diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/linux/gpio/driver.h | 25 | ||||
| -rw-r--r-- | include/linux/i2c/sx150x.h | 82 | ||||
| -rw-r--r-- | include/linux/platform_data/gpio-dwapb.h | 3 |
3 files changed, 25 insertions, 85 deletions
diff --git a/include/linux/gpio/driver.h b/include/linux/gpio/driver.h index bee976f82788..50882e09289b 100644 --- a/include/linux/gpio/driver.h +++ b/include/linux/gpio/driver.h @@ -20,6 +20,18 @@ struct gpio_device; #ifdef CONFIG_GPIOLIB /** + * enum single_ended_mode - mode for single ended operation + * @LINE_MODE_PUSH_PULL: normal mode for a GPIO line, drive actively high/low + * @LINE_MODE_OPEN_DRAIN: set line to be open drain + * @LINE_MODE_OPEN_SOURCE: set line to be open source + */ +enum single_ended_mode { + LINE_MODE_PUSH_PULL, + LINE_MODE_OPEN_DRAIN, + LINE_MODE_OPEN_SOURCE, +}; + +/** * struct gpio_chip - abstract a GPIO controller * @label: a functional name for the GPIO device, such as a part * number or the name of the SoC IP-block implementing it. @@ -38,7 +50,15 @@ struct gpio_device; * @set: assigns output value for signal "offset" * @set_multiple: assigns output values for multiple signals defined by "mask" * @set_debounce: optional hook for setting debounce time for specified gpio in - * interrupt triggered gpio chips + * interrupt triggered gpio chips + * @set_single_ended: optional hook for setting a line as open drain, open + * source, or non-single ended (restore from open drain/source to normal + * push-pull mode) this should be implemented if the hardware supports + * open drain or open source settings. The GPIOlib will otherwise try + * to emulate open drain/source by not actively driving lines high/low + * if a consumer request this. The driver may return -ENOTSUPP if e.g. + * it supports just open drain but not open source and is called + * with LINE_MODE_OPEN_SOURCE as mode argument. * @to_irq: optional hook supporting non-static gpio_to_irq() mappings; * implementation may not sleep * @dbg_show: optional routine to show contents in debugfs; default code @@ -130,6 +150,9 @@ struct gpio_chip { int (*set_debounce)(struct gpio_chip *chip, unsigned offset, unsigned debounce); + int (*set_single_ended)(struct gpio_chip *chip, + unsigned offset, + enum single_ended_mode mode); int (*to_irq)(struct gpio_chip *chip, unsigned offset); diff --git a/include/linux/i2c/sx150x.h b/include/linux/i2c/sx150x.h deleted file mode 100644 index 52baa79d69a7..000000000000 --- a/include/linux/i2c/sx150x.h +++ /dev/null @@ -1,82 +0,0 @@ -/* - * Driver for the Semtech SX150x I2C GPIO Expanders - * - * Copyright (c) 2010, Code Aurora Forum. All rights reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 and - * only version 2 as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA - * 02110-1301, USA. - */ -#ifndef __LINUX_I2C_SX150X_H -#define __LINUX_I2C_SX150X_H - -/** - * struct sx150x_platform_data - config data for SX150x driver - * @gpio_base: The index number of the first GPIO assigned to this - * GPIO expander. The expander will create a block of - * consecutively numbered gpios beginning at the given base, - * with the size of the block depending on the model of the - * expander chip. - * @oscio_is_gpo: If set to true, the driver will configure OSCIO as a GPO - * instead of as an oscillator, increasing the size of the - * GP(I)O pool created by this expander by one. The - * output-only GPO pin will be added at the end of the block. - * @io_pullup_ena: A bit-mask which enables or disables the pull-up resistor - * for each IO line in the expander. Setting the bit at - * position n will enable the pull-up for the IO at - * the corresponding offset. For chips with fewer than - * 16 IO pins, high-end bits are ignored. - * @io_pulldn_ena: A bit-mask which enables-or disables the pull-down - * resistor for each IO line in the expander. Setting the - * bit at position n will enable the pull-down for the IO at - * the corresponding offset. For chips with fewer than - * 16 IO pins, high-end bits are ignored. - * @io_open_drain_ena: A bit-mask which enables-or disables open-drain - * operation for each IO line in the expander. Setting the - * bit at position n enables open-drain operation for - * the IO at the corresponding offset. Clearing the bit - * enables regular push-pull operation for that IO. - * For chips with fewer than 16 IO pins, high-end bits - * are ignored. - * @io_polarity: A bit-mask which enables polarity inversion for each IO line - * in the expander. Setting the bit at position n inverts - * the polarity of that IO line, while clearing it results - * in normal polarity. For chips with fewer than 16 IO pins, - * high-end bits are ignored. - * @irq_summary: The 'summary IRQ' line to which the GPIO expander's INT line - * is connected, via which it reports interrupt events - * across all GPIO lines. This must be a real, - * pre-existing IRQ line. - * Setting this value < 0 disables the irq_chip functionality - * of the driver. - * @irq_base: The first 'virtual IRQ' line at which our block of GPIO-based - * IRQ lines will appear. Similarly to gpio_base, the expander - * will create a block of irqs beginning at this number. - * This value is ignored if irq_summary is < 0. - * @reset_during_probe: If set to true, the driver will trigger a full - * reset of the chip at the beginning of the probe - * in order to place it in a known state. - */ -struct sx150x_platform_data { - unsigned gpio_base; - bool oscio_is_gpo; - u16 io_pullup_ena; - u16 io_pulldn_ena; - u16 io_open_drain_ena; - u16 io_polarity; - int irq_summary; - unsigned irq_base; - bool reset_during_probe; -}; - -#endif /* __LINUX_I2C_SX150X_H */ diff --git a/include/linux/platform_data/gpio-dwapb.h b/include/linux/platform_data/gpio-dwapb.h index 28702c849af1..2dc7f4a8ab09 100644 --- a/include/linux/platform_data/gpio-dwapb.h +++ b/include/linux/platform_data/gpio-dwapb.h @@ -15,8 +15,7 @@ #define GPIO_DW_APB_H struct dwapb_port_property { - struct device_node *node; - const char *name; + struct fwnode_handle *fwnode; unsigned int idx; unsigned int ngpio; unsigned int gpio_base; |