diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/net/cfg80211.h | 6 | ||||
| -rw-r--r-- | include/uapi/linux/nl80211.h | 21 |
2 files changed, 27 insertions, 0 deletions
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 738b4d8a4666..41ae3f500957 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -2742,6 +2742,8 @@ struct cfg80211_nan_func { * @nan_change_conf: changes NAN configuration. The changed parameters must * be specified in @changes (using &enum cfg80211_nan_conf_changes); * All other parameters must be ignored. + * + * @set_multicast_to_unicast: configure multicast to unicast conversion for BSS */ struct cfg80211_ops { int (*suspend)(struct wiphy *wiphy, struct cfg80211_wowlan *wow); @@ -3018,6 +3020,10 @@ struct cfg80211_ops { struct wireless_dev *wdev, struct cfg80211_nan_conf *conf, u32 changes); + + int (*set_multicast_to_unicast)(struct wiphy *wiphy, + struct net_device *dev, + const bool enabled); }; /* diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index a268a009528a..e21d23dcb588 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -600,6 +600,20 @@ * * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface. * + * @NL80211_CMD_SET_MULTICAST_TO_UNICAST: Configure if this AP should perform + * multicast to unicast conversion. When enabled, all multicast packets + * with ethertype ARP, IPv4 or IPv6 (possibly within an 802.1Q header) + * will be sent out to each station once with the destination (multicast) + * MAC address replaced by the station's MAC address. Note that this may + * break certain expectations of the receiver, e.g. the ability to drop + * unicast IP packets encapsulated in multicast L2 frames, or the ability + * to not send destination unreachable messages in such cases. + * This can only be toggled per BSS. Configure this on an interface of + * type %NL80211_IFTYPE_AP. It applies to all its VLAN interfaces + * (%NL80211_IFTYPE_AP_VLAN), except for those in 4addr (WDS) mode. + * If %NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED is not present with this + * command, the feature is disabled. + * * @NL80211_CMD_JOIN_MESH: Join a mesh. The mesh ID must be given, and initial * mesh config parameters may be given. * @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the @@ -1069,6 +1083,8 @@ enum nl80211_commands { NL80211_CMD_CHANGE_NAN_CONFIG, NL80211_CMD_NAN_MATCH, + NL80211_CMD_SET_MULTICAST_TO_UNICAST, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -1950,6 +1966,9 @@ enum nl80211_commands { * Request/Response frame protection. This attribute contains the 16 octet * STA Nonce followed by 16 octets of AP Nonce. * + * @NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED: Indicates whether or not multicast + * packets should be send out as unicast to all stations (flag attribute). + * * @NUM_NL80211_ATTR: total number of nl80211_attrs available * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use @@ -2352,6 +2371,8 @@ enum nl80211_attrs { NL80211_ATTR_FILS_KEK, NL80211_ATTR_FILS_NONCES, + NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, |