summaryrefslogtreecommitdiffstats
path: root/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'drivers')
-rw-r--r--drivers/net/ixgbe/ixgbe_82599.c120
-rw-r--r--drivers/net/ixgbe/ixgbe_common.c1
-rw-r--r--drivers/net/ixgbe/ixgbe_phy.c1
-rw-r--r--drivers/net/ixgbe/ixgbe_type.h7
4 files changed, 106 insertions, 23 deletions
diff --git a/drivers/net/ixgbe/ixgbe_82599.c b/drivers/net/ixgbe/ixgbe_82599.c
index a7611bbf3873..84b83f7b473f 100644
--- a/drivers/net/ixgbe/ixgbe_82599.c
+++ b/drivers/net/ixgbe/ixgbe_82599.c
@@ -461,12 +461,23 @@ s32 ixgbe_setup_mac_link_speed_multispeed_fiber(struct ixgbe_hw *hw,
u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP);
bool link_up = false;
bool negotiation;
+ int i;
/* Mask off requested but non-supported speeds */
hw->mac.ops.get_link_capabilities(hw, &phy_link_speed, &negotiation);
speed &= phy_link_speed;
/*
+ * When the driver changes the link speeds that it can support,
+ * it sets autotry_restart to true to indicate that we need to
+ * initiate a new autotry session with the link partner. To do
+ * so, we set the speed then disable and re-enable the tx laser, to
+ * alert the link partner that it also needs to restart autotry on its
+ * end. This is consistent with true clause 37 autoneg, which also
+ * involves a loss of signal.
+ */
+
+ /*
* Try each speed one by one, highest priority first. We do this in
* software because 10gb fiber doesn't support speed autonegotiation.
*/
@@ -474,21 +485,52 @@ s32 ixgbe_setup_mac_link_speed_multispeed_fiber(struct ixgbe_hw *hw,
speedcnt++;
highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL;
- /* Set hardware SDP's */
+ /* If we already have link at this speed, just jump out */
+ hw->mac.ops.check_link(hw, &phy_link_speed, &link_up, false);
+
+ if ((phy_link_speed == IXGBE_LINK_SPEED_10GB_FULL) && link_up)
+ goto out;
+
+ /* Set the module link speed */
esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5);
IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
- ixgbe_setup_mac_link_speed_82599(hw,
- IXGBE_LINK_SPEED_10GB_FULL,
- autoneg,
- autoneg_wait_to_complete);
-
- msleep(50);
+ /* Allow module to change analog characteristics (1G->10G) */
+ msleep(40);
- /* If we have link, just jump out */
- hw->mac.ops.check_link(hw, &phy_link_speed, &link_up, false);
- if (link_up)
+ status = ixgbe_setup_mac_link_speed_82599(hw,
+ IXGBE_LINK_SPEED_10GB_FULL,
+ autoneg,
+ autoneg_wait_to_complete);
+ if (status != 0)
goto out;
+
+ /* Flap the tx laser if it has not already been done */
+ if (hw->mac.autotry_restart) {
+ /* Disable tx laser; allow 100us to go dark per spec */
+ esdp_reg |= IXGBE_ESDP_SDP3;
+ IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
+ udelay(100);
+
+ /* Enable tx laser; allow 2ms to light up per spec */
+ esdp_reg &= ~IXGBE_ESDP_SDP3;
+ IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
+ msleep(2);
+
+ hw->mac.autotry_restart = false;
+ }
+
+ /* The controller may take up to 500ms at 10g to acquire link */
+ for (i = 0; i < 5; i++) {
+ /* Wait for the link partner to also set speed */
+ msleep(100);
+
+ /* If we have link, just jump out */
+ hw->mac.ops.check_link(hw, &phy_link_speed,
+ &link_up, false);
+ if (link_up)
+ goto out;
+ }
}
if (speed & IXGBE_LINK_SPEED_1GB_FULL) {
@@ -496,16 +538,44 @@ s32 ixgbe_setup_mac_link_speed_multispeed_fiber(struct ixgbe_hw *hw,
if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN)
highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL;
- /* Set hardware SDP's */
+ /* If we already have link at this speed, just jump out */
+ hw->mac.ops.check_link(hw, &phy_link_speed, &link_up, false);
+
+ if ((phy_link_speed == IXGBE_LINK_SPEED_1GB_FULL) && link_up)
+ goto out;
+
+ /* Set the module link speed */
esdp_reg &= ~IXGBE_ESDP_SDP5;
esdp_reg |= IXGBE_ESDP_SDP5_DIR;
IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
- ixgbe_setup_mac_link_speed_82599(
- hw, IXGBE_LINK_SPEED_1GB_FULL, autoneg,
- autoneg_wait_to_complete);
+ /* Allow module to change analog characteristics (10G->1G) */
+ msleep(40);
- msleep(50);
+ status = ixgbe_setup_mac_link_speed_82599(hw,
+ IXGBE_LINK_SPEED_1GB_FULL,
+ autoneg,
+ autoneg_wait_to_complete);
+ if (status != 0)
+ goto out;
+
+ /* Flap the tx laser if it has not already been done */
+ if (hw->mac.autotry_restart) {
+ /* Disable tx laser; allow 100us to go dark per spec */
+ esdp_reg |= IXGBE_ESDP_SDP3;
+ IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
+ udelay(100);
+
+ /* Enable tx laser; allow 2ms to light up per spec */
+ esdp_reg &= ~IXGBE_ESDP_SDP3;
+ IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
+ msleep(2);
+
+ hw->mac.autotry_restart = false;
+ }
+
+ /* Wait for the link partner to also set speed */
+ msleep(100);
/* If we have link, just jump out */
hw->mac.ops.check_link(hw, &phy_link_speed, &link_up, false);
@@ -591,6 +661,7 @@ s32 ixgbe_setup_mac_link_speed_82599(struct ixgbe_hw *hw,
s32 status = 0;
u32 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
u32 autoc2 = IXGBE_READ_REG(hw, IXGBE_AUTOC2);
+ u32 start_autoc = autoc;
u32 orig_autoc = 0;
u32 link_mode = autoc & IXGBE_AUTOC_LMS_MASK;
u32 pma_pmd_1g = autoc & IXGBE_AUTOC_1G_PMA_PMD_MASK;
@@ -603,6 +674,11 @@ s32 ixgbe_setup_mac_link_speed_82599(struct ixgbe_hw *hw,
hw->mac.ops.get_link_capabilities(hw, &link_capabilities, &autoneg);
speed &= link_capabilities;
+ if (speed == IXGBE_LINK_SPEED_UNKNOWN) {
+ status = IXGBE_ERR_LINK_SETUP;
+ goto out;
+ }
+
/* Use stored value (EEPROM defaults) of AUTOC to find KR/KX4 support*/
if (hw->mac.orig_link_settings_stored)
orig_autoc = hw->mac.orig_autoc;
@@ -610,11 +686,9 @@ s32 ixgbe_setup_mac_link_speed_82599(struct ixgbe_hw *hw,
orig_autoc = autoc;
- if (speed == IXGBE_LINK_SPEED_UNKNOWN) {
- status = IXGBE_ERR_LINK_SETUP;
- } else if (link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR ||
- link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN ||
- link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) {
+ if (link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR ||
+ link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN ||
+ link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) {
/* Set KX4/KX/KR support according to speed requested */
autoc &= ~(IXGBE_AUTOC_KX4_KX_SUPP_MASK | IXGBE_AUTOC_KR_SUPP);
if (speed & IXGBE_LINK_SPEED_10GB_FULL)
@@ -646,7 +720,7 @@ s32 ixgbe_setup_mac_link_speed_82599(struct ixgbe_hw *hw,
}
}
- if (status == 0) {
+ if (autoc != start_autoc) {
/* Restart link */
autoc |= IXGBE_AUTOC_AN_RESTART;
IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc);
@@ -680,6 +754,7 @@ s32 ixgbe_setup_mac_link_speed_82599(struct ixgbe_hw *hw,
msleep(50);
}
+out:
return status;
}
@@ -1144,6 +1219,9 @@ s32 ixgbe_start_hw_82599(struct ixgbe_hw *hw)
}
IXGBE_WRITE_FLUSH(hw);
+ /* We need to run link autotry after the driver loads */
+ hw->mac.autotry_restart = true;
+
return 0;
}
diff --git a/drivers/net/ixgbe/ixgbe_common.c b/drivers/net/ixgbe/ixgbe_common.c
index 6f79409270a7..4d36cd32cd30 100644
--- a/drivers/net/ixgbe/ixgbe_common.c
+++ b/drivers/net/ixgbe/ixgbe_common.c
@@ -2068,6 +2068,7 @@ s32 ixgbe_blink_led_start_generic(struct ixgbe_hw *hw, u32 index)
hw->mac.ops.check_link(hw, &speed, &link_up, false);
if (!link_up) {
+ autoc_reg |= IXGBE_AUTOC_AN_RESTART;
autoc_reg |= IXGBE_AUTOC_FLU;
IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
msleep(10);
diff --git a/drivers/net/ixgbe/ixgbe_phy.c b/drivers/net/ixgbe/ixgbe_phy.c
index e43d6248d7d4..453e966762f0 100644
--- a/drivers/net/ixgbe/ixgbe_phy.c
+++ b/drivers/net/ixgbe/ixgbe_phy.c
@@ -606,6 +606,7 @@ s32 ixgbe_identify_sfp_module_generic(struct ixgbe_hw *hw)
hw->phy.sfp_setup_needed = true;
/* Determine if the SFP+ PHY is dual speed or not. */
+ hw->phy.multispeed_fiber = false;
if (((comp_codes_1g & IXGBE_SFF_1GBASESX_CAPABLE) &&
(comp_codes_10g & IXGBE_SFF_10GBASESR_CAPABLE)) ||
((comp_codes_1g & IXGBE_SFF_1GBASELX_CAPABLE) &&
diff --git a/drivers/net/ixgbe/ixgbe_type.h b/drivers/net/ixgbe/ixgbe_type.h
index a8a8243d8fdb..199b288c3459 100644
--- a/drivers/net/ixgbe/ixgbe_type.h
+++ b/drivers/net/ixgbe/ixgbe_type.h
@@ -1265,8 +1265,10 @@
#define IXGBE_STATUS_LAN_ID_1 0x00000004 /* LAN ID 1 */
/* ESDP Bit Masks */
-#define IXGBE_ESDP_SDP0 0x00000001
-#define IXGBE_ESDP_SDP1 0x00000002
+#define IXGBE_ESDP_SDP0 0x00000001 /* SDP0 Data Value */
+#define IXGBE_ESDP_SDP1 0x00000002 /* SDP1 Data Value */
+#define IXGBE_ESDP_SDP2 0x00000004 /* SDP2 Data Value */
+#define IXGBE_ESDP_SDP3 0x00000008 /* SDP3 Data Value */
#define IXGBE_ESDP_SDP4 0x00000010 /* SDP4 Data Value */
#define IXGBE_ESDP_SDP5 0x00000020 /* SDP5 Data Value */
#define IXGBE_ESDP_SDP6 0x00000040 /* SDP6 Data Value */
@@ -2281,6 +2283,7 @@ struct ixgbe_mac_info {
bool orig_link_settings_stored;
bool autoneg;
bool autoneg_succeeded;
+ bool autotry_restart;
};
struct ixgbe_phy_info {
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-19 05:31:33 +0000