summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2014-07-25scsi: centralize command re-queueing in scsi_dispatch_fnChristoph Hellwig2-26/+18
Make sure we only have the logic for requeing commands in one place. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Webb Scales <webbnh@hp.com> Acked-by: Jens Axboe <axboe@kernel.dk> Tested-by: Bart Van Assche <bvanassche@acm.org> Tested-by: Robert Elliott <elliott@hp.com>
2014-07-25scsi: split __scsi_queue_insertChristoph Hellwig1-18/+26
Factor out a helper to set the _blocked values, which we'll reuse for the blk-mq code path. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Webb Scales <webbnh@hp.com> Acked-by: Jens Axboe <axboe@kernel.dk> Tested-by: Bart Van Assche <bvanassche@acm.org> Tested-by: Robert Elliott <elliott@hp.com>
2014-07-25scsi: add scsi_setup_cmnd helperChristoph Hellwig1-18/+22
Factor out command setup code that will be shared with the blk-mq code path. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Webb Scales <webbnh@hp.com>
2014-07-17scsi: mark scsi_setup_blk_pc_cmnd staticChristoph Hellwig2-4/+1
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
2014-07-17sd: split sd_init_commandChristoph Hellwig1-29/+29
Factor out a function to initialize regular read/write commands and leave sd_init_command as a simple dispatcher to the different prepare routines. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
2014-07-17sd: retry discard commandsChristoph Hellwig1-1/+1
Currently cmd->allowed is initialized from rq->retries for discard commands, but retries is always 0 for non-BLOCK_PC requests. Set it to the standard number of retries instead. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
2014-07-17sd: retry write same commandsChristoph Hellwig1-1/+1
Currently cmd->allowed is initialized from rq->retries for write same commands, but retries is always 0 for non-BLOCK_PC requests. Set it to the standard number of retries instead. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
2014-07-17sd: don't use scsi_setup_blk_pc_cmnd for discard requestsChristoph Hellwig1-19/+31
Simplify handling of discard requests by setting up the command directly instead of initializing request fields and then calling scsi_setup_blk_pc_cmnd to propagate the information into the command. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
2014-07-17sd: don't use scsi_setup_blk_pc_cmnd for write same requestsChristoph Hellwig1-16/+28
Simplify handling of write same requests by setting up the command directly instead of initializing request fields and then calling scsi_setup_blk_pc_cmnd to propagate the information into the command. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Webb Scales <webbnh@hp.com>
2014-07-17sd: don't use scsi_setup_blk_pc_cmnd for flush requestsChristoph Hellwig1-7/+13
Simplify handling of flush requests by setting up the command directly instead of initializing request fields and then calling scsi_setup_blk_pc_cmnd to propagate the information into the command. Also rename scsi_setup_flush_cmnd to sd_setup_flush_cmnd for consistency. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
2014-07-17scsi: set sc_data_direction in common codeChristoph Hellwig3-11/+7
The data direction fiel in the SCSI command is derived only from the block request structure. Move setting it up into common code instead of duplicating it in the ULDs. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
2014-07-17scsi: restructure command initialization for TYPE_FS requestsChristoph Hellwig4-14/+14
We should call the device handler prep_fn for all TYPE_FS requests, not just simple read/write calls that are handled by the disk driver. Restructure the common I/O code to call the prep_fn handler and zero out the CDB, and just leave the call to scsi_init_io to the ULDs. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
2014-07-17scsi: move the nr_phys_segments assert into scsi_init_ioChristoph Hellwig1-11/+5
scsi_init_io should only be called for requests that transfer data, so move the assert that a request has segments from the callers into scsi_init_io. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
2014-07-17scsi_lib: remove the description string in scsi_io_completion()Maurizio Lombardi1-36/+4
During IO with fabric faults, one generally sees several "Unhandled error code" messages in the syslog as shown below: sd 4:0:6:2: [sdbw] Unhandled error code sd 4:0:6:2: [sdbw] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK sd 4:0:6:2: [sdbw] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 end_request: I/O error, dev sdbw, sector 0 This comes from scsi_io_completion (in scsi_lib.c) while handling error codes other than DID_RESET or not deferred sense keys i.e. this is actually handled by the SCSI mid layer. But what gets displayed here is "Unhandled error code" which is quite misleading as it indicates something that is not addressed by the mid layer. The description string is based on the sense key and sometimes on the additional sense code; since the ACTION_FAIL case always prints the sense key and the additional sense code, this patch removes the description string completely because it does not add useful information. Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi: cleanup switch in scsi_adjust_queue_depthDouglas Gilbert1-4/+6
While checking what scsi_adjust_queue_depth() did I thought its switch statement could be clearer: - remove redundant assignment (to sdev->queue_depth) - re-order cases (thus removing the fall-through) Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Robert Elliott <elliott@hp.com> Tested-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi: remove various exports that were only used by scsi_tgtChristoph Hellwig4-16/+5
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
2014-07-17tgt: defconfig cleanupBart Van Assche40-48/+0
Because of the removal of the scsi_tgt kernel module, the kbuild variables CONFIG_SCSI_TGT, CONFIG_SCSI_SRP_TGT_ATTRS and CONFIG_SCSI_FC_TGT_ATTRS are obsolete. This patch removes these variables. This patch is the result of the following command: find -name '*defconfig' | while read f; do grep -vwE 'CONFIG_SCSI_TGT|CONFIG_SCSI_SRP_TGT_ATTRS|CONFIG_SCSI_FC_TGT_ATTRS|CONFIG_SRP' $f >/tmp/t && mv /tmp/t $f; done Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
2014-07-17tgt: removalBart Van Assche12-1333/+0
Now that the ibmvstgt driver as the only user of scsi_tgt is gone, the scsi_tgt kernel module, the CONFIG_SCSI_TGT, CONFIG_SCSI_SRP_TGT_ATTRS and CONFIG_SCSI_FC_TGT_ATTRS kbuild variable, the scsi_host_template transfer_response method are no longer needed. [hch: minor updates to the current tree, changelog update] Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
2014-07-17libsrp: removalChristoph Hellwig4-536/+0
Remove the libsrp module which was only used by the now removed ibmvstgt driver. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
2014-07-17ibmvstgt: removeChristoph Hellwig4-1017/+0
The IBM virtual SCSI protocol has been obsoleted by ibmvfc, and there are no reported of the driver left. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
2014-07-17scsi: use dev_printk variants where possibleHannes Reinecke5-139/+157
Using dev_printk variants prefixes the logging message with the originating device, which makes debugging easier. Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi: use dev_printk() variants for ioctlHannes Reinecke1-6/+11
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi: Implement st_printk()Hannes Reinecke1-294/+311
Update the st driver to use dev_printk() variants instead of plain printk(); this will prefix logging messages with the appropriate device. Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi: Implement ch_printk()Hannes Reinecke1-5/+9
Update the ch driver to use dev_printk() variants instead of plain printk(); this will prefix logging messages with the appropriate device. Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi: Implement sg_printk()Hannes Reinecke1-68/+95
Update the sg driver to use dev_printk() variants instead of plain printk(); this will prefix logging messages with the appropriate device. Signed-off-by: Hannes Reinecke <hare@suse.de> Acked-by: Doug Gilbert <dgilbert@interlog.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi: Implement sr_printk()Hannes Reinecke4-57/+70
Update the sr driver to use dev_printk() variants instead of plain printk(); this will prefix logging messages with the appropriate device. Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi_scan: Fixup scsilun_to_int()Hannes Reinecke1-12/+10
scsilun_to_int() has an error which prevents it from generating correct LUN numbers for 64bit values. Also we should remove the misleading comment about portions of the LUN being ignored; the initiator should treat the LUN as an opaque value. And, finally, the example given should use the correct prefix (here: extended flat space addressing scheme). This patch includes the modifications suggested by Bart van Assche. Cc: Bart van Assche <bvanassche@acm.org> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: James Bottomley <jbottomley@parallels.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi: use 64-bit value for 'max_luns'Hannes Reinecke14-22/+30
Now that we're using 64-bit LUNs internally we need to increase the size of max_luns to 64 bits, too. Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Christoph Hellwig <hch@infradead.org> Reviewed-by: Ewan Milne <emilne@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17Add module param type 'ullong'Hannes Reinecke2-0/+6
Some driver might want to pass in an 64-bit value, so introduce a module param type 'ullong'. Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Christoph Hellwig <hch@infradead.org> Reviewed-by: Ewan Milne <emilne@redhat.com> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi: use 64-bit LUNsHannes Reinecke86-429/+438
The SCSI standard defines 64-bit values for LUNs, and large arrays employing large or hierarchical LUN numbers become more and more common. So update the linux SCSI stack to use 64-bit LUN numbers. Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Christoph Hellwig <hch@infradead.org> Reviewed-by: Ewan Milne <emilne@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17qla2xxx: Restrict max_lun to 16-bit for older HBAsHannes Reinecke1-1/+6
Older HBAs are only capable of supporting 16-bit LUNs, so we need to make sure to adjust max_lun accordingly. Signed-off-by: Hannes Reinecke <hare@suse.de> Acked-by: Chad Dupuis <chad.dupuis@qlogic.com> Reviewed-by: Ewan Milne <emilne@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi_scan: Restrict sequential scan to 256 LUNsHannes Reinecke2-0/+8
Sequential scan for more than 256 LUNs is very fragile as LUNs might not be numbered sequentially after that point. SAM revisions later than SCSI-3 impose a structure on LUNs larger than 256, making LUN numbers between 256 and 16384 illegal. SCSI-3, however allows for plain 64-bit numbers with no internal structure. So restrict sequential LUN scan to 256 LUNs and add a new blacklist flag 'BLIST_SCSI3LUN' to scan up to max_lun devices. Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Ewan Milne <emilne@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi: Remove CONFIG_SCSI_MULTI_LUNHannes Reinecke6-35/+2
Obsolete; either use 'max_lun' if the host supports only a limited number of LUNs or BLIST_NOLUN if the target has problems addressing more than one LUN. Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Ewan Milne <emilne@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17sg: O_EXCL and other lock handlingDouglas Gilbert1-194/+230
This addresses a problem reported by Vaughan Cao concerning the correctness of the O_EXCL logic in the sg driver. POSIX doesn't defined O_EXCL semantics on devices but "allow only one open file descriptor at a time per sg device" is a rough definition. The sg driver's semantics have been to wait on an open() when O_NONBLOCK is not given and there are O_EXCL headwinds. Nasty things can happen during that wait such as the device being detached (removed). So multiple locks are reworked in this patch making it large and hard to break down into digestible bits. This patch is against Linus's current git repository which doesn't include any sg patches sent in the last few weeks. Hence this patch touches as little as possible that it doesn't need to and strips out most SCSI_LOG_TIMEOUT() changes in v3 because Hannes said he was going to rework all that stuff. The sg3_utils package has several test programs written to test this patch. See examples/sg_tst_excl*.cpp . Not all the locks and flags in sg have been re-worked in this patch, notably sg_request::done . That can wait for a follow-up patch if this one meets with approval. Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
2014-07-17sg: add SG_FLAG_Q_AT_TAIL flagDouglas Gilbert2-2/+8
When the SG_IO ioctl was copied into the block layer and later into the bsg driver, subtle differences emerged. One difference is the way injected commands are queued through the block layer (i.e. this is not SCSI device queueing nor SATA NCQ). Summarizing: - SG_IO in the block layer: blk_exec*(at_head=false) - sg SG_IO: at_head=true - bsg SG_IO: at_head=true Some time ago Boaz Harrosh introduced a sg v4 flag called BSG_FLAG_Q_AT_TAIL to override the bsg driver default. This patch does the equivalent for the sg driver. ChangeLog: Introduce SG_FLAG_Q_AT_TAIL flag to cause commands to be injected into the block layer with at_head=false. Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17sg: relax 16 byte cdb restrictionDouglas Gilbert2-84/+53
- remove the 16 byte CDB (SCSI command) length limit from the sg driver by handling longer CDBs the same way as the bsg driver. Remove comment from sg.h public interface about the cmd_len field being limited to 16 bytes. - remove some dead code caused by this change - cleanup comment block at the top of sg.h, fix urls Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17sd: Limit transfer lengthMartin K. Petersen2-1/+18
Until now the per-command transfer length has exclusively been gated by the max_sectors parameter in the scsi_host template. Given that the size of this parameter has been bumped to an unsigned int we have to be careful not to exceed the target device's capabilities. If the if the device specifies a Maximum Transfer Length in the Block Limits VPD we'll use that value. Otherwise we'll use 0xffffffff for devices that have use_16_for_rw set and 0xffff for the rest. We then combine the chosen disk limit with max_sectors in the host template. The smaller of the two will be used to set the max_hw_sectors queue limit. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17sd: bad return code of init_sdClément Calmels1-0/+2
In init_sd function, if kmem_cache_create or mempool_create_slab_pools calls fail, the error will not be correclty reported because class_register previously set the value of err to 0. Signed-off-by: Clément Calmels <clement.calmels@free.fr> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17sd: notify block layer when using temporary change to cache_typeVaughan Cao1-8/+15
This is a fix for commit 39c60a0948cc06139e2fbfe084f83cb7e7deae3b "sd: fix array cache flushing bug causing performance problems" We must notify the block layer via q->flush_flags after a temporary change of the cache_type to write through. Without this, a SYNCHRONIZE CACHE command will still be generated. This patch factors out a helper that can be called from sd_revalidate_disk and cache_type_store. Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi_debug: allow huge transfer length for read/write commandsAkinobu Mita1-3/+3
This change enables to test read/write commands with huge transfer length such as 1GB. For example: # modprobe scsi_debug dev_size_mb=1024 clustering=1 opts=1 # cat /sys/block/$DEV/queue/max_hw_sectors_kb > \ /sys/block/$DEV/queue/max_sectors_kb # fio --name=test --rw=write --bs=1g --size=1g --filename=/dev/$DEV \ --mem=mmaphuge --direct=1 The data type of max_sectors in scsi_host_template has been extended to unsigned int by the previous change. So we can increase it from 0xffff to 0xffffffff to allow such huge transfer length. Also, this increases sg_tablesize and max_segment_size, otherwise the maximum transfer length is limited to 64MB. (sg_tablesize * max_segment_size = 256 * 256KB) Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Acked by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi: increase upper limit for max_sectorsAkinobu Mita1-2/+2
max_sectors in struct Scsi_Host specifies maximum number of sectors allowed in a single SCSI command. The data type of max_sectors is unsigned short, so the maximum transfer length per SCSI command is limited to less than 256MB in 4096-bytes sector size. (0xffff * 4096) This commit increases the SCSI mid level's limitation for max_sectors upto the block layer's limitation for max_hw_sectors by extending the data type of max_sectors in struct Scsi_Host and scsi_host_template, so that SCSI lower level drivers can specify more than 0xffff. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17sd: use READ_16 or WRITE_16 when transfer length is greater than 0xffffAkinobu Mita1-4/+1
This change makes the scsi disk driver handle the requests whose transfer length is greater than 0xffff with READ_16 or WRITE_16. However, this is a preparation for extending the data type of max_sectors in struct Scsi_Host and scsi_host_template. So, it is impossible to happen this condition for now, because SCSI low-level drivers can not specify max_sectors greater than 0xffff due to the data type limitation. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17sg: prevent integer overflow when converting from sectors to bytesAkinobu Mita1-4/+13
This prevents integer overflow when converting the request queue's max_sectors from sectors to bytes. However, this is a preparation for extending the data type of max_sectors in struct Scsi_Host and scsi_host_template. So, it is impossible to happen this integer overflow for now, because SCSI low-level drivers can not specify max_sectors greater than 0xffff due to the data type limitation. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Acked by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi: remove two cancel_delayed_work() calls from the mid-layerBart Van Assche2-2/+2
scsi_put_command() is either invoked before blk_start_request() or after block layer processing has completed. scsi_cmnd.abort_work is scheduled from inside the SCSI timeout handler. The block layer guarantees that either the regular completion handler (softirq_done_fn()) or the timeout handler (rq_timed_out_fn()) is invoked but not both. This means that scsi_put_command() is never invoked while abort_work is scheduled. Hence remove the cancel_delayed_work() call from scsi_put_command(). Similarly, scsi_abort_command() is only invoked from the SCSI timeout handler. If scsi_abort_command() is invoked for a SCSI command with the SCSI_EH_ABORT_SCHEDULED flag set this means that scmd_eh_abort_handler() has already invoked scsi_queue_insert() and hence that scsi_cmnd.abort_work is no longer pending. Hence also remove the cancel_delayed_work() call from scsi_abort_command(). Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17scsi: handle flush errors properlyJames Bottomley1-0/+8
Flush commands don't transfer data and thus need to be special cased in the I/O completion handler so that we can propagate errors to the block layer and filesystem. Signed-off-by: James Bottomley <JBottomley@Parallels.com> Reported-by: Steven Haber <steven@qumulo.com> Tested-by: Steven Haber <steven@qumulo.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-07-17Merge tag 'stable/for-linus-3.16-rc5-tag' of ↵Linus Torvalds2-8/+9
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull Xen fixes from Konrad Rzeszutek Wilk: "Two fixes found during migration of PV guests. David would be the one doing this pull but he is on vacation. Fixes: - fix console deadlock when resuming PV guests - fix regression hit when ballooning and resuming PV guests" * tag 'stable/for-linus-3.16-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen/balloon: set ballooned out pages as invalid in p2m xen/manage: fix potential deadlock when resuming the console
2014-07-17Merge tag 'trace-fixes-v3.16-rc5-v2' of ↵Linus Torvalds4-8/+19
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace Pull tracing fixes from Steven Rostedt: "A few more fixes for ftrace infrastructure. I was cleaning out my INBOX and found two fixes from zhangwei from a year ago that were lost in my mail. These fix an inconsistency between trace_puts() and the way trace_printk() works. The reason this is important to fix is because when trace_printk() doesn't have any arguments, it turns into a trace_puts(). Not being able to enable a stack trace against trace_printk() because it does not have any arguments is quite confusing. Also, the fix is rather trivial and low risk. While porting some changes to PowerPC I discovered that it still has the function graph tracer filter bug that if you also enable stack tracing the function graph tracer filter is ignored. I fixed that up. Finally, Martin Lau, fixed a bug that would cause readers of the ftrace ring buffer to block forever even though it was suppose to be NONBLOCK" This also includes the fix from an earlier pull request: "Oleg Nesterov fixed a memory leak that happens if a user creates a tracing instance, sets up a filter in an event, and then removes that instance. The filter allocates memory that is never freed when the instance is destroyed" * tag 'trace-fixes-v3.16-rc5-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: ring-buffer: Fix polling on trace_pipe tracing: Add TRACE_ITER_PRINTK flag check in __trace_puts/__trace_bputs tracing: Fix graph tracer with stack tracer on other archs tracing: Add ftrace_trace_stack into __trace_puts/__trace_bputs tracing: instance_rmdir() leaks ftrace_event_file->filter
2014-07-16Merge tag 'for-linus-20140716' of git://git.infradead.org/linux-mtdLinus Torvalds3-2/+49
Pull MTD fixes from Brian Norris: - Fix ELM suspend/resume - Reduce warnings if NAND ECC is too weak - Add CFI support for Sharp LH28F640BF NOR The last fix is coming in because other commits in the 3.16 cycle depended on this support. * tag 'for-linus-20140716' of git://git.infradead.org/linux-mtd: mtd: cfi_cmdset_0001.c: add support for Sharp LH28F640BF NOR mtd: nand: reduce the warning noise when the ECC is too weak mtd: devices: elm: fix elm_context_save() and elm_context_restore() functions
2014-07-16Merge branch 'sched-urgent-for-linus' of ↵Linus Torvalds4-8/+8
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull scheduler fixes from Ingo Molnar: "A cpufreq lockup fix and a compiler warning fix" * 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched: Fix compiler warnings x86, tsc: Fix cpufreq lockup
2014-07-16Merge branch 'perf-urgent-for-linus' of ↵Linus Torvalds4-38/+48
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull perf fixes from Ingo Molnar: "Tooling fixes and an Intel PMU driver fixlet" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf: Do not allow optimized switch for non-cloned events perf/x86/intel: ignore CondChgd bit to avoid false NMI handling perf symbols: Get kernel start address by symbol name perf tools: Fix segfault in cumulative.callchain report
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-24 11:22:34 +0000