| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt64
Pull "arm64: tegra: Device tree changes for v4.9-rc1" from Thierry Reding:
Add a couple of devices (AGIC, ADMA) on Tegra210 and enable them on
Smaug. Also enable DPAUX on Smaug to allow the I2C bus that shares pads
with the DPAUX to be used to access various audio devices. Furthermore,
enable the XUSB controller on Smaug for USB 3.0 support.
Finally, select PM_GENERIC_DOMAINS for 64-bit Tegra devices to make sure
devices are probed only after their power partitions have been enabled.
* tag 'tegra-for-4.9-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Select PM_GENERIC_DOMAINS
arm64: tegra: Enable XUSB controller on Tegra210 Smaug
arm64: tegra: Add the various audio devices for Tegra210 Smaug
arm64: tegra: Enable DPAUX for Tegra210 Smaug
arm64: tegra: Add ACONNECT, ADMA and AGIC nodes Tegra210 Smaug
arm64: tegra: Add SOR power-domain for Tegra210
arm64: tegra: Add ADMA node for Tegra210
arm64: tegra: Add AGIC node for Tegra210
arm64: tegra: Drop clock and reset names for XUSB powergates
arm64: tegra: Simplify Tegra210 GPIO compatible value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
Pull "Rockchip dts64 changes for 4.9" from Heiko Stübner:
64bit Rockchip devicetree changes containing support for the recently
added firmware reboot-flag support, one new board the Tronsmart Orion
based on the rk3368 and a large number of newly supported peripherals
for the rk3399 (type-c phy, usb2 phy, pcie controller and pcie phy,
gmac, arm-pmu using ppi partitioning, efuse, saradc) as well as some
smaller housekeeping and non-critical fixes.
* tag 'v4.9-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (22 commits)
arm64: dts: rockchip: add Type-C phy for RK3399
arm64: dts: rockchip: enable the gmac for rk3399 evb board
arm64: dts: rockchip: add the gmac needed node for rk3399
arm64: dts: rockchip: support the pmu node for rk3399
arm64: dts: rockchip: change all interrupts cells to 4 on rk3399 SoCs
arm64: dts: rockchip: add the tcpc for rk3399 power domain
arm64: dts: rockchip: add efuse0 device node for rk3399
arm64: dts: rockchip: configure PCIe support for rk3399-evb
arm64: dts: rockchip: add the PCIe controller support for RK3399
arm64: dts: rockchip: add the PCIe PHY for RK3399
arm64: dts: rockchip: add the gmac power domain on rk3399
arm64: dts: rockchip: Add pinctrl entry for 32k clock on rk3399
arm64: dts: rockchip: set to CCI clock of RK3399 to 600M
arm64: dts: rockchip: fix the address map for WDT0 and WDT1
arm64: dts: rockchip: add the saradc for rk3399
arm64: dts: rockchip: configure usb2-phy support for rk3399-evb
arm64: dts: rockchip: add usb2-phy support for rk3399
arm64: dts: rockchip: add syscon-reboot-mode DT node
soc: rockchip: add reboot-mode header
arm64: dts: rockchip: remove broken-cd from sdio0
...
|
|
http://github.com/Broadcom/stblinux into next/dt64
Pull "Broadcom devicetree-arm64 changes for 4.9" from Florian Fainelli:
This pull request contains Broadcom ARM64-based SoC Device Tree changes for
v4.9, please pull the folllowing:
- Dhanajay adds the PWM Device Tree nodes to the Northstar 2 DTS files
* tag 'arm-soc/for-4.9/devicetree-arm64' of http://github.com/Broadcom/stblinux:
arm64: dts: Add PWM DT node for NS2
|
|
next/dt64
Pull "mvebu dt64 for 4.9 (part 1)" from Gregory CLEMENT:
- add description for the new Armada 8040 dev board
- add the PIC and PMU on Armada 7K/8K
* tag 'mvebu-dt64-4.9-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: describe the PIC and PMU on Armada 7K/8K
arm64: dts: marvell: add description for the Armada 8040 dev board
arm64: dts: marvell: add description for the slave CP110 in Armada 8K
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt64
Pull "Qualcomm ARM64 Updates for v4.9" from Andy Gross:
* Updates for MSM8916 including TSCR, SMSM/SMP2P, and MBA reserve
* Update SCM node to denote being a reset-controller
* Fix broken interrupt settings
* Add TSENS nodes for MSM8916/MSM8996
* Add DB820c support
* Add MSM8916/APQ8016 display support
* tag 'qcom-arm64-for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: apq8016-sbc: Add HDMI display support
arm64: dts: msm8916: Add display support
arm64: dts: db820c: add support to external sd card.
arm64: dts: db820c: add support to SPI on HS
arm64: dts: db820c: add support to LS-SPI0
arm64: dts: db820c: add support to I2C on HS
arm64: dts: db820c: add support to LS-I2C1
arm64: dts: db820c: add support to LS-I2C0
arm64: dts: db820c: add support to LS-UART0
arm64: dts: db820c: add basic board support
arm64: dts: msm8996: Add thermal zones, tsens and qfprom nodes
arm64: dts: msm8916: Add thermal zones, tsens and qfprom nodes
arm64: dts: qcom: Fix broken interrupt trigger settings
arm64: dts: qcom: msm8916: Add tcsr syscon
arm64: dts: qcom: msm8916: Make scm a reset-controller
arm64: dts: qcom: msm8916: Add mba memory reserve
arm64: dts: qcom: msm8916: Add smsm and smp2p nodes
|
|
into next/dt64
Pull "ARM64: DT: Hisilicon SoC DT updates for 4.9" from Wei Xu:
- Set UART1 clock frequency to 150MHz for higher baud rates on hikey
- Add display subsystem, HDMI and cma nodes on hikey to support display
- Add syscon-reboot-mode support on hikey
- Add pstore support on hikey
- Add resets and sd-uhs-sdr property dwmmc ndoe on hikey
- Remove hip05_hns.dtsi since it can not be built without mbigenv1
- Update system controller bingding document for hip05 and hip06
- Add xge and sas support on hip06
* tag 'hisi-soc-dt-for-4.9' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hi6220: add sd-uhs- properties into dwmmc_1
arm64: dts: hi6220: add resets property into dwmmc nodes
arm64: dts: hikey: extend default cma size to 128MB
arm64: dts: hip06: Append sas node
arm64: dts: hip06: Append hns node
dt-bindings: hisilicon: Add Hip05 and Hip06 system controller support
arm64: dts: hip05: kill hip05_hns.dtsi
arm64: dts: hikey: Add pstore support for HiKey
arm64: dts: hikey: Add hikey support for syscon-reboot-mode
arm64: dts: Add HDMI node for hi6220-hikey
arm64: dts: Add display subsystem DT nodes for hi6220-hikey
arm64: dts: set UART1 clock frequency to 150MHz
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Pull "Samsung DeviceTree ARM64 update for v4.9" from Krzysztof Kozlowski:
1. Use human-friendly symbols for interrupt flags.
* tag 'samsung-dt64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Use human-friendly symbols for timer interrupt flags
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt64
Merge "UniPhier ARM64 SoC DT updates for v4.9" from Masahiro Yamada:
* Match DT names other projects and documents
* Use clock/reset drivers
* Add new SoC/board support
* Misc
* tag 'uniphier-dt64-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: add LD11 SoC/Board support
arm64: dts: uniphier: add specific compatible to SoC-Glue node
arm64: dts: uniphier: use clock/reset controllers
arm64: dts: uniphier: add pinctrl property to System Bus node
arm64: dts: uniphier: match DT names to other projects and documents
|
|
There are 2 Type-C phy on RK3399, they are almost same, except the
address of register. They support USB3.0 Type-C and DisplayPort1.3
Alt Mode on USB Type-C. Register a phy, supply it to USB3 controller
and DP controller.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
We add the required and optional properties for evb board.
See the [0] to get the detail information.
[0]:
Documentation/devicetree/bindings/net/rockchip-dwmac.txt
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The RK3399 GMAC Ethernet Controller provides a complete Ethernet interface
from processor to a Reduced Media Independent Interface (RMII) and Reduced
Gigabit Media Independent Interface (RGMII) compliant Ethernet PHY.
This patch adds the related needed device information.
e.g.: interrupts, grf, clocks, pinctrl and so on.
The full details are in [0].
[0]:
Documentation/devicetree/bindings/net/rockchip-dwmac.txt
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds to enable the ARM Performance Monitor Units for rk3399.
ARM cores often have a PMU for counting cpu and cache events like cache
misses and hits.
This uses the new interrupt-partition mechanism to allow the two pmu
instances to use the per-cpu interrupt.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the interrupts cells value for 4, and the 4th cell is zero.
Due to the doc[0] said:" the system requires describing PPI affinity,
then the value must be at least 4"
The 4th cell is a phandle to a node describing a set of CPUs this
interrupt is affine to. The interrupt must be a PPI, and the node
pointed must be a subnode of the "ppi-partitions" subnode. For
interrupt types other than PPI or PPIs that are not partitionned,
this cell must be zero. See the "ppi-partitions" node description
below.
[0]:
Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The tcpc is the Type C Port Controller and Type C Port Delivery (tcpd)
is part of it, we haven't used them now, add it to save power consumption.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add a efuse0 node in the device tree for the ARM64 rk3399 SoC.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Let's assigne slot numbers, ep-gpios and clkreq used by PCIe
on evb board as well the PHY node here. Note that we still
disable them as the auto training of PCIe link will make the
kernel use more time to boot if there are no any devices there.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch introduces PCIe support found on RK3399 platform,
and specify phys phandle for it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds PCIe node for RK3399 to support
PCIe controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds the gmac ppower-domain to save power consumption
by letting the driver core handle the power-domain so we can
save power on boards not needing Ethernet.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
On some rk3399 boards GPIO0_A0 is hooked up to a 32 kHz clock. This can
be used as the source for various clocks in the system.
Add a pinmux so boards can get this pin properly configured.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
With these properties added, sd cards inserted into hikey can work at UHS
mode if they have such capability.
Note, this depends on HiKey UHS-SD support patch [1] to work properly.
If you didn't add this patch, but added sd-uhs- properties into dwmmc_1,
then sd cards cannot work. As of this post, patch [1] has been integrated
into maintainer's next branch [2].
[1]: [V4] mmc: dw_mmc-k3: UHS-SD card for Hisilicon Hikey,
https://patchwork.kernel.org/patch/9262515/
[2]: https://git.linaro.org/people/ulf.hansson/mmc.git next
commit a8a5b2909cfc ("mmc: dw_mmc: k3: UHS-SD card for Hisilicon Hikey")
cc: Ulf Hansson <ulf.hansson@linaro.org>
cc: Jaehoon Chung <jh80.chung@samsung.com>
cc: Jinguojun <kid.jin@hisilicon.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
This is a low-cost 64bit SoC from Socionext.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This is a simple MFD, but add a specific compatible just in case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The UniPhier reset controller driver has been merged. Enable it.
Also, replace the fixed-rate clocks with the dedicated clock
drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add resets property into dwmmc_0, dwmmc_1 and dwmmc_2 for hi6220
Code and documentation to this property were confirmed by maintainers.
See:
[1] https://patchwork.kernel.org/patch/9276607/
[2] https://patchwork.kernel.org/patch/8487151/
[3] https://lkml.org/lkml/2016/8/12/91
cc: Jaehoon Chung <jh80.chung@samsung.com>
cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
To support display in Debian on HiKey, cma heap is used to allocate
graphic buffers. The default size of CMA is 16 MB which is not enough.
Increase the default CMA size to 128 MB.
cc: Fathi Boudra <fathi.boudra@linaro.org>
cc: John Stultz <john.stultz@linaro.org>
cc: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
This pinctrl is needed to get access to the UniPhier System Bus.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
All UniPhier device trees have the common prefix "uniphier-", so
"ph1-" is just making names longer. Recent documents and other
projects are not using PH1- prefixes any more.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
|
|
Pull drm fixes from Dave Airlie:
"A bunch of fixes covering i915, amdgpu, one tegra and some core DRM
ones. Nothing too strange at this point"
* tag 'drm-fixes-for-4.8-rc4' of git://people.freedesktop.org/~airlied/linux: (21 commits)
drm/atomic: Don't potentially reset color_mgmt_changed on successive property updates.
drm: Protect fb_defio in drivers with CONFIG_KMS_FBDEV_EMULATION
drm/amdgpu: skip TV/CV in display parsing
drm/amdgpu: avoid a possible array overflow
drm/amdgpu: fix lru size grouping v2
drm/tegra: dsi: Enhance runtime power management
drm/i915: Fix botched merge that downgrades CSR versions.
drm/i915/skl: Ensure pipes with changed wms get added to the state
drm/i915/gen9: Only copy WM results for changed pipes to skl_hw
drm/i915/skl: Add support for the SAGV, fix underrun hangs
drm/i915/gen6+: Interpret mailbox error flags
drm/i915: Reattach comment, complete type specification
drm/i915: Unconditionally flush any chipset buffers before execbuf
drm/i915/gen9: Drop invalid WARN() during data rate calculation
drm/i915/gen9: Initialize intel_state->active_crtcs during WM sanitization (v2)
drm: Reject page_flip for !DRIVER_MODESET
drm/amdgpu: fix timeout value check in amd_sched_job_recovery
drm/amdgpu: fix sdma_v2_4_ring_test_ib
drm/amdgpu: fix amdgpu_move_blit on 32bit systems
drm/radeon: fix radeon_move_blit on 32bit systems
...
|
|
property updates.
Due to assigning the 'replaced' value instead of or'ing it,
if drm_atomic_crtc_set_property() gets called multiple times,
the last call will define the color_mgmt_changed flag, so
a non-updating call to a property can reset the flag and
prevent actual hw state updates required by preceding
property updates.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: <stable@vger.kernel.org> # v4.6+
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A few fixes from the perf departement
- prevent a imbalanced preemption disable in the events teardown code
- prevent out of bound acces in perf userspace
- make perf tools compile with UCLIBC again
- a fix for the userspace unwinder utility"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Use this_cpu_ptr() when stopping AUX events
perf evsel: Do not access outside hw cache name arrays
tools lib: Reinstate strlcpy() header guard with __UCLIBC__
perf unwind: Use addr_location::addr instead of ip for entries
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"A single bugfix to prevent irq remapping when the ioapic is disabled"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Do not init irq remapping if ioapic is disabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"This lot provides:
- plug a hotplug race in the new affinity infrastructure
- a fix for the trigger type of chained interrupts
- plug a potential memory leak in the core code
- a few fixes for ARM and MIPS GICs"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mips-gic: Implement activate op for device domain
irqchip/mips-gic: Cleanup chip and handler setup
genirq/affinity: Use get/put_online_cpus around cpumask operations
genirq: Fix potential memleak when failing to get irq pm
irqchip/gicv3-its: Disable the ITS before initializing it
irqchip/gicv3: Remove disabling redistributor and group1 non-secure interrupts
irqchip/gic: Allow self-SGIs for SMP on UP configurations
genirq: Correctly configure the trigger on chained interrupts
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A few updates for timers & co:
- prevent a livelock in the timekeeping code when debugging is
enabled
- prevent out of bounds access in the timekeeping debug code
- various fixes in clocksource drivers
- a new maintainers entry"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/sun4i: Clear interrupts after stopping timer in probe function
drivers/clocksource/pistachio: Fix memory corruption in init
clocksource/drivers/timer-atmel-pit: Enable mck clock
clocksource/drivers/pxa: Fix include files for compilation
MAINTAINERS: Add ARM ARCHITECTED TIMER entry
timekeeping: Cap array access in timekeeping_debug
timekeeping: Avoid taking lock in NMI path with CONFIG_DEBUG_TIMEKEEPING
|
|
Pull KVM fixes from Paolo Bonzini:
"ARM:
- fixes for ITS init issues, error handling, IRQ leakage, race
conditions
- an erratum workaround for timers
- some removal of misleading use of errors and comments
- a fix for GICv3 on 32-bit guests
MIPS:
- fix for where the guest could wrongly map the first page of
physical memory
x86:
- nested virtualization fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
MIPS: KVM: Check for pfn noslot case
kvm: nVMX: fix nested tsc scaling
KVM: nVMX: postpone VMCS changes on MSR_IA32_APICBASE write
KVM: nVMX: fix msr bitmaps to prevent L2 from accessing L0 x2APIC
arm64: KVM: report configured SRE value to 32-bit world
arm64: KVM: remove misleading comment on pmu status
KVM: arm/arm64: timer: Workaround misconfigured timer interrupt
arm64: Document workaround for Cortex-A72 erratum #853709
KVM: arm/arm64: Change misleading use of is_error_pfn
KVM: arm64: ITS: avoid re-mapping LPIs
KVM: arm64: check for ITS device on MSI injection
KVM: arm64: ITS: move ITS registration into first VCPU run
KVM: arm64: vgic-its: Make updates to propbaser/pendbaser atomic
KVM: arm64: vgic-its: Plug race in vgic_put_irq
KVM: arm64: vgic-its: Handle errors from vgic_add_lpi
KVM: arm64: ITS: return 1 on successful MSI injection
|
|
Merge fixes from Andrew Morton:
"11 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: silently skip readahead for DAX inodes
dax: fix device-dax region base
fs/seq_file: fix out-of-bounds read
mm: memcontrol: avoid unused function warning
mm: clarify COMPACTION Kconfig text
treewide: replace config_enabled() with IS_ENABLED() (2nd round)
printk: fix parsing of "brl=" option
soft_dirty: fix soft_dirty during THP split
sysctl: handle error writing UINT_MAX to u32 fields
get_maintainer: quiet noisy implicit -f vcs_file_exists checking
byteswap: don't use __builtin_bswap*() with sparse
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull ARM64 fix from Catalin Marinas:
"ARM64 fix to avoid potential TLB conflict when CONFIG_RANDOMIZE_BASE
is enabled"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: avoid TLB conflict with CONFIG_RANDOMIZE_BASE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Round one of 4.8 rc fixes.
This should be the bulk of the -rc fixes for 4.8. I only have a few
things that are still outstanding (two ipoib bugs for which the
solution is not yet fully known, and a few queued items that came in
after my last push and I didn't want to delay this pull request for
late comers again).
Even though the patch count is kind of high, everything is minor fixes
so the overall churn is pretty low.
Summary:
- minor fixes to cxgb4
- minor fixes to mlx4
- one minor fix each to core, rxe, isert, srpt, mlx5, ocrdma, and usnic
- six or so fixes to i40iw fixes
- the rest are hfi1 fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (34 commits)
i40iw: Send last streaming mode message for loopback connections
IB/srpt: Update sport->port_guid with each port refresh
RDMA/ocrdma: Fix the max_sge reported from FW
i40iw: Avoid writing to freed memory
i40iw: Fix double free of allocated_buffer
IB/mlx5: Remove superfluous include of io-mapping.h
i40iw: Do not set self-referencing pointer to NULL after kfree
i40iw: Add missing NULL check for MPA private data
iw_cxgb4: Fix cxgb4 arm CQ logic w/IB_CQ_REPORT_MISSED_EVENTS
i40iw: Add missing check for interface already open
i40iw: Protect req_resource_num update
i40iw: Change mem_resources pointer to a u8
IB/core: Use memdup_user() rather than duplicating its implementation
IB/qib: Use memdup_user() rather than duplicating its implementation
iw_cxgb4: use the MPA initiator's IRD if < our ORD
iw_cxgb4: limit IRD/ORD advertised to ULP by device max.
IB/hfi1: Fix mm_struct use after free
IB/rdmvat: Fix double vfree() in rvt_create_qp() error path
IB/hfi1: Improve J_KEY generation
IB/hfi1: Return invalid field for non-QSFP CableInfo queries
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a bunch of fixes as you can see in diffstat.
One core change in ASoC is about the unexpected unbinding error, and
another about debugfs cleanup.
The rest are wide-spread driver-specific fixes: a series of LINE6 USB
fixes, a HD-audio quirk, and various ASoC fixes including OMAP boot
fixes and Intel SKL fixes"
* tag 'sound-4.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (22 commits)
ALSA: hda/realtek - fix headset mic detection for MSI MS-B120
ASoC: omap-mcpdm: Fix irq resource handling
ASoC: max98371: Add terminate entry for i2c_device_id tables
ALSA: line6: Fix POD sysfs attributes segfault
ALSA: line6: Give up on the lock while URBs are released.
ALSA: line6: Remove double line6_pcm_release() after failed acquire.
ASoC: omap-abe-twl6040: Correct dmic-codec device registration
ASoC: core: Clean up DAPM before the card debugfs
ASoC: omap-mcpdm: Drop pdmclk clock handling
ASoC: atmel_ssc_dai: Don't unconditionally reset SSC on stream startup
ASoC: compress: Fix leak of a widget list in soc_compr_open_fe
ASoC: Intel: Skylake: Fix error return code in skl_probe()
ASoC: wm2000: Fix return of uninitialised varible
ASoC: Fix leak of rtd in soc_bind_dai_link
ASoC: da7213: Default to 64 BCLKs per WCLK to support all formats
ASoC: nau8825: fix static check error about semaphone control
ASoC: nau8825: fix bug in playback when suspend
ASoC: samsung: Fix clock handling in S3C24XX_UDA134X card
ASoC: simple-card-utils: add missing MODULE_xxx()
ASoC: Intel: Skylake: Check list empty while getting module info
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"We've queued up a few different fixes in here. These range from
enospc corners to fsync and quota fixes, and a few targeted at error
handling for corrupt metadata/fuzzing"
* 'for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix lockdep warning on deadlock against an inode's log mutex
Btrfs: detect corruption when non-root leaf has zero item
Btrfs: check btree node's nritems
btrfs: don't create or leak aliased root while cleaning up orphans
Btrfs: fix em leak in find_first_block_group
btrfs: do not background blkdev_put()
Btrfs: clarify do_chunk_alloc()'s return value
btrfs: fix fsfreeze hang caused by delayed iputs deal
btrfs: update btrfs_space_info's bytes_may_use timely
btrfs: divide btrfs_update_reserved_bytes() into two functions
btrfs: use correct offset for reloc_inode in prealloc_file_extent_cluster()
btrfs: qgroup: Fix qgroup incorrectness caused by log replay
btrfs: relocation: Fix leaking qgroups numbers on data extents
btrfs: qgroup: Refactor btrfs_qgroup_insert_dirty_extent()
btrfs: waiting on qgroup rescan should not always be interruptible
btrfs: properly track when rescan worker is running
btrfs: flush_space: treat return value of do_chunk_alloc properly
Btrfs: add ASSERT for block group's memory leak
btrfs: backref: Fix soft lockup in __merge_refs function
Btrfs: fix memory leak of reloc_root
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm
Pull dlm fix from David Teigland:
"This fixes a bug introduced by recent debugfs cleanup"
* tag 'dlm-4.8-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
dlm: fix malfunction of dlm_tool caused by debugfs changes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- another stable fix for DM flakey (that tweaks the previous fix that
didn't factor in expected 'drop_writes' behavior for read IO).
- a dm-log bio operation flags fix for the broader block changes that
were merged during the 4.8 merge window.
* tag 'dm-4.8-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm log: fix unitialized bio operation flags
dm flakey: fix reads to be issued if drop_writes configured
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Fixes from Will Deacon:
- fix a couple of thinkos in the CMDQ error handling and
short-descriptor page table code that have been there since day one
- disable stalling faults, since they may result in hardware deadlock
- fix an accidental BUG() when passing disable_bypass=1 on the
cmdline"
* tag 'iommu-fixes-v4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/arm-smmu: Don't BUG() if we find aborting STEs with disable_bypass
iommu/arm-smmu: Disable stalling faults for all endpoints
iommu/arm-smmu: Fix CMDQ error handling
iommu/io-pgtable-arm-v7s: Fix attributes when splitting blocks
|
|
Pull block fixes from Jens Axboe:
"Here's a set of block fixes for the current 4.8-rc release. This
contains:
- a fix for a secure erase regression, from Adrian.
- a fix for an mmc use-after-free bug regression, also from Adrian.
- potential zero pointer deference in bdev freezing, from Andrey.
- a race fix for blk_set_queue_dying() from Bart.
- a set of xen blkfront fixes from Bob Liu.
- three small fixes for bcache, from Eric and Kent.
- a fix for a potential invalid NVMe state transition, from Gabriel.
- blk-mq CPU offline fix, preventing us from issuing and completing a
request on the wrong queue. From me.
- revert two previous floppy changes, since they caused a user
visibile regression. A better fix is in the works.
- ensure that we don't send down bios that have more than 256
elements in them. Fixes a crash with bcache, for example. From
Ming.
- a fix for deferencing an error pointer with cgroup writeback.
Fixes a regression. From Vegard"
* 'for-linus' of git://git.kernel.dk/linux-block:
mmc: fix use-after-free of struct request
Revert "floppy: refactor open() flags handling"
Revert "floppy: fix open(O_ACCMODE) for ioctl-only open"
fs/block_dev: fix potential NULL ptr deref in freeze_bdev()
blk-mq: improve warning for running a queue on the wrong CPU
blk-mq: don't overwrite rq->mq_ctx
block: make sure a big bio is split into at most 256 bvecs
nvme: Fix nvme_get/set_features() with a NULL result pointer
bdev: fix NULL pointer dereference
xen-blkfront: free resources if xlvbd_alloc_gendisk fails
xen-blkfront: introduce blkif_set_queue_limits()
xen-blkfront: fix places not updated after introducing 64KB page granularity
bcache: pr_err: more meaningful error message when nr_stripes is invalid
bcache: RESERVE_PRIO is too small by one when prio_buckets() is a power of two.
bcache: register_bcache(): call blkdev_put() when cache_alloc() fails
block: Fix race triggered by blk_set_queue_dying()
block: Fix secure erase
nvme: Prevent controller state invalid transition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov:
"Simply small driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ads7846 - remove redundant regulator_disable call
Input: synaptics-rmi4 - fix register descriptor subpacket map construction
Input: tegra-kbc - fix inverted reset logic
Input: silead - use devm_gpiod_get
Input: i8042 - set up shared ps2_cmd_mutex for AUX ports
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Resource management:
- Update "pci=resource_alignment" documentation (Mathias Koehrer)
MSI:
- Use positive flags in pci_alloc_irq_vectors() (Christoph Hellwig)
- Call pci_intx() when using legacy interrupts in pci_alloc_irq_vectors() (Christoph Hellwig)
Intel VMD host bridge driver:
- Fix infinite loop executing irq's (Keith Busch)"
* tag 'pci-v4.8-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
x86/PCI: VMD: Fix infinite loop executing irq's
PCI: Call pci_intx() when using legacy interrupts in pci_alloc_irq_vectors()
PCI: Use positive flags in pci_alloc_irq_vectors()
PCI: Update "pci=resource_alignment" documentation
|
|
For DAX inodes we need to be careful to never have page cache pages in
the mapping->page_tree. This radix tree should be composed only of DAX
exceptional entries and zero pages.
ltp's readahead02 test was triggering a warning because we were trying
to insert a DAX exceptional entry but found that a page cache page had
already been inserted into the tree. This page was being inserted into
the radix tree in response to a readahead(2) call.
Readahead doesn't make sense for DAX inodes, but we don't want it to
report a failure either. Instead, we just return success and don't do
any work.
Link: http://lkml.kernel.org/r/20160824221429.21158-1-ross.zwisler@linux.intel.com
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Jan Kara <jack@suse.com>
Cc: <stable@vger.kernel.org> [4.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The data offset for a dax region needs to account for a reservation in
the resource range. Otherwise, device-dax is allowing mappings directly
into the memmap or device-info-block area with crash signatures like the
following:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: get_zone_device_page+0x11/0x30
Call Trace:
follow_devmap_pmd+0x298/0x2c0
follow_page_mask+0x275/0x530
__get_user_pages+0xe3/0x750
__gfn_to_pfn_memslot+0x1b2/0x450 [kvm]
tdp_page_fault+0x130/0x280 [kvm]
kvm_mmu_page_fault+0x5f/0xf0 [kvm]
handle_ept_violation+0x94/0x180 [kvm_intel]
vmx_handle_exit+0x1d3/0x1440 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0x81d/0x16a0 [kvm]
kvm_vcpu_ioctl+0x33c/0x620 [kvm]
do_vfs_ioctl+0xa2/0x5d0
SyS_ioctl+0x79/0x90
entry_SYSCALL_64_fastpath+0x1a/0xa4
Fixes: ab68f2622136 ("/dev/dax, pmem: direct access to persistent memory")
Link: http://lkml.kernel.org/r/147205536732.1606.8994275381938837346.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Abhilash Kumar Mulumudi <m.abhilash-kumar@hpe.com>
Reported-by: Toshi Kani <toshi.kani@hpe.com>
Tested-by: Toshi Kani <toshi.kani@hpe.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
seq_read() is a nasty piece of work, not to mention buggy.
It has (I think) an old bug which allows unprivileged userspace to read
beyond the end of m->buf.
I was getting these:
BUG: KASAN: slab-out-of-bounds in seq_read+0xcd2/0x1480 at addr ffff880116889880
Read of size 2713 by task trinity-c2/1329
CPU: 2 PID: 1329 Comm: trinity-c2 Not tainted 4.8.0-rc1+ #96
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
Call Trace:
kasan_object_err+0x1c/0x80
kasan_report_error+0x2cb/0x7e0
kasan_report+0x4e/0x80
check_memory_region+0x13e/0x1a0
kasan_check_read+0x11/0x20
seq_read+0xcd2/0x1480
proc_reg_read+0x10b/0x260
do_loop_readv_writev.part.5+0x140/0x2c0
do_readv_writev+0x589/0x860
vfs_readv+0x7b/0xd0
do_readv+0xd8/0x2c0
SyS_readv+0xb/0x10
do_syscall_64+0x1b3/0x4b0
entry_SYSCALL64_slow_path+0x25/0x25
Object at ffff880116889100, in cache kmalloc-4096 size: 4096
Allocated:
PID = 1329
save_stack_trace+0x26/0x80
save_stack+0x46/0xd0
kasan_kmalloc+0xad/0xe0
__kmalloc+0x1aa/0x4a0
seq_buf_alloc+0x35/0x40
seq_read+0x7d8/0x1480
proc_reg_read+0x10b/0x260
do_loop_readv_writev.part.5+0x140/0x2c0
do_readv_writev+0x589/0x860
vfs_readv+0x7b/0xd0
do_readv+0xd8/0x2c0
SyS_readv+0xb/0x10
do_syscall_64+0x1b3/0x4b0
return_from_SYSCALL_64+0x0/0x6a
Freed:
PID = 0
(stack is not available)
Memory state around the buggy address:
ffff88011688a000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff88011688a080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff88011688a100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff88011688a180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88011688a200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Disabling lock debugging due to kernel taint
This seems to be the same thing that Dave Jones was seeing here:
https://lkml.org/lkml/2016/8/12/334
There are multiple issues here:
1) If we enter the function with a non-empty buffer, there is an attempt
to flush it. But it was not clearing m->from after doing so, which
means that if we try to do this flush twice in a row without any call
to traverse() in between, we are going to be reading from the wrong
place -- the splat above, fixed by this patch.
2) If there's a short write to userspace because of page faults, the
buffer may already contain multiple lines (i.e. pos has advanced by
more than 1), but we don't save the progress that was made so the
next call will output what we've already returned previously. Since
that is a much less serious issue (and I have a headache after
staring at seq_read() for the past 8 hours), I'll leave that for now.
Link: http://lkml.kernel.org/r/1471447270-32093-1-git-send-email-vegard.nossum@oracle.com
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
