance that delayed_ack can reach zero. In case the param cnt get negative value, then ratio+cnt would overflow and may happen to be zero. As a result, min(ratio, ACK_RATIO_LIMIT) will calculate to be zero. In some old kernels, such as 2.6.32, there is a bug that would pass negative param, which then ultimately leads to this divide error. commit 5b35e1e6e9c (tcp: fix tcp_trim_head() to adjust segment count with skb MSS) fixed the negative param issue. However, it's safe that we fix the range of delayed_ack as well, to make sure we do not hit a divide by zero. CC: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Liu Yu <allanyuliu@tencent.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-30bpf_dbg: fix wrong register usageBrendan Hickey1-1/+1
The AND instruction is erroneously using the X register instead of the K register. Signed-off-by: Brendan Hickey <bhickey@google.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-30Revert "macvlan : fix checksums error when we are in bridge mode"Vlad Yasevich1-3/+0
This reverts commit 12a2856b604476c27d85a5f9a57ae1661fc46019. The commit above doesn't appear to be necessary any more as the checksums appear to be correctly computed/validated. Additionally the above commit breaks kvm configurations where one VM is using a device that support checksum offload (virtio) and the other VM does not. In this case, packets leaving virtio device will have CHECKSUM_PARTIAL set. The packets is forwarded to a macvtap that has offload features turned off. Since we use CHECKSUM_UNNECESSARY, the host does does not update the checksum and thus a bad checksum is passed up to the guest. CC: Daniel Lezcano <daniel.lezcano@free.fr> CC: Patrick McHardy <kaber@trash.net> CC: Andrian Nord <nightnord@gmail.com> CC: Eric Dumazet <eric.dumazet@gmail.com> CC: Michael S. Tsirkin <mst@redhat.com> CC: Jason Wang <jasowang@redhat.com> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-30mactap: Fix checksum errors for non-gso packets in bridge modeVlad Yasevich1-0/+9
The following is a problematic configuration: VM1: virtio-net device connected to macvtap0@eth0 VM2: e1000 device connect to macvtap1@eth0 The problem is is that virtio-net supports checksum offloading and thus sends the packets to the host with CHECKSUM_PARTIAL set. On the other hand, e1000 does not support any acceleration. For small TCP packets (and this includes the 3-way handshake), e1000 ends up receiving packets that only have a partial checksum set. This causes TCP to fail checksum validation and to drop packets. As a result tcp connections can not be established. Commit 3e4f8b787370978733ca6cae452720a4f0c296b8 macvtap: Perform GSO on forwarding path. fixes this issue for large packets wthat will end up undergoing GSO. This commit adds a check for the non-GSO case and attempts to compute the checksum for partially checksummed packets in the non-GSO case. CC: Daniel Lezcano <daniel.lezcano@free.fr> CC: Patrick McHardy <kaber@trash.net> CC: Andrian Nord <nightnord@gmail.com> CC: Eric Dumazet <eric.dumazet@gmail.com> CC: Michael S. Tsirkin <mst@redhat.com> CC: Jason Wang <jasowang@redhat.com> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-30tcp: increment retransmit counters in tlp and fast openEric Dumazet1-7/+7
Both TLP and Fast Open call __tcp_retransmit_skb() instead of tcp_retransmit_skb() to avoid changing tp->retrans_out. This has the side effect of missing SNMP counters increments as well as tcp_info tcpi_total_retrans updates. Fix this by moving the stats increments of into __tcp_retransmit_skb() Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Nandita Dukkipati <nanditad@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-30net: sxgbe: Added set function for interrupt on completeByungho An3-0/+11
This patch adds set_rx_int_on_com function for interrupt when dma is completed. Signed-off-by: Byungho An <bh74.an@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-30net: sxgbe: Added rxqueue enable functionByungho An4-0/+36
This patch adds rxqueue enable function according to number of rxqueue and adds rxqueue disable function for removing. Signed-off-by: Byungho An <bh74.an@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-30net: sxgbe: sw reset moved to probe functionByungho An2-13/+22
This patch moves sw reset to probe function because sw reset is needed early stage before open function. Signed-off-by: Byungho An <bh74.an@samsung.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-30cxgb4: Decode PCIe Gen3 link speedRoland Dreier1-0/+2
Add handling for " 8 GT/s" in print_port_info(). Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-30Altera TSE: Add missing include to silence sparse warningsTobias Klauser1-0/+1
This fixes the following sparse warnings: drivers/net/ethernet/altera/altera_msgdma.c:23:5: warning: symbol 'msgdma_initialize' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:28:6: warning: symbol 'msgdma_uninitialize' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:32:6: warning: symbol 'msgdma_reset' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:77:6: warning: symbol 'msgdma_disable_rxirq' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:83:6: warning: symbol 'msgdma_enable_rxirq' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:89:6: warning: symbol 'msgdma_disable_txirq' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:95:6: warning: symbol 'msgdma_enable_txirq' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:101:6: warning: symbol 'msgdma_clear_rxirq' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:107:6: warning: symbol 'msgdma_clear_txirq' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:114:5: warning: symbol 'msgdma_tx_buffer' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:129:5: warning: symbol 'msgdma_tx_completions' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:154:5: warning: symbol 'msgdma_add_rx_desc' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:181:5: warning: symbol 'msgdma_rx_status' was not declared. Should it be static? Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Vince Bridgers <vbridgers2013@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-30Altera TSE: Fix DMA secriptor length initializationTobias Klauser1-37/+37
sgdma_descrip is a function name as well as the name of a struct. In sgdma_initialize(), we should initialize the descriptor length field with the actual length of a descriptor not with the size of the function. In order to prevent such things from happening in the future, rename the function to sgdma_setup_descrip(). Found by sparse which yields the following warning: drivers/net/ethernet/altera/altera_sgdma.c:74:30: warning: expression using sizeof on a function Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-30rtl8192cu: Fix unbalanced irq enable in error path of rtl92cu_hw_init()Ben Hutchings1-1/+1
Fixes: a53268be0cb9 ('rtlwifi: rtl8192cu: Fix too long disable of IRQs') Cc: stable@vger.kernel.org Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-30rtlwifi: rtl8192se: Fix regression due to commit 1bf4bbbLarry Finger1-0/+6
Beginning with kernel 3.13, this driver fails on some systems. The problem was bisected to: Commit 1bf4bbb4024dcdab5e57634dd8ae1072d42a53ac Author: Felix Fietkau <nbd@openwrt.org> Title: mac80211: send control port protocol frames to the VO queue There is noting wrong with the above commit. The regression occurs because V0 queue on RTL8192SE cards uses priority 6, not the usual 7. The fix is to modify the rtl8192se routine that sets the correct transmit queue. Bug: https://bugzilla.kernel.org/show_bug.cgi?id=74541 Reported-by: Alex Miller <almiller_1@yahoo.co.uk> Tested-by: Alex Miller <almiller_1@yahoo.co.uk> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [3.13+] Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-30ath9k: remove tid->paused flagFelix Fietkau3-17/+3
There are some corner cases where the driver could get stuck with a full tid queue that is paused, leading to a software tx queue hang. Since the tx queueing rework, pausing per-tid queues on aggregation session setup is no longer necessary. The driver will assign sequence numbers to buffered frames when a new session is established, in order to get the correct starting sequence number. mac80211 prevents new frames from entering the queue during setup. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-30ath9k_hw: do not lower ANI setting below default on AR913xFelix Fietkau1-0/+6
When the amount of noise fluctuates strongly, low immunity settings can sometimes disrupt signal detection on AR913x chips. When that happens, no OFDM/CCK errors are reported anymore, and ANI tunes the radio to the lowest immunity settings. Usually rx/tx fails as well in that case. To fix this, keep noise immunity settings at or above ANI default level, which will keep radio parameters at or above INI values. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-28net: bonding: Fix format string mismatch in bond_sysfs.cMasanari Iida1-1/+1
Fix format string mismatch in bonding_show_min_links(). Signed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-28net: ipv6: more places need LOOPBACK_IFINDEX for flowi6_iifJulian Anastasov3-1/+4
To properly match iif in ip rules we have to provide LOOPBACK_IFINDEX in flowi6_iif, not 0. Some ip6mr_fib_lookup and fib6_rule_lookup callers need such fix. Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-27net: sctp: Don't transition to PF state when transport has exhausted ↵Karl Heiss1-4/+3
'Path.Max.Retrans'. Don't transition to the PF state on every strike after 'Path.Max.Retrans'. Per draft-ietf-tsvwg-sctp-failover-03 Section 5.1.6: Additional (PMR - PFMR) consecutive timeouts on a PF destination confirm the path failure, upon which the destination transitions to the Inactive state. As described in [RFC4960], the sender (i) SHOULD notify ULP about this state transition, and (ii) transmit heartbeats to the Inactive destination at a lower frequency as described in Section 8.3 of [RFC4960]. This also prevents sending SCTP_ADDR_UNREACHABLE to the user as the state bounces between SCTP_INACTIVE and SCTP_PF for each subsequent strike. Signed-off-by: Karl Heiss <kheiss@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-27slip: fix spinlock variantOliver Hartkopp1-3/+3
With commit cc9fa74e2a ("slip/slcan: added locking in wakeup function") a formerly missing locking was added to slip.c and slcan.c by Andre Naujoks. Alexander Stein contributed the fix 367525c8c2 ("can: slcan: Fix spinlock variant") as the kernel lock debugging advised to use spin_lock_bh() instead of just using spin_lock(). This fix has to be applied to the same code section in slip.c for the same reason too. Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-27Merge branch 'qmi_wwan'David S. Miller1-0/+28
Bjørn Mork says: ==================== qmi_wwan: adding a few new devices Adding some new and some old QMI devices. A similar series for usb-serial support will be posted as well. These new device ID patches should also go to all maintained stable kernels where they apply. I believe that should be stable-3.10 and newer. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-27net: qmi_wwan: add a number of Dell devicesBjørn Mork1-0/+5
Dan writes: "The Dell drivers use the same configuration for PIDs: 81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card 81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card 81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card 81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card 81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card These devices are all clearly Sierra devices, but are also definitely Gobi-based. The A8 might be the MC7700/7710 and A9 is likely a MC7750. >From DellGobi5kSetup.exe from the Dell drivers: usbif0: serial/firmware loader? usbif2: nmea usbif3: modem/ppp usbif8: net/QMI" Reported-by: AceLan Kao <acelan.kao@canonical.com> Reported-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-27net: qmi_wwan: add a number of CMOTech devicesBjørn Mork1-0/+16
A number of older CMOTech modems are based on Qualcomm chips and exporting a QMI/wwan function. Reported-by: Lars Melin <larsm17@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-27net: qmi_wwan: add Alcatel L800MABjørn Mork1-0/+1
Device interface layout: 0: ff/ff/ff - serial 1: ff/00/00 - serial AT+PPP 2: ff/ff/ff - QMI/wwan 3: 08/06/50 - storage Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-27net: qmi_wwan: add Olivetti Olicard 500Bjørn Mork1-0/+1
Device interface layout: 0: ff/ff/ff - serial 1: ff/ff/ff - serial AT+PPP 2: 08/06/50 - storage 3: ff/ff/ff - serial 4: ff/ff/ff - QMI/wwan Reported-by: Julio Araujo <julio.araujo@wllctel.com.br> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2025-02-14 04:57:50 +0000