diff options
Diffstat (limited to 'include/linux/mfd')
| -rw-r--r-- | include/linux/mfd/dm355evm_msp.h | 79 | ||||
| -rw-r--r-- | include/linux/mfd/max8997.h | 3 | ||||
| -rw-r--r-- | include/linux/mfd/palmas.h | 1 | ||||
| -rw-r--r-- | include/linux/mfd/pcf50633/core.h | 6 | ||||
| -rw-r--r-- | include/linux/mfd/rn5t618.h | 9 | ||||
| -rw-r--r-- | include/linux/mfd/stmfx.h | 2 | ||||
| -rw-r--r-- | include/linux/mfd/tmio.h | 1 | ||||
| -rw-r--r-- | include/linux/mfd/tps65219.h | 345 | ||||
| -rw-r--r-- | include/linux/mfd/twl6040.h | 32 |
9 files changed, 358 insertions, 120 deletions
diff --git a/include/linux/mfd/dm355evm_msp.h b/include/linux/mfd/dm355evm_msp.h deleted file mode 100644 index 372470350fab..000000000000 --- a/include/linux/mfd/dm355evm_msp.h +++ /dev/null @@ -1,79 +0,0 @@ -/* - * dm355evm_msp.h - support MSP430 microcontroller on DM355EVM board - */ -#ifndef __LINUX_I2C_DM355EVM_MSP -#define __LINUX_I2C_DM355EVM_MSP - -/* - * Written against Spectrum's writeup for the A4 firmware revision, - * and tweaked to match source and rev D2 schematics by removing CPLD - * and NOR flash hooks (which were last appropriate in rev B boards). - * - * Note that the firmware supports a flavor of write posting ... to be - * sure a write completes, issue another read or write. - */ - -/* utilities to access "registers" emulated by msp430 firmware */ -extern int dm355evm_msp_write(u8 value, u8 reg); -extern int dm355evm_msp_read(u8 reg); - - -/* command/control registers */ -#define DM355EVM_MSP_COMMAND 0x00 -# define MSP_COMMAND_NULL 0 -# define MSP_COMMAND_RESET_COLD 1 -# define MSP_COMMAND_RESET_WARM 2 -# define MSP_COMMAND_RESET_WARM_I 3 -# define MSP_COMMAND_POWEROFF 4 -# define MSP_COMMAND_IR_REINIT 5 -#define DM355EVM_MSP_STATUS 0x01 -# define MSP_STATUS_BAD_OFFSET BIT(0) -# define MSP_STATUS_BAD_COMMAND BIT(1) -# define MSP_STATUS_POWER_ERROR BIT(2) -# define MSP_STATUS_RXBUF_OVERRUN BIT(3) -#define DM355EVM_MSP_RESET 0x02 /* 0 bits == in reset */ -# define MSP_RESET_DC5 BIT(0) -# define MSP_RESET_TVP5154 BIT(2) -# define MSP_RESET_IMAGER BIT(3) -# define MSP_RESET_ETHERNET BIT(4) -# define MSP_RESET_SYS BIT(5) -# define MSP_RESET_AIC33 BIT(7) - -/* GPIO registers ... bit patterns mostly match the source MSP ports */ -#define DM355EVM_MSP_LED 0x03 /* active low (MSP P4) */ -#define DM355EVM_MSP_SWITCH1 0x04 /* (MSP P5, masked) */ -# define MSP_SWITCH1_SW6_1 BIT(0) -# define MSP_SWITCH1_SW6_2 BIT(1) -# define MSP_SWITCH1_SW6_3 BIT(2) -# define MSP_SWITCH1_SW6_4 BIT(3) -# define MSP_SWITCH1_J1 BIT(4) /* NTSC/PAL */ -# define MSP_SWITCH1_MSP_INT BIT(5) /* active low */ -#define DM355EVM_MSP_SWITCH2 0x05 /* (MSP P6, masked) */ -# define MSP_SWITCH2_SW10 BIT(3) -# define MSP_SWITCH2_SW11 BIT(4) -# define MSP_SWITCH2_SW12 BIT(5) -# define MSP_SWITCH2_SW13 BIT(6) -# define MSP_SWITCH2_SW14 BIT(7) -#define DM355EVM_MSP_SDMMC 0x06 /* (MSP P2, masked) */ -# define MSP_SDMMC_0_WP BIT(1) -# define MSP_SDMMC_0_CD BIT(2) /* active low */ -# define MSP_SDMMC_1_WP BIT(3) -# define MSP_SDMMC_1_CD BIT(4) /* active low */ -#define DM355EVM_MSP_FIRMREV 0x07 /* not a GPIO (out of order) */ -#define DM355EVM_MSP_VIDEO_IN 0x08 /* (MSP P3, masked) */ -# define MSP_VIDEO_IMAGER BIT(7) /* low == tvp5146 */ - -/* power supply registers are currently omitted */ - -/* RTC registers */ -#define DM355EVM_MSP_RTC_0 0x12 /* LSB */ -#define DM355EVM_MSP_RTC_1 0x13 -#define DM355EVM_MSP_RTC_2 0x14 -#define DM355EVM_MSP_RTC_3 0x15 /* MSB */ - -/* input event queue registers; code == ((HIGH << 8) | LOW) */ -#define DM355EVM_MSP_INPUT_COUNT 0x16 /* decrement by reading LOW */ -#define DM355EVM_MSP_INPUT_HIGH 0x17 -#define DM355EVM_MSP_INPUT_LOW 0x18 - -#endif /* __LINUX_I2C_DM355EVM_MSP */ diff --git a/include/linux/mfd/max8997.h b/include/linux/mfd/max8997.h index 6c98edcf4b0b..6193905abbb5 100644 --- a/include/linux/mfd/max8997.h +++ b/include/linux/mfd/max8997.h @@ -110,8 +110,6 @@ enum max8997_haptic_pwm_divisor { /** * max8997_haptic_platform_data - * @pwm_channel_id: channel number of PWM device - * valid for MAX8997_EXTERNAL_MODE * @pwm_period: period in nano second for PWM device * valid for MAX8997_EXTERNAL_MODE * @type: motor type @@ -128,7 +126,6 @@ enum max8997_haptic_pwm_divisor { * [0 - 255]: available period */ struct max8997_haptic_platform_data { - unsigned int pwm_channel_id; unsigned int pwm_period; enum max8997_haptic_motor_type type; diff --git a/include/linux/mfd/palmas.h b/include/linux/mfd/palmas.h index 1e61c7e9f50d..117d02708439 100644 --- a/include/linux/mfd/palmas.h +++ b/include/linux/mfd/palmas.h @@ -16,7 +16,6 @@ #include <linux/regmap.h> #include <linux/regulator/driver.h> #include <linux/extcon-provider.h> -#include <linux/of_gpio.h> #include <linux/usb/phy_companion.h> #define PALMAS_NUM_CLIENTS 3 diff --git a/include/linux/mfd/pcf50633/core.h b/include/linux/mfd/pcf50633/core.h index 3f752dc62a6c..539f27f8bd89 100644 --- a/include/linux/mfd/pcf50633/core.h +++ b/include/linux/mfd/pcf50633/core.h @@ -13,6 +13,7 @@ #include <linux/workqueue.h> #include <linux/regulator/driver.h> #include <linux/regulator/machine.h> +#include <linux/pm.h> #include <linux/power_supply.h> #include <linux/mfd/pcf50633/backlight.h> @@ -226,9 +227,6 @@ static inline struct pcf50633 *dev_to_pcf50633(struct device *dev) int pcf50633_irq_init(struct pcf50633 *pcf, int irq); void pcf50633_irq_free(struct pcf50633 *pcf); -#ifdef CONFIG_PM -int pcf50633_irq_suspend(struct pcf50633 *pcf); -int pcf50633_irq_resume(struct pcf50633 *pcf); -#endif +extern const struct dev_pm_ops pcf50633_pm; #endif diff --git a/include/linux/mfd/rn5t618.h b/include/linux/mfd/rn5t618.h index 8aa0bda1af4f..aacb6d51e99c 100644 --- a/include/linux/mfd/rn5t618.h +++ b/include/linux/mfd/rn5t618.h @@ -227,6 +227,15 @@ #define RN5T618_WATCHDOG_WDOGTIM_S 0 #define RN5T618_PWRIRQ_IR_WDOG BIT(6) +#define RN5T618_POFFHIS_PWRON BIT(0) +#define RN5T618_POFFHIS_TSHUT BIT(1) +#define RN5T618_POFFHIS_VINDET BIT(2) +#define RN5T618_POFFHIS_IODET BIT(3) +#define RN5T618_POFFHIS_CPU BIT(4) +#define RN5T618_POFFHIS_WDG BIT(5) +#define RN5T618_POFFHIS_DCLIM BIT(6) +#define RN5T618_POFFHIS_N_OE BIT(7) + enum { RN5T618_DCDC1, RN5T618_DCDC2, diff --git a/include/linux/mfd/stmfx.h b/include/linux/mfd/stmfx.h index 744dce63946e..967a2e486800 100644 --- a/include/linux/mfd/stmfx.h +++ b/include/linux/mfd/stmfx.h @@ -113,10 +113,8 @@ struct stmfx { struct irq_domain *irq_domain; struct mutex lock; /* IRQ bus lock */ u8 irq_src; -#ifdef CONFIG_PM u8 bkp_sysctrl; u8 bkp_irqoutpin; -#endif }; int stmfx_function_enable(struct stmfx *stmfx, u32 func); diff --git a/include/linux/mfd/tmio.h b/include/linux/mfd/tmio.h index 27264fe4b3b9..e8bf90281ba0 100644 --- a/include/linux/mfd/tmio.h +++ b/include/linux/mfd/tmio.h @@ -102,7 +102,6 @@ struct tmio_mmc_data { unsigned long capabilities2; unsigned long flags; u32 ocr_mask; /* available voltages */ - int alignment_shift; dma_addr_t dma_rx_offset; unsigned int max_blk_count; unsigned short max_segs; diff --git a/include/linux/mfd/tps65219.h b/include/linux/mfd/tps65219.h new file mode 100644 index 000000000000..e6826e34e2a6 --- /dev/null +++ b/include/linux/mfd/tps65219.h @@ -0,0 +1,345 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Functions to access TPS65219 Power Management IC. + * + * Copyright (C) 2022 BayLibre Incorporated - https://www.baylibre.com/ + */ + +#ifndef MFD_TPS65219_H +#define MFD_TPS65219_H + +#include <linux/bitops.h> +#include <linux/notifier.h> +#include <linux/regulator/driver.h> + +struct regmap; +struct regmap_irq_chip_data; + +#define TPS65219_1V35 1350000 +#define TPS65219_1V8 1800000 + +/* TPS chip id list */ +#define TPS65219 0xF0 + +/* I2C ID for TPS65219 part */ +#define TPS65219_I2C_ID 0x24 + +/* All register addresses */ +#define TPS65219_REG_TI_DEV_ID 0x00 +#define TPS65219_REG_NVM_ID 0x01 +#define TPS65219_REG_ENABLE_CTRL 0x02 +#define TPS65219_REG_BUCKS_CONFIG 0x03 +#define TPS65219_REG_LDO4_VOUT 0x04 +#define TPS65219_REG_LDO3_VOUT 0x05 +#define TPS65219_REG_LDO2_VOUT 0x06 +#define TPS65219_REG_LDO1_VOUT 0x07 +#define TPS65219_REG_BUCK3_VOUT 0x8 +#define TPS65219_REG_BUCK2_VOUT 0x9 +#define TPS65219_REG_BUCK1_VOUT 0xA +#define TPS65219_REG_LDO4_SEQUENCE_SLOT 0xB +#define TPS65219_REG_LDO3_SEQUENCE_SLOT 0xC +#define TPS65219_REG_LDO2_SEQUENCE_SLOT 0xD +#define TPS65219_REG_LDO1_SEQUENCE_SLOT 0xE +#define TPS65219_REG_BUCK3_SEQUENCE_SLOT 0xF +#define TPS65219_REG_BUCK2_SEQUENCE_SLOT 0x10 +#define TPS65219_REG_BUCK1_SEQUENCE_SLOT 0x11 +#define TPS65219_REG_nRST_SEQUENCE_SLOT 0x12 +#define TPS65219_REG_GPIO_SEQUENCE_SLOT 0x13 +#define TPS65219_REG_GPO2_SEQUENCE_SLOT 0x14 +#define TPS65219_REG_GPO1_SEQUENCE_SLOT 0x15 +#define TPS65219_REG_POWER_UP_SLOT_DURATION_1 0x16 +#define TPS65219_REG_POWER_UP_SLOT_DURATION_2 0x17 +#define TPS65219_REG_POWER_UP_SLOT_DURATION_3 0x18 +#define TPS65219_REG_POWER_UP_SLOT_DURATION_4 0x19 +#define TPS65219_REG_POWER_DOWN_SLOT_DURATION_1 0x1A +#define TPS65219_REG_POWER_DOWN_SLOT_DURATION_2 0x1B +#define TPS65219_REG_POWER_DOWN_SLOT_DURATION_3 0x1C +#define TPS65219_REG_POWER_DOWN_SLOT_DURATION_4 0x1D +#define TPS65219_REG_GENERAL_CONFIG 0x1E +#define TPS65219_REG_MFP_1_CONFIG 0x1F +#define TPS65219_REG_MFP_2_CONFIG 0x20 +#define TPS65219_REG_STBY_1_CONFIG 0x21 +#define TPS65219_REG_STBY_2_CONFIG 0x22 +#define TPS65219_REG_OC_DEGL_CONFIG 0x23 +/* 'sub irq' MASK registers */ +#define TPS65219_REG_INT_MASK_UV 0x24 +#define TPS65219_REG_MASK_CONFIG 0x25 + +#define TPS65219_REG_I2C_ADDRESS_REG 0x26 +#define TPS65219_REG_USER_GENERAL_NVM_STORAGE 0x27 +#define TPS65219_REG_MANUFACTURING_VER 0x28 +#define TPS65219_REG_MFP_CTRL 0x29 +#define TPS65219_REG_DISCHARGE_CONFIG 0x2A +/* main irq registers */ +#define TPS65219_REG_INT_SOURCE 0x2B +/* 'sub irq' registers */ +#define TPS65219_REG_INT_LDO_3_4 0x2C +#define TPS65219_REG_INT_LDO_1_2 0x2D +#define TPS65219_REG_INT_BUCK_3 0x2E +#define TPS65219_REG_INT_BUCK_1_2 0x2F +#define TPS65219_REG_INT_SYSTEM 0x30 +#define TPS65219_REG_INT_RV 0x31 +#define TPS65219_REG_INT_TIMEOUT_RV_SD 0x32 +#define TPS65219_REG_INT_PB 0x33 + +#define TPS65219_REG_INT_LDO_3_4_POS 0 +#define TPS65219_REG_INT_LDO_1_2_POS 1 +#define TPS65219_REG_INT_BUCK_3_POS 2 +#define TPS65219_REG_INT_BUCK_1_2_POS 3 +#define TPS65219_REG_INT_SYS_POS 4 +#define TPS65219_REG_INT_RV_POS 5 +#define TPS65219_REG_INT_TO_RV_POS 6 +#define TPS65219_REG_INT_PB_POS 7 + +#define TPS65219_REG_USER_NVM_CMD 0x34 +#define TPS65219_REG_POWER_UP_STATUS 0x35 +#define TPS65219_REG_SPARE_2 0x36 +#define TPS65219_REG_SPARE_3 0x37 +#define TPS65219_REG_FACTORY_CONFIG_2 0x41 + +/* Register field definitions */ +#define TPS65219_DEVID_REV_MASK GENMASK(7, 0) +#define TPS65219_BUCKS_LDOS_VOUT_VSET_MASK GENMASK(5, 0) +#define TPS65219_BUCKS_UV_THR_SEL_MASK BIT(6) +#define TPS65219_BUCKS_BW_SEL_MASK BIT(7) +#define LDO_BYP_SHIFT 6 +#define TPS65219_LDOS_BYP_CONFIG_MASK BIT(LDO_BYP_SHIFT) +#define TPS65219_LDOS_LSW_CONFIG_MASK BIT(7) +/* Regulators enable control */ +#define TPS65219_ENABLE_BUCK1_EN_MASK BIT(0) +#define TPS65219_ENABLE_BUCK2_EN_MASK BIT(1) +#define TPS65219_ENABLE_BUCK3_EN_MASK BIT(2) +#define TPS65219_ENABLE_LDO1_EN_MASK BIT(3) +#define TPS65219_ENABLE_LDO2_EN_MASK BIT(4) +#define TPS65219_ENABLE_LDO3_EN_MASK BIT(5) +#define TPS65219_ENABLE_LDO4_EN_MASK BIT(6) +/* power ON-OFF sequence slot */ +#define TPS65219_BUCKS_LDOS_SEQUENCE_OFF_SLOT_MASK GENMASK(3, 0) +#define TPS65219_BUCKS_LDOS_SEQUENCE_ON_SLOT_MASK GENMASK(7, 4) +/* TODO: Not needed, same mapping as TPS65219_ENABLE_REGNAME_EN, factorize */ +#define TPS65219_STBY1_BUCK1_STBY_EN_MASK BIT(0) +#define TPS65219_STBY1_BUCK2_STBY_EN_MASK BIT(1) +#define TPS65219_STBY1_BUCK3_STBY_EN_MASK BIT(2) +#define TPS65219_STBY1_LDO1_STBY_EN_MASK BIT(3) +#define TPS65219_STBY1_LDO2_STBY_EN_MASK BIT(4) +#define TPS65219_STBY1_LDO3_STBY_EN_MASK BIT(5) +#define TPS65219_STBY1_LDO4_STBY_EN_MASK BIT(6) +/* STBY_2 config */ +#define TPS65219_STBY2_GPO1_STBY_EN_MASK BIT(0) +#define TPS65219_STBY2_GPO2_STBY_EN_MASK BIT(1) +#define TPS65219_STBY2_GPIO_STBY_EN_MASK BIT(2) +/* MFP Control */ +#define TPS65219_MFP_I2C_OFF_REQ_MASK BIT(0) +#define TPS65219_MFP_STBY_I2C_CTRL_MASK BIT(1) +#define TPS65219_MFP_COLD_RESET_I2C_CTRL_MASK BIT(2) +#define TPS65219_MFP_WARM_RESET_I2C_CTRL_MASK BIT(3) +#define TPS65219_MFP_GPIO_STATUS_MASK BIT(4) +/* MFP_1 Config */ +#define TPS65219_MFP_1_VSEL_DDR_SEL_MASK BIT(0) +#define TPS65219_MFP_1_VSEL_SD_POL_MASK BIT(1) +#define TPS65219_MFP_1_VSEL_RAIL_MASK BIT(2) +/* MFP_2 Config */ +#define TPS65219_MFP_2_MODE_STBY_MASK GENMASK(1, 0) +#define TPS65219_MFP_2_MODE_RESET_MASK BIT(2) +#define TPS65219_MFP_2_EN_PB_VSENSE_DEGL_MASK BIT(3) +#define TPS65219_MFP_2_EN_PB_VSENSE_MASK GENMASK(5, 4) +#define TPS65219_MFP_2_WARM_COLD_RESET_MASK BIT(6) +#define TPS65219_MFP_2_PU_ON_FSD_MASK BIT(7) +#define TPS65219_MFP_2_EN 0 +#define TPS65219_MFP_2_PB BIT(4) +#define TPS65219_MFP_2_VSENSE BIT(5) +/* MASK_UV Config */ +#define TPS65219_REG_MASK_UV_LDO1_UV_MASK BIT(0) +#define TPS65219_REG_MASK_UV_LDO2_UV_MASK BIT(1) +#define TPS65219_REG_MASK_UV_LDO3_UV_MASK BIT(2) +#define TPS65219_REG_MASK_UV_LDO4_UV_MASK BIT(3) +#define TPS65219_REG_MASK_UV_BUCK1_UV_MASK BIT(4) +#define TPS65219_REG_MASK_UV_BUCK2_UV_MASK BIT(5) +#define TPS65219_REG_MASK_UV_BUCK3_UV_MASK BIT(6) +#define TPS65219_REG_MASK_UV_RETRY_MASK BIT(7) +/* MASK Config */ +// SENSOR_N_WARM_MASK already defined in Thermal +#define TPS65219_REG_MASK_INT_FOR_RV_MASK BIT(4) +#define TPS65219_REG_MASK_EFFECT_MASK GENMASK(2, 1) +#define TPS65219_REG_MASK_INT_FOR_PB_MASK BIT(7) +/* UnderVoltage - Short to GND - OverCurrent*/ +/* LDO3-4 */ +#define TPS65219_INT_LDO3_SCG_MASK BIT(0) +#define TPS65219_INT_LDO3_OC_MASK BIT(1) +#define TPS65219_INT_LDO3_UV_MASK BIT(2) +#define TPS65219_INT_LDO4_SCG_MASK BIT(3) +#define TPS65219_INT_LDO4_OC_MASK BIT(4) +#define TPS65219_INT_LDO4_UV_MASK BIT(5) +/* LDO1-2 */ +#define TPS65219_INT_LDO1_SCG_MASK BIT(0) +#define TPS65219_INT_LDO1_OC_MASK BIT(1) +#define TPS65219_INT_LDO1_UV_MASK BIT(2) +#define TPS65219_INT_LDO2_SCG_MASK BIT(3) +#define TPS65219_INT_LDO2_OC_MASK BIT(4) +#define TPS65219_INT_LDO2_UV_MASK BIT(5) +/* BUCK3 */ +#define TPS65219_INT_BUCK3_SCG_MASK BIT(0) +#define TPS65219_INT_BUCK3_OC_MASK BIT(1) +#define TPS65219_INT_BUCK3_NEG_OC_MASK BIT(2) +#define TPS65219_INT_BUCK3_UV_MASK BIT(3) +/* BUCK1-2 */ +#define TPS65219_INT_BUCK1_SCG_MASK BIT(0) +#define TPS65219_INT_BUCK1_OC_MASK BIT(1) +#define TPS65219_INT_BUCK1_NEG_OC_MASK BIT(2) +#define TPS65219_INT_BUCK1_UV_MASK BIT(3) +#define TPS65219_INT_BUCK2_SCG_MASK BIT(4) +#define TPS65219_INT_BUCK2_OC_MASK BIT(5) +#define TPS65219_INT_BUCK2_NEG_OC_MASK BIT(6) +#define TPS65219_INT_BUCK2_UV_MASK BIT(7) +/* Thermal Sensor */ +#define TPS65219_INT_SENSOR_3_WARM_MASK BIT(0) +#define TPS65219_INT_SENSOR_2_WARM_MASK BIT(1) +#define TPS65219_INT_SENSOR_1_WARM_MASK BIT(2) +#define TPS65219_INT_SENSOR_0_WARM_MASK BIT(3) +#define TPS65219_INT_SENSOR_3_HOT_MASK BIT(4) +#define TPS65219_INT_SENSOR_2_HOT_MASK BIT(5) +#define TPS65219_INT_SENSOR_1_HOT_MASK BIT(6) +#define TPS65219_INT_SENSOR_0_HOT_MASK BIT(7) +/* Residual Voltage */ +#define TPS65219_INT_BUCK1_RV_MASK BIT(0) +#define TPS65219_INT_BUCK2_RV_MASK BIT(1) +#define TPS65219_INT_BUCK3_RV_MASK BIT(2) +#define TPS65219_INT_LDO1_RV_MASK BIT(3) +#define TPS65219_INT_LDO2_RV_MASK BIT(4) +#define TPS65219_INT_LDO3_RV_MASK BIT(5) +#define TPS65219_INT_LDO4_RV_MASK BIT(6) +/* Residual Voltage ShutDown */ +#define TPS65219_INT_BUCK1_RV_SD_MASK BIT(0) +#define TPS65219_INT_BUCK2_RV_SD_MASK BIT(1) +#define TPS65219_INT_BUCK3_RV_SD_MASK BIT(2) +#define TPS65219_INT_LDO1_RV_SD_MASK BIT(3) +#define TPS65219_INT_LDO2_RV_SD_MASK BIT(4) +#define TPS65219_INT_LDO3_RV_SD_MASK BIT(5) +#define TPS65219_INT_LDO4_RV_SD_MASK BIT(6) +#define TPS65219_INT_TIMEOUT_MASK BIT(7) +/* Power Button */ +#define TPS65219_INT_PB_FALLING_EDGE_DETECT_MASK BIT(0) +#define TPS65219_INT_PB_RISING_EDGE_DETECT_MASK BIT(1) +#define TPS65219_INT_PB_REAL_TIME_STATUS_MASK BIT(2) + +#define TPS65219_PB_POS 7 +#define TPS65219_TO_RV_POS 6 +#define TPS65219_RV_POS 5 +#define TPS65219_SYS_POS 4 +#define TPS65219_BUCK_1_2_POS 3 +#define TPS65219_BUCK_3_POS 2 +#define TPS65219_LDO_1_2_POS 1 +#define TPS65219_LDO_3_4_POS 0 + +/* IRQs */ +enum { + /* LDO3-4 register IRQs */ + TPS65219_INT_LDO3_SCG, + TPS65219_INT_LDO3_OC, + TPS65219_INT_LDO3_UV, + TPS65219_INT_LDO4_SCG, + TPS65219_INT_LDO4_OC, + TPS65219_INT_LDO4_UV, + /* LDO1-2 */ + TPS65219_INT_LDO1_SCG, + TPS65219_INT_LDO1_OC, + TPS65219_INT_LDO1_UV, + TPS65219_INT_LDO2_SCG, + TPS65219_INT_LDO2_OC, + TPS65219_INT_LDO2_UV, + /* BUCK3 */ + TPS65219_INT_BUCK3_SCG, + TPS65219_INT_BUCK3_OC, + TPS65219_INT_BUCK3_NEG_OC, + TPS65219_INT_BUCK3_UV, + /* BUCK1-2 */ + TPS65219_INT_BUCK1_SCG, + TPS65219_INT_BUCK1_OC, + TPS65219_INT_BUCK1_NEG_OC, + TPS65219_INT_BUCK1_UV, + TPS65219_INT_BUCK2_SCG, + TPS65219_INT_BUCK2_OC, + TPS65219_INT_BUCK2_NEG_OC, + TPS65219_INT_BUCK2_UV, + /* Thermal Sensor */ + TPS65219_INT_SENSOR_3_WARM, + TPS65219_INT_SENSOR_2_WARM, + TPS65219_INT_SENSOR_1_WARM, + TPS65219_INT_SENSOR_0_WARM, + TPS65219_INT_SENSOR_3_HOT, + TPS65219_INT_SENSOR_2_HOT, + TPS65219_INT_SENSOR_1_HOT, + TPS65219_INT_SENSOR_0_HOT, + /* Residual Voltage */ + TPS65219_INT_BUCK1_RV, + TPS65219_INT_BUCK2_RV, + TPS65219_INT_BUCK3_RV, + TPS65219_INT_LDO1_RV, + TPS65219_INT_LDO2_RV, + TPS65219_INT_LDO3_RV, + TPS65219_INT_LDO4_RV, + /* Residual Voltage ShutDown */ + TPS65219_INT_BUCK1_RV_SD, + TPS65219_INT_BUCK2_RV_SD, + TPS65219_INT_BUCK3_RV_SD, + TPS65219_INT_LDO1_RV_SD, + TPS65219_INT_LDO2_RV_SD, + TPS65219_INT_LDO3_RV_SD, + TPS65219_INT_LDO4_RV_SD, + TPS65219_INT_TIMEOUT, + /* Power Button */ + TPS65219_INT_PB_FALLING_EDGE_DETECT, + TPS65219_INT_PB_RISING_EDGE_DETECT, +}; + +enum tps65219_regulator_id { + /* DCDC's */ + TPS65219_BUCK_1, + TPS65219_BUCK_2, + TPS65219_BUCK_3, + /* LDOs */ + TPS65219_LDO_1, + TPS65219_LDO_2, + TPS65219_LDO_3, + TPS65219_LDO_4, +}; + +/* Number of step-down converters available */ +#define TPS65219_NUM_DCDC 3 +/* Number of LDO voltage regulators available */ +#define TPS65219_NUM_LDO 4 +/* Number of total regulators available */ +#define TPS65219_NUM_REGULATOR (TPS65219_NUM_DCDC + TPS65219_NUM_LDO) + +/* Define the TPS65219 IRQ numbers */ +enum tps65219_irqs { + /* INT source registers */ + TPS65219_TO_RV_SD_SET_IRQ, + TPS65219_RV_SET_IRQ, + TPS65219_SYS_SET_IRQ, + TPS65219_BUCK_1_2_SET_IRQ, + TPS65219_BUCK_3_SET_IRQ, + TPS65219_LDO_1_2_SET_IRQ, + TPS65219_LDO_3_4_SET_IRQ, + TPS65219_PB_SET_IRQ, +}; + +/** + * struct tps65219 - tps65219 sub-driver chip access routines + * + * Device data may be used to access the TPS65219 chip + * + * @dev: MFD device + * @regmap: Regmap for accessing the device registers + * @irq_data: Regmap irq data used for the irq chip + * @nb: notifier block for the restart handler + */ +struct tps65219 { + struct device *dev; + struct regmap *regmap; + + struct regmap_irq_chip_data *irq_data; + struct notifier_block nb; +}; + +#endif /* MFD_TPS65219_H */ diff --git a/include/linux/mfd/twl6040.h b/include/linux/mfd/twl6040.h index 1fc7450bd8ab..286a724e379a 100644 --- a/include/linux/mfd/twl6040.h +++ b/include/linux/mfd/twl6040.h @@ -174,35 +174,7 @@ #define TWL6040_GPO_MAX 3 -/* TODO: All platform data struct can be removed */ -struct twl6040_codec_data { - u16 hs_left_step; - u16 hs_right_step; - u16 hf_left_step; - u16 hf_right_step; -}; - -struct twl6040_vibra_data { - unsigned int vibldrv_res; /* left driver resistance */ - unsigned int vibrdrv_res; /* right driver resistance */ - unsigned int viblmotor_res; /* left motor resistance */ - unsigned int vibrmotor_res; /* right motor resistance */ - int vddvibl_uV; /* VDDVIBL volt, set 0 for fixed reg */ - int vddvibr_uV; /* VDDVIBR volt, set 0 for fixed reg */ -}; - -struct twl6040_gpo_data { - int gpio_base; -}; - -struct twl6040_platform_data { - int audpwron_gpio; /* audio power-on gpio */ - - struct twl6040_codec_data *codec; - struct twl6040_vibra_data *vibra; - struct twl6040_gpo_data *gpo; -}; - +struct gpio_desc; struct regmap; struct regmap_irq_chips_data; @@ -218,7 +190,7 @@ struct twl6040 { struct mfd_cell cells[TWL6040_CELLS]; struct completion ready; - int audpwron; + struct gpio_desc *audpwron; int power_count; int rev; |