diff options
Diffstat (limited to 'net/dsa/mv88e6123_61_65.c')
| -rw-r--r-- | net/dsa/mv88e6123_61_65.c | 92 |
1 files changed, 59 insertions, 33 deletions
diff --git a/net/dsa/mv88e6123_61_65.c b/net/dsa/mv88e6123_61_65.c index 100318722214..52faaa21a4d9 100644 --- a/net/dsa/mv88e6123_61_65.c +++ b/net/dsa/mv88e6123_61_65.c @@ -1,6 +1,6 @@ /* * net/dsa/mv88e6123_61_65.c - Marvell 88e6123/6161/6165 switch chip support - * Copyright (c) 2008 Marvell Semiconductor + * Copyright (c) 2008-2009 Marvell Semiconductor * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -98,17 +98,17 @@ static int mv88e6123_61_65_setup_global(struct dsa_switch *ds) return ret; /* - * Configure the cpu port, and configure the cpu port as the - * port to which ingress and egress monitor frames are to be - * sent. + * Configure the upstream port, and configure the upstream + * port as the port to which ingress and egress monitor frames + * are to be sent. */ - REG_WRITE(REG_GLOBAL, 0x1a, (ds->cpu_port * 0x1110)); + REG_WRITE(REG_GLOBAL, 0x1a, (dsa_upstream_port(ds) * 0x1110)); /* * Disable remote management for now, and set the switch's - * DSA device number to zero. + * DSA device number. */ - REG_WRITE(REG_GLOBAL, 0x1c, 0x0000); + REG_WRITE(REG_GLOBAL, 0x1c, ds->index & 0x1f); /* * Send all frames with destination addresses matching @@ -133,10 +133,17 @@ static int mv88e6123_61_65_setup_global(struct dsa_switch *ds) REG_WRITE(REG_GLOBAL2, 0x05, 0x00ff); /* - * Map all DSA device IDs to the CPU port. + * Program the DSA routing table. */ - for (i = 0; i < 32; i++) - REG_WRITE(REG_GLOBAL2, 0x06, 0x8000 | (i << 8) | ds->cpu_port); + for (i = 0; i < 32; i++) { + int nexthop; + + nexthop = 0x1f; + if (i != ds->index && i < ds->dst->pd->nr_chips) + nexthop = ds->pd->rtable[i] & 0x1f; + + REG_WRITE(REG_GLOBAL2, 0x06, 0x8000 | (i << 8) | nexthop); + } /* * Clear all trunk masks. @@ -176,12 +183,18 @@ static int mv88e6123_61_65_setup_global(struct dsa_switch *ds) static int mv88e6123_61_65_setup_port(struct dsa_switch *ds, int p) { int addr = REG_PORT(p); + u16 val; /* * MAC Forcing register: don't force link, speed, duplex - * or flow control state to any particular values. + * or flow control state to any particular values on physical + * ports, but force the CPU port and all DSA ports to 1000 Mb/s + * full duplex. */ - REG_WRITE(addr, 0x01, 0x0003); + if (dsa_is_cpu_port(ds, p) || ds->dsa_port_mask & (1 << p)) + REG_WRITE(addr, 0x01, 0x003e); + else + REG_WRITE(addr, 0x01, 0x0003); /* * Do not limit the period of time that this port can be @@ -192,37 +205,50 @@ static int mv88e6123_61_65_setup_port(struct dsa_switch *ds, int p) /* * Port Control: disable Drop-on-Unlock, disable Drop-on-Lock, - * configure the requested (DSA/EDSA) tagging mode if this is - * the CPU port, disable Header mode, enable IGMP/MLD snooping, - * disable VLAN tunneling, determine priority by looking at - * 802.1p and IP priority fields (IP prio has precedence), and - * set STP state to Forwarding. Finally, if this is the CPU - * port, additionally enable forwarding of unknown unicast and - * multicast addresses. - */ - REG_WRITE(addr, 0x04, - (p == ds->cpu_port) ? - (ds->tag_protocol == htons(ETH_P_DSA)) ? - 0x053f : 0x373f : - 0x0433); + * disable Header mode, enable IGMP/MLD snooping, disable VLAN + * tunneling, determine priority by looking at 802.1p and IP + * priority fields (IP prio has precedence), and set STP state + * to Forwarding. + * + * If this is the CPU link, use DSA or EDSA tagging depending + * on which tagging mode was configured. + * + * If this is a link to another switch, use DSA tagging mode. + * + * If this is the upstream port for this switch, enable + * forwarding of unknown unicasts and multicasts. + */ + val = 0x0433; + if (dsa_is_cpu_port(ds, p)) { + if (ds->dst->tag_protocol == htons(ETH_P_EDSA)) + val |= 0x3300; + else + val |= 0x0100; + } + if (ds->dsa_port_mask & (1 << p)) + val |= 0x0100; + if (p == dsa_upstream_port(ds)) + val |= 0x000c; + REG_WRITE(addr, 0x04, val); /* * Port Control 1: disable trunking. Also, if this is the * CPU port, enable learn messages to be sent to this port. */ - REG_WRITE(addr, 0x05, (p == ds->cpu_port) ? 0x8000 : 0x0000); + REG_WRITE(addr, 0x05, dsa_is_cpu_port(ds, p) ? 0x8000 : 0x0000); /* * Port based VLAN map: give each port its own address * database, allow the CPU port to talk to each of the 'real' * ports, and allow each of the 'real' ports to only talk to - * the CPU port. - */ - REG_WRITE(addr, 0x06, - ((p & 0xf) << 12) | - ((p == ds->cpu_port) ? - ds->valid_port_mask : - (1 << ds->cpu_port))); + * the upstream port. + */ + val = (p & 0xf) << 12; + if (dsa_is_cpu_port(ds, p)) + val |= ds->phys_port_mask; + else + val |= 1 << dsa_upstream_port(ds); + REG_WRITE(addr, 0x06, val); /* * Default VLAN ID and priority: don't set a default VLAN |