diff options
Diffstat (limited to 'include/media/v4l2-subdev.h')
| -rw-r--r-- | include/media/v4l2-subdev.h | 54 |
1 files changed, 38 insertions, 16 deletions
diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h index 02c6f4d11ed3..4a97d7341a94 100644 --- a/include/media/v4l2-subdev.h +++ b/include/media/v4l2-subdev.h @@ -35,6 +35,7 @@ #define V4L2_SUBDEV_IR_TX_FIFO_SERVICE_REQ 0x00000001 struct v4l2_device; +struct v4l2_ctrl_handler; struct v4l2_subdev; struct tuner_setup; @@ -90,10 +91,31 @@ struct v4l2_decode_vbi_line { not yet implemented) since ops provide proper type-checking. */ +/* Subdevice external IO pin configuration */ +#define V4L2_SUBDEV_IO_PIN_DISABLE (1 << 0) /* ENABLE assumed */ +#define V4L2_SUBDEV_IO_PIN_OUTPUT (1 << 1) +#define V4L2_SUBDEV_IO_PIN_INPUT (1 << 2) +#define V4L2_SUBDEV_IO_PIN_SET_VALUE (1 << 3) /* Set output value */ +#define V4L2_SUBDEV_IO_PIN_ACTIVE_LOW (1 << 4) /* ACTIVE HIGH assumed */ + +struct v4l2_subdev_io_pin_config { + u32 flags; /* V4L2_SUBDEV_IO_PIN_* flags for this pin's config */ + u8 pin; /* Chip external IO pin to configure */ + u8 function; /* Internal signal pad/function to route to IO pin */ + u8 value; /* Initial value for pin - e.g. GPIO output value */ + u8 strength; /* Pin drive strength */ +}; + /* s_config: if set, then it is always called by the v4l2_i2c_new_subdev* functions after the v4l2_subdev was registered. It is used to pass platform data to the subdev which can be used during initialization. + s_io_pin_config: configure one or more chip I/O pins for chips that + multiplex different internal signal pads out to IO pins. This function + takes a pointer to an array of 'n' pin configuration entries, one for + each pin being configured. This function could be called at times + other than just subdevice initialization. + init: initialize the sensor registors to some sort of reasonable default values. Do not use for new drivers and should be removed in existing drivers. @@ -110,11 +132,18 @@ struct v4l2_decode_vbi_line { s_power: puts subdevice in power saving mode (on == 0) or normal operation mode (on == 1). + + interrupt_service_routine: Called by the bridge chip's interrupt service + handler, when an interrupt status has be raised due to this subdev, + so that this subdev can handle the details. It may schedule work to be + performed later. It must not sleep. *Called from an IRQ context*. */ struct v4l2_subdev_core_ops { int (*g_chip_ident)(struct v4l2_subdev *sd, struct v4l2_dbg_chip_ident *chip); int (*log_status)(struct v4l2_subdev *sd); int (*s_config)(struct v4l2_subdev *sd, int irq, void *platform_data); + int (*s_io_pin_config)(struct v4l2_subdev *sd, size_t n, + struct v4l2_subdev_io_pin_config *pincfg); int (*init)(struct v4l2_subdev *sd, u32 val); int (*load_fw)(struct v4l2_subdev *sd); int (*reset)(struct v4l2_subdev *sd, u32 val); @@ -133,6 +162,8 @@ struct v4l2_subdev_core_ops { int (*s_register)(struct v4l2_subdev *sd, struct v4l2_dbg_register *reg); #endif int (*s_power)(struct v4l2_subdev *sd, int on); + int (*interrupt_service_routine)(struct v4l2_subdev *sd, + u32 status, bool *handled); }; /* s_mode: switch the tuner to a specific tuner mode. Replacement of s_radio. @@ -307,11 +338,6 @@ struct v4l2_subdev_sensor_ops { }; /* - interrupt_service_routine: Called by the bridge chip's interrupt service - handler, when an IR interrupt status has be raised due to this subdev, - so that this subdev can handle the details. It may schedule work to be - performed later. It must not sleep. *Called from an IRQ context*. - [rt]x_g_parameters: Get the current operating parameters and state of the the IR receiver or transmitter. @@ -335,14 +361,9 @@ struct v4l2_subdev_sensor_ops { */ enum v4l2_subdev_ir_mode { - V4L2_SUBDEV_IR_MODE_PULSE_WIDTH, /* space & mark widths in nanosecs */ + V4L2_SUBDEV_IR_MODE_PULSE_WIDTH, /* uses struct ir_raw_event records */ }; -/* Data format of data read or written for V4L2_SUBDEV_IR_MODE_PULSE_WIDTH */ -#define V4L2_SUBDEV_IR_PULSE_MAX_WIDTH_NS 0x7fffffff -#define V4L2_SUBDEV_IR_PULSE_LEVEL_MASK 0x80000000 -#define V4L2_SUBDEV_IR_PULSE_RX_SEQ_END 0xffffffff - struct v4l2_subdev_ir_parameters { /* Either Rx or Tx */ unsigned int bytes_per_data_element; /* of data in read or write call */ @@ -356,7 +377,10 @@ struct v4l2_subdev_ir_parameters { u32 max_pulse_width; /* ns, valid only for baseband signal */ unsigned int carrier_freq; /* Hz, valid only for modulated signal*/ unsigned int duty_cycle; /* percent, valid only for modulated signal*/ - bool invert; /* logically invert sense of mark/space */ + bool invert_level; /* invert signal level */ + + /* Tx only */ + bool invert_carrier_sense; /* Send 0/space as a carrier burst */ /* Rx only */ u32 noise_filter_min_width; /* ns, min time of a valid pulse */ @@ -366,10 +390,6 @@ struct v4l2_subdev_ir_parameters { }; struct v4l2_subdev_ir_ops { - /* Common to receiver and transmitter */ - int (*interrupt_service_routine)(struct v4l2_subdev *sd, - u32 status, bool *handled); - /* Receiver */ int (*rx_read)(struct v4l2_subdev *sd, u8 *buf, size_t count, ssize_t *num); @@ -415,6 +435,8 @@ struct v4l2_subdev { u32 flags; struct v4l2_device *v4l2_dev; const struct v4l2_subdev_ops *ops; + /* The control handler of this subdev. May be NULL. */ + struct v4l2_ctrl_handler *ctrl_handler; /* name must be unique */ char name[V4L2_SUBDEV_NAME_SIZE]; /* can be used to group similar subdevs, value is driver-specific */ |