summaryrefslogtreecommitdiffstats
path: root/include/net/mac80211.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/net/mac80211.h')
-rw-r--r--include/net/mac80211.h99
1 files changed, 78 insertions, 21 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index bb86aa6f98dd..82558c8decf8 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -171,6 +171,7 @@ struct ieee80211_low_level_stats {
* @BSS_CHANGED_IDLE: Idle changed for this BSS/interface.
* @BSS_CHANGED_SSID: SSID changed for this BSS (AP mode)
* @BSS_CHANGED_AP_PROBE_RESP: Probe Response changed for this BSS (AP mode)
+ * @BSS_CHANGED_PS: PS changed for this BSS (STA mode)
*/
enum ieee80211_bss_change {
BSS_CHANGED_ASSOC = 1<<0,
@@ -190,6 +191,7 @@ enum ieee80211_bss_change {
BSS_CHANGED_IDLE = 1<<14,
BSS_CHANGED_SSID = 1<<15,
BSS_CHANGED_AP_PROBE_RESP = 1<<16,
+ BSS_CHANGED_PS = 1<<17,
/* when adding here, make sure to change ieee80211_reconfig */
};
@@ -266,6 +268,8 @@ enum ieee80211_rssi_event {
* @idle: This interface is idle. There's also a global idle flag in the
* hardware config which may be more appropriate depending on what
* your driver/device needs to do.
+ * @ps: power-save mode (STA only). This flag is NOT affected by
+ * offchannel/dynamic_ps operations.
* @ssid: The SSID of the current vif. Only valid in AP-mode.
* @ssid_len: Length of SSID given in @ssid.
* @hidden_ssid: The SSID of the current vif is hidden. Only valid in AP-mode.
@@ -296,6 +300,7 @@ struct ieee80211_bss_conf {
bool arp_filter_enabled;
bool qos;
bool idle;
+ bool ps;
u8 ssid[IEEE80211_MAX_SSID_LEN];
size_t ssid_len;
bool hidden_ssid;
@@ -522,9 +527,6 @@ struct ieee80211_tx_rate {
* (2) driver internal use (if applicable)
* (3) TX status information - driver tells mac80211 what happened
*
- * The TX control's sta pointer is only valid during the ->tx call,
- * it may be NULL.
- *
* @flags: transmit info flags, defined above
* @band: the band to transmit on (use for checking for races)
* @hw_queue: HW queue to put the frame on, skb_get_queue_mapping() gives the AC
@@ -555,6 +557,7 @@ struct ieee80211_tx_info {
struct ieee80211_tx_rate rates[
IEEE80211_TX_MAX_RATES];
s8 rts_cts_rate_idx;
+ /* 3 bytes free */
};
/* only needed before rate control */
unsigned long jiffies;
@@ -562,7 +565,7 @@ struct ieee80211_tx_info {
/* NB: vif can be NULL for injected frames */
struct ieee80211_vif *vif;
struct ieee80211_key_conf *hw_key;
- struct ieee80211_sta *sta;
+ /* 8 bytes free */
} control;
struct {
struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
@@ -673,21 +676,41 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
* @RX_FLAG_HT_GF: This frame was received in a HT-greenfield transmission, if
* the driver fills this value it should add %IEEE80211_RADIOTAP_MCS_HAVE_FMT
* to hw.radiotap_mcs_details to advertise that fact
+ * @RX_FLAG_AMPDU_DETAILS: A-MPDU details are known, in particular the reference
+ * number (@ampdu_reference) must be populated and be a distinct number for
+ * each A-MPDU
+ * @RX_FLAG_AMPDU_REPORT_ZEROLEN: driver reports 0-length subframes
+ * @RX_FLAG_AMPDU_IS_ZEROLEN: This is a zero-length subframe, for
+ * monitoring purposes only
+ * @RX_FLAG_AMPDU_LAST_KNOWN: last subframe is known, should be set on all
+ * subframes of a single A-MPDU
+ * @RX_FLAG_AMPDU_IS_LAST: this subframe is the last subframe of the A-MPDU
+ * @RX_FLAG_AMPDU_DELIM_CRC_ERROR: A delimiter CRC error has been detected
+ * on this subframe
+ * @RX_FLAG_AMPDU_DELIM_CRC_KNOWN: The delimiter CRC field is known (the CRC
+ * is stored in the @ampdu_delimiter_crc field)
*/
enum mac80211_rx_flags {
- RX_FLAG_MMIC_ERROR = 1<<0,
- RX_FLAG_DECRYPTED = 1<<1,
- RX_FLAG_MMIC_STRIPPED = 1<<3,
- RX_FLAG_IV_STRIPPED = 1<<4,
- RX_FLAG_FAILED_FCS_CRC = 1<<5,
- RX_FLAG_FAILED_PLCP_CRC = 1<<6,
- RX_FLAG_MACTIME_MPDU = 1<<7,
- RX_FLAG_SHORTPRE = 1<<8,
- RX_FLAG_HT = 1<<9,
- RX_FLAG_40MHZ = 1<<10,
- RX_FLAG_SHORT_GI = 1<<11,
- RX_FLAG_NO_SIGNAL_VAL = 1<<12,
- RX_FLAG_HT_GF = 1<<13,
+ RX_FLAG_MMIC_ERROR = BIT(0),
+ RX_FLAG_DECRYPTED = BIT(1),
+ RX_FLAG_MMIC_STRIPPED = BIT(3),
+ RX_FLAG_IV_STRIPPED = BIT(4),
+ RX_FLAG_FAILED_FCS_CRC = BIT(5),
+ RX_FLAG_FAILED_PLCP_CRC = BIT(6),
+ RX_FLAG_MACTIME_MPDU = BIT(7),
+ RX_FLAG_SHORTPRE = BIT(8),
+ RX_FLAG_HT = BIT(9),
+ RX_FLAG_40MHZ = BIT(10),
+ RX_FLAG_SHORT_GI = BIT(11),
+ RX_FLAG_NO_SIGNAL_VAL = BIT(12),
+ RX_FLAG_HT_GF = BIT(13),
+ RX_FLAG_AMPDU_DETAILS = BIT(14),
+ RX_FLAG_AMPDU_REPORT_ZEROLEN = BIT(15),
+ RX_FLAG_AMPDU_IS_ZEROLEN = BIT(16),
+ RX_FLAG_AMPDU_LAST_KNOWN = BIT(17),
+ RX_FLAG_AMPDU_IS_LAST = BIT(18),
+ RX_FLAG_AMPDU_DELIM_CRC_ERROR = BIT(19),
+ RX_FLAG_AMPDU_DELIM_CRC_KNOWN = BIT(20),
};
/**
@@ -711,17 +734,22 @@ enum mac80211_rx_flags {
* HT rates are use (RX_FLAG_HT)
* @flag: %RX_FLAG_*
* @rx_flags: internal RX flags for mac80211
+ * @ampdu_reference: A-MPDU reference number, must be a different value for
+ * each A-MPDU but the same for each subframe within one A-MPDU
+ * @ampdu_delimiter_crc: A-MPDU delimiter CRC
*/
struct ieee80211_rx_status {
u64 mactime;
u32 device_timestamp;
- u16 flag;
+ u32 ampdu_reference;
+ u32 flag;
u16 freq;
u8 rate_idx;
u8 rx_flags;
u8 band;
u8 antenna;
s8 signal;
+ u8 ampdu_delimiter_crc;
};
/**
@@ -945,21 +973,29 @@ static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
* generation in software.
* @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
* that the key is pairwise rather then a shared key.
- * @IEEE80211_KEY_FLAG_SW_MGMT: This flag should be set by the driver for a
+ * @IEEE80211_KEY_FLAG_SW_MGMT_TX: This flag should be set by the driver for a
* CCMP key if it requires CCMP encryption of management frames (MFP) to
* be done in software.
* @IEEE80211_KEY_FLAG_PUT_IV_SPACE: This flag should be set by the driver
* if space should be prepared for the IV, but the IV
* itself should not be generated. Do not set together with
* @IEEE80211_KEY_FLAG_GENERATE_IV on the same key.
+ * @IEEE80211_KEY_FLAG_RX_MGMT: This key will be used to decrypt received
+ * management frames. The flag can help drivers that have a hardware
+ * crypto implementation that doesn't deal with management frames
+ * properly by allowing them to not upload the keys to hardware and
+ * fall back to software crypto. Note that this flag deals only with
+ * RX, if your crypto engine can't deal with TX you can also set the
+ * %IEEE80211_KEY_FLAG_SW_MGMT_TX flag to encrypt such frames in SW.
*/
enum ieee80211_key_flags {
IEEE80211_KEY_FLAG_WMM_STA = 1<<0,
IEEE80211_KEY_FLAG_GENERATE_IV = 1<<1,
IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2,
IEEE80211_KEY_FLAG_PAIRWISE = 1<<3,
- IEEE80211_KEY_FLAG_SW_MGMT = 1<<4,
+ IEEE80211_KEY_FLAG_SW_MGMT_TX = 1<<4,
IEEE80211_KEY_FLAG_PUT_IV_SPACE = 1<<5,
+ IEEE80211_KEY_FLAG_RX_MGMT = 1<<6,
};
/**
@@ -1074,6 +1110,16 @@ enum sta_notify_cmd {
};
/**
+ * struct ieee80211_tx_control - TX control data
+ *
+ * @sta: station table entry, this sta pointer may be NULL and
+ * it is not allowed to copy the pointer, due to RCU.
+ */
+struct ieee80211_tx_control {
+ struct ieee80211_sta *sta;
+};
+
+/**
* enum ieee80211_hw_flags - hardware flags
*
* These flags are used to indicate hardware capabilities to
@@ -1203,6 +1249,10 @@ enum sta_notify_cmd {
* queue mapping in order to use different queues (not just one per AC)
* for different virtual interfaces. See the doc section on HW queue
* control for more details.
+ *
+ * @IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF: Use the P2P Device address for any
+ * P2P Interface. This will be honoured even if more than one interface
+ * is supported.
*/
enum ieee80211_hw_flags {
IEEE80211_HW_HAS_RATE_CONTROL = 1<<0,
@@ -1230,6 +1280,7 @@ enum ieee80211_hw_flags {
IEEE80211_HW_AP_LINK_PS = 1<<22,
IEEE80211_HW_TX_AMPDU_SETUP_IN_HW = 1<<23,
IEEE80211_HW_SCAN_WHILE_IDLE = 1<<24,
+ IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF = 1<<25,
};
/**
@@ -1884,10 +1935,14 @@ enum ieee80211_frame_release_type {
* @IEEE80211_RC_BW_CHANGED: The bandwidth that can be used to transmit
* to this station changed.
* @IEEE80211_RC_SMPS_CHANGED: The SMPS state of the station changed.
+ * @IEEE80211_RC_SUPP_RATES_CHANGED: The supported rate set of this peer
+ * changed (in IBSS mode) due to discovering more information about
+ * the peer.
*/
enum ieee80211_rate_control_changed {
IEEE80211_RC_BW_CHANGED = BIT(0),
IEEE80211_RC_SMPS_CHANGED = BIT(1),
+ IEEE80211_RC_SUPP_RATES_CHANGED = BIT(2),
};
/**
@@ -2264,7 +2319,9 @@ enum ieee80211_rate_control_changed {
* The callback is optional and can (should!) sleep.
*/
struct ieee80211_ops {
- void (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb);
+ void (*tx)(struct ieee80211_hw *hw,
+ struct ieee80211_tx_control *control,
+ struct sk_buff *skb);
int (*start)(struct ieee80211_hw *hw);
void (*stop)(struct ieee80211_hw *hw);
#ifdef CONFIG_PM