1 files changed, 18 insertions, 229 deletions

diff --git a/sound/arm/pxa2xx-ac97.c b/sound/arm/pxa2xx-ac97.c
index 714b3baa4be7..c2635beb4c88 100644
--- a/sound/arm/pxa2xx-ac97.c
+++ b/sound/arm/pxa2xx-ac97.c
@@ -12,198 +12,27 @@
 
 #include <linux/init.h>
 #include <linux/module.h>
-#include <linux/kernel.h>
 #include <linux/platform_device.h>
-#include <linux/interrupt.h>
-#include <linux/wait.h>
-#include <linux/clk.h>
-#include <linux/delay.h>
 
 #include <sound/core.h>
 #include <sound/pcm.h>
 #include <sound/ac97_codec.h>
 #include <sound/initval.h>
+#include <sound/pxa2xx-lib.h>
 
-#include <asm/irq.h>
-#include <linux/mutex.h>
 #include <mach/hardware.h>
 #include <mach/pxa-regs.h>
-#include <mach/pxa2xx-gpio.h>
 #include <mach/audio.h>
 
 #include "pxa2xx-pcm.h"
 
-
-static DEFINE_MUTEX(car_mutex);
-static DECLARE_WAIT_QUEUE_HEAD(gsr_wq);
-static volatile long gsr_bits;
-static struct clk *ac97_clk;
-#ifdef CONFIG_PXA27x
-static struct clk *ac97conf_clk;
-#endif
-
-/*
- * Beware PXA27x bugs:
- *
- *   o Slot 12 read from modem space will hang controller.
- *   o CDONE, SDONE interrupt fails after any slot 12 IO.
- *
- * We therefore have an hybrid approach for waiting on SDONE (interrupt or
- * 1 jiffy timeout if interrupt never comes).
- */ 
-
-static unsigned short pxa2xx_ac97_read(struct snd_ac97 *ac97, unsigned short reg)
-{
-	unsigned short val = -1;
-	volatile u32 *reg_addr;
-
-	mutex_lock(&car_mutex);
-
-	/* set up primary or secondary codec space */
-	reg_addr = (ac97->num & 1) ? &SAC_REG_BASE : &PAC_REG_BASE;
-	reg_addr += (reg >> 1);
-
-	/* start read access across the ac97 link */
-	GSR = GSR_CDONE | GSR_SDONE;
-	gsr_bits = 0;
-	val = *reg_addr;
-	if (reg == AC97_GPIO_STATUS)
-		goto out;
-	if (wait_event_timeout(gsr_wq, (GSR | gsr_bits) & GSR_SDONE, 1) <= 0 &&
-	    !((GSR | gsr_bits) & GSR_SDONE)) {
-		printk(KERN_ERR "%s: read error (ac97_reg=%d GSR=%#lx)\n",
-				__func__, reg, GSR | gsr_bits);
-		val = -1;
-		goto out;
-	}
-
-	/* valid data now */
-	GSR = GSR_CDONE | GSR_SDONE;
-	gsr_bits = 0;
-	val = *reg_addr;			
-	/* but we've just started another cycle... */
-	wait_event_timeout(gsr_wq, (GSR | gsr_bits) & GSR_SDONE, 1);
-
-out:	mutex_unlock(&car_mutex);
-	return val;
-}
-
-static void pxa2xx_ac97_write(struct snd_ac97 *ac97, unsigned short reg, unsigned short val)
-{
-	volatile u32 *reg_addr;
-
-	mutex_lock(&car_mutex);
-
-	/* set up primary or secondary codec space */
-	reg_addr = (ac97->num & 1) ? &SAC_REG_BASE : &PAC_REG_BASE;
-	reg_addr += (reg >> 1);
-
-	GSR = GSR_CDONE | GSR_SDONE;
-	gsr_bits = 0;
-	*reg_addr = val;
-	if (wait_event_timeout(gsr_wq, (GSR | gsr_bits) & GSR_CDONE, 1) <= 0 &&
-	    !((GSR | gsr_bits) & GSR_CDONE))
-		printk(KERN_ERR "%s: write error (ac97_reg=%d GSR=%#lx)\n",
-				__func__, reg, GSR | gsr_bits);
-
-	mutex_unlock(&car_mutex);
-}
-
 static void pxa2xx_ac97_reset(struct snd_ac97 *ac97)
 {
-	/* First, try cold reset */
-#ifdef CONFIG_PXA3xx
-	int timeout;
-
-	/* Hold CLKBPB for 100us */
-	GCR = 0;
-	GCR = GCR_CLKBPB;
-	udelay(100);
-	GCR = 0;
-#endif
-
-	GCR &=  GCR_COLD_RST;  /* clear everything but nCRST */
-	GCR &= ~GCR_COLD_RST;  /* then assert nCRST */
-
-	gsr_bits = 0;
-#ifdef CONFIG_PXA27x
-	/* PXA27x Developers Manual section 13.5.2.2.1 */
-	clk_enable(ac97conf_clk);
-	udelay(5);
-	clk_disable(ac97conf_clk);
-	GCR = GCR_COLD_RST;
-	udelay(50);
-#elif defined(CONFIG_PXA3xx)
-	timeout = 1000;
-	/* Can't use interrupts on PXA3xx */
-	GCR &= ~(GCR_PRIRDY_IEN|GCR_SECRDY_IEN);
-
-	GCR = GCR_WARM_RST | GCR_COLD_RST;
-	while (!(GSR & (GSR_PCR | GSR_SCR)) && timeout--)
-		mdelay(10);
-#else
-	GCR = GCR_COLD_RST;
-	GCR |= GCR_CDONE_IE|GCR_SDONE_IE;
-	wait_event_timeout(gsr_wq, gsr_bits & (GSR_PCR | GSR_SCR), 1);
-#endif
-
-	if (!((GSR | gsr_bits) & (GSR_PCR | GSR_SCR))) {
-		printk(KERN_INFO "%s: cold reset timeout (GSR=%#lx)\n",
-				 __func__, gsr_bits);
-
-		/* let's try warm reset */
-		gsr_bits = 0;
-#ifdef CONFIG_PXA27x
-		/* warm reset broken on Bulverde,
-		   so manually keep AC97 reset high */
-		pxa_gpio_mode(113 | GPIO_OUT | GPIO_DFLT_HIGH); 
-		udelay(10);
-		GCR |= GCR_WARM_RST;
-		pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT);
-		udelay(500);
-#elif defined(CONFIG_PXA3xx)
-		timeout = 100;
-		/* Can't use interrupts */
-		GCR |= GCR_WARM_RST;
-		while (!((GSR | gsr_bits) & (GSR_PCR | GSR_SCR)) && timeout--)
-			mdelay(1);
-#else
-		GCR |= GCR_WARM_RST|GCR_PRIRDY_IEN|GCR_SECRDY_IEN;
-		wait_event_timeout(gsr_wq, gsr_bits & (GSR_PCR | GSR_SCR), 1);
-#endif			
-
-		if (!((GSR | gsr_bits) & (GSR_PCR | GSR_SCR)))
-			printk(KERN_INFO "%s: warm reset timeout (GSR=%#lx)\n",
-					 __func__, gsr_bits);
-	}
-
-	GCR &= ~(GCR_PRIRDY_IEN|GCR_SECRDY_IEN);
-	GCR |= GCR_SDONE_IE|GCR_CDONE_IE;
-}
-
-static irqreturn_t pxa2xx_ac97_irq(int irq, void *dev_id)
-{
-	long status;
-
-	status = GSR;
-	if (status) {
-		GSR = status;
-		gsr_bits |= status;
-		wake_up(&gsr_wq);
-
-#ifdef CONFIG_PXA27x
-		/* Although we don't use those we still need to clear them
-		   since they tend to spuriously trigger when MMC is used
-		   (hardware bug? go figure)... */
-		MISR = MISR_EOC;
-		PISR = PISR_EOC;
-		MCSR = MCSR_EOC;
-#endif
-
-		return IRQ_HANDLED;
+	if (!pxa2xx_ac97_try_cold_reset(ac97)) {
+		pxa2xx_ac97_try_warm_reset(ac97);
 	}
 
-	return IRQ_NONE;
+	pxa2xx_ac97_finish_reset(ac97);
 }
 
 static struct snd_ac97_bus_ops pxa2xx_ac97_ops = {
@@ -288,17 +117,19 @@ static int pxa2xx_ac97_do_suspend(struct snd_card *card, pm_message_t state)
 	snd_ac97_suspend(pxa2xx_ac97_ac97);
 	if (platform_ops && platform_ops->suspend)
 		platform_ops->suspend(platform_ops->priv);
-	GCR |= GCR_ACLINK_OFF;
-	clk_disable(ac97_clk);
 
-	return 0;
+	return pxa2xx_ac97_hw_suspend();
 }
 
 static int pxa2xx_ac97_do_resume(struct snd_card *card)
 {
 	pxa2xx_audio_ops_t *platform_ops = card->dev->platform_data;
+	int rc;
+
+	rc = pxa2xx_ac97_hw_resume();
+	if (rc)
+		return rc;
 
-	clk_enable(ac97_clk);
 	if (platform_ops && platform_ops->resume)
 		platform_ops->resume(platform_ops->priv);
 	snd_ac97_resume(pxa2xx_ac97_ac97);
@@ -354,40 +185,17 @@ static int __devinit pxa2xx_ac97_probe(struct platform_device *dev)
 	if (ret)
 		goto err;
 
-	ret = request_irq(IRQ_AC97, pxa2xx_ac97_irq, 0, "AC97", NULL);
-	if (ret < 0)
-		goto err;
-
-	pxa_gpio_mode(GPIO31_SYNC_AC97_MD);
-	pxa_gpio_mode(GPIO30_SDATA_OUT_AC97_MD);
-	pxa_gpio_mode(GPIO28_BITCLK_AC97_MD);
-	pxa_gpio_mode(GPIO29_SDATA_IN_AC97_MD);
-#ifdef CONFIG_PXA27x
-	/* Use GPIO 113 as AC97 Reset on Bulverde */
-	pxa_gpio_mode(113 | GPIO_ALT_FN_2_OUT);
-	ac97conf_clk = clk_get(&dev->dev, "AC97CONFCLK");
-	if (IS_ERR(ac97conf_clk)) {
-		ret = PTR_ERR(ac97conf_clk);
-		ac97conf_clk = NULL;
-		goto err;
-	}
-#endif
-
-	ac97_clk = clk_get(&dev->dev, "AC97CLK");
-	if (IS_ERR(ac97_clk)) {
-		ret = PTR_ERR(ac97_clk);
-		ac97_clk = NULL;
+	ret = pxa2xx_ac97_hw_probe(dev);
+	if (ret)
 		goto err;
-	}
-	clk_enable(ac97_clk);
 
 	ret = snd_ac97_bus(card, 0, &pxa2xx_ac97_ops, NULL, &ac97_bus);
 	if (ret)
-		goto err;
+		goto err_remove;
 	memset(&ac97_template, 0, sizeof(ac97_template));
 	ret = snd_ac97_mixer(ac97_bus, &ac97_template, &pxa2xx_ac97_ac97);
 	if (ret)
-		goto err;
+		goto err_remove;
 
 	snprintf(card->shortname, sizeof(card->shortname),
 		 "%s", snd_ac97_get_short_name(pxa2xx_ac97_ac97));
@@ -401,22 +209,11 @@ static int __devinit pxa2xx_ac97_probe(struct platform_device *dev)
 		return 0;
 	}
 
- err:
+err_remove:
+	pxa2xx_ac97_hw_remove(dev);
+err:
 	if (card)
 		snd_card_free(card);
-	if (ac97_clk) {
-		GCR |= GCR_ACLINK_OFF;
-		free_irq(IRQ_AC97, NULL);
-		clk_disable(ac97_clk);
-		clk_put(ac97_clk);
-		ac97_clk = NULL;
-	}
-#ifdef CONFIG_PXA27x
-	if (ac97conf_clk) {
-		clk_put(ac97conf_clk);
-		ac97conf_clk = NULL;
-	}
-#endif
 	return ret;
 }
 
@@ -427,15 +224,7 @@ static int __devexit pxa2xx_ac97_remove(struct platform_device *dev)
 	if (card) {
 		snd_card_free(card);
 		platform_set_drvdata(dev, NULL);
-		GCR |= GCR_ACLINK_OFF;
-		free_irq(IRQ_AC97, NULL);
-		clk_disable(ac97_clk);
-		clk_put(ac97_clk);
-		ac97_clk = NULL;
-#ifdef CONFIG_PXA27x
-		clk_put(ac97conf_clk);
-		ac97conf_clk = NULL;
-#endif
+		pxa2xx_ac97_hw_remove(dev);
 	}
 
 	return 0;