summaryrefslogtreecommitdiffstats
path: root/include/net/mac80211.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/net/mac80211.h')
-rw-r--r--include/net/mac80211.h69
1 files changed, 36 insertions, 33 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index 6b1077c2a63f..e3314e516681 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -973,6 +973,10 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
* @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame.
* If this flag is set, the stack cannot do any replay detection
* hence the driver or hardware will have to do that.
+ * @RX_FLAG_PN_VALIDATED: Currently only valid for CCMP/GCMP frames, this
+ * flag indicates that the PN was verified for replay protection.
+ * Note that this flag is also currently only supported when a frame
+ * is also decrypted (ie. @RX_FLAG_DECRYPTED must be set)
* @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
* the frame.
* @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
@@ -997,9 +1001,6 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
* @RX_FLAG_AMPDU_DETAILS: A-MPDU details are known, in particular the reference
* number (@ampdu_reference) must be populated and be a distinct number for
* each A-MPDU
- * @RX_FLAG_AMPDU_REPORT_ZEROLEN: driver reports 0-length subframes
- * @RX_FLAG_AMPDU_IS_ZEROLEN: This is a zero-length subframe, for
- * monitoring purposes only
* @RX_FLAG_AMPDU_LAST_KNOWN: last subframe is known, should be set on all
* subframes of a single A-MPDU
* @RX_FLAG_AMPDU_IS_LAST: this subframe is the last subframe of the A-MPDU
@@ -1039,8 +1040,8 @@ enum mac80211_rx_flags {
RX_FLAG_NO_SIGNAL_VAL = BIT(12),
RX_FLAG_HT_GF = BIT(13),
RX_FLAG_AMPDU_DETAILS = BIT(14),
- RX_FLAG_AMPDU_REPORT_ZEROLEN = BIT(15),
- RX_FLAG_AMPDU_IS_ZEROLEN = BIT(16),
+ RX_FLAG_PN_VALIDATED = BIT(15),
+ /* bit 16 free */
RX_FLAG_AMPDU_LAST_KNOWN = BIT(17),
RX_FLAG_AMPDU_IS_LAST = BIT(18),
RX_FLAG_AMPDU_DELIM_CRC_ERROR = BIT(19),
@@ -1491,8 +1492,10 @@ enum ieee80211_key_flags {
* - Temporal Authenticator Rx MIC Key (64 bits)
* @icv_len: The ICV length for this key type
* @iv_len: The IV length for this key type
+ * @drv_priv: pointer for driver use
*/
struct ieee80211_key_conf {
+ void *drv_priv;
atomic64_t tx_pn;
u32 cipher;
u8 icv_len;
@@ -1675,7 +1678,6 @@ struct ieee80211_sta_rates {
* @tdls: indicates whether the STA is a TDLS peer
* @tdls_initiator: indicates the STA is an initiator of the TDLS link. Only
* valid if the STA is a TDLS peer in the first place.
- * @mfp: indicates whether the STA uses management frame protection or not.
* @txq: per-TID data TX queues (if driver uses the TXQ abstraction)
*/
struct ieee80211_sta {
@@ -1693,7 +1695,6 @@ struct ieee80211_sta {
struct ieee80211_sta_rates __rcu *rates;
bool tdls;
bool tdls_initiator;
- bool mfp;
struct ieee80211_txq *txq[IEEE80211_NUM_TIDS];
@@ -1888,6 +1889,9 @@ struct ieee80211_txq {
* @IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS: The HW supports scanning on all bands
* in one command, mac80211 doesn't have to run separate scans per band.
*
+ * @IEEE80211_HW_TDLS_WIDER_BW: The device/driver supports wider bandwidth
+ * than then BSS bandwidth for a TDLS link on the base channel.
+ *
* @NUM_IEEE80211_HW_FLAGS: number of hardware flags, used for sizing arrays
*/
enum ieee80211_hw_flags {
@@ -1920,6 +1924,7 @@ enum ieee80211_hw_flags {
IEEE80211_HW_CHANCTX_STA_CSA,
IEEE80211_HW_SUPPORTS_CLONED_SKBS,
IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS,
+ IEEE80211_HW_TDLS_WIDER_BW,
/* keep last, obviously */
NUM_IEEE80211_HW_FLAGS
@@ -3696,20 +3701,28 @@ void ieee80211_free_hw(struct ieee80211_hw *hw);
void ieee80211_restart_hw(struct ieee80211_hw *hw);
/**
- * ieee80211_napi_add - initialize mac80211 NAPI context
- * @hw: the hardware to initialize the NAPI context on
- * @napi: the NAPI context to initialize
- * @napi_dev: dummy NAPI netdevice, here to not waste the space if the
- * driver doesn't use NAPI
- * @poll: poll function
- * @weight: default weight
+ * ieee80211_rx_napi - receive frame from NAPI context
+ *
+ * Use this function to hand received frames to mac80211. The receive
+ * buffer in @skb must start with an IEEE 802.11 header. In case of a
+ * paged @skb is used, the driver is recommended to put the ieee80211
+ * header of the frame on the linear part of the @skb to avoid memory
+ * allocation and/or memcpy by the stack.
+ *
+ * This function may not be called in IRQ context. Calls to this function
+ * for a single hardware must be synchronized against each other. Calls to
+ * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
+ * mixed for a single hardware. Must not run concurrently with
+ * ieee80211_tx_status() or ieee80211_tx_status_ni().
+ *
+ * This function must be called with BHs disabled.
*
- * See also netif_napi_add().
+ * @hw: the hardware this frame came in on
+ * @skb: the buffer to receive, owned by mac80211 after this call
+ * @napi: the NAPI context
*/
-void ieee80211_napi_add(struct ieee80211_hw *hw, struct napi_struct *napi,
- struct net_device *napi_dev,
- int (*poll)(struct napi_struct *, int),
- int weight);
+void ieee80211_rx_napi(struct ieee80211_hw *hw, struct sk_buff *skb,
+ struct napi_struct *napi);
/**
* ieee80211_rx - receive frame
@@ -3731,7 +3744,10 @@ void ieee80211_napi_add(struct ieee80211_hw *hw, struct napi_struct *napi,
* @hw: the hardware this frame came in on
* @skb: the buffer to receive, owned by mac80211 after this call
*/
-void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb);
+static inline void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb)
+{
+ ieee80211_rx_napi(hw, skb, NULL);
+}
/**
* ieee80211_rx_irqsafe - receive frame
@@ -4315,19 +4331,6 @@ void ieee80211_get_tkip_p2k(struct ieee80211_key_conf *keyconf,
struct sk_buff *skb, u8 *p2k);
/**
- * ieee80211_aes_cmac_calculate_k1_k2 - calculate the AES-CMAC sub keys
- *
- * This function computes the two AES-CMAC sub-keys, based on the
- * previously installed master key.
- *
- * @keyconf: the parameter passed with the set key
- * @k1: a buffer to be filled with the 1st sub-key
- * @k2: a buffer to be filled with the 2nd sub-key
- */
-void ieee80211_aes_cmac_calculate_k1_k2(struct ieee80211_key_conf *keyconf,
- u8 *k1, u8 *k2);
-
-/**
* ieee80211_get_key_tx_seq - get key TX sequence counter
*
* @keyconf: the parameter passed with the set key