| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Sony makes custome tuners for its GigaPocket line of ivtv based capture
cards. This adds an entry to the tuner-types list for such tuners.
Parameters are based on experiments by Eric Anderson <rico99@sbcglobal.net>.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
ivtv_api_get_data() was performing more PCI MMIO than needed, resulting
often in it accounting for more than half the total time spent in
ivtv_irq_handler(). Now it only reads at most 7 of the 16 mailbox data words
over the PCI bus, and in some instances only 2 or 3 data words as needed.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Adding Makefile and Kconfig for ISIF driver
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Enhancements to support DM365 ISP5 and VPSS module configuration.
Also cleaned up the driver by removing redundant variables.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This is the source file for ISIF driver on DM365. ISIF driver is equivalent
to CCDC driver on DM355 and DM644x. This driver is tested for YUV capture from
TVP514x driver. This patch contains the header files required for this driver.
Reviewed-by: Nori, Sekhar <nsekhar@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This is the header file for ISIF driver on DM365. ISIF driver is equivalent
to CCDC driver on DM355 and DM644x. This driver is tested for
YUV capture from TVP514x driver. This patch contains the header files required
for this driver.
Reviewed-by: Nori, Sekhar <nsekhar@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch adds following changes:-
1) add sub device configuration data for TVP5146 used by vpfe capture
2) registers platform devices for vpfe_capture, isif and vpss
3) defines hardware resources for the devices listed under 2)
4) defines clock aliase for isif driver
5) adding setup_pinmux() for isif
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
We know that the 300msec settling time after starting the digitizer is
only really needed when the digitizer is a SAA7115. So if we're not
using a SAA7115, skip the delay.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
After implementing a 300msec wait between digitizer start and encoder
start, it has been determined that we don't need to wait quite as long
before configuring the encoder. This reduces the wait period from
100msec back to 50msec.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Martin Dauskardt <martin.dauskardt@gmx.de> has determined that the
encoder has a much better chance of starting cleanly if we
deliberately hold off starting it util the video digitizer has had a
chance to run for at least 300msec first. These changes implement an
enforced 300msec wait in the state machine that orchestrates streaming
start / stop.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
CC: Jonathan Corbet <corbet@lwn.net>
CC: Reviewed-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Videobuf is a moderately complex API which most V4L2 drivers should use,
but its documentation is...sparse. This document attempts to improve the
situation.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Reviewed-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The media spec contains several errors in the description of the
I/O streaming ioctls, in particular with respect to the userptr
I/O method.
The most important change is that you really need to set count
and index in v4l2_requestbuffer and v4l2_buffer when dealing with
user pointer streaming.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When the saa7111 driver was merged into saa7115 several bugs were introduced,
in particular with the saa7111a support as is used in the mxb.c driver.
This patch fixes the saa7111a support. This was tested with the mxb driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
v4l2_device_register needs to be called before the i2c subdevs are loaded.
However, it was called afterwards in the saa7146 driver. This caused an oops
when loading the mxb and hexium drivers. The vv_init function is now split
into two: one registers the v4l2_device, the other does the rest of the
initialization. The three drivers that depend on this have been updated to
call the new vv_devinit function.
Thanks to Michael Hunold for reporting this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The function return value wasn't checked due to a missing variable
assignment.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The Asus EeePC T91 integrated webcam exposes a gain control in the
processing unit but stalls when the control is queried. Blacklist the
gain control for that camera.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When setting a control, the V4L2 specification requires drivers to
either clamp the control value to the [minimum, maximum] range or return
the -ERANGE error.
Fix the driver to clamp control values to the valid range in
uvc_ctrl_set() and make sure the value differs from the minimum by an
integer multiple of step.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
menu index
The V4L2 specification states that out of bounds control values must
either be clamped to the valid range or result in a -ERANGE error code.
Fix the driver to return -ERANGE instead of -EINVAL when setting a menu
control to an invalid value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Replace the UVC_GUID_FORMAT and UVC_GUID_ARGS macros with the new %pUl
printk format specifier.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This fixes timeout issues with some Logitech webcams. The timeout value
seems to match the one used in the Logitech Windows driver, so no
further increase should be necessary.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Ensure that volume values are always in the allowed range. Otherwise,
it would be possible to set other bits in the AUD_VOL_CTL register or to
get a wrong sign in the AUD_BAL_CTL register.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch addes timb-radio to all configurations of the timberdale MFD.
Connected to the FPGA is a TEF6862 tuner and a SAA7706H DSP, the I2C
board info of these devices is passed via the timb-radio platform data.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: sameo@linux.intel.com
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The parenthesis was misplaced, tmp is set to 0 or break occurs,
while debugging opera1_usb_i2c_msgxfer() retval was not shown.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
CC: Marco Gittler <g.marco@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
A small mistake on the last patch broke demod s-code setup for
XC3028L (firmware 3.2 and upper). Fix it.
Thanks-to: Stefan Ringel <stefan.ringel@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
There's one reported regression in Australia (DTV7) and some
reported troubles with newer firmwares found on xc3028l chips.
Rework the logic to improve tuner on those cases.
Thanks-to: Robert Lowery <rglowery@exemail.com.au>
Thanks-to: Stefan Ringel <stefan.ringel@arcor.de>
Tested-by: Robert Lowery <rglowery@exemail.com.au>
CC: stable.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add a new module parameter "disable_ir" to disable IR support. Several
other drivers do that already, and this can be very handy for
debugging purposes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
I succeeded in running Cinergy Hybrid T USB XS FR in both modes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fix sparse warnings in media/dvb/frontends:
drivers/media/dvb/frontends/dibx000_common.c:177:13: warning: non-ANSI function declaration of function 'systime'
drivers/media/dvb/frontends/tda665x.c:136:55: warning: right shift by bigger than source value
[mchehab@redhat.com: removed the change at dib0090 since it got fixed by a previous patch]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Userspace is allowed to coalesce events between SYNCs. And since the code
emits UP right after DOWN for the same key, it may be missed
(up+down=nothing). Add an extra sync in between UP and DOWN events to disable
the coalesce.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
I don't know if there are applications which rely on this name,
but after all it's a spelling mistake.
Signed-off-by: Lars Hanisch <dvb@cinnamon-sage.de>
CC: Janne Granau <j@jannau.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Franklin Meng <fmeng2002@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
RADIO_TIMBERDALE selects RADIO_SAA7706H, but RADIO_SAA7706H
depends on I2C, so make RADIO_TIMBERDALE depend on I2C also;
otherwise there are build errors:
drivers/media/radio/saa7706h.c:139: error: implicit declaration of function 'i2c_master_send'
drivers/media/radio/saa7706h.c:148: error: implicit declaration of function 'i2c_transfer'
drivers/media/radio/saa7706h.c:372: error: implicit declaration of function 'i2c_check_functionality'
drivers/media/radio/saa7706h.c:375: error: implicit declaration of function 'i2c_adapter_id'
drivers/media/radio/saa7706h.c:438: error: implicit declaration of function 'i2c_add_driver'
drivers/media/radio/saa7706h.c:443: error: implicit declaration of function 'i2c_del_driver'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Mocean Laboratories <info@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When CONFIG_PM is not enabled, tlg2300 has build errors,
so handle that case, mostly via stubs.
drivers/media/video/tlg2300/pd-alsa.c:237: error: 'struct poseidon' has no member named 'msg'
drivers/media/video/tlg2300/pd-main.c:412: error: implicit declaration of function 'find_old_poseidon'
drivers/media/video/tlg2300/pd-main.c:418: error: implicit declaration of function 'set_map_flags'
drivers/media/video/tlg2300/pd-main.c:462: error: implicit declaration of function 'get_pd'
Cc: linux-next@vger.kernel.org, LKML <linux-kernel@vger.kernel.org>, linux-media@vger.kernel.org
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Huang Shijie <shijie8@gmail.com>
Cc: Kang Yong <kangyong@telegent.com>
Cc: Zhang Xiaobing <xbzhang@telegent.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fix mfd/timberdale build error -- add depends GPIOLIB.
include/linux/spi/max7301.h:14: error: field 'chip' has incomplete type
build-r7353.out:make[3]: *** [drivers/mfd/timberdale.o] Error 1
Repairs
commit ff7a26e08a16bb31158d830dbf60db2ff47019ab
Author: Richard R<C3><B6>jfors <richard.rojfors@pelagicore.com>
AuthorDate: Thu Feb 4 08:18:52 2010 -0300
Commit: Mauro Carvalho Chehab <mchehab@redhat.com>
CommitDate: Fri Feb 5 12:25:37 2010 -0200
V4L/DVB: mfd: Add support for the timberdale FPGA
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Richard Rojfors <richard.rojfors@pelagicore.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch provides menu configuration options for the TVP7002
decoder driver in DM365. Includes only TVP7002.
Signed-off-by: Santiago Nunez-Corrales <santiago.nunez@ridgerun.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
> On Mon, 22 Feb 2010 08:21:44 -0800 Randy Dunlap wrote:
> drivers/media/video/tvp7002.c:896: error: 'struct tvp7002' has no member named 'registers'
>
> so where are these registers??
Hmm, that code is a remnant from older revisions of this driver. Unfortunately,
when I compiled this driver before creating my pull request I forgot to turn on
the CONFIG_VIDEO_ADV_DEBUG option and so I never saw it.
Also fixed the g_register function: it never returned a register
value in the original code.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch provides the implementation of the TVP7002 decoder
driver for DM365. Implemented using the V4L2 DV presets API.
Removed shadow register values. Testing shows that the device
needs not to be powered down and up for correct behaviour.
Improved readability. Uses helper function for preset information.
[mchehab@redhat.com: Fix bad Whitespacing]
Signed-off-by: Santiago Nunez-Corrales <santiago.nunez@ridgerun.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch provides the required definitions for the TVP7002 driver
in DM365.
Signed-off-by: Santiago Nunez-Corrales <santiago.nunez@ridgerun.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch provides required chip identification definitions
within v4l2. Included only definitions for TVP7002.
Signed-off-by: Santiago Nunez-Corrales <santiago.nunez@ridgerun.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
drivers/media/dvb/dvb-usb/az6027.c:390: warning: excess elements in struct initializer
drivers/media/dvb/dvb-usb/az6027.c:390: warning: (near initialization for ‘az6027_rc_keys[0]’)
drivers/media/dvb/dvb-usb/az6027.c:391: warning: excess elements in struct initializer
drivers/media/dvb/dvb-usb/az6027.c:391: warning: (near initialization for ‘az6027_rc_keys[1]’)
drivers/media/dvb/dvb-usb/az6027.c:759: warning: ‘az6027_read_mac_addr’ defined but not used
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This reverts commit 1e08370814e8902074d59cc57f2b4c1a62f00ee8.
Patch were wrongly applied.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
parameters, instead of 2"
This reverts commit 234497b022c464532976b8a12614819bcf67f41b.
Patch were wrongly applied.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Just pass VIDIOC_S_PARM and VIDIOC_G_PARM down to host drivers. So far no
special handling in soc-camera core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
