Age | Commit message (Collapse) | Author | Files | Lines |
|
Call regulator_[get|set]_voltage_sel_regmap instead of open code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Ying-Chun Liu <paulliu@debian.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
By setting linear_min_sel to anatop_reg->min_bit_val, we can avoid
adjust the anatop_reg->min_bit_val offset in [set|get]_voltage_sel.
With this chance we can refactor this driver to use
regulator_[get|set]_voltage_sel_regmap.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Ying-Chun Liu <paulliu@debian.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-min
Conflicts:
drivers/regulator/tps51632-regulator.c
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This driver can be converted to use linear_min_sel and
regulator_[map|list]_voltage_linear.
Below shows the equation (from Datasheet) for each LDOs.
For AUTOOUT:
VO(prog) = 0.625 + auto_out x 0.025 V; e.g.
(00000000 to 00101110: reserved)
00101111: 1.8 V (min)
01010011: 2.7 V
01101010: 3.275 V
01101011: 3.300 V
01101100: 3.325 V
01111111 : 3.800 V (max)
The linear mapping start from 0x2f selector.
Thus we convert this equation to:
VO(prog) = 1.8 + (selector - linear_min_sel) x 0.025 V
(min_uV = 1800000, uV_step = 25000, linear_min_sel = 0x2f)
For DOWNxOUT:
VO(prog) = 0.625 + downx_out x 0.025 V; e.g.
00000000 : 0.625 V (min)
00010111 : 1.200 V
00101111 : 1.800 V
01011111 : 3.000 V (max)
For xLDOOUT:
VO(prog) = 0.9 + xldo_out x 0.1 V; e.g.
00000: 0.9 V
00001: 1.0 V
11000 : 3.3 V
11011 : 3.6 V
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
When tps->enable_pwm_dvfs is true, write to TPS51632_VOLTAGE_BASE_REG rather
than TPS51632_VOLTAGE_SELECT_REG.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-min
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Some drivers (at least 3 drivers) have such variant of linear mapping that
the first few selectors are invalid and the reset are linear mapping.
Let's support this case in core.
This patch adds linear_min_sel in struct regulator_desc,
so we can allow specific minimal selector for starting linear mapping.
Then extends regulator_[map|list]_voltage_linear() to support this feature.
Note that for selectors less than min_linear_index, we need count them to
n_voltages so regulator_list_voltage() won't fail while checking the boundary
for selector before calling list_voltage callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc EEH bugfixes from Benjamin Herrenschmidt.
Two one-liner fixes for the new EEH code.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/eeh: Do not invalidate PE properly
powerpc/pseries: Fix oops with MSIs when missing EEH PEs
|
|
Pull MIPS fixes from Ralf Baechle:
"Three issues fixed accross the field:
- Some functions that were recently outlined as part of a preemption
fix were causing problems with function tracing.
- The recently merged in-kernel MPI library uses very outdated
headers that contain MIPS-specific code which won't build on with
gcc 4.4 or newer.
- The MIPS non-NUMA memory initialization was making only a very
half-baked attempt at merging adjacent memory ranges. This kept
the code simple enough but is now causing issues with kexec."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MPI: Fix compilation on MIPS with GCC 4.4 and newer
MIPS: Fix crash that occurs when function tracing is enabled
MIPS: Merge overlapping bootmem ranges
|
|
While the EEH does recovery on the specific PE that has PCI errors,
the PCI devices belonging to the PE will be removed and the PE will
be marked as invalid since we still need the information stored in
the PE. We only invalidate the PE when it doesn't have associated
EEH devices and valid child PEs. However, the code used to check
that is wrong. The patch fixes that.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound build error fix from Takashi Iwai:
"Only a single commit for fixing the build error without CONFIG_PM in
hda driver."
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix build without CONFIG_PM
|
|
I forgot this again... codec->in_pm is in #ifdef CONFIG_PM
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 arch fixes from Peter Anvin:
"Here is a collection of fixes for 3.7-rc7. This is a superset of
tglx' earlier pull request."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64: Fix ordering of CFI directives and recent ASM_CLAC additions
x86, microcode, AMD: Add support for family 16h processors
x86-32: Export kernel_stack_pointer() for modules
x86-32: Fix invalid stack address while in softirq
x86, efi: Fix processor-specific memcpy() build error
x86: remove dummy long from EFI stub
x86, mm: Correct vmflag test for checking VM_HUGETLB
x86, amd: Disable way access filter on Piledriver CPUs
x86/mce: Do not change worker's running cpu in cmci_rediscover().
x86/ce4100: Fix PCI configuration register access for devices without interrupts
x86/ce4100: Fix reboot by forcing the reboot method to be KBD
x86/ce4100: Fix pm_poweroff
MAINTAINERS: Update email address for Robert Richter
x86, microcode_amd: Change email addresses, MAINTAINERS entry
MAINTAINERS: Change Boris' email address
EDAC: Change Boris' email address
x86, AMD: Change Boris' email address
|
|
Pull MTD fixes from David Woodhouse:
"The most important part of this is that it fixes a regression in
Samsung NAND chip detection, introduced by some rework which went into
3.7. The initial fix wasn't quite complete, so it's in two parts. In
fact the first part is committed twice (Artem committed his own copy
of the same patch) and I've merged Artem's tree into mine which
already had that fix.
I'd have recommitted that to make it somewhat cleaner, but figured by
this point in the release cycle it was better to merge *exactly* the
commits which have been in linux-next.
If I'd recommitted, I'd also omit the sparse warning fix. But it's
there, and it's harmless — just marking one function as 'static' in
onenand code.
This also includes a couple more fixes for stable: an AB-BA deadlock
in JFFS2, and an invalid range check in slram."
* tag 'for-linus-20121123' of git://git.infradead.org/mtd-2.6:
mtd: nand: fix Samsung SLC detection regression
mtd: nand: fix Samsung SLC NAND identification regression
jffs2: Fix lock acquisition order bug in jffs2_write_begin
mtd: onenand: Make flexonenand_set_boundary static
mtd: slram: invalid checking of absolute end address
mtd: ofpart: Fix incorrect NULL check in parse_ofoldpart_partitions()
mtd: nand: fix Samsung SLC NAND identification regression
|
|
Pull device tree regression fix from Grant Likely:
"Simple build regression fix for DT device drivers on Sparc. An
earlier change had masked out the of_iomap() helper on SPARC."
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6:
of/address: sparc: Declare of_iomap as an extern function for sparc again
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management update from Rafael Wysocki:
"Fix for an incorrect error condition check in device PM QoS code that
may lead to an Oops from Guennadi Liakhovetski."
* tag 'pm-for-3.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / QoS: fix wrong error-checking condition
|
|
Pull md fixes from NeilBrown:
"Several bug fixes for md in 3.7:
- raid5 discard has problems
- raid10 replacement devices have problems
- bad block lock seqlock usage has problems
- dm-raid doesn't free everything"
* tag 'md-3.7-fixes' of git://neil.brown.name/md:
md/raid10: decrement correct pending counter when writing to replacement.
md/raid10: close race that lose writes lost when replacement completes.
md/raid5: Make sure we clear R5_Discard when discard is finished.
md/raid5: move resolving of reconstruct_state earlier in stripe_handle.
md/raid5: round discard alignment up to power of 2.
md: make sure everything is freed when dm-raid stops an array.
md: Avoid write invalid address if read_seqretry returned true.
md: Reassigned the parameters if read_seqretry returned true in func md_is_badblock.
|
|
Pull block layer fixes from Jens Axboe:
"Distilled down version of bug fixes for 3.7. The patches have been
well tested. If you notice that commit dates are from today, it's
because I pulled less important bits out and shuffled them into the
3.8 mix. Apart from that, no changes, base still the same.
It contains:
- Fix for aoe, don't run request_fn while it's plugged.
- Fix for a regression in floppy since 3.6, which causes problems if
no floppy is found.
- Stable fix for blk_exec(), don't touch a request after it has been
sent to the scheduler (and the device as well).
- Five fixes for various nasties in mtip32xx."
* 'for-linus' of git://git.kernel.dk/linux-block:
block: Don't access request after it might be freed
mtip32xx: Fix padding issue
aoe: avoid running request handler on plugged queue
mtip32xx: fix potential NULL pointer dereference in mtip_timeout_function()
mtip32xx: fix shift larger than type warning
mtip32xx: Fix incorrect mask used for erase mode
mtip32xx: Fix to make lba address correct in big-endian systems
mtip32xx: fix potential crash on SEC_ERASE_UNIT
dm: fix deadlock with request based dm and queue request_fn recursion
floppy: destroy floppy workqueue before cleaning up the queue
|
|
This bug-fix makes sure that of_iomap is defined extern for sparc so that the
sparc-specific implementation of_iomap is once again used when including
include/linux/of_address.h in a sparc context. OF_GPIO that is now available for
sparc relies on this.
The bug was inadvertently introduced in a850a75, "of/address: add empty static
inlines for !CONFIG_OF", that added a static dummy inline for of_iomap when
!CONFIG_OF_ADDRESS. However, CONFIG_OF_ADDRESS is never defined for sparc, but
there is a sparc-specific implementation /arch/sparc/kernel/of_device_common.c.
This fix takes the same approach as 0bce04b that solved the equivalent problem
for of_address_to_resource.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Pull omapdss fixes from Tomi Valkeinen:
"Here are a few OMAPDSS fixes for the next -rc. I'm sending these
directly to you, and quite late, as the fbdev tree maintainer
(Florian) has been busy with his work and hasn't had time to manage
the fb patches."
* tag 'omapdss-for-3.7-rc' of git://gitorious.org/linux-omap-dss2/linux:
OMAPDSS: do not fail if dpll4_m4_ck is missing
OMAPFB: Fix possible null pointer dereferencing
OMAPDSS: HDMI: fix missing unlock on error in hdmi_dump_regs()
omapdss: dss: Fix clocks on OMAP363x
OMAPDSS: DSI: fix dsi_get_dsidev_from_id()
|
|
git://git.pengutronix.de/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Bugfixes for the i2c subsystem.
Except for a few one-liners, there is mainly one revert because of an
overlooked dependency. Since there is no linux-next at the moment, I
did some extra testing, and all was fine for me."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Fix code to free gpios
i2c: omap: ensure writes to dev->buf_len are ordered
Revert "ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints"
i2c: at91: fix SMBus quick command
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The highlight of this update is the fixes for ASoC kirkwood by
Russell. In addition to that, a couple of regression fixes for
HD-audio due to the runtime PM support on 3.7, and other driver-
specific regression fixes like USB MIDI on non-standard USB audio
drivers."
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: snd-usb: properly initialize the sync endpoint
ALSA: hda - Cirrus: Correctly clear line_out_pins when moving to speaker
ALSA: hda - Add support for Realtek ALC292
ASoC: kirkwood-i2s: more pause-mode fixes
ASoC: kirkwood-i2s: fix DMA underruns
ASoC: kirkwood-i2s: fix DCO lock detection
ASoC: kirkwood-dma: don't ignore other irq causes on error
ASoC: kirkwood-dma: fix use of virt_to_phys()
ALSA: hda - Limit runtime PM support only to known Intel chips
ALSA: hda - Fix recursive suspend/resume call
ALSA: ua101, usx2y: fix broken MIDI output
ASoC: arizona: Fix typo - Swap value in 48k_rates[] and 44k1_rates[]
ASoC: bells: Fix up git patch application failure
ASoC: cs4271: free allocated GPIO
|
|
Pull networkign fixes from David Miller:
"Networking bug fixes, Cacio e Pepe edition:
1) BNX2X accidently accesses chip rev specific registers without an
appropriate guard, fix from Ariel Elior.
2) When we removed the routing cache, we set ip_rt_max_size to ~0 just
to keep reporting a value to userspace via sysfs. But the ipv4
IPSEC layer was using this to tune itself which is completely bogus
to now do. Fix from Steffen Klassert.
3) Missing initialization in netfilter ipset code from Jozsef
Kadlecsik.
4) Check CTA_TIMEOUT_NAME length properly in netfilter cttimeout code,
fix from Florian Westphal.
5) After removing the routing cache, we inadvertantly are caching
multicast routes that end up looping back locally, we cannot do
that legitimately any more. Fix from Julian Anastasov.
6) Revert a race fix for 8139cp qemu/kvm that doesn't actually work
properly on real hardware. From Francois Romieu.
7) Fixup errors in example command lines in VXLAN device docs."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
ipv4: do not cache looped multicasts
netfilter: cttimeout: fix buffer overflow
netfilter: ipset: Fix range bug in hash:ip,port,net
xfrm: Fix the gc threshold value for ipv4
|
|
Pull sparc fix from David Miller:
"Bug fix from Al Viro"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: not any error from do_sigaltstack() should fail rt_sigreturn()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull one more ARM SoC fix from Olof Johansson:
"I missed one pull request from Samsung with one fix in the previous
batch. Here it is -- a dma driver fix for an early version of silicon
that they still support."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: PL330 MDMA1 fix for revision 0 of Exynos4210 SOC
|
|
dev_pm_qos_add_request() can return 0, 1, or a negative error code,
therefore the correct error test is "if (error < 0)." Checking just for
non-zero return code leads to erroneous setting of the req->dev pointer
to NULL, which then leads to a repeated call to
dev_pm_qos_add_ancestor_request() in st1232_ts_irq_handler(). This in turn
leads to an Oops, when the I2C host adapter is unloaded and reloaded again
because of the inconsistent state of its QoS request list.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
fix bug where a register which was only meant to be read in 578xx/57712
devices causes a bogus error message to be logged when read from other
devices.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some commands don't work in its example doc. The patch will fix it.
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reverts b01af4579ec41f48e9b9c774e70bd6474ad210db.
The original patch was tested with emulated hardware. Real
hardware chokes.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=47041
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since 4.4 GCC on MIPS no longer recognizes the "h" constraint,
leading to this build failure:
CC lib/mpi/generic_mpih-mul1.o
lib/mpi/generic_mpih-mul1.c: In function 'mpihelp_mul_1':
lib/mpi/generic_mpih-mul1.c:50:3: error: impossible constraint in 'asm'
This patch updates MPI with the latest umul_ppm implementations for MIPS.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Cc: James Morris <jmorris@namei.org>
Patchwork: https://patchwork.linux-mips.org/patch/4612/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
A recent patch changed some irq routines from inlines to functions.
These routines are called by the tracer code. Now that they're functions,
if they are compiled for function tracing they will call the tracer
and crash the system due to infinite recursion. The fix disables
tracing in these functions by using "notrace" in the function
definition.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: David Daney <david.daney@cavium.com>
Pathchwork: https://patchwork.linux-mips.org/patch/4564/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Without this, we may end up with something like this in /proc/iomem:
01100000-014fffff : System RAM
01100000-013bf48f : Kernel code
013bf490-0149e01f : Kernel data
01500000-0c0fffff : System RAM
but the two System RAM ranges should be one single range. This particular
case will result in kexec failure on Octeon systems if the kernel being
loaded by kexec is bigger than the already running kernel.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
After we've done __elv_add_request() and __blk_run_queue() in
blk_execute_rq_nowait(), the request might finish and be freed
immediately. Therefore checking if the type is REQ_TYPE_PM_RESUME
isn't safe afterwards, because if it isn't, rq might be gone.
Instead, check beforehand and stash the result in a temporary.
This fixes crashes in blk_execute_rq_nowait() I get occasionally when
running with lots of memory debugging options enabled -- I think this
race is usually harmless because the window for rq to be reallocated
is so small.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Hi Jens,
Another tiny patch.
Removed __packed before the struct smart_attr and added __packed at end of
the structure to fix padding issue.
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Calling the request handler directly on a plugged queue defeats
the performance improvements provided by the plugging mechanism.
Use the __blk_run_queue function instead of calling the request
handler directly, so that we don't interfere with the block
layer's ability to plug the queue.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The dereference to port should be moved below the NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If we're building a 32-bit kernel and CONFIG_LBADF isn't set,
sector_t is 32-bits wide. The shifts by 32 and 40 are thus
larger than we support.
Cast the sector offset to a u64 to avoid these warnings.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Previous commit use value 3 for erasemode mask.
Changing the mask to correct value to 2
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Earlier lba address was assigned directly to lba_low and lba_low_ex,
which would result in a different number (bytes reversed) in
big-endian systems. Now assigning lba address byte-by-byte to fis.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The mtip driver lifted this code from elsewhere and then added a special
handling check for SEC_ERASE_UNIT. If the caller tries to do a security
erase but passes no output data for the command then outbuf is not
allocated and the driver duly explodes.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Request based dm attempts to re-run the request queue off the
request completion path. If used with a driver that potentially does
end_io from its request_fn, we could deadlock trying to recurse
back into request dispatch. Fix this by punting the request queue
run to kblockd.
Tested to fix a quickly reproducible deadlock in such a scenario.
Cc: stable@kernel.org
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We need to first destroy the floppy_wq workqueue before cleaning up
the queue. Otherwise we might race with still pending work with the
workqueue, but all the block queue already gone. This might lead to
various oopses, such as
CPU 0
Pid: 6, comm: kworker/u:0 Not tainted 3.7.0-rc4 #1 Bochs Bochs
RIP: 0010:[<ffffffff8134eef5>] [<ffffffff8134eef5>] blk_peek_request+0xd5/0x1c0
RSP: 0000:ffff88000dc7dd88 EFLAGS: 00010092
RAX: 0000000000000001 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff88000f602688 RSI: ffffffff81fd95d8 RDI: 6b6b6b6b6b6b6b6b
RBP: ffff88000dc7dd98 R08: ffffffff81fd95c8 R09: 0000000000000000
R10: ffffffff81fd9480 R11: 0000000000000001 R12: 6b6b6b6b6b6b6b6b
R13: ffff88000dc7dfd8 R14: ffff88000dc7dfd8 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffffffff81e21000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 0000000001e11000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process kworker/u:0 (pid: 6, threadinfo ffff88000dc7c000, task ffff88000dc5ecc0)
Stack:
0000000000000000 0000000000000000 ffff88000dc7ddb8 ffffffff8134efee
ffff88000dc7ddb8 0000000000000000 ffff88000dc7dde8 ffffffff814aef3c
ffffffff81e75d80 ffff88000dc0c640 ffff88000fbfb000 ffffffff814aed90
Call Trace:
[<ffffffff8134efee>] blk_fetch_request+0xe/0x30
[<ffffffff814aef3c>] redo_fd_request+0x1ac/0x400
[<ffffffff814aed90>] ? start_motor+0x130/0x130
[<ffffffff8106b526>] process_one_work+0x136/0x450
[<ffffffff8106af65>] ? manage_workers+0x205/0x2e0
[<ffffffff8106bb6d>] worker_thread+0x14d/0x420
[<ffffffff8106ba20>] ? rescuer_thread+0x1a0/0x1a0
[<ffffffff8107075a>] kthread+0xba/0xc0
[<ffffffff810706a0>] ? __kthread_parkme+0x80/0x80
[<ffffffff818b553a>] ret_from_fork+0x7a/0xb0
[<ffffffff810706a0>] ? __kthread_parkme+0x80/0x80
Code: 0f 84 c0 00 00 00 83 f8 01 0f 85 e2 00 00 00 81 4b 40 00 00 80 00 48 89 df e8 58 f8 ff ff be fb ff ff ff
fe ff ff <49> 8b 1c 24 49 39 dc 0f 85 2e ff ff ff 41 0f b6 84 24 28 04 00
RIP [<ffffffff8134eef5>] blk_peek_request+0xd5/0x1c0
RSP <ffff88000dc7dd88>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"This fixes recent regression where /dev/input/mice got assigned wrong
device node which messed up setups with static /dev, and a regression
in ads7846 GPIO debounce setup."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
ARM - OMAP: ads7846: fix pendown debounce setting
Input: ads7846 - enable pendown GPIO debounce time setting
Input: mousedev - move /dev/input/mice to the correct minor
Input: MT - document new 'flags' argument of input_mt_init_slots()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim:
Here is Samsung fixes for v3.7 and it is for fixing of mdma1 address
for exynos4210 rev0 SoC.
* 'v3.7-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: PL330 MDMA1 fix for revision 0 of Exynos4210 SOC
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The new EEH code introduced a small regression, if the EEH PEs
are missin (which happens currently in qemu for example), it
will deref a NULL pointer in the MSI code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Properly terminate the DMA transfer in case the DMA PIO transfer
or setup fails for any reason.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|