diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/linux/fsl_devices.h | 20 | ||||
| -rw-r--r-- | include/linux/platform_data/atmel.h | 12 | ||||
| -rw-r--r-- | include/linux/usb/chipidea.h | 15 | ||||
| -rw-r--r-- | include/linux/usb/composite.h | 2 | ||||
| -rw-r--r-- | include/linux/usb/gadget.h | 198 | ||||
| -rw-r--r-- | include/linux/usb/hcd.h | 6 | ||||
| -rw-r--r-- | include/linux/usb/msm_hsusb.h | 9 | ||||
| -rw-r--r-- | include/linux/usb/of.h | 7 | ||||
| -rw-r--r-- | include/linux/usb/otg.h | 15 | ||||
| -rw-r--r-- | include/uapi/linux/usb/ch9.h | 12 |
10 files changed, 266 insertions, 30 deletions
diff --git a/include/linux/fsl_devices.h b/include/linux/fsl_devices.h index 2a2f56b292c1..f2912914141a 100644 --- a/include/linux/fsl_devices.h +++ b/include/linux/fsl_devices.h @@ -20,11 +20,6 @@ #define FSL_UTMI_PHY_DLY 10 /*As per P1010RM, delay for UTMI PHY CLK to become stable - 10ms*/ #define FSL_USB_PHY_CLK_TIMEOUT 10000 /* uSec */ -#define FSL_USB_VER_OLD 0 -#define FSL_USB_VER_1_6 1 -#define FSL_USB_VER_2_2 2 -#define FSL_USB_VER_2_4 3 -#define FSL_USB_VER_2_5 4 #include <linux/types.h> @@ -52,6 +47,15 @@ * */ +enum fsl_usb2_controller_ver { + FSL_USB_VER_NONE = -1, + FSL_USB_VER_OLD = 0, + FSL_USB_VER_1_6 = 1, + FSL_USB_VER_2_2 = 2, + FSL_USB_VER_2_4 = 3, + FSL_USB_VER_2_5 = 4, +}; + enum fsl_usb2_operating_modes { FSL_USB2_MPH_HOST, FSL_USB2_DR_HOST, @@ -65,6 +69,7 @@ enum fsl_usb2_phy_modes { FSL_USB2_PHY_UTMI, FSL_USB2_PHY_UTMI_WIDE, FSL_USB2_PHY_SERIAL, + FSL_USB2_PHY_UTMI_DUAL, }; struct clk; @@ -72,7 +77,7 @@ struct platform_device; struct fsl_usb2_platform_data { /* board specific information */ - int controller_ver; + enum fsl_usb2_controller_ver controller_ver; enum fsl_usb2_operating_modes operating_mode; enum fsl_usb2_phy_modes phy_mode; unsigned int port_enables; @@ -93,6 +98,9 @@ struct fsl_usb2_platform_data { unsigned suspended:1; unsigned already_suspended:1; + unsigned has_fsl_erratum_a007792:1; + unsigned has_fsl_erratum_a005275:1; + unsigned check_phy_clk_valid:1; /* register save area for suspend/resume */ u32 pm_command; diff --git a/include/linux/platform_data/atmel.h b/include/linux/platform_data/atmel.h index 4b452c6a2f7b..527a85c61924 100644 --- a/include/linux/platform_data/atmel.h +++ b/include/linux/platform_data/atmel.h @@ -46,18 +46,6 @@ struct at91_cf_data { #define AT91_IDE_SWAP_A0_A2 0x02 }; - /* USB Host */ -#define AT91_MAX_USBH_PORTS 3 -struct at91_usbh_data { - int vbus_pin[AT91_MAX_USBH_PORTS]; /* port power-control pin */ - int overcurrent_pin[AT91_MAX_USBH_PORTS]; - u8 ports; /* number of ports on root hub */ - u8 overcurrent_supported; - u8 vbus_pin_active_low[AT91_MAX_USBH_PORTS]; - u8 overcurrent_status[AT91_MAX_USBH_PORTS]; - u8 overcurrent_changed[AT91_MAX_USBH_PORTS]; -}; - /* NAND / SmartMedia */ struct atmel_nand_data { int enable_pin; /* chip enable */ diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h index ab94f78c4dd1..a41833cd184c 100644 --- a/include/linux/usb/chipidea.h +++ b/include/linux/usb/chipidea.h @@ -19,8 +19,11 @@ struct ci_hdrc_platform_data { enum usb_phy_interface phy_mode; unsigned long flags; #define CI_HDRC_REGS_SHARED BIT(0) +#define CI_HDRC_DISABLE_DEVICE_STREAMING BIT(1) #define CI_HDRC_SUPPORTS_RUNTIME_PM BIT(2) -#define CI_HDRC_DISABLE_STREAMING BIT(3) +#define CI_HDRC_DISABLE_HOST_STREAMING BIT(3) +#define CI_HDRC_DISABLE_STREAMING (CI_HDRC_DISABLE_DEVICE_STREAMING | \ + CI_HDRC_DISABLE_HOST_STREAMING) /* * Only set it when DCCPARAMS.DC==1 and DCCPARAMS.HC==1, * but otg is not supported (no register otgsc). @@ -29,12 +32,22 @@ struct ci_hdrc_platform_data { #define CI_HDRC_IMX28_WRITE_FIX BIT(5) #define CI_HDRC_FORCE_FULLSPEED BIT(6) #define CI_HDRC_TURN_VBUS_EARLY_ON BIT(7) +#define CI_HDRC_SET_NON_ZERO_TTHA BIT(8) +#define CI_HDRC_OVERRIDE_AHB_BURST BIT(9) +#define CI_HDRC_OVERRIDE_TX_BURST BIT(10) +#define CI_HDRC_OVERRIDE_RX_BURST BIT(11) enum usb_dr_mode dr_mode; #define CI_HDRC_CONTROLLER_RESET_EVENT 0 #define CI_HDRC_CONTROLLER_STOPPED_EVENT 1 void (*notify_event) (struct ci_hdrc *ci, unsigned event); struct regulator *reg_vbus; + struct usb_otg_caps ci_otg_caps; bool tpl_support; + /* interrupt threshold setting */ + u32 itc_setting; + u32 ahb_burst_config; + u32 tx_burst_size; + u32 rx_burst_size; }; /* Default offset of capability registers */ diff --git a/include/linux/usb/composite.h b/include/linux/usb/composite.h index 2511469a9904..1074b8921a5d 100644 --- a/include/linux/usb/composite.h +++ b/include/linux/usb/composite.h @@ -228,6 +228,8 @@ struct usb_function { struct list_head list; DECLARE_BITMAP(endpoints, 32); const struct usb_function_instance *fi; + + unsigned int bind_deactivated:1; }; int usb_add_function(struct usb_configuration *, struct usb_function *); diff --git a/include/linux/usb/gadget.h b/include/linux/usb/gadget.h index 4f3dfb7d0654..c14a69b36d27 100644 --- a/include/linux/usb/gadget.h +++ b/include/linux/usb/gadget.h @@ -141,10 +141,49 @@ struct usb_ep_ops { }; /** + * struct usb_ep_caps - endpoint capabilities description + * @type_control:Endpoint supports control type (reserved for ep0). + * @type_iso:Endpoint supports isochronous transfers. + * @type_bulk:Endpoint supports bulk transfers. + * @type_int:Endpoint supports interrupt transfers. + * @dir_in:Endpoint supports IN direction. + * @dir_out:Endpoint supports OUT direction. + */ +struct usb_ep_caps { + unsigned type_control:1; + unsigned type_iso:1; + unsigned type_bulk:1; + unsigned type_int:1; + unsigned dir_in:1; + unsigned dir_out:1; +}; + +#define USB_EP_CAPS_TYPE_CONTROL 0x01 +#define USB_EP_CAPS_TYPE_ISO 0x02 +#define USB_EP_CAPS_TYPE_BULK 0x04 +#define USB_EP_CAPS_TYPE_INT 0x08 +#define USB_EP_CAPS_TYPE_ALL \ + (USB_EP_CAPS_TYPE_ISO | USB_EP_CAPS_TYPE_BULK | USB_EP_CAPS_TYPE_INT) +#define USB_EP_CAPS_DIR_IN 0x01 +#define USB_EP_CAPS_DIR_OUT 0x02 +#define USB_EP_CAPS_DIR_ALL (USB_EP_CAPS_DIR_IN | USB_EP_CAPS_DIR_OUT) + +#define USB_EP_CAPS(_type, _dir) \ + { \ + .type_control = !!(_type & USB_EP_CAPS_TYPE_CONTROL), \ + .type_iso = !!(_type & USB_EP_CAPS_TYPE_ISO), \ + .type_bulk = !!(_type & USB_EP_CAPS_TYPE_BULK), \ + .type_int = !!(_type & USB_EP_CAPS_TYPE_INT), \ + .dir_in = !!(_dir & USB_EP_CAPS_DIR_IN), \ + .dir_out = !!(_dir & USB_EP_CAPS_DIR_OUT), \ + } + +/** * struct usb_ep - device side representation of USB endpoint * @name:identifier for the endpoint, such as "ep-a" or "ep9in-bulk" * @ops: Function pointers used to access hardware-specific operations. * @ep_list:the gadget's ep_list holds all of its endpoints + * @caps:The structure describing types and directions supported by endoint. * @maxpacket:The maximum packet size used on this endpoint. The initial * value can sometimes be reduced (hardware allowing), according to * the endpoint descriptor used to configure the endpoint. @@ -167,12 +206,15 @@ struct usb_ep_ops { * gadget->ep_list. the control endpoint (gadget->ep0) is not in that list, * and is accessed only in response to a driver setup() callback. */ + struct usb_ep { void *driver_data; const char *name; const struct usb_ep_ops *ops; struct list_head ep_list; + struct usb_ep_caps caps; + bool claimed; unsigned maxpacket:16; unsigned maxpacket_limit:16; unsigned max_streams:16; @@ -492,6 +534,9 @@ struct usb_gadget_ops { int (*udc_start)(struct usb_gadget *, struct usb_gadget_driver *); int (*udc_stop)(struct usb_gadget *); + struct usb_ep *(*match_ep)(struct usb_gadget *, + struct usb_endpoint_descriptor *, + struct usb_ss_ep_comp_descriptor *); }; /** @@ -511,6 +556,7 @@ struct usb_gadget_ops { * @dev: Driver model state for this abstract device. * @out_epnum: last used out ep number * @in_epnum: last used in ep number + * @otg_caps: OTG capabilities of this gadget. * @sg_supported: true if we can handle scatter-gather * @is_otg: True if the USB device port uses a Mini-AB jack, so that the * gadget driver must provide a USB OTG descriptor. @@ -526,6 +572,9 @@ struct usb_gadget_ops { * @quirk_ep_out_aligned_size: epout requires buffer size to be aligned to * MaxPacketSize. * @is_selfpowered: if the gadget is self-powered. + * @deactivated: True if gadget is deactivated - in deactivated state it cannot + * be connected. + * @connected: True if gadget is connected. * * Gadgets have a mostly-portable "gadget driver" implementing device * functions, handling all usb configurations and interfaces. Gadget @@ -559,6 +608,7 @@ struct usb_gadget { struct device dev; unsigned out_epnum; unsigned in_epnum; + struct usb_otg_caps *otg_caps; unsigned sg_supported:1; unsigned is_otg:1; @@ -567,7 +617,12 @@ struct usb_gadget { unsigned a_hnp_support:1; unsigned a_alt_hnp_support:1; unsigned quirk_ep_out_aligned_size:1; + unsigned quirk_altset_not_supp:1; + unsigned quirk_stall_not_supp:1; + unsigned quirk_zlp_not_supp:1; unsigned is_selfpowered:1; + unsigned deactivated:1; + unsigned connected:1; }; #define work_to_gadget(w) (container_of((w), struct usb_gadget, work)) @@ -584,7 +639,6 @@ static inline struct usb_gadget *dev_to_usb_gadget(struct device *dev) #define gadget_for_each_ep(tmp, gadget) \ list_for_each_entry(tmp, &(gadget)->ep_list, ep_list) - /** * usb_ep_align_maybe - returns @len aligned to ep's maxpacketsize if gadget * requires quirk_ep_out_aligned_size, otherwise reguens len. @@ -603,6 +657,34 @@ usb_ep_align_maybe(struct usb_gadget *g, struct usb_ep *ep, size_t len) } /** + * gadget_is_altset_supported - return true iff the hardware supports + * altsettings + * @g: controller to check for quirk + */ +static inline int gadget_is_altset_supported(struct usb_gadget *g) +{ + return !g->quirk_altset_not_supp; +} + +/** + * gadget_is_stall_supported - return true iff the hardware supports stalling + * @g: controller to check for quirk + */ +static inline int gadget_is_stall_supported(struct usb_gadget *g) +{ + return !g->quirk_stall_not_supp; +} + +/** + * gadget_is_zlp_supported - return true iff the hardware supports zlp + * @g: controller to check for quirk + */ +static inline int gadget_is_zlp_supported(struct usb_gadget *g) +{ + return !g->quirk_zlp_not_supp; +} + +/** * gadget_is_dualspeed - return true iff the hardware handles high speed * @g: controller that might support both high and full speeds */ @@ -771,9 +853,24 @@ static inline int usb_gadget_vbus_disconnect(struct usb_gadget *gadget) */ static inline int usb_gadget_connect(struct usb_gadget *gadget) { + int ret; + if (!gadget->ops->pullup) return -EOPNOTSUPP; - return gadget->ops->pullup(gadget, 1); + + if (gadget->deactivated) { + /* + * If gadget is deactivated we only save new state. + * Gadget will be connected automatically after activation. + */ + gadget->connected = true; + return 0; + } + + ret = gadget->ops->pullup(gadget, 1); + if (!ret) + gadget->connected = 1; + return ret; } /** @@ -784,20 +881,88 @@ static inline int usb_gadget_connect(struct usb_gadget *gadget) * as a disconnect (when a VBUS session is active). Not all systems * support software pullup controls. * + * Returns zero on success, else negative errno. + */ +static inline int usb_gadget_disconnect(struct usb_gadget *gadget) +{ + int ret; + + if (!gadget->ops->pullup) + return -EOPNOTSUPP; + + if (gadget->deactivated) { + /* + * If gadget is deactivated we only save new state. + * Gadget will stay disconnected after activation. + */ + gadget->connected = false; + return 0; + } + + ret = gadget->ops->pullup(gadget, 0); + if (!ret) + gadget->connected = 0; + return ret; +} + +/** + * usb_gadget_deactivate - deactivate function which is not ready to work + * @gadget: the peripheral being deactivated + * * This routine may be used during the gadget driver bind() call to prevent * the peripheral from ever being visible to the USB host, unless later - * usb_gadget_connect() is called. For example, user mode components may + * usb_gadget_activate() is called. For example, user mode components may * need to be activated before the system can talk to hosts. * * Returns zero on success, else negative errno. */ -static inline int usb_gadget_disconnect(struct usb_gadget *gadget) +static inline int usb_gadget_deactivate(struct usb_gadget *gadget) { - if (!gadget->ops->pullup) - return -EOPNOTSUPP; - return gadget->ops->pullup(gadget, 0); + int ret; + + if (gadget->deactivated) + return 0; + + if (gadget->connected) { + ret = usb_gadget_disconnect(gadget); + if (ret) + return ret; + /* + * If gadget was being connected before deactivation, we want + * to reconnect it in usb_gadget_activate(). + */ + gadget->connected = true; + } + gadget->deactivated = true; + + return 0; } +/** + * usb_gadget_activate - activate function which is not ready to work + * @gadget: the peripheral being activated + * + * This routine activates gadget which was previously deactivated with + * usb_gadget_deactivate() call. It calls usb_gadget_connect() if needed. + * + * Returns zero on success, else negative errno. + */ +static inline int usb_gadget_activate(struct usb_gadget *gadget) +{ + if (!gadget->deactivated) + return 0; + + gadget->deactivated = false; + + /* + * If gadget has been connected before deactivation, or became connected + * while it was being deactivated, we call usb_gadget_connect(). + */ + if (gadget->connected) + return usb_gadget_connect(gadget); + + return 0; +} /*-------------------------------------------------------------------------*/ @@ -1002,6 +1167,10 @@ int usb_assign_descriptors(struct usb_function *f, struct usb_descriptor_header **ss); void usb_free_all_descriptors(struct usb_function *f); +struct usb_descriptor_header *usb_otg_descriptor_alloc( + struct usb_gadget *gadget); +int usb_otg_descriptor_init(struct usb_gadget *gadget, + struct usb_descriptor_header *otg_desc); /*-------------------------------------------------------------------------*/ /* utility to simplify map/unmap of usb_requests to/from DMA */ @@ -1034,6 +1203,21 @@ extern void usb_gadget_giveback_request(struct usb_ep *ep, /*-------------------------------------------------------------------------*/ +/* utility to find endpoint by name */ + +extern struct usb_ep *gadget_find_ep_by_name(struct usb_gadget *g, + const char *name); + +/*-------------------------------------------------------------------------*/ + +/* utility to check if endpoint caps match descriptor needs */ + +extern int usb_gadget_ep_match_desc(struct usb_gadget *gadget, + struct usb_ep *ep, struct usb_endpoint_descriptor *desc, + struct usb_ss_ep_comp_descriptor *ep_comp); + +/*-------------------------------------------------------------------------*/ + /* utility to update vbus status for udc core, it may be scheduled */ extern void usb_udc_vbus_handler(struct usb_gadget *gadget, bool status); diff --git a/include/linux/usb/hcd.h b/include/linux/usb/hcd.h index c9aa7792de10..d2784c10bfe2 100644 --- a/include/linux/usb/hcd.h +++ b/include/linux/usb/hcd.h @@ -564,9 +564,9 @@ extern void usb_ep0_reinit(struct usb_device *); /*-------------------------------------------------------------------------*/ -/* class requests from USB 3.0 hub spec, table 10-5 */ -#define SetHubDepth (0x3000 | HUB_SET_DEPTH) -#define GetPortErrorCount (0x8000 | HUB_GET_PORT_ERR_COUNT) +/* class requests from USB 3.1 hub spec, table 10-7 */ +#define SetHubDepth (0x2000 | HUB_SET_DEPTH) +#define GetPortErrorCount (0xa300 | HUB_GET_PORT_ERR_COUNT) /* * Generic bandwidth allocation constants/support diff --git a/include/linux/usb/msm_hsusb.h b/include/linux/usb/msm_hsusb.h index e55a1504266e..8c8f6854c993 100644 --- a/include/linux/usb/msm_hsusb.h +++ b/include/linux/usb/msm_hsusb.h @@ -128,7 +128,7 @@ struct msm_otg_platform_data { */ struct msm_usb_cable { struct notifier_block nb; - struct extcon_specific_cable_nb conn; + struct extcon_dev *extcon; }; /** @@ -155,6 +155,10 @@ struct msm_usb_cable { * starting controller using usbcmd run/stop bit. * @vbus: VBUS signal state trakining, using extcon framework * @id: ID signal state trakining, using extcon framework + * @switch_gpio: Descriptor for GPIO used to control external Dual + * SPDT USB Switch. + * @reboot: Used to inform the driver to route USB D+/D- line to Device + * connector */ struct msm_otg { struct usb_phy phy; @@ -188,6 +192,9 @@ struct msm_otg { struct msm_usb_cable vbus; struct msm_usb_cable id; + + struct gpio_desc *switch_gpio; + struct notifier_block reboot; }; #endif diff --git a/include/linux/usb/of.h b/include/linux/usb/of.h index cfe0528cdbb1..8c5a818ec244 100644 --- a/include/linux/usb/of.h +++ b/include/linux/usb/of.h @@ -15,6 +15,8 @@ enum usb_dr_mode of_usb_get_dr_mode(struct device_node *np); enum usb_device_speed of_usb_get_maximum_speed(struct device_node *np); bool of_usb_host_tpl_support(struct device_node *np); +int of_usb_update_otg_caps(struct device_node *np, + struct usb_otg_caps *otg_caps); #else static inline enum usb_dr_mode of_usb_get_dr_mode(struct device_node *np) { @@ -30,6 +32,11 @@ static inline bool of_usb_host_tpl_support(struct device_node *np) { return false; } +static inline int of_usb_update_otg_caps(struct device_node *np, + struct usb_otg_caps *otg_caps) +{ + return 0; +} #endif #if IS_ENABLED(CONFIG_OF) && IS_ENABLED(CONFIG_USB_SUPPORT) diff --git a/include/linux/usb/otg.h b/include/linux/usb/otg.h index 52661c5da690..bd1dcf816100 100644 --- a/include/linux/usb/otg.h +++ b/include/linux/usb/otg.h @@ -41,6 +41,21 @@ struct usb_otg { }; +/** + * struct usb_otg_caps - describes the otg capabilities of the device + * @otg_rev: The OTG revision number the device is compliant with, it's + * in binary-coded decimal (i.e. 2.0 is 0200H). + * @hnp_support: Indicates if the device supports HNP. + * @srp_support: Indicates if the device supports SRP. + * @adp_support: Indicates if the device supports ADP. + */ +struct usb_otg_caps { + u16 otg_rev; + bool hnp_support; + bool srp_support; + bool adp_support; +}; + extern const char *usb_otg_state_string(enum usb_otg_state state); /* Context: can sleep */ diff --git a/include/uapi/linux/usb/ch9.h b/include/uapi/linux/usb/ch9.h index aa33fd1b2d4f..f7adc6e01f9e 100644 --- a/include/uapi/linux/usb/ch9.h +++ b/include/uapi/linux/usb/ch9.h @@ -674,9 +674,21 @@ struct usb_otg_descriptor { __u8 bmAttributes; /* support for HNP, SRP, etc */ } __attribute__ ((packed)); +/* USB_DT_OTG (from OTG 2.0 supplement) */ +struct usb_otg20_descriptor { + __u8 bLength; + __u8 bDescriptorType; + + __u8 bmAttributes; /* support for HNP, SRP and ADP, etc */ + __le16 bcdOTG; /* OTG and EH supplement release number + * in binary-coded decimal(i.e. 2.0 is 0200H) + */ +} __attribute__ ((packed)); + /* from usb_otg_descriptor.bmAttributes */ #define USB_OTG_SRP (1 << 0) #define USB_OTG_HNP (1 << 1) /* swap host/device roles */ +#define USB_OTG_ADP (1 << 2) /* support ADP */ /*-------------------------------------------------------------------------*/ |