summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2011-07-21netxen: add fw version compatibility checkAmit Kumar Salecha3-13/+68
o Minimum fw version supported for P3 chip is 4.0.505 o File Fw > 4.0.554 is not supported if flash fw < 4.0.554. o In mn firmware case, file fw older than flash fw is allowed. o Change variable names for readability o Update driver version 4.0.76 Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21be2net: request native mode each time the card is resetSathya Perla3-4/+6
Currently be3-native mode is requested only in probe(). It must be requested, each time the card is reset either after an EEH error or after sleep/hibernation. Also, the be_cmd_check_native_mode() is better named be_cmd_req_native_mode() Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21ipv4: Constrain UFO fragment sizes to multiples of 8 bytesBill Sommerfeld1-3/+3
Because the ip fragment offset field counts 8-byte chunks, ip fragments other than the last must contain a multiple of 8 bytes of payload. ip_ufo_append_data wasn't respecting this constraint and, depending on the MTU and ip option sizes, could create malformed non-final fragments. Google-Bug-Id: 5009328 Signed-off-by: Bill Sommerfeld <wsommerfeld@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21virtio_net: Fix panic in virtnet_removeKrishna Kumar1-9/+1
Fix a panic in virtnet_remove. unregister_netdev has already freed up the netdev (and virtnet_info) due to dev->destructor being set, while virtnet_info is still required. Remove virtnet_free altogether, and move the freeing of the per-cpu statistics from virtnet_free to virtnet_remove. Tested patch below. Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21ipv6: make fragment identifications less predictableEric Dumazet7-22/+64
IPv6 fragment identification generation is way beyond what we use for IPv4 : It uses a single generator. Its not scalable and allows DOS attacks. Now inetpeer is IPv6 aware, we can use it to provide a more secure and scalable frag ident generator (per destination, instead of system wide) This patch : 1) defines a new secure_ipv6_id() helper 2) extends inet_getid() to provide 32bit results 3) extends ipv6_select_ident() with a new dest parameter Reported-by: Fernando Gont <fernando@gont.com.ar> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21ipv6: unshare inetpeersEric Dumazet1-13/+20
We currently cow metrics a bit too soon in IPv6 case : All routes are tied to a single inetpeer entry. Change ip6_rt_copy() to get destination address as second argument, so that we fill rt6i_dst before the dst_copy_metrics() call. icmp6_dst_alloc() must set rt6i_dst before calling dst_metric_set(), or else the cow is done while rt6i_dst is still NULL. If orig route points to readonly metrics, we can share the pointer instead of performing the memory allocation and copy. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21can: make function can_get_bittiming staticThadeu Lima de Souza Cascardo1-1/+1
The function can_get_bittiming is not used anywhere else, so it should be static. Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21net: Kobj and queues_kset should be used when CONFIG_XPS is enabledChoi, Jong-Hwan1-2/+2
Kobj and queues_kset are used with CONFIG_XPS=y. Signed-off-by: Choi, Jong-Hwan <jhbird.choi@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21vmxnet3: fix publicity of NETIF_F_HIGHDMAShreyas Bhatewara1-1/+1
NETIF_F_HIGHDMA is being disabled even when dma64 is true. This patch fixes it. CC: Michal Miroslaw <mirq-linux@rere.qmqm.pl> Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21vmxnet3: set netdev parant device before calling netdev_infoShreyas Bhatewara1-1/+1
Parent device for netdev should be set before netdev_info() can be called otherwise there is a NULL pointer dereference and probe() fails. Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by: Scott J. Goldman <scottjg@vmware.com>-- Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21ASIX: Add AX88772B USB IDMarek Vasut1-0/+4
This device can be found in Acer Iconia TAB W500 tablet dock. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21Merge branch 'master' of ↵David S. Miller1-6/+14
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
2011-07-21stmmac: improve and up-to-date the documentationGiuseppe CAVALLARO1-64/+136
This patch adds new information for the driver especially about its platform structure fields. Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21stmmac: unify MAC and PHY configuration parameters (V2)Giuseppe CAVALLARO4-131/+77
Prior to this change, most PHY configuration parameters were passed into the STMMAC device as a separate PHY device. As well as being unusual, this made it difficult to make changes to the MAC/PHY relationship. This patch moves all the PHY parameters into the MAC configuration structure, mainly as a separate structure. This allows us to completely ignore the MDIO bus attached to a stmmac if desired, and not create the PHY bus. It also allows the stmmac driver to use a different PHY from the one it is connected to, for example a fixed PHY or bit banging PHY. Also derive the stmmac/PHY connection type (MII/RMII etc) from the mode can be passed into <platf>_configure_ethernet. STLinux kernel at git://git.stlinux.com/stm/linux-sh4-2.6.32.y.git provides several examples how to use this new infrastructure (that actually is easier to maintain and clearer). Signed-off-by: Stuart Menefy <stuart.menefy@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21stmmac: remove warning when compile as built-in (V2)Giuseppe CAVALLARO1-23/+42
The patch removes the following serie of warnings when the driver is compiled as built-in: drivers/net/stmmac/stmmac_main.c: In function stmmac_cmdline_opt: drivers/net/stmmac/stmmac_main.c:1855:12: warning: ignoring return value of kstrtoul, declared with attribute warn_unused_result [snip] Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21stmmac: update the version (V2)Giuseppe CAVALLARO1-1/+1
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21ethtool: Allow zero-length register dumps againBen Hutchings1-2/+2
Some drivers (ab)use the ethtool_ops::get_regs operation to expose only a hardware revision ID. Commit a77f5db361ed9953b5b749353ea2c7fed2bf8d93 ('ethtool: Allocate register dump buffer with vmalloc()') had the side-effect of breaking these, as vmalloc() returns a null pointer for size=0 whereas kmalloc() did not. For backward-compatibility, allow zero-length dumps again. Reported-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Cc: stable@kernel.org [2.6.37+] Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21jme: Fix unmap error (Causing system freeze)Guo-Fu Tseng1-6/+14
This patch add the missing dma_unmap(). Which solved the critical issue of system freeze on heavy load. Michal Miroslaw's rejected patch: [PATCH v2 10/46] net: jme: convert to generic DMA API Pointed out the issue also, thank you Michal. But the fix was incorrect. It would unmap needed address when low memory. Got lots of feedback from End user and Gentoo Bugzilla. https://bugs.gentoo.org/show_bug.cgi?id=373109 Thank you all. :) Cc: stable@kernel.org Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Acked-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21skbuff: fix error handling in pskb_copy()Dan Carpenter1-1/+2
There are two problems: 1) "n" was allocated with alloc_skb() so we should free it with kfree_skb() instead of regular kfree(). 2) We return the freed pointer instead of NULL. Signed-off-by: Dan Carpenter <error27@gmail.com> Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21vlan: move vlan_group_[gs]et_device to public headerJiri Pirko2-19/+19
there are no users outside vlan code Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21vlan: kill ndo_vlan_rx_registerJiri Pirko2-12/+0
has no users so remove it Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21macvlan: do vlan cleanupJiri Pirko1-12/+0
ndo_vlan_rx_register is no longer in use in any driver so remove it. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21bonding: do vlan cleanupJiri Pirko4-83/+33
Now when all devices are cleaned up, bond can be cleaned up as well - remove bond->vlgrp - remove bond_vlan_rx_register - substitute necessary occurences of vlan_group_get_device Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21staging: et131x: remove unused prototype et131x_vlan_rx_registerJiri Pirko1-1/+0
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21qlcnic: remove usage of vlan_group_get_deviceJiri Pirko1-6/+1
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21stmmac: do vlan cleanupJiri Pirko2-20/+0
- kill priv->vlgrp and stmmac_vlan_rx_register (used for nothing :)) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21vlan: kill vlan_gro_frags and vlan_gro_receiveJiri Pirko2-36/+0
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21qeth: do vlan cleanupJiri Pirko3-56/+47
- unify vlan and nonvlan rx path - kill card->vlangrp and qeth_l3_vlan_rx_register Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21vxge: do vlan cleanupJiri Pirko2-80/+16
- unify vlan and nonvlan rx path - kill vdev->vlgrp and vxge_vlan_rx_register Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21igb: do vlan cleanupJiri Pirko2-47/+47
- unify vlan and nonvlan rx path - kill adapter->vlgrp and igb_vlan_rx_register - allow to turn on/off rx/tx vlan accel via ethtool (set_features) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21forcedeth: do vlan cleanupJiri Pirko1-38/+30
- unify vlan and nonvlan rx path - kill np->vlangrp and nv_vlan_rx_register - allow to turn on/off rx vlan accel via ethtool (set_features) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21e1000: do vlan cleanupJiri Pirko2-62/+108
- unify vlan and nonvlan rx path - kill adapter->vlgrp and e1000_vlan_rx_register - allow to turn on/off rx/tx vlan accel via ethtool (set_features) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21vlan: kill __vlan_hwaccel_rx and vlan_hwaccel_rxJiri Pirko2-31/+0
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21cxgb3: do vlan cleanupJiri Pirko4-48/+49
- unify vlan and nonvlan rx path - kill pi->vlan_grp and vlan_rx_register - allow to turn on/off rx/tx vlan accel via ethtool (set_features) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21atl2: do vlan cleanupJiri Pirko2-33/+48
- unify vlan and nonvlan rx path - kill adapter->vlgrp and atl2_vlan_rx_register - allow to turn on/off rx/tx vlan accel via ethtool (set_features) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21atl1: do vlan cleanupJiri Pirko3-28/+51
- unify vlan and nonvlan rx path - kill adapter->vlgrp and atlx_vlan_rx_register - allow to turn on/off rx/tx vlan accel via ethtool (set_features) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21ns83820: do vlan cleanupJiri Pirko1-29/+4
- unify vlan and nonvlan rx path - kill dev->vlgrp and ns83820_vlan_rx_register Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21starfire: do vlan cleanupJiri Pirko1-50/+39
- unify vlan and nonvlan rx path - kill np->vlgrp and netdev_vlan_rx_register Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21via-velocity: do vlan cleanupJiri Pirko2-30/+21
- unify vlan and nonvlan rx path - kill vptr->vlgrp and velocity_vlan_rx_register Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21acenic: do vlan cleanupJiri Pirko2-60/+7
- unify vlan and nonvlan rx path - kill ap->vlgrp and ace_vlan_rx_register - enable vlan hw accel always (kill vlan ifdefs) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21ixgbevf: do vlan cleanupJiri Pirko2-52/+18
- unify vlan and nonvlan rx path - kill adapter->vlgrp and ixgbevf_vlan_rx_register Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21vlan: kill vlan_hwaccel_receive_skbJiri Pirko1-13/+0
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21tehuti: do vlan cleanupJiri Pirko2-31/+7
- unify vlan and nonvlan rx path - kill priv->vlgrp and bdx_vlan_rx_register Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21spider_net: do not mention dying vlan_hwaccel_receive_skbJiri Pirko1-3/+1
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21s2io: do vlan cleanupJiri Pirko2-65/+6
- unify vlan and nonvlan rx path - kill sp->vlgrp and s2io_vlan_rx_register and s2io_vlan_rx_kill_vid (which does nothing and is never called :)) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21qlge: do vlan cleanupJiri Pirko2-71/+93
- unify vlan and nonvlan path - kill qdev->vlgrp and qlge_vlan_rx_register - allow to turn on/off rx/tx vlan accel via ethtool (set_features) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21mlx4: do vlan cleanupJiri Pirko4-65/+37
- unify vlan and nonvlan path - kill priv->vlgrp and mlx4_en_vlan_rx_register Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21jme: do vlan cleanupJiri Pirko2-27/+5
- unify vlan and nonvlan rx path - kill jme->vlgrp and jme_vlan_rx_register Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21igbvf: do vlan cleanupJiri Pirko2-32/+16
- unify vlan and nonvlan rx path - kill adapter->vlgrp and igbvf_vlan_rx_register Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21gianfar: do vlan cleanupJiri Pirko3-28/+33
- unify vlan and nonvlan rx path - kill priv->vlgrp and gfar_vlan_rx_register - allow to turn on/off rx/tx vlan accel via ethtool Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-10-16 21:38:54 +0000