summaryrefslogtreecommitdiffstats
path: root/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'drivers')
-rw-r--r--drivers/thermal/Kconfig33
-rw-r--r--drivers/thermal/Makefile6
-rw-r--r--drivers/thermal/cpu_cooling.c8
-rw-r--r--drivers/thermal/exynos_thermal.c1059
-rw-r--r--drivers/thermal/imx_thermal.c541
-rw-r--r--drivers/thermal/samsung/Kconfig18
-rw-r--r--drivers/thermal/samsung/Makefile7
-rw-r--r--drivers/thermal/samsung/exynos_thermal_common.c432
-rw-r--r--drivers/thermal/samsung/exynos_thermal_common.h107
-rw-r--r--drivers/thermal/samsung/exynos_tmu.c762
-rw-r--r--drivers/thermal/samsung/exynos_tmu.h311
-rw-r--r--drivers/thermal/samsung/exynos_tmu_data.c250
-rw-r--r--drivers/thermal/samsung/exynos_tmu_data.h155
-rw-r--r--drivers/thermal/step_wise.c32
-rw-r--r--drivers/thermal/thermal_core.c282
-rw-r--r--drivers/thermal/thermal_hwmon.c269
-rw-r--r--drivers/thermal/thermal_hwmon.h49
-rw-r--r--drivers/thermal/ti-soc-thermal/dra752-thermal-data.c5
-rw-r--r--drivers/thermal/ti-soc-thermal/ti-bandgap.c6
-rw-r--r--drivers/thermal/ti-soc-thermal/ti-thermal-common.c7
20 files changed, 2997 insertions, 1342 deletions
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index e988c81d763c..dbfc390330ac 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -17,8 +17,17 @@ if THERMAL
config THERMAL_HWMON
bool
+ prompt "Expose thermal sensors as hwmon device"
depends on HWMON=y || HWMON=THERMAL
default y
+ help
+ In case a sensor is registered with the thermal
+ framework, this option will also register it
+ as a hwmon. The sensor will then have the common
+ hwmon sysfs interface.
+
+ Say 'Y' here if you want all thermal sensors to
+ have hwmon sysfs interface too.
choice
prompt "Default Thermal governor"
@@ -91,6 +100,17 @@ config THERMAL_EMULATION
because userland can easily disable the thermal policy by simply
flooding this sysfs node with low temperature values.
+config IMX_THERMAL
+ tristate "Temperature sensor driver for Freescale i.MX SoCs"
+ depends on CPU_THERMAL
+ depends on MFD_SYSCON
+ depends on OF
+ help
+ Support for Temperature Monitor (TEMPMON) found on Freescale i.MX SoCs.
+ It supports one critical trip point and one passive trip point. The
+ cpufreq is used as the cooling device to throttle CPUs when the
+ passive trip is crossed.
+
config SPEAR_THERMAL
bool "SPEAr thermal sensor driver"
depends on PLAT_SPEAR
@@ -114,14 +134,6 @@ config KIRKWOOD_THERMAL
Support for the Kirkwood thermal sensor driver into the Linux thermal
framework. Only kirkwood 88F6282 and 88F6283 have this sensor.
-config EXYNOS_THERMAL
- tristate "Temperature sensor on Samsung EXYNOS"
- depends on (ARCH_EXYNOS4 || ARCH_EXYNOS5)
- depends on CPU_THERMAL
- help
- If you say yes here you get support for TMU (Thermal Management
- Unit) on SAMSUNG EXYNOS series of SoC.
-
config DOVE_THERMAL
tristate "Temperature sensor on Marvell Dove SoCs"
depends on ARCH_DOVE
@@ -184,4 +196,9 @@ menu "Texas Instruments thermal drivers"
source "drivers/thermal/ti-soc-thermal/Kconfig"
endmenu
+menu "Samsung thermal drivers"
+depends on PLAT_SAMSUNG
+source "drivers/thermal/samsung/Kconfig"
+endmenu
+
endif
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index 67184a293e3f..584b36319d51 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -5,6 +5,9 @@
obj-$(CONFIG_THERMAL) += thermal_sys.o
thermal_sys-y += thermal_core.o
+# interface to/from other layers providing sensors
+thermal_sys-$(CONFIG_THERMAL_HWMON) += thermal_hwmon.o
+
# governors
thermal_sys-$(CONFIG_THERMAL_GOV_FAIR_SHARE) += fair_share.o
thermal_sys-$(CONFIG_THERMAL_GOV_STEP_WISE) += step_wise.o
@@ -17,10 +20,11 @@ thermal_sys-$(CONFIG_CPU_THERMAL) += cpu_cooling.o
obj-$(CONFIG_SPEAR_THERMAL) += spear_thermal.o
obj-$(CONFIG_RCAR_THERMAL) += rcar_thermal.o
obj-$(CONFIG_KIRKWOOD_THERMAL) += kirkwood_thermal.o
-obj-$(CONFIG_EXYNOS_THERMAL) += exynos_thermal.o
+obj-y += samsung/
obj-$(CONFIG_DOVE_THERMAL) += dove_thermal.o
obj-$(CONFIG_DB8500_THERMAL) += db8500_thermal.o
obj-$(CONFIG_ARMADA_THERMAL) += armada_thermal.o
+obj-$(CONFIG_IMX_THERMAL) += imx_thermal.o
obj-$(CONFIG_DB8500_CPUFREQ_COOLING) += db8500_cpufreq_cooling.o
obj-$(CONFIG_INTEL_POWERCLAMP) += intel_powerclamp.o
obj-$(CONFIG_X86_PKG_TEMP_THERMAL) += x86_pkg_temp_thermal.o
diff --git a/drivers/thermal/cpu_cooling.c b/drivers/thermal/cpu_cooling.c
index 82e15dbb3ac7..d17902886c3f 100644
--- a/drivers/thermal/cpu_cooling.c
+++ b/drivers/thermal/cpu_cooling.c
@@ -322,6 +322,8 @@ static int cpufreq_thermal_notifier(struct notifier_block *nb,
if (cpumask_test_cpu(policy->cpu, &notify_device->allowed_cpus))
max_freq = notify_device->cpufreq_val;
+ else
+ return 0;
/* Never exceed user_policy.max */
if (max_freq > policy->user_policy.max)
@@ -496,8 +498,12 @@ EXPORT_SYMBOL_GPL(cpufreq_cooling_register);
*/
void cpufreq_cooling_unregister(struct thermal_cooling_device *cdev)
{
- struct cpufreq_cooling_device *cpufreq_dev = cdev->devdata;
+ struct cpufreq_cooling_device *cpufreq_dev;
+
+ if (!cdev)
+ return;
+ cpufreq_dev = cdev->devdata;
mutex_lock(&cooling_cpufreq_lock);
cpufreq_dev_count--;
diff --git a/drivers/thermal/exynos_thermal.c b/drivers/thermal/exynos_thermal.c
deleted file mode 100644
index 9af4b93c9f86..000000000000
--- a/drivers/thermal/exynos_thermal.c
+++ /dev/null
@@ -1,1059 +0,0 @@
-/*
- * exynos_thermal.c - Samsung EXYNOS TMU (Thermal Management Unit)
- *
- * Copyright (C) 2011 Samsung Electronics
- * Donggeun Kim <dg77.kim@samsung.com>
- * Amit Daniel Kachhap <amit.kachhap@linaro.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- */
-
-#include <linux/module.h>
-#include <linux/err.h>
-#include <linux/kernel.h>
-#include <linux/slab.h>
-#include <linux/platform_device.h>
-#include <linux/interrupt.h>
-#include <linux/clk.h>
-#include <linux/workqueue.h>
-#include <linux/sysfs.h>
-#include <linux/kobject.h>
-#include <linux/io.h>
-#include <linux/mutex.h>
-#include <linux/platform_data/exynos_thermal.h>
-#include <linux/thermal.h>
-#include <linux/cpufreq.h>
-#include <linux/cpu_cooling.h>
-#include <linux/of.h>
-
-/* Exynos generic registers */
-#define EXYNOS_TMU_REG_TRIMINFO 0x0
-#define EXYNOS_TMU_REG_CONTROL 0x20
-#define EXYNOS_TMU_REG_STATUS 0x28
-#define EXYNOS_TMU_REG_CURRENT_TEMP 0x40
-#define EXYNOS_TMU_REG_INTEN 0x70
-#define EXYNOS_TMU_REG_INTSTAT 0x74
-#define EXYNOS_TMU_REG_INTCLEAR 0x78
-
-#define EXYNOS_TMU_TRIM_TEMP_MASK 0xff
-#define EXYNOS_TMU_GAIN_SHIFT 8
-#define EXYNOS_TMU_REF_VOLTAGE_SHIFT 24
-#define EXYNOS_TMU_CORE_ON 3
-#define EXYNOS_TMU_CORE_OFF 2
-#define EXYNOS_TMU_DEF_CODE_TO_TEMP_OFFSET 50
-
-/* Exynos4210 specific registers */
-#define EXYNOS4210_TMU_REG_THRESHOLD_TEMP 0x44
-#define EXYNOS4210_TMU_REG_TRIG_LEVEL0 0x50
-#define EXYNOS4210_TMU_REG_TRIG_LEVEL1 0x54
-#define EXYNOS4210_TMU_REG_TRIG_LEVEL2 0x58
-#define EXYNOS4210_TMU_REG_TRIG_LEVEL3 0x5C
-#define EXYNOS4210_TMU_REG_PAST_TEMP0 0x60
-#define EXYNOS4210_TMU_REG_PAST_TEMP1 0x64
-#define EXYNOS4210_TMU_REG_PAST_TEMP2 0x68
-#define EXYNOS4210_TMU_REG_PAST_TEMP3 0x6C
-
-#define EXYNOS4210_TMU_TRIG_LEVEL0_MASK 0x1
-#define EXYNOS4210_TMU_TRIG_LEVEL1_MASK 0x10
-#define EXYNOS4210_TMU_TRIG_LEVEL2_MASK 0x100
-#define EXYNOS4210_TMU_TRIG_LEVEL3_MASK 0x1000
-#define EXYNOS4210_TMU_INTCLEAR_VAL 0x1111
-
-/* Exynos5250 and Exynos4412 specific registers */
-#define EXYNOS_TMU_TRIMINFO_CON 0x14
-#define EXYNOS_THD_TEMP_RISE 0x50
-#define EXYNOS_THD_TEMP_FALL 0x54
-#define EXYNOS_EMUL_CON 0x80
-
-#define EXYNOS_TRIMINFO_RELOAD 0x1
-#define EXYNOS_TMU_CLEAR_RISE_INT 0x111
-#define EXYNOS_TMU_CLEAR_FALL_INT (0x111 << 12)
-#define EXYNOS_MUX_ADDR_VALUE 6
-#define EXYNOS_MUX_ADDR_SHIFT 20
-#define EXYNOS_TMU_TRIP_MODE_SHIFT 13
-
-#define EFUSE_MIN_VALUE 40
-#define EFUSE_MAX_VALUE 100
-
-/* In-kernel thermal framework related macros & definations */
-#define SENSOR_NAME_LEN 16
-#define MAX_TRIP_COUNT 8
-#define MAX_COOLING_DEVICE 4
-#define MAX_THRESHOLD_LEVS 4
-
-#define ACTIVE_INTERVAL 500
-#define IDLE_INTERVAL 10000
-#define MCELSIUS 1000
-
-#ifdef CONFIG_THERMAL_EMULATION
-#define EXYNOS_EMUL_TIME 0x57F0
-#define EXYNOS_EMUL_TIME_SHIFT 16
-#define EXYNOS_EMUL_DATA_SHIFT 8
-#define EXYNOS_EMUL_DATA_MASK 0xFF
-#define EXYNOS_EMUL_ENABLE 0x1
-#endif /* CONFIG_THERMAL_EMULATION */
-
-/* CPU Zone information */
-#define PANIC_ZONE 4
-#define WARN_ZONE 3
-#define MONITOR_ZONE 2
-#define SAFE_ZONE 1
-
-#define GET_ZONE(trip) (trip + 2)
-#define GET_TRIP(zone) (zone - 2)
-
-#define EXYNOS_ZONE_COUNT 3
-
-struct exynos_tmu_data {
- struct exynos_tmu_platform_data *pdata;
- struct resource *mem;
- void __iomem *base;
- int irq;
- enum soc_type soc;
- struct work_struct irq_work;
- struct mutex lock;
- struct clk *clk;
- u8 temp_error1, temp_error2;
-};
-
-struct thermal_trip_point_conf {
- int trip_val[MAX_TRIP_COUNT];
- int trip_count;
- u8 trigger_falling;
-};
-
-struct thermal_cooling_conf {
- struct freq_clip_table freq_data[MAX_TRIP_COUNT];
- int freq_clip_count;
-};
-
-struct thermal_sensor_conf {
- char name[SENSOR_NAME_LEN];
- int (*read_temperature)(void *data);
- int (*write_emul_temp)(void *drv_data, unsigned long temp);
- struct thermal_trip_point_conf trip_data;
- struct thermal_cooling_conf cooling_data;
- void *private_data;
-};
-
-struct exynos_thermal_zone {
- enum thermal_device_mode mode;
- struct thermal_zone_device *therm_dev;
- struct thermal_cooling_device *cool_dev[MAX_COOLING_DEVICE];
- unsigned int cool_dev_size;
- struct platform_device *exynos4_dev;
- struct thermal_sensor_conf *sensor_conf;
- bool bind;
-};
-
-static struct exynos_thermal_zone *th_zone;
-static void exynos_unregister_thermal(void);
-static int exynos_register_thermal(struct thermal_sensor_conf *sensor_conf);
-
-/* Get mode callback functions for thermal zone */
-static int exynos_get_mode(struct thermal_zone_device *thermal,
- enum thermal_device_mode *mode)
-{
- if (th_zone)
- *mode = th_zone->mode;
- return 0;
-}
-
-/* Set mode callback functions for thermal zone */
-static int exynos_set_mode(struct thermal_zone_device *thermal,
- enum thermal_device_mode mode)
-{
- if (!th_zone->therm_dev) {
- pr_notice("thermal zone not registered\n");
- return 0;
- }
-
- mutex_lock(&th_zone->therm_dev->lock);
-
- if (mode == THERMAL_DEVICE_ENABLED &&
- !th_zone->sensor_conf->trip_data.trigger_falling)
- th_zone->therm_dev->polling_delay = IDLE_INTERVAL;
- else
- th_zone->therm_dev->polling_delay = 0;
-
- mutex_unlock(&th_zone->therm_dev->lock);
-
- th_zone->mode = mode;
- thermal_zone_device_update(th_zone->therm_dev);
- pr_info("thermal polling set for duration=%d msec\n",
- th_zone->therm_dev->polling_delay);
- return 0;
-}
-
-
-/* Get trip type callback functions for thermal zone */
-static int exynos_get_trip_type(struct thermal_zone_device *thermal, int trip,
- enum thermal_trip_type *type)
-{
- switch (GET_ZONE(trip)) {
- case MONITOR_ZONE:
- case WARN_ZONE:
- *type = THERMAL_TRIP_ACTIVE;
- break;
- case PANIC_ZONE:
- *type = THERMAL_TRIP_CRITICAL;
- break;
- default:
- return -EINVAL;
- }
- return 0;
-}
-
-/* Get trip temperature callback functions for thermal zone */
-static int exynos_get_trip_temp(struct thermal_zone_device *thermal, int trip,
- unsigned long *temp)
-{
- if (trip < GET_TRIP(MONITOR_ZONE) || trip > GET_TRIP(PANIC_ZONE))
- return -EINVAL;
-
- *temp = th_zone->sensor_conf->trip_data.trip_val[trip];
- /* convert the temperature into millicelsius */
- *temp = *temp * MCELSIUS;
-
- return 0;
-}
-
-/* Get critical temperature callback functions for thermal zone */
-static int exynos_get_crit_temp(struct thermal_zone_device *thermal,
- unsigned long *temp)
-{
- int ret;
- /* Panic zone */
- ret = exynos_get_trip_temp(thermal, GET_TRIP(PANIC_ZONE), temp);
- return ret;
-}
-
-/* Bind callback functions for thermal zone */
-static int exynos_bind(struct thermal_zone_device *thermal,
- struct thermal_cooling_device *cdev)
-{
- int ret = 0, i, tab_size, level;
- struct freq_clip_table *tab_ptr, *clip_data;
- struct thermal_sensor_conf *data = th_zone->sensor_conf;
-
- tab_ptr = (struct freq_clip_table *)data->cooling_data.freq_data;
- tab_size = data->cooling_data.freq_clip_count;
-
- if (tab_ptr == NULL || tab_size == 0)
- return -EINVAL;
-
- /* find the cooling device registered*/
- for (i = 0; i < th_zone->cool_dev_size; i++)
- if (cdev == th_zone->cool_dev[i])
- break;
-
- /* No matching cooling device */
- if (i == th_zone->cool_dev_size)
- return 0;
-
- /* Bind the thermal zone to the cpufreq cooling device */
- for (i = 0; i < tab_size; i++) {
- clip_data = (struct freq_clip_table *)&(tab_ptr[i]);
- level = cpufreq_cooling_get_level(0, clip_data->freq_clip_max);
- if (level == THERMAL_CSTATE_INVALID)
- return 0;
- switch (GET_ZONE(i)) {
- case MONITOR_ZONE:
- case WARN_ZONE:
- if (thermal_zone_bind_cooling_device(thermal, i, cdev,
- level, 0)) {
- pr_err("error binding cdev inst %d\n", i);
- ret = -EINVAL;
- }
- th_zone->bind = true;
- break;
- default:
- ret = -EINVAL;
- }
- }
-
- return ret;
-}
-
-/* Unbind callback functions for thermal zone */
-static int exynos_unbind(struct thermal_zone_device *thermal,
- struct thermal_cooling_device *cdev)
-{
- int ret = 0, i, tab_size;
- struct thermal_sensor_conf *data = th_zone->sensor_conf;
-
- if (th_zone->bind == false)
- return 0;
-
- tab_size = data->cooling_data.freq_clip_count;
-
- if (tab_size == 0)
- return -EINVAL;
-
- /* find the cooling device registered*/
- for (i = 0; i < th_zone->cool_dev_size; i++)
- if (cdev == th_zone->cool_dev[i])
- break;
-
- /* No matching cooling device */
- if (i == th_zone->cool_dev_size)
- return 0;
-
- /* Bind the thermal zone to the cpufreq cooling device */
- for (i = 0; i < tab_size; i++) {
- switch (GET_ZONE(i)) {
- case MONITOR_ZONE:
- case WARN_ZONE:
- if (thermal_zone_unbind_cooling_device(thermal, i,
- cdev)) {
- pr_err("error unbinding cdev inst=%d\n", i);
- ret = -EINVAL;
- }
- th_zone->bind = false;
- break;
- default:
- ret = -EINVAL;
- }
- }
- return ret;
-}
-
-/* Get temperature callback functions for thermal zone */
-static int exynos_get_temp(struct thermal_zone_device *thermal,
- unsigned long *temp)
-{
- void *data;
-
- if (!th_zone->sensor_conf) {
- pr_info("Temperature sensor not initialised\n");
- return -EINVAL;
- }
- data = th_zone->sensor_conf->private_data;
- *temp = th_zone->sensor_conf->read_temperature(data);
- /* convert the temperature into millicelsius */
- *temp = *temp * MCELSIUS;
- return 0;
-}
-
-/* Get temperature callback functions for thermal zone */
-static int exynos_set_emul_temp(struct thermal_zone_device *thermal,
- unsigned long temp)
-{
- void *data;
- int ret = -EINVAL;
-
- if (!th_zone->sensor_conf) {
- pr_info("Temperature sensor not initialised\n");
- return -EINVAL;
- }
- data = th_zone->sensor_conf->private_data;
- if (th_zone->sensor_conf->write_emul_temp)
- ret = th_zone->sensor_conf->write_emul_temp(data, temp);
- return ret;
-}
-
-/* Get the temperature trend */
-static int exynos_get_trend(struct thermal_zone_device *thermal,
- int trip, enum thermal_trend *trend)
-{
- int ret;
- unsigned long trip_temp;
-
- ret = exynos_get_trip_temp(thermal, trip, &trip_temp);
- if (ret < 0)
- return ret;
-
- if (thermal->temperature >= trip_temp)
- *trend = THERMAL_TREND_RAISE_FULL;
- else
- *trend = THERMAL_TREND_DROP_FULL;
-
- return 0;
-}
-/* Operation callback functions for thermal zone */
-static struct thermal_zone_device_ops const exynos_dev_ops = {
- .bind = exynos_bind,
- .unbind = exynos_unbind,
- .get_temp = exynos_get_temp,
- .set_emul_temp = exynos_set_emul_temp,
- .get_trend = exynos_get_trend,
- .get_mode = exynos_get_mode,
- .set_mode = exynos_set_mode,
- .get_trip_type = exynos_get_trip_type,
- .get_trip_temp = exynos_get_trip_temp,
- .get_crit_temp = exynos_get_crit_temp,
-};
-
-/*
- * This function may be called from interrupt based temperature sensor
- * when threshold is changed.
- */
-static void exynos_report_trigger(void)
-{
- unsigned int i;
- char data[10];
- char *envp[] = { data, NULL };
-
- if (!th_zone || !th_zone->therm_dev)
- return;
- if (th_zone->bind == false) {
- for (i = 0; i < th_zone->cool_dev_size; i++) {
- if (!th_zone->cool_dev[i])
- continue;
- exynos_bind(th_zone->therm_dev,
- th_zone->cool_dev[i]);
- }
- }
-
- thermal_zone_device_update(th_zone->therm_dev);
-
- mutex_lock(&th_zone->therm_dev->lock);
- /* Find the level for which trip happened */
- for (i = 0; i < th_zone->sensor_conf->trip_data.trip_count; i++) {
- if (th_zone->therm_dev->last_temperature <
- th_zone->sensor_conf->trip_data.trip_val[i] * MCELSIUS)
- break;
- }
-
- if (th_zone->mode == THERMAL_DEVICE_ENABLED &&
- !th_zone->sensor_conf->trip_data.trigger_falling) {
- if (i > 0)
- th_zone->therm_dev->polling_delay = ACTIVE_INTERVAL;
- else
- th_zone->therm_dev->polling_delay = IDLE_INTERVAL;
- }
-
- snprintf(data, sizeof(data), "%u", i);
- kobject_uevent_env(&th_zone->therm_dev->device.kobj, KOBJ_CHANGE, envp);
- mutex_unlock(&th_zone->therm_dev->lock);
-}
-
-/* Register with the in-kernel thermal management */
-static int exynos_register_thermal(struct thermal_sensor_conf *sensor_conf)
-{
- int ret;
- struct cpumask mask_val;
-
- if (!sensor_conf || !sensor_conf->read_temperature) {
- pr_err("Temperature sensor not initialised\n");
- return -EINVAL;
- }
-
- th_zone = kzalloc(sizeof(struct exynos_thermal_zone), GFP_KERNEL);
- if (!th_zone)
- return -ENOMEM;
-
- th_zone->sensor_conf = sensor_conf;
- cpumask_set_cpu(0, &mask_val);
- th_zone->cool_dev[0] = cpufreq_cooling_register(&mask_val);
- if (IS_ERR(th_zone->cool_dev[0])) {
- pr_err("Failed to register cpufreq cooling device\n");
- ret = -EINVAL;
- goto err_unregister;
- }
- th_zone->cool_dev_size++;
-
- th_zone->therm_dev = thermal_zone_device_register(sensor_conf->name,
- EXYNOS_ZONE_COUNT, 0, NULL, &exynos_dev_ops, NULL, 0,
- sensor_conf->trip_data.trigger_falling ?
- 0 : IDLE_INTERVAL);
-
- if (IS_ERR(th_zone->therm_dev)) {
- pr_err("Failed to register thermal zone device\n");
- ret = PTR_ERR(th_zone->therm_dev);
- goto err_unregister;
- }
- th_zone->mode = THERMAL_DEVICE_ENABLED;
-
- pr_info("Exynos: Kernel Thermal management registered\n");
-
- return 0;
-
-err_unregister:
- exynos_unregister_thermal();
- return ret;
-}
-
-/* Un-Register with the in-kernel thermal management */
-static void exynos_unregister_thermal(void)
-{
- int i;
-
- if (!th_zone)
- return;
-
- if (th_zone->therm_dev)
- thermal_zone_device_unregister(th_zone->therm_dev);
-
- for (i = 0; i < th_zone->cool_dev_size; i++) {
- if (th_zone->cool_dev[i])
- cpufreq_cooling_unregister(th_zone->cool_dev[i]);
- }
-
- kfree(th_zone);
- pr_info("Exynos: Kernel Thermal management unregistered\n");
-}
-
-/*
- * TMU treats temperature as a mapped temperature code.
- * The temperature is converted differently depending on the calibration type.
- */
-static int temp_to_code(struct exynos_tmu_data *data, u8 temp)
-{
- struct exynos_tmu_platform_data *pdata = data->pdata;
- int temp_code;
-
- if (data->soc == SOC_ARCH_EXYNOS4210)
- /* temp should range between 25 and 125 */
- if (temp < 25 || temp > 125) {
- temp_code = -EINVAL;
- goto out;
- }
-
- switch (pdata->cal_type) {
- case TYPE_TWO_POINT_TRIMMING:
- temp_code = (temp - 25) *
- (data->temp_error2 - data->temp_error1) /
- (85 - 25) + data->temp_error1;
- break;
- case TYPE_ONE_POINT_TRIMMING:
- temp_code = temp + data->temp_error1 - 25;
- break;
- default:
- temp_code = temp + EXYNOS_TMU_DEF_CODE_TO_TEMP_OFFSET;
- break;
- }
-out:
- return temp_code;
-}
-
-/*
- * Calculate a temperature value from a temperature code.
- * The unit of the temperature is degree Celsius.
- */
-static int code_to_temp(struct exynos_tmu_data *data, u8 temp_code)
-{
- struct exynos_tmu_platform_data *pdata = data->pdata;
- int temp;
-
- if (data->soc == SOC_ARCH_EXYNOS4210)
- /* temp_code should range between 75 and 175 */
- if (temp_code < 75 || temp_code > 175) {
- temp = -ENODATA;
- goto out;
- }
-
- switch (pdata->cal_type) {
- case TYPE_TWO_POINT_TRIMMING:
- temp = (temp_code - data->temp_error1) * (85 - 25) /
- (data->temp_error2 - data->temp_error1) + 25;
- break;
- case TYPE_ONE_POINT_TRIMMING:
- temp = temp_code - data->temp_error1 + 25;
- break;
- default:
- temp = temp_code - EXYNOS_TMU_DEF_CODE_TO_TEMP_OFFSET;
- break;
- }
-out:
- return temp;
-}
-
-static int exynos_tmu_initialize(struct platform_device *pdev)
-{
- struct exynos_tmu_data *data = platform_get_drvdata(pdev);
- struct exynos_tmu_platform_data *pdata = data->pdata;
- unsigned int status, trim_info;
- unsigned int rising_threshold = 0, falling_threshold = 0;
- int ret = 0, threshold_code, i, trigger_levs = 0;
-
- mutex_lock(&data->lock);
- clk_enable(data->clk);
-
- status = readb(data->base + EXYNOS_TMU_REG_STATUS);
- if (!status) {
- ret = -EBUSY;
- goto out;
- }
-
- if (data->soc == SOC_ARCH_EXYNOS) {
- __raw_writel(EXYNOS_TRIMINFO_RELOAD,
- data->base + EXYNOS_TMU_TRIMINFO_CON);
- }
- /* Save trimming info in order to perform calibration */
- trim_info = readl(data->base + EXYNOS_TMU_REG_TRIMINFO);
- data->temp_error1 = trim_info & EXYNOS_TMU_TRIM_TEMP_MASK;
- data->temp_error2 = ((trim_info >> 8) & EXYNOS_TMU_TRIM_TEMP_MASK);
-
- if ((EFUSE_MIN_VALUE > data->temp_error1) ||
- (data->temp_error1 > EFUSE_MAX_VALUE) ||
- (data->temp_error2 != 0))
- data->temp_error1 = pdata->efuse_value;
-
- /* Count trigger levels to be enabled */
- for (i = 0; i < MAX_THRESHOLD_LEVS; i++)
- if (pdata->trigger_levels[i])
- trigger_levs++;
-
- if (data->soc == SOC_ARCH_EXYNOS4210) {
- /* Write temperature code for threshold */
- threshold_code = temp_to_code(data, pdata->threshold);
- if (threshold_code < 0) {
- ret = threshold_code;
- goto out;
- }
- writeb(threshold_code,
- data->base + EXYNOS4210_TMU_REG_THRESHOLD_TEMP);
- for (i = 0; i < trigger_levs; i++)
- writeb(pdata->trigger_levels[i],
- data->base + EXYNOS4210_TMU_REG_TRIG_LEVEL0 + i * 4);
-
- writel(EXYNOS4210_TMU_INTCLEAR_VAL,
- data->base + EXYNOS_TMU_REG_INTCLEAR);
- } else if (data->soc == SOC_ARCH_EXYNOS) {
- /* Write temperature code for rising and falling threshold */
- for (i = 0; i < trigger_levs; i++) {
- threshold_code = temp_to_code(data,
- pdata->trigger_levels[i]);
- if (threshold_code < 0) {
- ret = threshold_code;
- goto out;
- }
- rising_threshold |= threshold_code << 8 * i;
- if (pdata->threshold_falling) {
- threshold_code = temp_to_code(data,
- pdata->trigger_levels[i] -
- pdata->threshold_falling);
- if (threshold_code > 0)
- falling_threshold |=
- threshold_code << 8 * i;
- }
- }
-
- writel(rising_threshold,
- data->base + EXYNOS_THD_TEMP_RISE);
- writel(falling_threshold,
- data->base + EXYNOS_THD_TEMP_FALL);
-
- writel(EXYNOS_TMU_CLEAR_RISE_INT | EXYNOS_TMU_CLEAR_FALL_INT,
- data->base + EXYNOS_TMU_REG_INTCLEAR);
- }
-out:
- clk_disable(data->clk);
- mutex_unlock(&data->lock);
-
- return ret;
-}
-
-static void exynos_tmu_control(struct platform_device *pdev, bool on)
-{
- struct exynos_tmu_data *data = platform_get_drvdata(pdev);
- struct exynos_tmu_platform_data *pdata = data->pdata;
- unsigned int con, interrupt_en;
-
- mutex_lock(&data->lock);
- clk_enable(data->clk);
-
- con = pdata->reference_voltage << EXYNOS_TMU_REF_VOLTAGE_SHIFT |
- pdata->gain << EXYNOS_TMU_GAIN_SHIFT;
-
- if (data->soc == SOC_ARCH_EXYNOS) {
- con |= pdata->noise_cancel_mode << EXYNOS_TMU_TRIP_MODE_SHIFT;
- con |= (EXYNOS_MUX_ADDR_VALUE << EXYNOS_MUX_ADDR_SHIFT);
- }
-
- if (on) {
- con |= EXYNOS_TMU_CORE_ON;
- interrupt_en = pdata->trigger_level3_en << 12 |
- pdata->trigger_level2_en << 8 |
- pdata->trigger_level1_en << 4 |
- pdata->trigger_level0_en;
- if (pdata->threshold_falling)
- interrupt_en |= interrupt_en << 16;
- } else {
- con |= EXYNOS_TMU_CORE_OFF;
- interrupt_en = 0; /* Disable all interrupts */
- }
- writel(interrupt_en, data->base + EXYNOS_TMU_REG_INTEN);
- writel(con, data->base + EXYNOS_TMU_REG_CONTROL);
-
- clk_disable(data->clk);
- mutex_unlock(&data->lock);
-}
-
-static int exynos_tmu_read(struct exynos_tmu_data *data)
-{
- u8 temp_code;
- int temp;
-
- mutex_lock(&data->lock);
- clk_enable(data->clk);
-
- temp_code = readb(data->base + EXYNOS_TMU_REG_CURRENT_TEMP);
- temp = code_to_temp(data, temp_code);
-
- clk_disable(data->clk);
- mutex_unlock(&data->lock);
-
- return temp;
-}
-
-#ifdef CONFIG_THERMAL_EMULATION
-static int exynos_tmu_set_emulation(void *drv_data, unsigned long temp)
-{
- struct exynos_tmu_data *data = drv_data;
- unsigned int reg;
- int ret = -EINVAL;
-
- if (data->soc == SOC_ARCH_EXYNOS4210)
- goto out;
-
- if (temp && temp < MCELSIUS)
- goto out;
-
- mutex_lock(&data->lock);
- clk_enable(data->clk);
-
- reg = readl(data->base + EXYNOS_EMUL_CON);
-
- if (temp) {
- temp /= MCELSIUS;
-
- reg = (EXYNOS_EMUL_TIME << EXYNOS_EMUL_TIME_SHIFT) |
- (temp_to_code(data, temp)
- << EXYNOS_EMUL_DATA_SHIFT) | EXYNOS_EMUL_ENABLE;
- } else {
- reg &= ~EXYNOS_EMUL_ENABLE;
- }
-
- writel(reg, data->base + EXYNOS_EMUL_CON);
-
- clk_disable(data->clk);
- mutex_unlock(&data->lock);
- return 0;
-out:
- return ret;
-}
-#else
-static int exynos_tmu_set_emulation(void *drv_data, unsigned long temp)
- { return -EINVAL; }
-#endif/*CONFIG_THERMAL_EMULATION*/
-
-static void exynos_tmu_work(struct work_struct *work)
-{
- struct exynos_tmu_data *data = container_of(work,
- struct exynos_tmu_data, irq_work);
-
- exynos_report_trigger();
- mutex_lock(&data->lock);
- clk_enable(data->clk);
- if (data->soc == SOC_ARCH_EXYNOS)
- writel(EXYNOS_TMU_CLEAR_RISE_INT |
- EXYNOS_TMU_CLEAR_FALL_INT,
- data->base + EXYNOS_TMU_REG_INTCLEAR);
- else
- writel(EXYNOS4210_TMU_INTCLEAR_VAL,
- data->base + EXYNOS_TMU_REG_INTCLEAR);
- clk_disable(data->clk);
- mutex_unlock(&data->lock);
-
- enable_irq(data->irq);
-}
-
-static irqreturn_t exynos_tmu_irq(int irq, void *id)
-{
- struct exynos_tmu_data *data = id;
-
- disable_irq_nosync(irq);
- schedule_work(&data->irq_work);
-
- return IRQ_HANDLED;
-}
-static struct thermal_sensor_conf exynos_sensor_conf = {
- .name = "exynos-therm",
- .read_temperature = (int (*)(void *))exynos_tmu_read,
- .write_emul_temp = exynos_tmu_set_emulation,
-};
-
-#if defined(CONFIG_CPU_EXYNOS4210)
-static struct exynos_tmu_platform_data const exynos4210_default_tmu_data = {
- .threshold = 80,
- .trigger_levels[0] = 5,
- .trigger_levels[1] = 20,
- .trigger_levels[2] = 30,
- .trigger_level0_en = 1,
- .trigger_level1_en = 1,
- .trigger_level2_en = 1,
- .trigger_level3_en = 0,
- .gain = 15,
- .reference_voltage = 7,
- .cal_type = TYPE_ONE_POINT_TRIMMING,
- .freq_tab[0] = {
- .freq_clip_max = 800 * 1000,
- .temp_level = 85,
- },
- .freq_tab[1] = {
- .freq_clip_max = 200 * 1000,
- .temp_level = 100,
- },
- .freq_tab_count = 2,
- .type = SOC_ARCH_EXYNOS4210,
-};
-#define EXYNOS4210_TMU_DRV_DATA (&exynos4210_default_tmu_data)
-#else
-#define EXYNOS4210_TMU_DRV_DATA (NULL)
-#endif
-
-#if defined(CONFIG_SOC_EXYNOS5250) || defined(CONFIG_SOC_EXYNOS4412) || \
- defined(CONFIG_SOC_EXYNOS4212)
-static struct exynos_tmu_platform_data const exynos_default_tmu_data = {
- .threshold_falling = 10,
- .trigger_levels[0] = 85,
- .trigger_levels[1] = 103,
- .trigger_levels[2] = 110,
- .trigger_level0_en = 1,
- .trigger_level1_en = 1,
- .trigger_level2_en = 1,
- .trigger_level3_en = 0,
- .gain = 8,
- .reference_voltage = 16,
- .noise_cancel_mode = 4,
- .cal_type = TYPE_ONE_POINT_TRIMMING,
- .efuse_value = 55,
- .freq_tab[0] = {
- .freq_clip_max = 800 * 1000,
- .temp_level = 85,
- },
- .freq_tab[1] = {
- .freq_clip_max = 200 * 1000,
- .temp_level = 103,
- },
- .freq_tab_count = 2,
- .type = SOC_ARCH_EXYNOS,
-};
-#define EXYNOS_TMU_DRV_DATA (&exynos_default_tmu_data)
-#else
-#define EXYNOS_TMU_DRV_DATA (NULL)
-#endif
-
-#ifdef CONFIG_OF
-static const struct of_device_id exynos_tmu_match[] = {
- {
- .compatible = "samsung,exynos4210-tmu",
- .data = (void *)EXYNOS4210_TMU_DRV_DATA,
- },
- {
- .compatible = "samsung,exynos4412-tmu",
- .data = (void *)EXYNOS_TMU_DRV_DATA,
- },
- {
- .compatible = "samsung,exynos5250-tmu",
- .data = (void *)EXYNOS_TMU_DRV_DATA,
- },
- {},
-};
-MODULE_DEVICE_TABLE(of, exynos_tmu_match);
-#endif
-
-static struct platform_device_id exynos_tmu_driver_ids[] = {
- {
- .name = "exynos4210-tmu",
- .driver_data = (kernel_ulong_t)EXYNOS4210_TMU_DRV_DATA,
- },
- {
- .name = "exynos5250-tmu",
- .driver_data = (kernel_ulong_t)EXYNOS_TMU_DRV_DATA,
- },
- { },
-};
-MODULE_DEVICE_TABLE(platform, exynos_tmu_driver_ids);
-
-static inline struct exynos_tmu_platform_data *exynos_get_driver_data(
- struct platform_device *pdev)
-{
-#ifdef CONFIG_OF
- if (pdev->dev.of_node) {
- const struct of_device_id *match;
- match = of_match_node(exynos_tmu_match, pdev->dev.of_node);
- if (!match)
- return NULL;
- return (struct exynos_tmu_platform_data *) match->data;
- }
-#endif
- return (struct exynos_tmu_platform_data *)
- platform_get_device_id(pdev)->driver_data;
-}
-
-static int exynos_tmu_probe(struct platform_device *pdev)
-{
- struct exynos_tmu_data *data;
- struct exynos_tmu_platform_data *pdata = pdev->dev.platform_data;
- int ret, i;
-
- if (!pdata)
- pdata = exynos_get_driver_data(pdev);
-
- if (!pdata) {
- dev_err(&pdev->dev, "No platform init data supplied.\n");
- return -ENODEV;
- }
- data = devm_kzalloc(&pdev->dev, sizeof(struct exynos_tmu_data),
- GFP_KERNEL);
- if (!data) {
- dev_err(&pdev->dev, "Failed to allocate driver structure\n");
- return -ENOMEM;
- }
-
- data->irq = platform_get_irq(pdev, 0);
- if (data->irq < 0) {
- dev_err(&pdev->dev, "Failed to get platform irq\n");
- return data->irq;
- }
-
- INIT_WORK(&data->irq_work, exynos_tmu_work);
-
- data->mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- data->base = devm_ioremap_resource(&pdev->dev, data->mem);
- if (IS_ERR(data->base))
- return PTR_ERR(data->base);
-
- ret = devm_request_irq(&pdev->dev, data->irq, exynos_tmu_irq,
- IRQF_TRIGGER_RISING, "exynos-tmu", data);
- if (ret) {
- dev_err(&pdev->dev, "Failed to request irq: %d\n", data->irq);
- return ret;
- }
-
- data->clk = devm_clk_get(&pdev->dev, "tmu_apbif");
- if (IS_ERR(data->clk)) {
- dev_err(&pdev->dev, "Failed to get clock\n");
- return PTR_ERR(data->clk);
- }
-
- ret = clk_prepare(data->clk);
- if (ret)
- return ret;
-
- if (pdata->type == SOC_ARCH_EXYNOS ||
- pdata->type == SOC_ARCH_EXYNOS4210)
- data->soc = pdata->type;
- else {
- ret = -EINVAL;
- dev_err(&pdev->dev, "Platform not supported\n");
- goto err_clk;
- }
-
- data->pdata = pdata;
- platform_set_drvdata(pdev, data);
- mutex_init(&data->lock);
-
- ret = exynos_tmu_initialize(pdev);
- if (ret) {
- dev_err(&pdev->dev, "Failed to initialize TMU\n");
- goto err_clk;
- }
-
- exynos_tmu_control(pdev, true);
-
- /* Register the sensor with thermal management interface */
- (&exynos_sensor_conf)->private_data = data;
- exynos_sensor_conf.trip_data.trip_count = pdata->trigger_level0_en +
- pdata->trigger_level1_en + pdata->trigger_level2_en +
- pdata->trigger_level3_en;
-
- for (i = 0; i < exynos_sensor_conf.trip_data.trip_count; i++)
- exynos_sensor_conf.trip_data.trip_val[i] =
- pdata->threshold + pdata->trigger_levels[i];
-
- exynos_sensor_conf.trip_data.trigger_falling = pdata->threshold_falling;
-
- exynos_sensor_conf.cooling_data.freq_clip_count =
- pdata->freq_tab_count;
- for (i = 0; i < pdata->freq_tab_count; i++) {
- exynos_sensor_conf.cooling_data.freq_data[i].freq_clip_max =
- pdata->freq_tab[i].freq_clip_max;
- exynos_sensor_conf.cooling_data.freq_data[i].temp_level =
- pdata->freq_tab[i].temp_level;
- }
-
- ret = exynos_register_thermal(&exynos_sensor_conf);
- if (ret) {
- dev_err(&pdev->dev, "Failed to register thermal interface\n");
- goto err_clk;
- }
-
- return 0;
-err_clk:
- clk_unprepare(data->clk);
- return ret;
-}
-
-static int exynos_tmu_remove(struct platform_device *pdev)
-{
- struct exynos_tmu_data *data = platform_get_drvdata(pdev);
-
- exynos_tmu_control(pdev, false);
-
- exynos_unregister_thermal();
-
- clk_unprepare(data->clk);
-
- return 0;
-}
-
-#ifdef CONFIG_PM_SLEEP
-static int exynos_tmu_suspend(struct device *dev)
-{
- exynos_tmu_control(to_platform_device(dev), false);
-
- return 0;
-}
-
-static int exynos_tmu_resume(struct device *dev)
-{
- struct platform_device *pdev = to_platform_device(dev);
-
- exynos_tmu_initialize(pdev);
- exynos_tmu_control(pdev, true);
-
- return 0;
-}
-
-static SIMPLE_DEV_PM_OPS(exynos_tmu_pm,
- exynos_tmu_suspend, exynos_tmu_resume);
-#define EXYNOS_TMU_PM (&exynos_tmu_pm)
-#else
-#define EXYNOS_TMU_PM NULL
-#endif
-
-static struct platform_driver exynos_tmu_driver = {
- .driver = {
- .name = "exynos-tmu",
- .owner = THIS_MODULE,
- .pm = EXYNOS_TMU_PM,
- .of_match_table = of_match_ptr(exynos_tmu_match),
- },
- .probe = exynos_tmu_probe,
- .remove = exynos_tmu_remove,
- .id_table = exynos_tmu_driver_ids,
-};
-
-module_platform_driver(exynos_tmu_driver);
-
-MODULE_DESCRIPTION("EXYNOS TMU Driver");
-MODULE_AUTHOR("Donggeun Kim <dg77.kim@samsung.com>");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:exynos-tmu");
diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c
new file mode 100644
index 000000000000..1d6c801c1eb9
--- /dev/null
+++ b/drivers/thermal/imx_thermal.c
@@ -0,0 +1,541 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/cpu_cooling.h>
+#include <linux/cpufreq.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/thermal.h>
+#include <linux/types.h>
+
+#define REG_SET 0x4
+#define REG_CLR 0x8
+#define REG_TOG 0xc
+
+#define MISC0 0x0150
+#define MISC0_REFTOP_SELBIASOFF (1 << 3)
+
+#define TEMPSENSE0 0x0180
+#define TEMPSENSE0_ALARM_VALUE_SHIFT 20
+#define TEMPSENSE0_ALARM_VALUE_MASK (0xfff << TEMPSENSE0_ALARM_VALUE_SHIFT)
+#define TEMPSENSE0_TEMP_CNT_SHIFT 8
+#define TEMPSENSE0_TEMP_CNT_MASK (0xfff << TEMPSENSE0_TEMP_CNT_SHIFT)
+#define TEMPSENSE0_FINISHED (1 << 2)
+#define TEMPSENSE0_MEASURE_TEMP (1 << 1)
+#define TEMPSENSE0_POWER_DOWN (1 << 0)
+
+#define TEMPSENSE1 0x0190
+#define TEMPSENSE1_MEASURE_FREQ 0xffff
+
+#define OCOTP_ANA1 0x04e0
+
+/* The driver supports 1 passive trip point and 1 critical trip point */
+enum imx_thermal_trip {
+ IMX_TRIP_PASSIVE,
+ IMX_TRIP_CRITICAL,
+ IMX_TRIP_NUM,
+};
+
+/*
+ * It defines the temperature in millicelsius for passive trip point
+ * that will trigger cooling action when crossed.
+ */
+#define IMX_TEMP_PASSIVE 85000
+
+#define IMX_POLLING_DELAY 2000 /* millisecond */
+#define IMX_PASSIVE_DELAY 1000
+
+struct imx_thermal_data {
+ struct thermal_zone_device *tz;
+ struct thermal_cooling_device *cdev;
+ enum thermal_device_mode mode;
+ struct regmap *tempmon;
+ int c1, c2; /* See formula in imx_get_sensor_data() */
+ unsigned long temp_passive;
+ unsigned long temp_critical;
+ unsigned long alarm_temp;
+ unsigned long last_temp;
+ bool irq_enabled;
+ int irq;
+};
+
+static void imx_set_alarm_temp(struct imx_thermal_data *data,
+ signed long alarm_temp)
+{
+ struct regmap *map = data->tempmon;
+ int alarm_value;
+
+ data->alarm_temp = alarm_temp;
+ alarm_value = (alarm_temp - data->c2) / data->c1;
+ regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_ALARM_VALUE_MASK);
+ regmap_write(map, TEMPSENSE0 + REG_SET, alarm_value <<
+ TEMPSENSE0_ALARM_VALUE_SHIFT);
+}
+
+static int imx_get_temp(struct thermal_zone_device *tz, unsigned long *temp)
+{
+ struct imx_thermal_data *data = tz->devdata;
+ struct regmap *map = data->tempmon;
+ unsigned int n_meas;
+ bool wait;
+ u32 val;
+
+ if (data->mode == THERMAL_DEVICE_ENABLED) {
+ /* Check if a measurement is currently in progress */
+ regmap_read(map, TEMPSENSE0, &val);
+ wait = !(val & TEMPSENSE0_FINISHED);
+ } else {
+ /*
+ * Every time we measure the temperature, we will power on the
+ * temperature sensor, enable measurements, take a reading,
+ * disable measurements, power off the temperature sensor.
+ */
+ regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
+ regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_MEASURE_TEMP);
+
+ wait = true;
+ }
+
+ /*
+ * According to the temp sensor designers, it may require up to ~17us
+ * to complete a measurement.
+ */
+ if (wait)
+ usleep_range(20, 50);
+
+ regmap_read(map, TEMPSENSE0, &val);
+
+ if (data->mode != THERMAL_DEVICE_ENABLED) {
+ regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_MEASURE_TEMP);
+ regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_POWER_DOWN);
+ }
+
+ if ((val & TEMPSENSE0_FINISHED) == 0) {
+ dev_dbg(&tz->device, "temp measurement never finished\n");
+ return -EAGAIN;
+ }
+
+ n_meas = (val & TEMPSENSE0_TEMP_CNT_MASK) >> TEMPSENSE0_TEMP_CNT_SHIFT;
+
+ /* See imx_get_sensor_data() for formula derivation */
+ *temp = data->c2 + data->c1 * n_meas;
+
+ /* Update alarm value to next higher trip point */
+ if (data->alarm_temp == data->temp_passive && *temp >= data->temp_passive)
+ imx_set_alarm_temp(data, data->temp_critical);
+ if (data->alarm_temp == data->temp_critical && *temp < data->temp_passive) {
+ imx_set_alarm_temp(data, data->temp_passive);
+ dev_dbg(&tz->device, "thermal alarm off: T < %lu\n",
+ data->alarm_temp / 1000);
+ }
+
+ if (*temp != data->last_temp) {
+ dev_dbg(&tz->device, "millicelsius: %ld\n", *temp);
+ data->last_temp = *temp;
+ }
+
+ /* Reenable alarm IRQ if temperature below alarm temperature */
+ if (!data->irq_enabled && *temp < data->alarm_temp) {
+ data->irq_enabled = true;
+ enable_irq(data->irq);
+ }
+
+ return 0;
+}
+
+static int imx_get_mode(struct thermal_zone_device *tz,
+ enum thermal_device_mode *mode)
+{
+ struct imx_thermal_data *data = tz->devdata;
+
+ *mode = data->mode;
+
+ return 0;
+}
+
+static int imx_set_mode(struct thermal_zone_device *tz,
+ enum thermal_device_mode mode)
+{
+ struct imx_thermal_data *data = tz->devdata;
+ struct regmap *map = data->tempmon;
+
+ if (mode == THERMAL_DEVICE_ENABLED) {
+ tz->polling_delay = IMX_POLLING_DELAY;
+ tz->passive_delay = IMX_PASSIVE_DELAY;
+
+ regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
+ regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_MEASURE_TEMP);
+
+ if (!data->irq_enabled) {
+ data->irq_enabled = true;
+ enable_irq(data->irq);
+ }
+ } else {
+ regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_MEASURE_TEMP);
+ regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_POWER_DOWN);
+
+ tz->polling_delay = 0;
+ tz->passive_delay = 0;
+
+ if (data->irq_enabled) {
+ disable_irq(data->irq);
+ data->irq_enabled = false;
+ }
+ }
+
+ data->mode = mode;
+ thermal_zone_device_update(tz);
+
+ return 0;
+}
+
+static int imx_get_trip_type(struct thermal_zone_device *tz, int trip,
+ enum thermal_trip_type *type)
+{
+ *type = (trip == IMX_TRIP_PASSIVE) ? THERMAL_TRIP_PASSIVE :
+ THERMAL_TRIP_CRITICAL;
+ return 0;
+}
+
+static int imx_get_crit_temp(struct thermal_zone_device *tz,
+ unsigned long *temp)
+{
+ struct imx_thermal_data *data = tz->devdata;
+
+ *temp = data->temp_critical;
+ return 0;
+}
+
+static int imx_get_trip_temp(struct thermal_zone_device *tz, int trip,
+ unsigned long *temp)
+{
+ struct imx_thermal_data *data = tz->devdata;
+
+ *temp = (trip == IMX_TRIP_PASSIVE) ? data->temp_passive :
+ data->temp_critical;
+ return 0;
+}
+
+static int imx_set_trip_temp(struct thermal_zone_device *tz, int trip,
+ unsigned long temp)
+{
+ struct imx_thermal_data *data = tz->devdata;
+
+ if (trip == IMX_TRIP_CRITICAL)
+ return -EPERM;
+
+ if (temp > IMX_TEMP_PASSIVE)
+ return -EINVAL;
+
+ data->temp_passive = temp;
+
+ imx_set_alarm_temp(data, temp);
+
+ return 0;
+}
+
+static int imx_bind(struct thermal_zone_device *tz,
+ struct thermal_cooling_device *cdev)
+{
+ int ret;
+
+ ret = thermal_zone_bind_cooling_device(tz, IMX_TRIP_PASSIVE, cdev,
+ THERMAL_NO_LIMIT,
+ THERMAL_NO_LIMIT);
+ if (ret) {
+ dev_err(&tz->device,
+ "binding zone %s with cdev %s failed:%d\n",
+ tz->type, cdev->type, ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int imx_unbind(struct thermal_zone_device *tz,
+ struct thermal_cooling_device *cdev)
+{
+ int ret;
+
+ ret = thermal_zone_unbind_cooling_device(tz, IMX_TRIP_PASSIVE, cdev);
+ if (ret) {
+ dev_err(&tz->device,
+ "unbinding zone %s with cdev %s failed:%d\n",
+ tz->type, cdev->type, ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct thermal_zone_device_ops imx_tz_ops = {
+ .bind = imx_bind,
+ .unbind = imx_unbind,
+ .get_temp = imx_get_temp,
+ .get_mode = imx_get_mode,
+ .set_mode = imx_set_mode,
+ .get_trip_type = imx_get_trip_type,
+ .get_trip_temp = imx_get_trip_temp,
+ .get_crit_temp = imx_get_crit_temp,
+ .set_trip_temp = imx_set_trip_temp,
+};
+
+static int imx_get_sensor_data(struct platform_device *pdev)
+{
+ struct imx_thermal_data *data = platform_get_drvdata(pdev);
+ struct regmap *map;
+ int t1, t2, n1, n2;
+ int ret;
+ u32 val;
+
+ map = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+ "fsl,tempmon-data");
+ if (IS_ERR(map)) {
+ ret = PTR_ERR(map);
+ dev_err(&pdev->dev, "failed to get sensor regmap: %d\n", ret);
+ return ret;
+ }
+
+ ret = regmap_read(map, OCOTP_ANA1, &val);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to read sensor data: %d\n", ret);
+ return ret;
+ }
+
+ if (val == 0 || val == ~0) {
+ dev_err(&pdev->dev, "invalid sensor calibration data\n");
+ return -EINVAL;
+ }
+
+ /*
+ * Sensor data layout:
+ * [31:20] - sensor value @ 25C
+ * [19:8] - sensor value of hot
+ * [7:0] - hot temperature value
+ */
+ n1 = val >> 20;
+ n2 = (val & 0xfff00) >> 8;
+ t2 = val & 0xff;
+ t1 = 25; /* t1 always 25C */
+
+ /*
+ * Derived from linear interpolation,
+ * Tmeas = T2 + (Nmeas - N2) * (T1 - T2) / (N1 - N2)
+ * We want to reduce this down to the minimum computation necessary
+ * for each temperature read. Also, we want Tmeas in millicelsius
+ * and we don't want to lose precision from integer division. So...
+ * milli_Tmeas = 1000 * T2 + 1000 * (Nmeas - N2) * (T1 - T2) / (N1 - N2)
+ * Let constant c1 = 1000 * (T1 - T2) / (N1 - N2)
+ * milli_Tmeas = (1000 * T2) + c1 * (Nmeas - N2)
+ * milli_Tmeas = (1000 * T2) + (c1 * Nmeas) - (c1 * N2)
+ * Let constant c2 = (1000 * T2) - (c1 * N2)
+ * milli_Tmeas = c2 + (c1 * Nmeas)
+ */
+ data->c1 = 1000 * (t1 - t2) / (n1 - n2);
+ data->c2 = 1000 * t2 - data->c1 * n2;
+
+ /*
+ * Set the default passive cooling trip point to 20 °C below the
+ * maximum die temperature. Can be changed from userspace.
+ */
+ data->temp_passive = 1000 * (t2 - 20);
+
+ /*
+ * The maximum die temperature is t2, let's give 5 °C cushion
+ * for noise and possible temperature rise between measurements.
+ */
+ data->temp_critical = 1000 * (t2 - 5);
+
+ return 0;
+}
+
+static irqreturn_t imx_thermal_alarm_irq(int irq, void *dev)
+{
+ struct imx_thermal_data *data = dev;
+
+ disable_irq_nosync(irq);
+ data->irq_enabled = false;
+
+ return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t imx_thermal_alarm_irq_thread(int irq, void *dev)
+{
+ struct imx_thermal_data *data = dev;
+
+ dev_dbg(&data->tz->device, "THERMAL ALARM: T > %lu\n",
+ data->alarm_temp / 1000);
+
+ thermal_zone_device_update(data->tz);
+
+ return IRQ_HANDLED;
+}
+
+static int imx_thermal_probe(struct platform_device *pdev)
+{
+ struct imx_thermal_data *data;
+ struct cpumask clip_cpus;
+ struct regmap *map;
+ int measure_freq;
+ int ret;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ map = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, "fsl,tempmon");
+ if (IS_ERR(map)) {
+ ret = PTR_ERR(map);
+ dev_err(&pdev->dev, "failed to get tempmon regmap: %d\n", ret);
+ return ret;
+ }
+ data->tempmon = map;
+
+ data->irq = platform_get_irq(pdev, 0);
+ if (data->irq < 0)
+ return data->irq;
+
+ ret = devm_request_threaded_irq(&pdev->dev, data->irq,
+ imx_thermal_alarm_irq, imx_thermal_alarm_irq_thread,
+ 0, "imx_thermal", data);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed to request alarm irq: %d\n", ret);
+ return ret;
+ }
+
+ platform_set_drvdata(pdev, data);
+
+ ret = imx_get_sensor_data(pdev);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to get sensor data\n");
+ return ret;
+ }
+
+ /* Make sure sensor is in known good state for measurements */
+ regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
+ regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_MEASURE_TEMP);
+ regmap_write(map, TEMPSENSE1 + REG_CLR, TEMPSENSE1_MEASURE_FREQ);
+ regmap_write(map, MISC0 + REG_SET, MISC0_REFTOP_SELBIASOFF);
+ regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_POWER_DOWN);
+
+ cpumask_set_cpu(0, &clip_cpus);
+ data->cdev = cpufreq_cooling_register(&clip_cpus);
+ if (IS_ERR(data->cdev)) {
+ ret = PTR_ERR(data->cdev);
+ dev_err(&pdev->dev,
+ "failed to register cpufreq cooling device: %d\n", ret);
+ return ret;
+ }
+
+ data->tz = thermal_zone_device_register("imx_thermal_zone",
+ IMX_TRIP_NUM,
+ BIT(IMX_TRIP_PASSIVE), data,
+ &imx_tz_ops, NULL,
+ IMX_PASSIVE_DELAY,
+ IMX_POLLING_DELAY);
+ if (IS_ERR(data->tz)) {
+ ret = PTR_ERR(data->tz);
+ dev_err(&pdev->dev,
+ "failed to register thermal zone device %d\n", ret);
+ cpufreq_cooling_unregister(data->cdev);
+ return ret;
+ }
+
+ /* Enable measurements at ~ 10 Hz */
+ regmap_write(map, TEMPSENSE1 + REG_CLR, TEMPSENSE1_MEASURE_FREQ);
+ measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */
+ regmap_write(map, TEMPSENSE1 + REG_SET, measure_freq);
+ imx_set_alarm_temp(data, data->temp_passive);
+ regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
+ regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_MEASURE_TEMP);
+
+ data->irq_enabled = true;
+ data->mode = THERMAL_DEVICE_ENABLED;
+
+ return 0;
+}
+
+static int imx_thermal_remove(struct platform_device *pdev)
+{
+ struct imx_thermal_data *data = platform_get_drvdata(pdev);
+ struct regmap *map = data->tempmon;
+
+ /* Disable measurements */
+ regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_POWER_DOWN);
+
+ thermal_zone_device_unregister(data->tz);
+ cpufreq_cooling_unregister(data->cdev);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int imx_thermal_suspend(struct device *dev)
+{
+ struct imx_thermal_data *data = dev_get_drvdata(dev);
+ struct regmap *map = data->tempmon;
+ u32 val;
+
+ regmap_read(map, TEMPSENSE0, &val);
+ if ((val & TEMPSENSE0_POWER_DOWN) == 0) {
+ /*
+ * If a measurement is taking place, wait for a long enough
+ * time for it to finish, and then check again. If it still
+ * does not finish, something must go wrong.
+ */
+ udelay(50);
+ regmap_read(map, TEMPSENSE0, &val);
+ if ((val & TEMPSENSE0_POWER_DOWN) == 0)
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static int imx_thermal_resume(struct device *dev)
+{
+ /* Nothing to do for now */
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(imx_thermal_pm_ops,
+ imx_thermal_suspend, imx_thermal_resume);
+
+static const struct of_device_id of_imx_thermal_match[] = {
+ { .compatible = "fsl,imx6q-tempmon", },
+ { /* end */ }
+};
+
+static struct platform_driver imx_thermal = {
+ .driver = {
+ .name = "imx_thermal",
+ .owner = THIS_MODULE,
+ .pm = &imx_thermal_pm_ops,
+ .of_match_table = of_imx_thermal_match,
+ },
+ .probe = imx_thermal_probe,
+ .remove = imx_thermal_remove,
+};
+module_platform_driver(imx_thermal);
+
+MODULE_AUTHOR("Freescale Semiconductor, Inc.");
+MODULE_DESCRIPTION("Thermal driver for Freescale i.MX SoCs");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:imx-thermal");
diff --git a/drivers/thermal/samsung/Kconfig b/drivers/thermal/samsung/Kconfig
new file mode 100644
index 000000000000..f760389a204c
--- /dev/null
+++ b/drivers/thermal/samsung/Kconfig
@@ -0,0 +1,18 @@
+config EXYNOS_THERMAL
+ tristate "Exynos thermal management unit driver"
+ depends on ARCH_HAS_BANDGAP && OF
+ help
+ If you say yes here you get support for the TMU (Thermal Management
+ Unit) driver for SAMSUNG EXYNOS series of SoCs. This driver initialises
+ the TMU, reports temperature and handles cooling action if defined.
+ This driver uses the Exynos core thermal APIs and TMU configuration
+ data from the supported SoCs.
+
+config EXYNOS_THERMAL_CORE
+ bool "Core thermal framework support for EXYNOS SOCs"
+ depends on EXYNOS_THERMAL
+ help
+ If you say yes here you get support for EXYNOS TMU
+ (Thermal Management Unit) common registration/unregistration
+ functions to the core thermal layer and also to use the generic
+ CPU cooling APIs.
diff --git a/drivers/thermal/samsung/Makefile b/drivers/thermal/samsung/Makefile
new file mode 100644
index 000000000000..c09d83095dc2
--- /dev/null
+++ b/drivers/thermal/samsung/Makefile
@@ -0,0 +1,7 @@
+#
+# Samsung thermal specific Makefile
+#
+obj-$(CONFIG_EXYNOS_THERMAL) += exynos_thermal.o
+exynos_thermal-y := exynos_tmu.o
+exynos_thermal-y += exynos_tmu_data.o
+exynos_thermal-$(CONFIG_EXYNOS_THERMAL_CORE) += exynos_thermal_common.o
diff --git a/drivers/thermal/samsung/exynos_thermal_common.c b/drivers/thermal/samsung/exynos_thermal_common.c
new file mode 100644
index 000000000000..f10a6ad37c06
--- /dev/null
+++ b/drivers/thermal/samsung/exynos_thermal_common.c
@@ -0,0 +1,432 @@
+/*
+ * exynos_thermal_common.c - Samsung EXYNOS common thermal file
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ * Amit Daniel Kachhap <amit.daniel@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#include <linux/cpu_cooling.h>
+#include <linux/err.h>
+#include <linux/slab.h>
+#include <linux/thermal.h>
+
+#include "exynos_thermal_common.h"
+
+struct exynos_thermal_zone {
+ enum thermal_device_mode mode;
+ struct thermal_zone_device *therm_dev;
+ struct thermal_cooling_device *cool_dev[MAX_COOLING_DEVICE];
+ unsigned int cool_dev_size;
+ struct platform_device *exynos4_dev;
+ struct thermal_sensor_conf *sensor_conf;
+ bool bind;
+};
+
+/* Get mode callback functions for thermal zone */
+static int exynos_get_mode(struct thermal_zone_device *thermal,
+ enum thermal_device_mode *mode)
+{
+ struct exynos_thermal_zone *th_zone = thermal->devdata;
+ if (th_zone)
+ *mode = th_zone->mode;
+ return 0;
+}
+
+/* Set mode callback functions for thermal zone */
+static int exynos_set_mode(struct thermal_zone_device *thermal,
+ enum thermal_device_mode mode)
+{
+ struct exynos_thermal_zone *th_zone = thermal->devdata;
+ if (!th_zone) {
+ dev_err(&thermal->device,
+ "thermal zone not registered\n");
+ return 0;
+ }
+
+ mutex_lock(&thermal->lock);
+
+ if (mode == THERMAL_DEVICE_ENABLED &&
+ !th_zone->sensor_conf->trip_data.trigger_falling)
+ thermal->polling_delay = IDLE_INTERVAL;
+ else
+ thermal->polling_delay = 0;
+
+ mutex_unlock(&thermal->lock);
+
+ th_zone->mode = mode;
+ thermal_zone_device_update(thermal);
+ dev_dbg(th_zone->sensor_conf->dev,
+ "thermal polling set for duration=%d msec\n",
+ thermal->polling_delay);
+ return 0;
+}
+
+
+/* Get trip type callback functions for thermal zone */
+static int exynos_get_trip_type(struct thermal_zone_device *thermal, int trip,
+ enum thermal_trip_type *type)
+{
+ struct exynos_thermal_zone *th_zone = thermal->devdata;
+ int max_trip = th_zone->sensor_conf->trip_data.trip_count;
+ int trip_type;
+
+ if (trip < 0 || trip >= max_trip)
+ return -EINVAL;
+
+ trip_type = th_zone->sensor_conf->trip_data.trip_type[trip];
+
+ if (trip_type == SW_TRIP)
+ *type = THERMAL_TRIP_CRITICAL;
+ else if (trip_type == THROTTLE_ACTIVE)
+ *type = THERMAL_TRIP_ACTIVE;
+ else if (trip_type == THROTTLE_PASSIVE)
+ *type = THERMAL_TRIP_PASSIVE;
+ else
+ return -EINVAL;
+
+ return 0;
+}
+
+/* Get trip temperature callback functions for thermal zone */
+static int exynos_get_trip_temp(struct thermal_zone_device *thermal, int trip,
+ unsigned long *temp)
+{
+ struct exynos_thermal_zone *th_zone = thermal->devdata;
+ int max_trip = th_zone->sensor_conf->trip_data.trip_count;
+
+ if (trip < 0 || trip >= max_trip)
+ return -EINVAL;
+
+ *temp = th_zone->sensor_conf->trip_data.trip_val[trip];
+ /* convert the temperature into millicelsius */
+ *temp = *temp * MCELSIUS;
+
+ return 0;
+}
+
+/* Get critical temperature callback functions for thermal zone */
+static int exynos_get_crit_temp(struct thermal_zone_device *thermal,
+ unsigned long *temp)
+{
+ struct exynos_thermal_zone *th_zone = thermal->devdata;
+ int max_trip = th_zone->sensor_conf->trip_data.trip_count;
+ /* Get the temp of highest trip*/
+ return exynos_get_trip_temp(thermal, max_trip - 1, temp);
+}
+
+/* Bind callback functions for thermal zone */
+static int exynos_bind(struct thermal_zone_device *thermal,
+ struct thermal_cooling_device *cdev)
+{
+ int ret = 0, i, tab_size, level;
+ struct freq_clip_table *tab_ptr, *clip_data;
+ struct exynos_thermal_zone *th_zone = thermal->devdata;
+ struct thermal_sensor_conf *data = th_zone->sensor_conf;
+
+ tab_ptr = (struct freq_clip_table *)data->cooling_data.freq_data;
+ tab_size = data->cooling_data.freq_clip_count;
+
+ if (tab_ptr == NULL || tab_size == 0)
+ return 0;
+
+ /* find the cooling device registered*/
+ for (i = 0; i < th_zone->cool_dev_size; i++)
+ if (cdev == th_zone->cool_dev[i])
+ break;
+
+ /* No matching cooling device */
+ if (i == th_zone->cool_dev_size)
+ return 0;
+
+ /* Bind the thermal zone to the cpufreq cooling device */
+ for (i = 0; i < tab_size; i++) {
+ clip_data = (struct freq_clip_table *)&(tab_ptr[i]);
+ level = cpufreq_cooling_get_level(0, clip_data->freq_clip_max);
+ if (level == THERMAL_CSTATE_INVALID)
+ return 0;
+ switch (GET_ZONE(i)) {
+ case MONITOR_ZONE:
+ case WARN_ZONE:
+ if (thermal_zone_bind_cooling_device(thermal, i, cdev,
+ level, 0)) {
+ dev_err(data->dev,
+ "error unbinding cdev inst=%d\n", i);
+ ret = -EINVAL;
+ }
+ th_zone->bind = true;
+ break;
+ default:
+ ret = -EINVAL;
+ }
+ }
+
+ return ret;
+}
+
+/* Unbind callback functions for thermal zone */
+static int exynos_unbind(struct thermal_zone_device *thermal,
+ struct thermal_cooling_device *cdev)
+{
+ int ret = 0, i, tab_size;
+ struct exynos_thermal_zone *th_zone = thermal->devdata;
+ struct thermal_sensor_conf *data = th_zone->sensor_conf;
+
+ if (th_zone->bind == false)
+ return 0;
+
+ tab_size = data->cooling_data.freq_clip_count;
+
+ if (tab_size == 0)
+ return 0;
+
+ /* find the cooling device registered*/
+ for (i = 0; i < th_zone->cool_dev_size; i++)
+ if (cdev == th_zone->cool_dev[i])
+ break;
+
+ /* No matching cooling device */
+ if (i == th_zone->cool_dev_size)
+ return 0;
+
+ /* Bind the thermal zone to the cpufreq cooling device */
+ for (i = 0; i < tab_size; i++) {
+ switch (GET_ZONE(i)) {
+ case MONITOR_ZONE:
+ case WARN_ZONE:
+ if (thermal_zone_unbind_cooling_device(thermal, i,
+ cdev)) {
+ dev_err(data->dev,
+ "error unbinding cdev inst=%d\n", i);
+ ret = -EINVAL;
+ }
+ th_zone->bind = false;
+ break;
+ default:
+ ret = -EINVAL;
+ }
+ }
+ return ret;
+}
+
+/* Get temperature callback functions for thermal zone */
+static int exynos_get_temp(struct thermal_zone_device *thermal,
+ unsigned long *temp)
+{
+ struct exynos_thermal_zone *th_zone = thermal->devdata;
+ void *data;
+
+ if (!th_zone->sensor_conf) {
+ dev_err(&thermal->device,
+ "Temperature sensor not initialised\n");
+ return -EINVAL;
+ }
+ data = th_zone->sensor_conf->driver_data;
+ *temp = th_zone->sensor_conf->read_temperature(data);
+ /* convert the temperature into millicelsius */
+ *temp = *temp * MCELSIUS;
+ return 0;
+}
+
+/* Get temperature callback functions for thermal zone */
+static int exynos_set_emul_temp(struct thermal_zone_device *thermal,
+ unsigned long temp)
+{
+ void *data;
+ int ret = -EINVAL;
+ struct exynos_thermal_zone *th_zone = thermal->devdata;
+
+ if (!th_zone->sensor_conf) {
+ dev_err(&thermal->device,
+ "Temperature sensor not initialised\n");
+ return -EINVAL;
+ }
+ data = th_zone->sensor_conf->driver_data;
+ if (th_zone->sensor_conf->write_emul_temp)
+ ret = th_zone->sensor_conf->write_emul_temp(data, temp);
+ return ret;
+}
+
+/* Get the temperature trend */
+static int exynos_get_trend(struct thermal_zone_device *thermal,
+ int trip, enum thermal_trend *trend)
+{
+ int ret;
+ unsigned long trip_temp;
+
+ ret = exynos_get_trip_temp(thermal, trip, &trip_temp);
+ if (ret < 0)
+ return ret;
+
+ if (thermal->temperature >= trip_temp)
+ *trend = THERMAL_TREND_RAISE_FULL;
+ else
+ *trend = THERMAL_TREND_DROP_FULL;
+
+ return 0;
+}
+/* Operation callback functions for thermal zone */
+static struct thermal_zone_device_ops const exynos_dev_ops = {
+ .bind = exynos_bind,
+ .unbind = exynos_unbind,
+ .get_temp = exynos_get_temp,
+ .set_emul_temp = exynos_set_emul_temp,
+ .get_trend = exynos_get_trend,
+ .get_mode = exynos_get_mode,
+ .set_mode = exynos_set_mode,
+ .get_trip_type = exynos_get_trip_type,
+ .get_trip_temp = exynos_get_trip_temp,
+ .get_crit_temp = exynos_get_crit_temp,
+};
+
+/*
+ * This function may be called from interrupt based temperature sensor
+ * when threshold is changed.
+ */
+void exynos_report_trigger(struct thermal_sensor_conf *conf)
+{
+ unsigned int i;
+ char data[10];
+ char *envp[] = { data, NULL };
+ struct exynos_thermal_zone *th_zone;
+
+ if (!conf || !conf->pzone_data) {
+ pr_err("Invalid temperature sensor configuration data\n");
+ return;
+ }
+
+ th_zone = conf->pzone_data;
+ if (th_zone->therm_dev)
+ return;
+
+ if (th_zone->bind == false) {
+ for (i = 0; i < th_zone->cool_dev_size; i++) {
+ if (!th_zone->cool_dev[i])
+ continue;
+ exynos_bind(th_zone->therm_dev,
+ th_zone->cool_dev[i]);
+ }
+ }
+
+ thermal_zone_device_update(th_zone->therm_dev);
+
+ mutex_lock(&th_zone->therm_dev->lock);
+ /* Find the level for which trip happened */
+ for (i = 0; i < th_zone->sensor_conf->trip_data.trip_count; i++) {
+ if (th_zone->therm_dev->last_temperature <
+ th_zone->sensor_conf->trip_data.trip_val[i] * MCELSIUS)
+ break;
+ }
+
+ if (th_zone->mode == THERMAL_DEVICE_ENABLED &&
+ !th_zone->sensor_conf->trip_data.trigger_falling) {
+ if (i > 0)
+ th_zone->therm_dev->polling_delay = ACTIVE_INTERVAL;
+ else
+ th_zone->therm_dev->polling_delay = IDLE_INTERVAL;
+ }
+
+ snprintf(data, sizeof(data), "%u", i);
+ kobject_uevent_env(&th_zone->therm_dev->device.kobj, KOBJ_CHANGE, envp);
+ mutex_unlock(&th_zone->therm_dev->lock);
+}
+
+/* Register with the in-kernel thermal management */
+int exynos_register_thermal(struct thermal_sensor_conf *sensor_conf)
+{
+ int ret;
+ struct cpumask mask_val;
+ struct exynos_thermal_zone *th_zone;
+
+ if (!sensor_conf || !sensor_conf->read_temperature) {
+ pr_err("Temperature sensor not initialised\n");
+ return -EINVAL;
+ }
+
+ th_zone = devm_kzalloc(sensor_conf->dev,
+ sizeof(struct exynos_thermal_zone), GFP_KERNEL);
+ if (!th_zone)
+ return -ENOMEM;
+
+ th_zone->sensor_conf = sensor_conf;
+ /*
+ * TODO: 1) Handle multiple cooling devices in a thermal zone
+ * 2) Add a flag/name in cooling info to map to specific
+ * sensor
+ */
+ if (sensor_conf->cooling_data.freq_clip_count > 0) {
+ cpumask_set_cpu(0, &mask_val);
+ th_zone->cool_dev[th_zone->cool_dev_size] =
+ cpufreq_cooling_register(&mask_val);
+ if (IS_ERR(th_zone->cool_dev[th_zone->cool_dev_size])) {
+ dev_err(sensor_conf->dev,
+ "Failed to register cpufreq cooling device\n");
+ ret = -EINVAL;
+ goto err_unregister;
+ }
+ th_zone->cool_dev_size++;
+ }
+
+ th_zone->therm_dev = thermal_zone_device_register(
+ sensor_conf->name, sensor_conf->trip_data.trip_count,
+ 0, th_zone, &exynos_dev_ops, NULL, 0,
+ sensor_conf->trip_data.trigger_falling ? 0 :
+ IDLE_INTERVAL);
+
+ if (IS_ERR(th_zone->therm_dev)) {
+ dev_err(sensor_conf->dev,
+ "Failed to register thermal zone device\n");
+ ret = PTR_ERR(th_zone->therm_dev);
+ goto err_unregister;
+ }
+ th_zone->mode = THERMAL_DEVICE_ENABLED;
+ sensor_conf->pzone_data = th_zone;
+
+ dev_info(sensor_conf->dev,
+ "Exynos: Thermal zone(%s) registered\n", sensor_conf->name);
+
+ return 0;
+
+err_unregister:
+ exynos_unregister_thermal(sensor_conf);
+ return ret;
+}
+
+/* Un-Register with the in-kernel thermal management */
+void exynos_unregister_thermal(struct thermal_sensor_conf *sensor_conf)
+{
+ int i;
+ struct exynos_thermal_zone *th_zone;
+
+ if (!sensor_conf || !sensor_conf->pzone_data) {
+ pr_err("Invalid temperature sensor configuration data\n");
+ return;
+ }
+
+ th_zone = sensor_conf->pzone_data;
+
+ if (th_zone->therm_dev)
+ thermal_zone_device_unregister(th_zone->therm_dev);
+
+ for (i = 0; i < th_zone->cool_dev_size; i++) {
+ if (th_zone->cool_dev[i])
+ cpufreq_cooling_unregister(th_zone->cool_dev[i]);
+ }
+
+ dev_info(sensor_conf->dev,
+ "Exynos: Kernel Thermal management unregistered\n");
+}
diff --git a/drivers/thermal/samsung/exynos_thermal_common.h b/drivers/thermal/samsung/exynos_thermal_common.h
new file mode 100644
index 000000000000..3eb2ed9ea3a4
--- /dev/null
+++ b/drivers/thermal/samsung/exynos_thermal_common.h
@@ -0,0 +1,107 @@
+/*
+ * exynos_thermal_common.h - Samsung EXYNOS common header file
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ * Amit Daniel Kachhap <amit.daniel@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#ifndef _EXYNOS_THERMAL_COMMON_H
+#define _EXYNOS_THERMAL_COMMON_H
+
+/* In-kernel thermal framework related macros & definations */
+#define SENSOR_NAME_LEN 16
+#define MAX_TRIP_COUNT 8
+#define MAX_COOLING_DEVICE 4
+#define MAX_THRESHOLD_LEVS 5
+
+#define ACTIVE_INTERVAL 500
+#define IDLE_INTERVAL 10000
+#define MCELSIUS 1000
+
+/* CPU Zone information */
+#define PANIC_ZONE 4
+#define WARN_ZONE 3
+#define MONITOR_ZONE 2
+#define SAFE_ZONE 1
+
+#define GET_ZONE(trip) (trip + 2)
+#define GET_TRIP(zone) (zone - 2)
+
+enum trigger_type {
+ THROTTLE_ACTIVE = 1,
+ THROTTLE_PASSIVE,
+ SW_TRIP,
+ HW_TRIP,
+};
+
+/**
+ * struct freq_clip_table
+ * @freq_clip_max: maximum frequency allowed for this cooling state.
+ * @temp_level: Temperature level at which the temperature clipping will
+ * happen.
+ * @mask_val: cpumask of the allowed cpu's where the clipping will take place.
+ *
+ * This structure is required to be filled and passed to the
+ * cpufreq_cooling_unregister function.
+ */
+struct freq_clip_table {
+ unsigned int freq_clip_max;
+ unsigned int temp_level;
+ const struct cpumask *mask_val;
+};
+
+struct thermal_trip_point_conf {
+ int trip_val[MAX_TRIP_COUNT];
+ int trip_type[MAX_TRIP_COUNT];
+ int trip_count;
+ unsigned char trigger_falling;
+};
+
+struct thermal_cooling_conf {
+ struct freq_clip_table freq_data[MAX_TRIP_COUNT];
+ int freq_clip_count;
+};
+
+struct thermal_sensor_conf {
+ char name[SENSOR_NAME_LEN];
+ int (*read_temperature)(void *data);
+ int (*write_emul_temp)(void *drv_data, unsigned long temp);
+ struct thermal_trip_point_conf trip_data;
+ struct thermal_cooling_conf cooling_data;
+ void *driver_data;
+ void *pzone_data;
+ struct device *dev;
+};
+
+/*Functions used exynos based thermal sensor driver*/
+#ifdef CONFIG_EXYNOS_THERMAL_CORE
+void exynos_unregister_thermal(struct thermal_sensor_conf *sensor_conf);
+int exynos_register_thermal(struct thermal_sensor_conf *sensor_conf);
+void exynos_report_trigger(struct thermal_sensor_conf *sensor_conf);
+#else
+static inline void
+exynos_unregister_thermal(struct thermal_sensor_conf *sensor_conf) { return; }
+
+static inline int
+exynos_register_thermal(struct thermal_sensor_conf *sensor_conf) { return 0; }
+
+static inline void
+exynos_report_trigger(struct thermal_sensor_conf *sensor_conf) { return; }
+
+#endif /* CONFIG_EXYNOS_THERMAL_CORE */
+#endif /* _EXYNOS_THERMAL_COMMON_H */
diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c
new file mode 100644
index 000000000000..b43afda8acd1
--- /dev/null
+++ b/drivers/thermal/samsung/exynos_tmu.c
@@ -0,0 +1,762 @@
+/*
+ * exynos_tmu.c - Samsung EXYNOS TMU (Thermal Management Unit)
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ * Donggeun Kim <dg77.kim@samsung.com>
+ * Amit Daniel Kachhap <amit.kachhap@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+
+#include "exynos_thermal_common.h"
+#include "exynos_tmu.h"
+#include "exynos_tmu_data.h"
+
+/**
+ * struct exynos_tmu_data : A structure to hold the private data of the TMU
+ driver
+ * @id: identifier of the one instance of the TMU controller.
+ * @pdata: pointer to the tmu platform/configuration data
+ * @base: base address of the single instance of the TMU controller.
+ * @base_common: base address of the common registers of the TMU controller.
+ * @irq: irq number of the TMU controller.
+ * @soc: id of the SOC type.
+ * @irq_work: pointer to the irq work structure.
+ * @lock: lock to implement synchronization.
+ * @clk: pointer to the clock structure.
+ * @temp_error1: fused value of the first point trim.
+ * @temp_error2: fused value of the second point trim.
+ * @regulator: pointer to the TMU regulator structure.
+ * @reg_conf: pointer to structure to register with core thermal.
+ */
+struct exynos_tmu_data {
+ int id;
+ struct exynos_tmu_platform_data *pdata;
+ void __iomem *base;
+ void __iomem *base_common;
+ int irq;
+ enum soc_type soc;
+ struct work_struct irq_work;
+ struct mutex lock;
+ struct clk *clk;
+ u8 temp_error1, temp_error2;
+ struct regulator *regulator;
+ struct thermal_sensor_conf *reg_conf;
+};
+
+/*
+ * TMU treats temperature as a mapped temperature code.
+ * The temperature is converted differently depending on the calibration type.
+ */
+static int temp_to_code(struct exynos_tmu_data *data, u8 temp)
+{
+ struct exynos_tmu_platform_data *pdata = data->pdata;
+ int temp_code;
+
+ if (pdata->cal_mode == HW_MODE)
+ return temp;
+
+ if (data->soc == SOC_ARCH_EXYNOS4210)
+ /* temp should range between 25 and 125 */
+ if (temp < 25 || temp > 125) {
+ temp_code = -EINVAL;
+ goto out;
+ }
+
+ switch (pdata->cal_type) {
+ case TYPE_TWO_POINT_TRIMMING:
+ temp_code = (temp - pdata->first_point_trim) *
+ (data->temp_error2 - data->temp_error1) /
+ (pdata->second_point_trim - pdata->first_point_trim) +
+ data->temp_error1;
+ break;
+ case TYPE_ONE_POINT_TRIMMING:
+ temp_code = temp + data->temp_error1 - pdata->first_point_trim;
+ break;
+ default:
+ temp_code = temp + pdata->default_temp_offset;
+ break;
+ }
+out:
+ return temp_code;
+}
+
+/*
+ * Calculate a temperature value from a temperature code.
+ * The unit of the temperature is degree Celsius.
+ */
+static int code_to_temp(struct exynos_tmu_data *data, u8 temp_code)
+{
+ struct exynos_tmu_platform_data *pdata = data->pdata;
+ int temp;
+
+ if (pdata->cal_mode == HW_MODE)
+ return temp_code;
+
+ if (data->soc == SOC_ARCH_EXYNOS4210)
+ /* temp_code should range between 75 and 175 */
+ if (temp_code < 75 || temp_code > 175) {
+ temp = -ENODATA;
+ goto out;
+ }
+
+ switch (pdata->cal_type) {
+ case TYPE_TWO_POINT_TRIMMING:
+ temp = (temp_code - data->temp_error1) *
+ (pdata->second_point_trim - pdata->first_point_trim) /
+ (data->temp_error2 - data->temp_error1) +
+ pdata->first_point_trim;
+ break;
+ case TYPE_ONE_POINT_TRIMMING:
+ temp = temp_code - data->temp_error1 + pdata->first_point_trim;
+ break;
+ default:
+ temp = temp_code - pdata->default_temp_offset;
+ break;
+ }
+out:
+ return temp;
+}
+
+static int exynos_tmu_initialize(struct platform_device *pdev)
+{
+ struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+ struct exynos_tmu_platform_data *pdata = data->pdata;
+ const struct exynos_tmu_registers *reg = pdata->registers;
+ unsigned int status, trim_info = 0, con;
+ unsigned int rising_threshold = 0, falling_threshold = 0;
+ int ret = 0, threshold_code, i, trigger_levs = 0;
+
+ mutex_lock(&data->lock);
+ clk_enable(data->clk);
+
+ if (TMU_SUPPORTS(pdata, READY_STATUS)) {
+ status = readb(data->base + reg->tmu_status);
+ if (!status) {
+ ret = -EBUSY;
+ goto out;
+ }
+ }
+
+ if (TMU_SUPPORTS(pdata, TRIM_RELOAD))
+ __raw_writel(1, data->base + reg->triminfo_ctrl);
+
+ if (pdata->cal_mode == HW_MODE)
+ goto skip_calib_data;
+
+ /* Save trimming info in order to perform calibration */
+ if (data->soc == SOC_ARCH_EXYNOS5440) {
+ /*
+ * For exynos5440 soc triminfo value is swapped between TMU0 and
+ * TMU2, so the below logic is needed.
+ */
+ switch (data->id) {
+ case 0:
+ trim_info = readl(data->base +
+ EXYNOS5440_EFUSE_SWAP_OFFSET + reg->triminfo_data);
+ break;
+ case 1:
+ trim_info = readl(data->base + reg->triminfo_data);
+ break;
+ case 2:
+ trim_info = readl(data->base -
+ EXYNOS5440_EFUSE_SWAP_OFFSET + reg->triminfo_data);
+ }
+ } else {
+ trim_info = readl(data->base + reg->triminfo_data);
+ }
+ data->temp_error1 = trim_info & EXYNOS_TMU_TEMP_MASK;
+ data->temp_error2 = ((trim_info >> reg->triminfo_85_shift) &
+ EXYNOS_TMU_TEMP_MASK);
+
+ if (!data->temp_error1 ||
+ (pdata->min_efuse_value > data->temp_error1) ||
+ (data->temp_error1 > pdata->max_efuse_value))
+ data->temp_error1 = pdata->efuse_value & EXYNOS_TMU_TEMP_MASK;
+
+ if (!data->temp_error2)
+ data->temp_error2 =
+ (pdata->efuse_value >> reg->triminfo_85_shift) &
+ EXYNOS_TMU_TEMP_MASK;
+
+skip_calib_data:
+ if (pdata->max_trigger_level > MAX_THRESHOLD_LEVS) {
+ dev_err(&pdev->dev, "Invalid max trigger level\n");
+ goto out;
+ }
+
+ for (i = 0; i < pdata->max_trigger_level; i++) {
+ if (!pdata->trigger_levels[i])
+ continue;
+
+ if ((pdata->trigger_type[i] == HW_TRIP) &&
+ (!pdata->trigger_levels[pdata->max_trigger_level - 1])) {
+ dev_err(&pdev->dev, "Invalid hw trigger level\n");
+ ret = -EINVAL;
+ goto out;
+ }
+
+ /* Count trigger levels except the HW trip*/
+ if (!(pdata->trigger_type[i] == HW_TRIP))
+ trigger_levs++;
+ }
+
+ if (data->soc == SOC_ARCH_EXYNOS4210) {
+ /* Write temperature code for threshold */
+ threshold_code = temp_to_code(data, pdata->threshold);
+ if (threshold_code < 0) {
+ ret = threshold_code;
+ goto out;
+ }
+ writeb(threshold_code,
+ data->base + reg->threshold_temp);
+ for (i = 0; i < trigger_levs; i++)
+ writeb(pdata->trigger_levels[i], data->base +
+ reg->threshold_th0 + i * sizeof(reg->threshold_th0));
+
+ writel(reg->inten_rise_mask, data->base + reg->tmu_intclear);
+ } else {
+ /* Write temperature code for rising and falling threshold */
+ for (i = 0;
+ i < trigger_levs && i < EXYNOS_MAX_TRIGGER_PER_REG; i++) {
+ threshold_code = temp_to_code(data,
+ pdata->trigger_levels[i]);
+ if (threshold_code < 0) {
+ ret = threshold_code;
+ goto out;
+ }
+ rising_threshold |= threshold_code << 8 * i;
+ if (pdata->threshold_falling) {
+ threshold_code = temp_to_code(data,
+ pdata->trigger_levels[i] -
+ pdata->threshold_falling);
+ if (threshold_code > 0)
+ falling_threshold |=
+ threshold_code << 8 * i;
+ }
+ }
+
+ writel(rising_threshold,
+ data->base + reg->threshold_th0);
+ writel(falling_threshold,
+ data->base + reg->threshold_th1);
+
+ writel((reg->inten_rise_mask << reg->inten_rise_shift) |
+ (reg->inten_fall_mask << reg->inten_fall_shift),
+ data->base + reg->tmu_intclear);
+
+ /* if last threshold limit is also present */
+ i = pdata->max_trigger_level - 1;
+ if (pdata->trigger_levels[i] &&
+ (pdata->trigger_type[i] == HW_TRIP)) {
+ threshold_code = temp_to_code(data,
+ pdata->trigger_levels[i]);
+ if (threshold_code < 0) {
+ ret = threshold_code;
+ goto out;
+ }
+ if (i == EXYNOS_MAX_TRIGGER_PER_REG - 1) {
+ /* 1-4 level to be assigned in th0 reg */
+ rising_threshold |= threshold_code << 8 * i;
+ writel(rising_threshold,
+ data->base + reg->threshold_th0);
+ } else if (i == EXYNOS_MAX_TRIGGER_PER_REG) {
+ /* 5th level to be assigned in th2 reg */
+ rising_threshold =
+ threshold_code << reg->threshold_th3_l0_shift;
+ writel(rising_threshold,
+ data->base + reg->threshold_th2);
+ }
+ con = readl(data->base + reg->tmu_ctrl);
+ con |= (1 << reg->therm_trip_en_shift);
+ writel(con, data->base + reg->tmu_ctrl);
+ }
+ }
+ /*Clear the PMIN in the common TMU register*/
+ if (reg->tmu_pmin && !data->id)
+ writel(0, data->base_common + reg->tmu_pmin);
+out:
+ clk_disable(data->clk);
+ mutex_unlock(&data->lock);
+
+ return ret;
+}
+
+static void exynos_tmu_control(struct platform_device *pdev, bool on)
+{
+ struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+ struct exynos_tmu_platform_data *pdata = data->pdata;
+ const struct exynos_tmu_registers *reg = pdata->registers;
+ unsigned int con, interrupt_en, cal_val;
+
+ mutex_lock(&data->lock);
+ clk_enable(data->clk);
+
+ con = readl(data->base + reg->tmu_ctrl);
+
+ if (pdata->reference_voltage) {
+ con &= ~(reg->buf_vref_sel_mask << reg->buf_vref_sel_shift);
+ con |= pdata->reference_voltage << reg->buf_vref_sel_shift;
+ }
+
+ if (pdata->gain) {
+ con &= ~(reg->buf_slope_sel_mask << reg->buf_slope_sel_shift);
+ con |= (pdata->gain << reg->buf_slope_sel_shift);
+ }
+
+ if (pdata->noise_cancel_mode) {
+ con &= ~(reg->therm_trip_mode_mask <<
+ reg->therm_trip_mode_shift);
+ con |= (pdata->noise_cancel_mode << reg->therm_trip_mode_shift);
+ }
+
+ if (pdata->cal_mode == HW_MODE) {
+ con &= ~(reg->calib_mode_mask << reg->calib_mode_shift);
+ cal_val = 0;
+ switch (pdata->cal_type) {
+ case TYPE_TWO_POINT_TRIMMING:
+ cal_val = 3;
+ break;
+ case TYPE_ONE_POINT_TRIMMING_85:
+ cal_val = 2;
+ break;
+ case TYPE_ONE_POINT_TRIMMING_25:
+ cal_val = 1;
+ break;
+ case TYPE_NONE:
+ break;
+ default:
+ dev_err(&pdev->dev, "Invalid calibration type, using none\n");
+ }
+ con |= cal_val << reg->calib_mode_shift;
+ }
+
+ if (on) {
+ con |= (1 << reg->core_en_shift);
+ interrupt_en =
+ pdata->trigger_enable[3] << reg->inten_rise3_shift |
+ pdata->trigger_enable[2] << reg->inten_rise2_shift |
+ pdata->trigger_enable[1] << reg->inten_rise1_shift |
+ pdata->trigger_enable[0] << reg->inten_rise0_shift;
+ if (TMU_SUPPORTS(pdata, FALLING_TRIP))
+ interrupt_en |=
+ interrupt_en << reg->inten_fall0_shift;
+ } else {
+ con &= ~(1 << reg->core_en_shift);
+ interrupt_en = 0; /* Disable all interrupts */
+ }
+ writel(interrupt_en, data->base + reg->tmu_inten);
+ writel(con, data->base + reg->tmu_ctrl);
+
+ clk_disable(data->clk);
+ mutex_unlock(&data->lock);
+}
+
+static int exynos_tmu_read(struct exynos_tmu_data *data)
+{
+ struct exynos_tmu_platform_data *pdata = data->pdata;
+ const struct exynos_tmu_registers *reg = pdata->registers;
+ u8 temp_code;
+ int temp;
+
+ mutex_lock(&data->lock);
+ clk_enable(data->clk);
+
+ temp_code = readb(data->base + reg->tmu_cur_temp);
+ temp = code_to_temp(data, temp_code);
+
+ clk_disable(data->clk);
+ mutex_unlock(&data->lock);
+
+ return temp;
+}
+
+#ifdef CONFIG_THERMAL_EMULATION
+static int exynos_tmu_set_emulation(void *drv_data, unsigned long temp)
+{
+ struct exynos_tmu_data *data = drv_data;
+ struct exynos_tmu_platform_data *pdata = data->pdata;
+ const struct exynos_tmu_registers *reg = pdata->registers;
+ unsigned int val;
+ int ret = -EINVAL;
+
+ if (!TMU_SUPPORTS(pdata, EMULATION))
+ goto out;
+
+ if (temp && temp < MCELSIUS)
+ goto out;
+
+ mutex_lock(&data->lock);
+ clk_enable(data->clk);
+
+ val = readl(data->base + reg->emul_con);
+
+ if (temp) {
+ temp /= MCELSIUS;
+
+ if (TMU_SUPPORTS(pdata, EMUL_TIME)) {
+ val &= ~(EXYNOS_EMUL_TIME_MASK << reg->emul_time_shift);
+ val |= (EXYNOS_EMUL_TIME << reg->emul_time_shift);
+ }
+ val &= ~(EXYNOS_EMUL_DATA_MASK << reg->emul_temp_shift);
+ val |= (temp_to_code(data, temp) << reg->emul_temp_shift) |
+ EXYNOS_EMUL_ENABLE;
+ } else {
+ val &= ~EXYNOS_EMUL_ENABLE;
+ }
+
+ writel(val, data->base + reg->emul_con);
+
+ clk_disable(data->clk);
+ mutex_unlock(&data->lock);
+ return 0;
+out:
+ return ret;
+}
+#else
+static int exynos_tmu_set_emulation(void *drv_data, unsigned long temp)
+ { return -EINVAL; }
+#endif/*CONFIG_THERMAL_EMULATION*/
+
+static void exynos_tmu_work(struct work_struct *work)
+{
+ struct exynos_tmu_data *data = container_of(work,
+ struct exynos_tmu_data, irq_work);
+ struct exynos_tmu_platform_data *pdata = data->pdata;
+ const struct exynos_tmu_registers *reg = pdata->registers;
+ unsigned int val_irq, val_type;
+
+ /* Find which sensor generated this interrupt */
+ if (reg->tmu_irqstatus) {
+ val_type = readl(data->base_common + reg->tmu_irqstatus);
+ if (!((val_type >> data->id) & 0x1))
+ goto out;
+ }
+
+ exynos_report_trigger(data->reg_conf);
+ mutex_lock(&data->lock);
+ clk_enable(data->clk);
+
+ /* TODO: take action based on particular interrupt */
+ val_irq = readl(data->base + reg->tmu_intstat);
+ /* clear the interrupts */
+ writel(val_irq, data->base + reg->tmu_intclear);
+
+ clk_disable(data->clk);
+ mutex_unlock(&data->lock);
+out:
+ enable_irq(data->irq);
+}
+
+static irqreturn_t exynos_tmu_irq(int irq, void *id)
+{
+ struct exynos_tmu_data *data = id;
+
+ disable_irq_nosync(irq);
+ schedule_work(&data->irq_work);
+
+ return IRQ_HANDLED;
+}
+
+static const struct of_device_id exynos_tmu_match[] = {
+ {
+ .compatible = "samsung,exynos4210-tmu",
+ .data = (void *)EXYNOS4210_TMU_DRV_DATA,
+ },
+ {
+ .compatible = "samsung,exynos4412-tmu",
+ .data = (void *)EXYNOS5250_TMU_DRV_DATA,
+ },
+ {
+ .compatible = "samsung,exynos5250-tmu",
+ .data = (void *)EXYNOS5250_TMU_DRV_DATA,
+ },
+ {
+ .compatible = "samsung,exynos5440-tmu",
+ .data = (void *)EXYNOS5440_TMU_DRV_DATA,
+ },
+ {},
+};
+MODULE_DEVICE_TABLE(of, exynos_tmu_match);
+
+static inline struct exynos_tmu_platform_data *exynos_get_driver_data(
+ struct platform_device *pdev, int id)
+{
+ struct exynos_tmu_init_data *data_table;
+ struct exynos_tmu_platform_data *tmu_data;
+ const struct of_device_id *match;
+
+ match = of_match_node(exynos_tmu_match, pdev->dev.of_node);
+ if (!match)
+ return NULL;
+ data_table = (struct exynos_tmu_init_data *) match->data;
+ if (!data_table || id >= data_table->tmu_count)
+ return NULL;
+ tmu_data = data_table->tmu_data;
+ return (struct exynos_tmu_platform_data *) (tmu_data + id);
+}
+
+static int exynos_map_dt_data(struct platform_device *pdev)
+{
+ struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+ struct exynos_tmu_platform_data *pdata;
+ struct resource res;
+ int ret;
+
+ if (!data || !pdev->dev.of_node)
+ return -ENODEV;
+
+ /*
+ * Try enabling the regulator if found
+ * TODO: Add regulator as an SOC feature, so that regulator enable
+ * is a compulsory call.
+ */
+ data->regulator = devm_regulator_get(&pdev->dev, "vtmu");
+ if (!IS_ERR(data->regulator)) {
+ ret = regulator_enable(data->regulator);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to enable vtmu\n");
+ return ret;
+ }
+ } else {
+ dev_info(&pdev->dev, "Regulator node (vtmu) not found\n");
+ }
+
+ data->id = of_alias_get_id(pdev->dev.of_node, "tmuctrl");
+ if (data->id < 0)
+ data->id = 0;
+
+ data->irq = irq_of_parse_and_map(pdev->dev.of_node, 0);
+ if (data->irq <= 0) {
+ dev_err(&pdev->dev, "failed to get IRQ\n");
+ return -ENODEV;
+ }
+
+ if (of_address_to_resource(pdev->dev.of_node, 0, &res)) {
+ dev_err(&pdev->dev, "failed to get Resource 0\n");
+ return -ENODEV;
+ }
+
+ data->base = devm_ioremap(&pdev->dev, res.start, resource_size(&res));
+ if (!data->base) {
+ dev_err(&pdev->dev, "Failed to ioremap memory\n");
+ return -EADDRNOTAVAIL;
+ }
+
+ pdata = exynos_get_driver_data(pdev, data->id);
+ if (!pdata) {
+ dev_err(&pdev->dev, "No platform init data supplied.\n");
+ return -ENODEV;
+ }
+ data->pdata = pdata;
+ /*
+ * Check if the TMU shares some registers and then try to map the
+ * memory of common registers.
+ */
+ if (!TMU_SUPPORTS(pdata, SHARED_MEMORY))
+ return 0;
+
+ if (of_address_to_resource(pdev->dev.of_node, 1, &res)) {
+ dev_err(&pdev->dev, "failed to get Resource 1\n");
+ return -ENODEV;
+ }
+
+ data->base_common = devm_ioremap(&pdev->dev, res.start,
+ resource_size(&res));
+ if (!data->base_common) {
+ dev_err(&pdev->dev, "Failed to ioremap memory\n");
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
+static int exynos_tmu_probe(struct platform_device *pdev)
+{
+ struct exynos_tmu_data *data;
+ struct exynos_tmu_platform_data *pdata;
+ struct thermal_sensor_conf *sensor_conf;
+ int ret, i;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(struct exynos_tmu_data),
+ GFP_KERNEL);
+ if (!data) {
+ dev_err(&pdev->dev, "Failed to allocate driver structure\n");
+ return -ENOMEM;
+ }
+
+ platform_set_drvdata(pdev, data);
+ mutex_init(&data->lock);
+
+ ret = exynos_map_dt_data(pdev);
+ if (ret)
+ return ret;
+
+ pdata = data->pdata;
+
+ INIT_WORK(&data->irq_work, exynos_tmu_work);
+
+ data->clk = devm_clk_get(&pdev->dev, "tmu_apbif");
+ if (IS_ERR(data->clk)) {
+ dev_err(&pdev->dev, "Failed to get clock\n");
+ return PTR_ERR(data->clk);
+ }
+
+ ret = clk_prepare(data->clk);
+ if (ret)
+ return ret;
+
+ if (pdata->type == SOC_ARCH_EXYNOS ||
+ pdata->type == SOC_ARCH_EXYNOS4210 ||
+ pdata->type == SOC_ARCH_EXYNOS5440)
+ data->soc = pdata->type;
+ else {
+ ret = -EINVAL;
+ dev_err(&pdev->dev, "Platform not supported\n");
+ goto err_clk;
+ }
+
+ ret = exynos_tmu_initialize(pdev);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to initialize TMU\n");
+ goto err_clk;
+ }
+
+ exynos_tmu_control(pdev, true);
+
+ /* Allocate a structure to register with the exynos core thermal */
+ sensor_conf = devm_kzalloc(&pdev->dev,
+ sizeof(struct thermal_sensor_conf), GFP_KERNEL);
+ if (!sensor_conf) {
+ dev_err(&pdev->dev, "Failed to allocate registration struct\n");
+ ret = -ENOMEM;
+ goto err_clk;
+ }
+ sprintf(sensor_conf->name, "therm_zone%d", data->id);
+ sensor_conf->read_temperature = (int (*)(void *))exynos_tmu_read;
+ sensor_conf->write_emul_temp =
+ (int (*)(void *, unsigned long))exynos_tmu_set_emulation;
+ sensor_conf->driver_data = data;
+ sensor_conf->trip_data.trip_count = pdata->trigger_enable[0] +
+ pdata->trigger_enable[1] + pdata->trigger_enable[2]+
+ pdata->trigger_enable[3];
+
+ for (i = 0; i < sensor_conf->trip_data.trip_count; i++) {
+ sensor_conf->trip_data.trip_val[i] =
+ pdata->threshold + pdata->trigger_levels[i];
+ sensor_conf->trip_data.trip_type[i] =
+ pdata->trigger_type[i];
+ }
+
+ sensor_conf->trip_data.trigger_falling = pdata->threshold_falling;
+
+ sensor_conf->cooling_data.freq_clip_count = pdata->freq_tab_count;
+ for (i = 0; i < pdata->freq_tab_count; i++) {
+ sensor_conf->cooling_data.freq_data[i].freq_clip_max =
+ pdata->freq_tab[i].freq_clip_max;
+ sensor_conf->cooling_data.freq_data[i].temp_level =
+ pdata->freq_tab[i].temp_level;
+ }
+ sensor_conf->dev = &pdev->dev;
+ /* Register the sensor with thermal management interface */
+ ret = exynos_register_thermal(sensor_conf);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to register thermal interface\n");
+ goto err_clk;
+ }
+ data->reg_conf = sensor_conf;
+
+ ret = devm_request_irq(&pdev->dev, data->irq, exynos_tmu_irq,
+ IRQF_TRIGGER_RISING | IRQF_SHARED, dev_name(&pdev->dev), data);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to request irq: %d\n", data->irq);
+ goto err_clk;
+ }
+
+ return 0;
+err_clk:
+ clk_unprepare(data->clk);
+ return ret;
+}
+
+static int exynos_tmu_remove(struct platform_device *pdev)
+{
+ struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+
+ exynos_tmu_control(pdev, false);
+
+ exynos_unregister_thermal(data->reg_conf);
+
+ clk_unprepare(data->clk);
+
+ if (!IS_ERR(data->regulator))
+ regulator_disable(data->regulator);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int exynos_tmu_suspend(struct device *dev)
+{
+ exynos_tmu_control(to_platform_device(dev), false);
+
+ return 0;
+}
+
+static int exynos_tmu_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+
+ exynos_tmu_initialize(pdev);
+ exynos_tmu_control(pdev, true);
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(exynos_tmu_pm,
+ exynos_tmu_suspend, exynos_tmu_resume);
+#define EXYNOS_TMU_PM (&exynos_tmu_pm)
+#else
+#define EXYNOS_TMU_PM NULL
+#endif
+
+static struct platform_driver exynos_tmu_driver = {
+ .driver = {
+ .name = "exynos-tmu",
+ .owner = THIS_MODULE,
+ .pm = EXYNOS_TMU_PM,
+ .of_match_table = exynos_tmu_match,
+ },
+ .probe = exynos_tmu_probe,
+ .remove = exynos_tmu_remove,
+};
+
+module_platform_driver(exynos_tmu_driver);
+
+MODULE_DESCRIPTION("EXYNOS TMU Driver");
+MODULE_AUTHOR("Donggeun Kim <dg77.kim@samsung.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:exynos-tmu");
diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h
new file mode 100644
index 000000000000..b364c9eee701
--- /dev/null
+++ b/drivers/thermal/samsung/exynos_tmu.h
@@ -0,0 +1,311 @@
+/*
+ * exynos_tmu.h - Samsung EXYNOS TMU (Thermal Management Unit)
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ * Donggeun Kim <dg77.kim@samsung.com>
+ * Amit Daniel Kachhap <amit.daniel@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef _EXYNOS_TMU_H
+#define _EXYNOS_TMU_H
+#include <linux/cpu_cooling.h>
+
+#include "exynos_thermal_common.h"
+
+enum calibration_type {
+ TYPE_ONE_POINT_TRIMMING,
+ TYPE_ONE_POINT_TRIMMING_25,
+ TYPE_ONE_POINT_TRIMMING_85,
+ TYPE_TWO_POINT_TRIMMING,
+ TYPE_NONE,
+};
+
+enum calibration_mode {
+ SW_MODE,
+ HW_MODE,
+};
+
+enum soc_type {
+ SOC_ARCH_EXYNOS4210 = 1,
+ SOC_ARCH_EXYNOS,
+ SOC_ARCH_EXYNOS5440,
+};
+
+/**
+ * EXYNOS TMU supported features.
+ * TMU_SUPPORT_EMULATION - This features is used to set user defined
+ * temperature to the TMU controller.
+ * TMU_SUPPORT_MULTI_INST - This features denotes that the soc
+ * has many instances of TMU.
+ * TMU_SUPPORT_TRIM_RELOAD - This features shows that trimming can
+ * be reloaded.
+ * TMU_SUPPORT_FALLING_TRIP - This features shows that interrupt can
+ * be registered for falling trips also.
+ * TMU_SUPPORT_READY_STATUS - This feature tells that the TMU current
+ * state(active/idle) can be checked.
+ * TMU_SUPPORT_EMUL_TIME - This features allows to set next temp emulation
+ * sample time.
+ * TMU_SUPPORT_SHARED_MEMORY - This feature tells that the different TMU
+ * sensors shares some common registers.
+ * TMU_SUPPORT - macro to compare the above features with the supplied.
+ */
+#define TMU_SUPPORT_EMULATION BIT(0)
+#define TMU_SUPPORT_MULTI_INST BIT(1)
+#define TMU_SUPPORT_TRIM_RELOAD BIT(2)
+#define TMU_SUPPORT_FALLING_TRIP BIT(3)
+#define TMU_SUPPORT_READY_STATUS BIT(4)
+#define TMU_SUPPORT_EMUL_TIME BIT(5)
+#define TMU_SUPPORT_SHARED_MEMORY BIT(6)
+
+#define TMU_SUPPORTS(a, b) (a->features & TMU_SUPPORT_ ## b)
+
+/**
+ * struct exynos_tmu_register - register descriptors to access registers and
+ * bitfields. The register validity, offsets and bitfield values may vary
+ * slightly across different exynos SOC's.
+ * @triminfo_data: register containing 2 pont trimming data
+ * @triminfo_25_shift: shift bit of the 25 C trim value in triminfo_data reg.
+ * @triminfo_85_shift: shift bit of the 85 C trim value in triminfo_data reg.
+ * @triminfo_ctrl: trim info controller register.
+ * @triminfo_reload_shift: shift of triminfo reload enable bit in triminfo_ctrl
+ reg.
+ * @tmu_ctrl: TMU main controller register.
+ * @buf_vref_sel_shift: shift bits of reference voltage in tmu_ctrl register.
+ * @buf_vref_sel_mask: mask bits of reference voltage in tmu_ctrl register.
+ * @therm_trip_mode_shift: shift bits of tripping mode in tmu_ctrl register.
+ * @therm_trip_mode_mask: mask bits of tripping mode in tmu_ctrl register.
+ * @therm_trip_en_shift: shift bits of tripping enable in tmu_ctrl register.
+ * @buf_slope_sel_shift: shift bits of amplifier gain value in tmu_ctrl
+ register.
+ * @buf_slope_sel_mask: mask bits of amplifier gain value in tmu_ctrl register.
+ * @calib_mode_shift: shift bits of calibration mode value in tmu_ctrl
+ register.
+ * @calib_mode_mask: mask bits of calibration mode value in tmu_ctrl
+ register.
+ * @therm_trip_tq_en_shift: shift bits of thermal trip enable by TQ pin in
+ tmu_ctrl register.
+ * @core_en_shift: shift bits of TMU core enable bit in tmu_ctrl register.
+ * @tmu_status: register drescribing the TMU status.
+ * @tmu_cur_temp: register containing the current temperature of the TMU.
+ * @tmu_cur_temp_shift: shift bits of current temp value in tmu_cur_temp
+ register.
+ * @threshold_temp: register containing the base threshold level.
+ * @threshold_th0: Register containing first set of rising levels.
+ * @threshold_th0_l0_shift: shift bits of level0 threshold temperature.
+ * @threshold_th0_l1_shift: shift bits of level1 threshold temperature.
+ * @threshold_th0_l2_shift: shift bits of level2 threshold temperature.
+ * @threshold_th0_l3_shift: shift bits of level3 threshold temperature.
+ * @threshold_th1: Register containing second set of rising levels.
+ * @threshold_th1_l0_shift: shift bits of level0 threshold temperature.
+ * @threshold_th1_l1_shift: shift bits of level1 threshold temperature.
+ * @threshold_th1_l2_shift: shift bits of level2 threshold temperature.
+ * @threshold_th1_l3_shift: shift bits of level3 threshold temperature.
+ * @threshold_th2: Register containing third set of rising levels.
+ * @threshold_th2_l0_shift: shift bits of level0 threshold temperature.
+ * @threshold_th3: Register containing fourth set of rising levels.
+ * @threshold_th3_l0_shift: shift bits of level0 threshold temperature.
+ * @tmu_inten: register containing the different threshold interrupt
+ enable bits.
+ * @inten_rise_shift: shift bits of all rising interrupt bits.
+ * @inten_rise_mask: mask bits of all rising interrupt bits.
+ * @inten_fall_shift: shift bits of all rising interrupt bits.
+ * @inten_fall_mask: mask bits of all rising interrupt bits.
+ * @inten_rise0_shift: shift bits of rising 0 interrupt bits.
+ * @inten_rise1_shift: shift bits of rising 1 interrupt bits.
+ * @inten_rise2_shift: shift bits of rising 2 interrupt bits.
+ * @inten_rise3_shift: shift bits of rising 3 interrupt bits.
+ * @inten_fall0_shift: shift bits of falling 0 interrupt bits.
+ * @inten_fall1_shift: shift bits of falling 1 interrupt bits.
+ * @inten_fall2_shift: shift bits of falling 2 interrupt bits.
+ * @inten_fall3_shift: shift bits of falling 3 interrupt bits.
+ * @tmu_intstat: Register containing the interrupt status values.
+ * @tmu_intclear: Register for clearing the raised interrupt status.
+ * @emul_con: TMU emulation controller register.
+ * @emul_temp_shift: shift bits of emulation temperature.
+ * @emul_time_shift: shift bits of emulation time.
+ * @emul_time_mask: mask bits of emulation time.
+ * @tmu_irqstatus: register to find which TMU generated interrupts.
+ * @tmu_pmin: register to get/set the Pmin value.
+ */
+struct exynos_tmu_registers {
+ u32 triminfo_data;
+ u32 triminfo_25_shift;
+ u32 triminfo_85_shift;
+
+ u32 triminfo_ctrl;
+ u32 triminfo_reload_shift;
+
+ u32 tmu_ctrl;
+ u32 buf_vref_sel_shift;
+ u32 buf_vref_sel_mask;
+ u32 therm_trip_mode_shift;
+ u32 therm_trip_mode_mask;
+ u32 therm_trip_en_shift;
+ u32 buf_slope_sel_shift;
+ u32 buf_slope_sel_mask;
+ u32 calib_mode_shift;
+ u32 calib_mode_mask;
+ u32 therm_trip_tq_en_shift;
+ u32 core_en_shift;
+
+ u32 tmu_status;
+
+ u32 tmu_cur_temp;
+ u32 tmu_cur_temp_shift;
+
+ u32 threshold_temp;
+
+ u32 threshold_th0;
+ u32 threshold_th0_l0_shift;
+ u32 threshold_th0_l1_shift;
+ u32 threshold_th0_l2_shift;
+ u32 threshold_th0_l3_shift;
+
+ u32 threshold_th1;
+ u32 threshold_th1_l0_shift;
+ u32 threshold_th1_l1_shift;
+ u32 threshold_th1_l2_shift;
+ u32 threshold_th1_l3_shift;
+
+ u32 threshold_th2;
+ u32 threshold_th2_l0_shift;
+
+ u32 threshold_th3;
+ u32 threshold_th3_l0_shift;
+
+ u32 tmu_inten;
+ u32 inten_rise_shift;
+ u32 inten_rise_mask;
+ u32 inten_fall_shift;
+ u32 inten_fall_mask;
+ u32 inten_rise0_shift;
+ u32 inten_rise1_shift;
+ u32 inten_rise2_shift;
+ u32 inten_rise3_shift;
+ u32 inten_fall0_shift;
+ u32 inten_fall1_shift;
+ u32 inten_fall2_shift;
+ u32 inten_fall3_shift;
+
+ u32 tmu_intstat;
+
+ u32 tmu_intclear;
+
+ u32 emul_con;
+ u32 emul_temp_shift;
+ u32 emul_time_shift;
+ u32 emul_time_mask;
+
+ u32 tmu_irqstatus;
+ u32 tmu_pmin;
+};
+
+/**
+ * struct exynos_tmu_platform_data
+ * @threshold: basic temperature for generating interrupt
+ * 25 <= threshold <= 125 [unit: degree Celsius]
+ * @threshold_falling: differntial value for setting threshold
+ * of temperature falling interrupt.
+ * @trigger_levels: array for each interrupt levels
+ * [unit: degree Celsius]
+ * 0: temperature for trigger_level0 interrupt
+ * condition for trigger_level0 interrupt:
+ * current temperature > threshold + trigger_levels[0]
+ * 1: temperature for trigger_level1 interrupt
+ * condition for trigger_level1 interrupt:
+ * current temperature > threshold + trigger_levels[1]
+ * 2: temperature for trigger_level2 interrupt
+ * condition for trigger_level2 interrupt:
+ * current temperature > threshold + trigger_levels[2]
+ * 3: temperature for trigger_level3 interrupt
+ * condition for trigger_level3 interrupt:
+ * current temperature > threshold + trigger_levels[3]
+ * @trigger_type: defines the type of trigger. Possible values are,
+ * THROTTLE_ACTIVE trigger type
+ * THROTTLE_PASSIVE trigger type
+ * SW_TRIP trigger type
+ * HW_TRIP
+ * @trigger_enable[]: array to denote which trigger levels are enabled.
+ * 1 = enable trigger_level[] interrupt,
+ * 0 = disable trigger_level[] interrupt
+ * @max_trigger_level: max trigger level supported by the TMU
+ * @gain: gain of amplifier in the positive-TC generator block
+ * 0 <= gain <= 15
+ * @reference_voltage: reference voltage of amplifier
+ * in the positive-TC generator block
+ * 0 <= reference_voltage <= 31
+ * @noise_cancel_mode: noise cancellation mode
+ * 000, 100, 101, 110 and 111 can be different modes
+ * @type: determines the type of SOC
+ * @efuse_value: platform defined fuse value
+ * @min_efuse_value: minimum valid trimming data
+ * @max_efuse_value: maximum valid trimming data
+ * @first_point_trim: temp value of the first point trimming
+ * @second_point_trim: temp value of the second point trimming
+ * @default_temp_offset: default temperature offset in case of no trimming
+ * @cal_type: calibration type for temperature
+ * @cal_mode: calibration mode for temperature
+ * @freq_clip_table: Table representing frequency reduction percentage.
+ * @freq_tab_count: Count of the above table as frequency reduction may
+ * applicable to only some of the trigger levels.
+ * @registers: Pointer to structure containing all the TMU controller registers
+ * and bitfields shifts and masks.
+ * @features: a bitfield value indicating the features supported in SOC like
+ * emulation, multi instance etc
+ *
+ * This structure is required for configuration of exynos_tmu driver.
+ */
+struct exynos_tmu_platform_data {
+ u8 threshold;
+ u8 threshold_falling;
+ u8 trigger_levels[MAX_TRIP_COUNT];
+ enum trigger_type trigger_type[MAX_TRIP_COUNT];
+ bool trigger_enable[MAX_TRIP_COUNT];
+ u8 max_trigger_level;
+ u8 gain;
+ u8 reference_voltage;
+ u8 noise_cancel_mode;
+
+ u32 efuse_value;
+ u32 min_efuse_value;
+ u32 max_efuse_value;
+ u8 first_point_trim;
+ u8 second_point_trim;
+ u8 default_temp_offset;
+
+ enum calibration_type cal_type;
+ enum calibration_mode cal_mode;
+ enum soc_type type;
+ struct freq_clip_table freq_tab[4];
+ unsigned int freq_tab_count;
+ const struct exynos_tmu_registers *registers;
+ unsigned int features;
+};
+
+/**
+ * struct exynos_tmu_init_data
+ * @tmu_count: number of TMU instances.
+ * @tmu_data: platform data of all TMU instances.
+ * This structure is required to store data for multi-instance exynos tmu
+ * driver.
+ */
+struct exynos_tmu_init_data {
+ int tmu_count;
+ struct exynos_tmu_platform_data tmu_data[];
+};
+
+#endif /* _EXYNOS_TMU_H */
diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c
new file mode 100644
index 000000000000..9002499c1f69
--- /dev/null
+++ b/drivers/thermal/samsung/exynos_tmu_data.c
@@ -0,0 +1,250 @@
+/*
+ * exynos_tmu_data.c - Samsung EXYNOS tmu data file
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ * Amit Daniel Kachhap <amit.daniel@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#include "exynos_thermal_common.h"
+#include "exynos_tmu.h"
+#include "exynos_tmu_data.h"
+
+#if defined(CONFIG_CPU_EXYNOS4210)
+static const struct exynos_tmu_registers exynos4210_tmu_registers = {
+ .triminfo_data = EXYNOS_TMU_REG_TRIMINFO,
+ .triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT,
+ .triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT,
+ .tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
+ .buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT,
+ .buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK,
+ .buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT,
+ .buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK,
+ .core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT,
+ .tmu_status = EXYNOS_TMU_REG_STATUS,
+ .tmu_cur_temp = EXYNOS_TMU_REG_CURRENT_TEMP,
+ .threshold_temp = EXYNOS4210_TMU_REG_THRESHOLD_TEMP,
+ .threshold_th0 = EXYNOS4210_TMU_REG_TRIG_LEVEL0,
+ .tmu_inten = EXYNOS_TMU_REG_INTEN,
+ .inten_rise_mask = EXYNOS4210_TMU_TRIG_LEVEL_MASK,
+ .inten_rise0_shift = EXYNOS_TMU_INTEN_RISE0_SHIFT,
+ .inten_rise1_shift = EXYNOS_TMU_INTEN_RISE1_SHIFT,
+ .inten_rise2_shift = EXYNOS_TMU_INTEN_RISE2_SHIFT,
+ .inten_rise3_shift = EXYNOS_TMU_INTEN_RISE3_SHIFT,
+ .tmu_intstat = EXYNOS_TMU_REG_INTSTAT,
+ .tmu_intclear = EXYNOS_TMU_REG_INTCLEAR,
+};
+
+struct exynos_tmu_init_data const exynos4210_default_tmu_data = {
+ .tmu_data = {
+ {
+ .threshold = 80,
+ .trigger_levels[0] = 5,
+ .trigger_levels[1] = 20,
+ .trigger_levels[2] = 30,
+ .trigger_enable[0] = true,
+ .trigger_enable[1] = true,
+ .trigger_enable[2] = true,
+ .trigger_enable[3] = false,
+ .trigger_type[0] = THROTTLE_ACTIVE,
+ .trigger_type[1] = THROTTLE_ACTIVE,
+ .trigger_type[2] = SW_TRIP,
+ .max_trigger_level = 4,
+ .gain = 15,
+ .reference_voltage = 7,
+ .cal_type = TYPE_ONE_POINT_TRIMMING,
+ .min_efuse_value = 40,
+ .max_efuse_value = 100,
+ .first_point_trim = 25,
+ .second_point_trim = 85,
+ .default_temp_offset = 50,
+ .freq_tab[0] = {
+ .freq_clip_max = 800 * 1000,
+ .temp_level = 85,
+ },
+ .freq_tab[1] = {
+ .freq_clip_max = 200 * 1000,
+ .temp_level = 100,
+ },
+ .freq_tab_count = 2,
+ .type = SOC_ARCH_EXYNOS4210,
+ .registers = &exynos4210_tmu_registers,
+ .features = TMU_SUPPORT_READY_STATUS,
+ },
+ },
+ .tmu_count = 1,
+};
+#endif
+
+#if defined(CONFIG_SOC_EXYNOS5250) || defined(CONFIG_SOC_EXYNOS4412)
+static const struct exynos_tmu_registers exynos5250_tmu_registers = {
+ .triminfo_data = EXYNOS_TMU_REG_TRIMINFO,
+ .triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT,
+ .triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT,
+ .triminfo_ctrl = EXYNOS_TMU_TRIMINFO_CON,
+ .triminfo_reload_shift = EXYNOS_TRIMINFO_RELOAD_SHIFT,
+ .tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
+ .buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT,
+ .buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK,
+ .therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT,
+ .therm_trip_mode_mask = EXYNOS_TMU_TRIP_MODE_MASK,
+ .therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT,
+ .buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT,
+ .buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK,
+ .core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT,
+ .tmu_status = EXYNOS_TMU_REG_STATUS,
+ .tmu_cur_temp = EXYNOS_TMU_REG_CURRENT_TEMP,
+ .threshold_th0 = EXYNOS_THD_TEMP_RISE,
+ .threshold_th1 = EXYNOS_THD_TEMP_FALL,
+ .tmu_inten = EXYNOS_TMU_REG_INTEN,
+ .inten_rise_mask = EXYNOS_TMU_RISE_INT_MASK,
+ .inten_rise_shift = EXYNOS_TMU_RISE_INT_SHIFT,
+ .inten_fall_mask = EXYNOS_TMU_FALL_INT_MASK,
+ .inten_fall_shift = EXYNOS_TMU_FALL_INT_SHIFT,
+ .inten_rise0_shift = EXYNOS_TMU_INTEN_RISE0_SHIFT,
+ .inten_rise1_shift = EXYNOS_TMU_INTEN_RISE1_SHIFT,
+ .inten_rise2_shift = EXYNOS_TMU_INTEN_RISE2_SHIFT,
+ .inten_rise3_shift = EXYNOS_TMU_INTEN_RISE3_SHIFT,
+ .inten_fall0_shift = EXYNOS_TMU_INTEN_FALL0_SHIFT,
+ .tmu_intstat = EXYNOS_TMU_REG_INTSTAT,
+ .tmu_intclear = EXYNOS_TMU_REG_INTCLEAR,
+ .emul_con = EXYNOS_EMUL_CON,
+ .emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT,
+ .emul_time_shift = EXYNOS_EMUL_TIME_SHIFT,
+ .emul_time_mask = EXYNOS_EMUL_TIME_MASK,
+};
+
+#define EXYNOS5250_TMU_DATA \
+ .threshold_falling = 10, \
+ .trigger_levels[0] = 85, \
+ .trigger_levels[1] = 103, \
+ .trigger_levels[2] = 110, \
+ .trigger_levels[3] = 120, \
+ .trigger_enable[0] = true, \
+ .trigger_enable[1] = true, \
+ .trigger_enable[2] = true, \
+ .trigger_enable[3] = false, \
+ .trigger_type[0] = THROTTLE_ACTIVE, \
+ .trigger_type[1] = THROTTLE_ACTIVE, \
+ .trigger_type[2] = SW_TRIP, \
+ .trigger_type[3] = HW_TRIP, \
+ .max_trigger_level = 4, \
+ .gain = 8, \
+ .reference_voltage = 16, \
+ .noise_cancel_mode = 4, \
+ .cal_type = TYPE_ONE_POINT_TRIMMING, \
+ .efuse_value = 55, \
+ .min_efuse_value = 40, \
+ .max_efuse_value = 100, \
+ .first_point_trim = 25, \
+ .second_point_trim = 85, \
+ .default_temp_offset = 50, \
+ .freq_tab[0] = { \
+ .freq_clip_max = 800 * 1000, \
+ .temp_level = 85, \
+ }, \
+ .freq_tab[1] = { \
+ .freq_clip_max = 200 * 1000, \
+ .temp_level = 103, \
+ }, \
+ .freq_tab_count = 2, \
+ .type = SOC_ARCH_EXYNOS, \
+ .registers = &exynos5250_tmu_registers, \
+ .features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_TRIM_RELOAD | \
+ TMU_SUPPORT_FALLING_TRIP | TMU_SUPPORT_READY_STATUS | \
+ TMU_SUPPORT_EMUL_TIME)
+
+struct exynos_tmu_init_data const exynos5250_default_tmu_data = {
+ .tmu_data = {
+ { EXYNOS5250_TMU_DATA },
+ },
+ .tmu_count = 1,
+};
+#endif
+
+#if defined(CONFIG_SOC_EXYNOS5440)
+static const struct exynos_tmu_registers exynos5440_tmu_registers = {
+ .triminfo_data = EXYNOS5440_TMU_S0_7_TRIM,
+ .triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT,
+ .triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT,
+ .tmu_ctrl = EXYNOS5440_TMU_S0_7_CTRL,
+ .buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT,
+ .buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK,
+ .therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT,
+ .therm_trip_mode_mask = EXYNOS_TMU_TRIP_MODE_MASK,
+ .therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT,
+ .buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT,
+ .buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK,
+ .calib_mode_shift = EXYNOS_TMU_CALIB_MODE_SHIFT,
+ .calib_mode_mask = EXYNOS_TMU_CALIB_MODE_MASK,
+ .core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT,
+ .tmu_status = EXYNOS5440_TMU_S0_7_STATUS,
+ .tmu_cur_temp = EXYNOS5440_TMU_S0_7_TEMP,
+ .threshold_th0 = EXYNOS5440_TMU_S0_7_TH0,
+ .threshold_th1 = EXYNOS5440_TMU_S0_7_TH1,
+ .threshold_th2 = EXYNOS5440_TMU_S0_7_TH2,
+ .threshold_th3_l0_shift = EXYNOS5440_TMU_TH_RISE4_SHIFT,
+ .tmu_inten = EXYNOS5440_TMU_S0_7_IRQEN,
+ .inten_rise_mask = EXYNOS5440_TMU_RISE_INT_MASK,
+ .inten_rise_shift = EXYNOS5440_TMU_RISE_INT_SHIFT,
+ .inten_fall_mask = EXYNOS5440_TMU_FALL_INT_MASK,
+ .inten_fall_shift = EXYNOS5440_TMU_FALL_INT_SHIFT,
+ .inten_rise0_shift = EXYNOS5440_TMU_INTEN_RISE0_SHIFT,
+ .inten_rise1_shift = EXYNOS5440_TMU_INTEN_RISE1_SHIFT,
+ .inten_rise2_shift = EXYNOS5440_TMU_INTEN_RISE2_SHIFT,
+ .inten_rise3_shift = EXYNOS5440_TMU_INTEN_RISE3_SHIFT,
+ .inten_fall0_shift = EXYNOS5440_TMU_INTEN_FALL0_SHIFT,
+ .tmu_intstat = EXYNOS5440_TMU_S0_7_IRQ,
+ .tmu_intclear = EXYNOS5440_TMU_S0_7_IRQ,
+ .tmu_irqstatus = EXYNOS5440_TMU_IRQ_STATUS,
+ .emul_con = EXYNOS5440_TMU_S0_7_DEBUG,
+ .emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT,
+ .tmu_pmin = EXYNOS5440_TMU_PMIN,
+};
+
+#define EXYNOS5440_TMU_DATA \
+ .trigger_levels[0] = 100, \
+ .trigger_levels[4] = 105, \
+ .trigger_enable[0] = 1, \
+ .trigger_type[0] = SW_TRIP, \
+ .trigger_type[4] = HW_TRIP, \
+ .max_trigger_level = 5, \
+ .gain = 5, \
+ .reference_voltage = 16, \
+ .noise_cancel_mode = 4, \
+ .cal_type = TYPE_ONE_POINT_TRIMMING, \
+ .cal_mode = 0, \
+ .efuse_value = 0x5b2d, \
+ .min_efuse_value = 16, \
+ .max_efuse_value = 76, \
+ .first_point_trim = 25, \
+ .second_point_trim = 70, \
+ .default_temp_offset = 25, \
+ .type = SOC_ARCH_EXYNOS5440, \
+ .registers = &exynos5440_tmu_registers, \
+ .features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_FALLING_TRIP | \
+ TMU_SUPPORT_MULTI_INST | TMU_SUPPORT_SHARED_MEMORY),
+
+struct exynos_tmu_init_data const exynos5440_default_tmu_data = {
+ .tmu_data = {
+ { EXYNOS5440_TMU_DATA } ,
+ { EXYNOS5440_TMU_DATA } ,
+ { EXYNOS5440_TMU_DATA } ,
+ },
+ .tmu_count = 3,
+};
+#endif
diff --git a/drivers/thermal/samsung/exynos_tmu_data.h b/drivers/thermal/samsung/exynos_tmu_data.h
new file mode 100644
index 000000000000..dc7feb51099b
--- /dev/null
+++ b/drivers/thermal/samsung/exynos_tmu_data.h
@@ -0,0 +1,155 @@
+/*
+ * exynos_tmu_data.h - Samsung EXYNOS tmu data header file
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ * Amit Daniel Kachhap <amit.daniel@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#ifndef _EXYNOS_TMU_DATA_H
+#define _EXYNOS_TMU_DATA_H
+
+/* Exynos generic registers */
+#define EXYNOS_TMU_REG_TRIMINFO 0x0
+#define EXYNOS_TMU_REG_CONTROL 0x20
+#define EXYNOS_TMU_REG_STATUS 0x28
+#define EXYNOS_TMU_REG_CURRENT_TEMP 0x40
+#define EXYNOS_TMU_REG_INTEN 0x70
+#define EXYNOS_TMU_REG_INTSTAT 0x74
+#define EXYNOS_TMU_REG_INTCLEAR 0x78
+
+#define EXYNOS_TMU_TEMP_MASK 0xff
+#define EXYNOS_TMU_REF_VOLTAGE_SHIFT 24
+#define EXYNOS_TMU_REF_VOLTAGE_MASK 0x1f
+#define EXYNOS_TMU_BUF_SLOPE_SEL_MASK 0xf
+#define EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT 8
+#define EXYNOS_TMU_CORE_EN_SHIFT 0
+
+/* Exynos4210 specific registers */
+#define EXYNOS4210_TMU_REG_THRESHOLD_TEMP 0x44
+#define EXYNOS4210_TMU_REG_TRIG_LEVEL0 0x50
+#define EXYNOS4210_TMU_REG_TRIG_LEVEL1 0x54
+#define EXYNOS4210_TMU_REG_TRIG_LEVEL2 0x58
+#define EXYNOS4210_TMU_REG_TRIG_LEVEL3 0x5C
+#define EXYNOS4210_TMU_REG_PAST_TEMP0 0x60
+#define EXYNOS4210_TMU_REG_PAST_TEMP1 0x64
+#define EXYNOS4210_TMU_REG_PAST_TEMP2 0x68
+#define EXYNOS4210_TMU_REG_PAST_TEMP3 0x6C
+
+#define EXYNOS4210_TMU_TRIG_LEVEL0_MASK 0x1
+#define EXYNOS4210_TMU_TRIG_LEVEL1_MASK 0x10
+#define EXYNOS4210_TMU_TRIG_LEVEL2_MASK 0x100
+#define EXYNOS4210_TMU_TRIG_LEVEL3_MASK 0x1000
+#define EXYNOS4210_TMU_TRIG_LEVEL_MASK 0x1111
+#define EXYNOS4210_TMU_INTCLEAR_VAL 0x1111
+
+/* Exynos5250 and Exynos4412 specific registers */
+#define EXYNOS_TMU_TRIMINFO_CON 0x14
+#define EXYNOS_THD_TEMP_RISE 0x50
+#define EXYNOS_THD_TEMP_FALL 0x54
+#define EXYNOS_EMUL_CON 0x80
+
+#define EXYNOS_TRIMINFO_RELOAD_SHIFT 1
+#define EXYNOS_TRIMINFO_25_SHIFT 0
+#define EXYNOS_TRIMINFO_85_SHIFT 8
+#define EXYNOS_TMU_RISE_INT_MASK 0x111
+#define EXYNOS_TMU_RISE_INT_SHIFT 0
+#define EXYNOS_TMU_FALL_INT_MASK 0x111
+#define EXYNOS_TMU_FALL_INT_SHIFT 12
+#define EXYNOS_TMU_CLEAR_RISE_INT 0x111
+#define EXYNOS_TMU_CLEAR_FALL_INT (0x111 << 12)
+#define EXYNOS_TMU_TRIP_MODE_SHIFT 13
+#define EXYNOS_TMU_TRIP_MODE_MASK 0x7
+#define EXYNOS_TMU_THERM_TRIP_EN_SHIFT 12
+#define EXYNOS_TMU_CALIB_MODE_SHIFT 4
+#define EXYNOS_TMU_CALIB_MODE_MASK 0x3
+
+#define EXYNOS_TMU_INTEN_RISE0_SHIFT 0
+#define EXYNOS_TMU_INTEN_RISE1_SHIFT 4
+#define EXYNOS_TMU_INTEN_RISE2_SHIFT 8
+#define EXYNOS_TMU_INTEN_RISE3_SHIFT 12
+#define EXYNOS_TMU_INTEN_FALL0_SHIFT 16
+#define EXYNOS_TMU_INTEN_FALL1_SHIFT 20
+#define EXYNOS_TMU_INTEN_FALL2_SHIFT 24
+
+#define EXYNOS_EMUL_TIME 0x57F0
+#define EXYNOS_EMUL_TIME_MASK 0xffff
+#define EXYNOS_EMUL_TIME_SHIFT 16
+#define EXYNOS_EMUL_DATA_SHIFT 8
+#define EXYNOS_EMUL_DATA_MASK 0xFF
+#define EXYNOS_EMUL_ENABLE 0x1
+
+#define EXYNOS_MAX_TRIGGER_PER_REG 4
+
+/*exynos5440 specific registers*/
+#define EXYNOS5440_TMU_S0_7_TRIM 0x000
+#define EXYNOS5440_TMU_S0_7_CTRL 0x020
+#define EXYNOS5440_TMU_S0_7_DEBUG 0x040
+#define EXYNOS5440_TMU_S0_7_STATUS 0x060
+#define EXYNOS5440_TMU_S0_7_TEMP 0x0f0
+#define EXYNOS5440_TMU_S0_7_TH0 0x110
+#define EXYNOS5440_TMU_S0_7_TH1 0x130
+#define EXYNOS5440_TMU_S0_7_TH2 0x150
+#define EXYNOS5440_TMU_S0_7_EVTEN 0x1F0
+#define EXYNOS5440_TMU_S0_7_IRQEN 0x210
+#define EXYNOS5440_TMU_S0_7_IRQ 0x230
+/* exynos5440 common registers */
+#define EXYNOS5440_TMU_IRQ_STATUS 0x000
+#define EXYNOS5440_TMU_PMIN 0x004
+#define EXYNOS5440_TMU_TEMP 0x008
+
+#define EXYNOS5440_TMU_RISE_INT_MASK 0xf
+#define EXYNOS5440_TMU_RISE_INT_SHIFT 0
+#define EXYNOS5440_TMU_FALL_INT_MASK 0xf
+#define EXYNOS5440_TMU_FALL_INT_SHIFT 4
+#define EXYNOS5440_TMU_INTEN_RISE0_SHIFT 0
+#define EXYNOS5440_TMU_INTEN_RISE1_SHIFT 1
+#define EXYNOS5440_TMU_INTEN_RISE2_SHIFT 2
+#define EXYNOS5440_TMU_INTEN_RISE3_SHIFT 3
+#define EXYNOS5440_TMU_INTEN_FALL0_SHIFT 4
+#define EXYNOS5440_TMU_INTEN_FALL1_SHIFT 5
+#define EXYNOS5440_TMU_INTEN_FALL2_SHIFT 6
+#define EXYNOS5440_TMU_INTEN_FALL3_SHIFT 7
+#define EXYNOS5440_TMU_TH_RISE0_SHIFT 0
+#define EXYNOS5440_TMU_TH_RISE1_SHIFT 8
+#define EXYNOS5440_TMU_TH_RISE2_SHIFT 16
+#define EXYNOS5440_TMU_TH_RISE3_SHIFT 24
+#define EXYNOS5440_TMU_TH_RISE4_SHIFT 24
+#define EXYNOS5440_EFUSE_SWAP_OFFSET 8
+
+#if defined(CONFIG_CPU_EXYNOS4210)
+extern struct exynos_tmu_init_data const exynos4210_default_tmu_data;
+#define EXYNOS4210_TMU_DRV_DATA (&exynos4210_default_tmu_data)
+#else
+#define EXYNOS4210_TMU_DRV_DATA (NULL)
+#endif
+
+#if (defined(CONFIG_SOC_EXYNOS5250) || defined(CONFIG_SOC_EXYNOS4412))
+extern struct exynos_tmu_init_data const exynos5250_default_tmu_data;
+#define EXYNOS5250_TMU_DRV_DATA (&exynos5250_default_tmu_data)
+#else
+#define EXYNOS5250_TMU_DRV_DATA (NULL)
+#endif
+
+#if defined(CONFIG_SOC_EXYNOS5440)
+extern struct exynos_tmu_init_data const exynos5440_default_tmu_data;
+#define EXYNOS5440_TMU_DRV_DATA (&exynos5440_default_tmu_data)
+#else
+#define EXYNOS5440_TMU_DRV_DATA (NULL)
+#endif
+
+#endif /*_EXYNOS_TMU_DATA_H*/
diff --git a/drivers/thermal/step_wise.c b/drivers/thermal/step_wise.c
index 4d4ddae1a991..d89e781b0a18 100644
--- a/drivers/thermal/step_wise.c
+++ b/drivers/thermal/step_wise.c
@@ -51,44 +51,51 @@ static unsigned long get_target_state(struct thermal_instance *instance,
{
struct thermal_cooling_device *cdev = instance->cdev;
unsigned long cur_state;
+ unsigned long next_target;
+ /*
+ * We keep this instance the way it is by default.
+ * Otherwise, we use the current state of the
+ * cdev in use to determine the next_target.
+ */
cdev->ops->get_cur_state(cdev, &cur_state);
+ next_target = instance->target;
switch (trend) {
case THERMAL_TREND_RAISING:
if (throttle) {
- cur_state = cur_state < instance->upper ?
+ next_target = cur_state < instance->upper ?
(cur_state + 1) : instance->upper;
- if (cur_state < instance->lower)
- cur_state = instance->lower;
+ if (next_target < instance->lower)
+ next_target = instance->lower;
}
break;
case THERMAL_TREND_RAISE_FULL:
if (throttle)
- cur_state = instance->upper;
+ next_target = instance->upper;
break;
case THERMAL_TREND_DROPPING:
if (cur_state == instance->lower) {
if (!throttle)
- cur_state = -1;
+ next_target = THERMAL_NO_TARGET;
} else {
- cur_state -= 1;
- if (cur_state > instance->upper)
- cur_state = instance->upper;
+ next_target = cur_state - 1;
+ if (next_target > instance->upper)
+ next_target = instance->upper;
}
break;
case THERMAL_TREND_DROP_FULL:
if (cur_state == instance->lower) {
if (!throttle)
- cur_state = -1;
+ next_target = THERMAL_NO_TARGET;
} else
- cur_state = instance->lower;
+ next_target = instance->lower;
break;
default:
break;
}
- return cur_state;
+ return next_target;
}
static void update_passive_instance(struct thermal_zone_device *tz,
@@ -133,6 +140,9 @@ static void thermal_zone_trip_update(struct thermal_zone_device *tz, int trip)
old_target = instance->target;
instance->target = get_target_state(instance, trend, throttle);
+ if (old_target == instance->target)
+ continue;
+
/* Activate a passive thermal instance */
if (old_target == THERMAL_NO_TARGET &&
instance->target != THERMAL_NO_TARGET)
diff --git a/drivers/thermal/thermal_core.c b/drivers/thermal/thermal_core.c
index 1f02e8edb45c..4962a6aaf295 100644
--- a/drivers/thermal/thermal_core.c
+++ b/drivers/thermal/thermal_core.c
@@ -38,6 +38,7 @@
#include <net/genetlink.h>
#include "thermal_core.h"
+#include "thermal_hwmon.h"
MODULE_AUTHOR("Zhang Rui");
MODULE_DESCRIPTION("Generic thermal management sysfs support");
@@ -201,14 +202,23 @@ static void print_bind_err_msg(struct thermal_zone_device *tz,
}
static void __bind(struct thermal_zone_device *tz, int mask,
- struct thermal_cooling_device *cdev)
+ struct thermal_cooling_device *cdev,
+ unsigned long *limits)
{
int i, ret;
for (i = 0; i < tz->trips; i++) {
if (mask & (1 << i)) {
+ unsigned long upper, lower;
+
+ upper = THERMAL_NO_LIMIT;
+ lower = THERMAL_NO_LIMIT;
+ if (limits) {
+ lower = limits[i * 2];
+ upper = limits[i * 2 + 1];
+ }
ret = thermal_zone_bind_cooling_device(tz, i, cdev,
- THERMAL_NO_LIMIT, THERMAL_NO_LIMIT);
+ upper, lower);
if (ret)
print_bind_err_msg(tz, cdev, ret);
}
@@ -253,7 +263,8 @@ static void bind_cdev(struct thermal_cooling_device *cdev)
if (tzp->tbp[i].match(pos, cdev))
continue;
tzp->tbp[i].cdev = cdev;
- __bind(pos, tzp->tbp[i].trip_mask, cdev);
+ __bind(pos, tzp->tbp[i].trip_mask, cdev,
+ tzp->tbp[i].binding_limits);
}
}
@@ -291,7 +302,8 @@ static void bind_tz(struct thermal_zone_device *tz)
if (tzp->tbp[i].match(tz, pos))
continue;
tzp->tbp[i].cdev = pos;
- __bind(tz, tzp->tbp[i].trip_mask, pos);
+ __bind(tz, tzp->tbp[i].trip_mask, pos,
+ tzp->tbp[i].binding_limits);
}
}
exit:
@@ -859,260 +871,6 @@ thermal_cooling_device_trip_point_show(struct device *dev,
/* Device management */
-#if defined(CONFIG_THERMAL_HWMON)
-
-/* hwmon sys I/F */
-#include <linux/hwmon.h>
-
-/* thermal zone devices with the same type share one hwmon device */
-struct thermal_hwmon_device {
- char type[THERMAL_NAME_LENGTH];
- struct device *device;
- int count;
- struct list_head tz_list;
- struct list_head node;
-};
-
-struct thermal_hwmon_attr {
- struct device_attribute attr;
- char name[16];
-};
-
-/* one temperature input for each thermal zone */
-struct thermal_hwmon_temp {
- struct list_head hwmon_node;
- struct thermal_zone_device *tz;
- struct thermal_hwmon_attr temp_input; /* hwmon sys attr */
- struct thermal_hwmon_attr temp_crit; /* hwmon sys attr */
-};
-
-static LIST_HEAD(thermal_hwmon_list);
-
-static ssize_t
-name_show(struct device *dev, struct device_attribute *attr, char *buf)
-{
- struct thermal_hwmon_device *hwmon = dev_get_drvdata(dev);
- return sprintf(buf, "%s\n", hwmon->type);
-}
-static DEVICE_ATTR(name, 0444, name_show, NULL);
-
-static ssize_t
-temp_input_show(struct device *dev, struct device_attribute *attr, char *buf)
-{
- long temperature;
- int ret;
- struct thermal_hwmon_attr *hwmon_attr
- = container_of(attr, struct thermal_hwmon_attr, attr);
- struct thermal_hwmon_temp *temp
- = container_of(hwmon_attr, struct thermal_hwmon_temp,
- temp_input);
- struct thermal_zone_device *tz = temp->tz;
-
- ret = thermal_zone_get_temp(tz, &temperature);
-
- if (ret)
- return ret;
-
- return sprintf(buf, "%ld\n", temperature);
-}
-
-static ssize_t
-temp_crit_show(struct device *dev, struct device_attribute *attr,
- char *buf)
-{
- struct thermal_hwmon_attr *hwmon_attr
- = container_of(attr, struct thermal_hwmon_attr, attr);
- struct thermal_hwmon_temp *temp
- = container_of(hwmon_attr, struct thermal_hwmon_temp,
- temp_crit);
- struct thermal_zone_device *tz = temp->tz;
- long temperature;
- int ret;
-
- ret = tz->ops->get_trip_temp(tz, 0, &temperature);
- if (ret)
- return ret;
-
- return sprintf(buf, "%ld\n", temperature);
-}
-
-
-static struct thermal_hwmon_device *
-thermal_hwmon_lookup_by_type(const struct thermal_zone_device *tz)
-{
- struct thermal_hwmon_device *hwmon;
-
- mutex_lock(&thermal_list_lock);
- list_for_each_entry(hwmon, &thermal_hwmon_list, node)
- if (!strcmp(hwmon->type, tz->type)) {
- mutex_unlock(&thermal_list_lock);
- return hwmon;
- }
- mutex_unlock(&thermal_list_lock);
-
- return NULL;
-}
-
-/* Find the temperature input matching a given thermal zone */
-static struct thermal_hwmon_temp *
-thermal_hwmon_lookup_temp(const struct thermal_hwmon_device *hwmon,
- const struct thermal_zone_device *tz)
-{
- struct thermal_hwmon_temp *temp;
-
- mutex_lock(&thermal_list_lock);
- list_for_each_entry(temp, &hwmon->tz_list, hwmon_node)
- if (temp->tz == tz) {
- mutex_unlock(&thermal_list_lock);
- return temp;
- }
- mutex_unlock(&thermal_list_lock);
-
- return NULL;
-}
-
-static int
-thermal_add_hwmon_sysfs(struct thermal_zone_device *tz)
-{
- struct thermal_hwmon_device *hwmon;
- struct thermal_hwmon_temp *temp;
- int new_hwmon_device = 1;
- int result;
-
- hwmon = thermal_hwmon_lookup_by_type(tz);
- if (hwmon) {
- new_hwmon_device = 0;
- goto register_sys_interface;
- }
-
- hwmon = kzalloc(sizeof(struct thermal_hwmon_device), GFP_KERNEL);
- if (!hwmon)
- return -ENOMEM;
-
- INIT_LIST_HEAD(&hwmon->tz_list);
- strlcpy(hwmon->type, tz->type, THERMAL_NAME_LENGTH);
- hwmon->device = hwmon_device_register(NULL);
- if (IS_ERR(hwmon->device)) {
- result = PTR_ERR(hwmon->device);
- goto free_mem;
- }
- dev_set_drvdata(hwmon->device, hwmon);
- result = device_create_file(hwmon->device, &dev_attr_name);
- if (result)
- goto free_mem;
-
- register_sys_interface:
- temp = kzalloc(sizeof(struct thermal_hwmon_temp), GFP_KERNEL);
- if (!temp) {
- result = -ENOMEM;
- goto unregister_name;
- }
-
- temp->tz = tz;
- hwmon->count++;
-
- snprintf(temp->temp_input.name, sizeof(temp->temp_input.name),
- "temp%d_input", hwmon->count);
- temp->temp_input.attr.attr.name = temp->temp_input.name;
- temp->temp_input.attr.attr.mode = 0444;
- temp->temp_input.attr.show = temp_input_show;
- sysfs_attr_init(&temp->temp_input.attr.attr);
- result = device_create_file(hwmon->device, &temp->temp_input.attr);
- if (result)
- goto free_temp_mem;
-
- if (tz->ops->get_crit_temp) {
- unsigned long temperature;
- if (!tz->ops->get_crit_temp(tz, &temperature)) {
- snprintf(temp->temp_crit.name,
- sizeof(temp->temp_crit.name),
- "temp%d_crit", hwmon->count);
- temp->temp_crit.attr.attr.name = temp->temp_crit.name;
- temp->temp_crit.attr.attr.mode = 0444;
- temp->temp_crit.attr.show = temp_crit_show;
- sysfs_attr_init(&temp->temp_crit.attr.attr);
- result = device_create_file(hwmon->device,
- &temp->temp_crit.attr);
- if (result)
- goto unregister_input;
- }
- }
-
- mutex_lock(&thermal_list_lock);
- if (new_hwmon_device)
- list_add_tail(&hwmon->node, &thermal_hwmon_list);
- list_add_tail(&temp->hwmon_node, &hwmon->tz_list);
- mutex_unlock(&thermal_list_lock);
-
- return 0;
-
- unregister_input:
- device_remove_file(hwmon->device, &temp->temp_input.attr);
- free_temp_mem:
- kfree(temp);
- unregister_name:
- if (new_hwmon_device) {
- device_remove_file(hwmon->device, &dev_attr_name);
- hwmon_device_unregister(hwmon->device);
- }
- free_mem:
- if (new_hwmon_device)
- kfree(hwmon);
-
- return result;
-}
-
-static void
-thermal_remove_hwmon_sysfs(struct thermal_zone_device *tz)
-{
- struct thermal_hwmon_device *hwmon;
- struct thermal_hwmon_temp *temp;
-
- hwmon = thermal_hwmon_lookup_by_type(tz);
- if (unlikely(!hwmon)) {
- /* Should never happen... */
- dev_dbg(&tz->device, "hwmon device lookup failed!\n");
- return;
- }
-
- temp = thermal_hwmon_lookup_temp(hwmon, tz);
- if (unlikely(!temp)) {
- /* Should never happen... */
- dev_dbg(&tz->device, "temperature input lookup failed!\n");
- return;
- }
-
- device_remove_file(hwmon->device, &temp->temp_input.attr);
- if (tz->ops->get_crit_temp)
- device_remove_file(hwmon->device, &temp->temp_crit.attr);
-
- mutex_lock(&thermal_list_lock);
- list_del(&temp->hwmon_node);
- kfree(temp);
- if (!list_empty(&hwmon->tz_list)) {
- mutex_unlock(&thermal_list_lock);
- return;
- }
- list_del(&hwmon->node);
- mutex_unlock(&thermal_list_lock);
-
- device_remove_file(hwmon->device, &dev_attr_name);
- hwmon_device_unregister(hwmon->device);
- kfree(hwmon);
-}
-#else
-static int
-thermal_add_hwmon_sysfs(struct thermal_zone_device *tz)
-{
- return 0;
-}
-
-static void
-thermal_remove_hwmon_sysfs(struct thermal_zone_device *tz)
-{
-}
-#endif
-
/**
* thermal_zone_bind_cooling_device() - bind a cooling device to a thermal zone
* @tz: pointer to struct thermal_zone_device
@@ -1715,9 +1473,11 @@ struct thermal_zone_device *thermal_zone_device_register(const char *type,
mutex_unlock(&thermal_governor_lock);
- result = thermal_add_hwmon_sysfs(tz);
- if (result)
- goto unregister;
+ if (!tz->tzp || !tz->tzp->no_hwmon) {
+ result = thermal_add_hwmon_sysfs(tz);
+ if (result)
+ goto unregister;
+ }
mutex_lock(&thermal_list_lock);
list_add_tail(&tz->node, &thermal_tz_list);
diff --git a/drivers/thermal/thermal_hwmon.c b/drivers/thermal/thermal_hwmon.c
new file mode 100644
index 000000000000..eeef0e2498ca
--- /dev/null
+++ b/drivers/thermal/thermal_hwmon.c
@@ -0,0 +1,269 @@
+/*
+ * thermal_hwmon.c - Generic Thermal Management hwmon support.
+ *
+ * Code based on Intel thermal_core.c. Copyrights of the original code:
+ * Copyright (C) 2008 Intel Corp
+ * Copyright (C) 2008 Zhang Rui <rui.zhang@intel.com>
+ * Copyright (C) 2008 Sujith Thomas <sujith.thomas@intel.com>
+ *
+ * Copyright (C) 2013 Texas Instruments
+ * Copyright (C) 2013 Eduardo Valentin <eduardo.valentin@ti.com>
+ * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
+ *
+ * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ */
+#include <linux/hwmon.h>
+#include <linux/thermal.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include "thermal_hwmon.h"
+
+/* hwmon sys I/F */
+/* thermal zone devices with the same type share one hwmon device */
+struct thermal_hwmon_device {
+ char type[THERMAL_NAME_LENGTH];
+ struct device *device;
+ int count;
+ struct list_head tz_list;
+ struct list_head node;
+};
+
+struct thermal_hwmon_attr {
+ struct device_attribute attr;
+ char name[16];
+};
+
+/* one temperature input for each thermal zone */
+struct thermal_hwmon_temp {
+ struct list_head hwmon_node;
+ struct thermal_zone_device *tz;
+ struct thermal_hwmon_attr temp_input; /* hwmon sys attr */
+ struct thermal_hwmon_attr temp_crit; /* hwmon sys attr */
+};
+
+static LIST_HEAD(thermal_hwmon_list);
+
+static DEFINE_MUTEX(thermal_hwmon_list_lock);
+
+static ssize_t
+name_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct thermal_hwmon_device *hwmon = dev_get_drvdata(dev);
+ return sprintf(buf, "%s\n", hwmon->type);
+}
+static DEVICE_ATTR(name, 0444, name_show, NULL);
+
+static ssize_t
+temp_input_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ long temperature;
+ int ret;
+ struct thermal_hwmon_attr *hwmon_attr
+ = container_of(attr, struct thermal_hwmon_attr, attr);
+ struct thermal_hwmon_temp *temp
+ = container_of(hwmon_attr, struct thermal_hwmon_temp,
+ temp_input);
+ struct thermal_zone_device *tz = temp->tz;
+
+ ret = thermal_zone_get_temp(tz, &temperature);
+
+ if (ret)
+ return ret;
+
+ return sprintf(buf, "%ld\n", temperature);
+}
+
+static ssize_t
+temp_crit_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct thermal_hwmon_attr *hwmon_attr
+ = container_of(attr, struct thermal_hwmon_attr, attr);
+ struct thermal_hwmon_temp *temp
+ = container_of(hwmon_attr, struct thermal_hwmon_temp,
+ temp_crit);
+ struct thermal_zone_device *tz = temp->tz;
+ long temperature;
+ int ret;
+
+ ret = tz->ops->get_trip_temp(tz, 0, &temperature);
+ if (ret)
+ return ret;
+
+ return sprintf(buf, "%ld\n", temperature);
+}
+
+
+static struct thermal_hwmon_device *
+thermal_hwmon_lookup_by_type(const struct thermal_zone_device *tz)
+{
+ struct thermal_hwmon_device *hwmon;
+
+ mutex_lock(&thermal_hwmon_list_lock);
+ list_for_each_entry(hwmon, &thermal_hwmon_list, node)
+ if (!strcmp(hwmon->type, tz->type)) {
+ mutex_unlock(&thermal_hwmon_list_lock);
+ return hwmon;
+ }
+ mutex_unlock(&thermal_hwmon_list_lock);
+
+ return NULL;
+}
+
+/* Find the temperature input matching a given thermal zone */
+static struct thermal_hwmon_temp *
+thermal_hwmon_lookup_temp(const struct thermal_hwmon_device *hwmon,
+ const struct thermal_zone_device *tz)
+{
+ struct thermal_hwmon_temp *temp;
+
+ mutex_lock(&thermal_hwmon_list_lock);
+ list_for_each_entry(temp, &hwmon->tz_list, hwmon_node)
+ if (temp->tz == tz) {
+ mutex_unlock(&thermal_hwmon_list_lock);
+ return temp;
+ }
+ mutex_unlock(&thermal_hwmon_list_lock);
+
+ return NULL;
+}
+
+int thermal_add_hwmon_sysfs(struct thermal_zone_device *tz)
+{
+ struct thermal_hwmon_device *hwmon;
+ struct thermal_hwmon_temp *temp;
+ int new_hwmon_device = 1;
+ int result;
+
+ hwmon = thermal_hwmon_lookup_by_type(tz);
+ if (hwmon) {
+ new_hwmon_device = 0;
+ goto register_sys_interface;
+ }
+
+ hwmon = kzalloc(sizeof(*hwmon), GFP_KERNEL);
+ if (!hwmon)
+ return -ENOMEM;
+
+ INIT_LIST_HEAD(&hwmon->tz_list);
+ strlcpy(hwmon->type, tz->type, THERMAL_NAME_LENGTH);
+ hwmon->device = hwmon_device_register(&tz->device);
+ if (IS_ERR(hwmon->device)) {
+ result = PTR_ERR(hwmon->device);
+ goto free_mem;
+ }
+ dev_set_drvdata(hwmon->device, hwmon);
+ result = device_create_file(hwmon->device, &dev_attr_name);
+ if (result)
+ goto free_mem;
+
+ register_sys_interface:
+ temp = kzalloc(sizeof(*temp), GFP_KERNEL);
+ if (!temp) {
+ result = -ENOMEM;
+ goto unregister_name;
+ }
+
+ temp->tz = tz;
+ hwmon->count++;
+
+ snprintf(temp->temp_input.name, sizeof(temp->temp_input.name),
+ "temp%d_input", hwmon->count);
+ temp->temp_input.attr.attr.name = temp->temp_input.name;
+ temp->temp_input.attr.attr.mode = 0444;
+ temp->temp_input.attr.show = temp_input_show;
+ sysfs_attr_init(&temp->temp_input.attr.attr);
+ result = device_create_file(hwmon->device, &temp->temp_input.attr);
+ if (result)
+ goto free_temp_mem;
+
+ if (tz->ops->get_crit_temp) {
+ unsigned long temperature;
+ if (!tz->ops->get_crit_temp(tz, &temperature)) {
+ snprintf(temp->temp_crit.name,
+ sizeof(temp->temp_crit.name),
+ "temp%d_crit", hwmon->count);
+ temp->temp_crit.attr.attr.name = temp->temp_crit.name;
+ temp->temp_crit.attr.attr.mode = 0444;
+ temp->temp_crit.attr.show = temp_crit_show;
+ sysfs_attr_init(&temp->temp_crit.attr.attr);
+ result = device_create_file(hwmon->device,
+ &temp->temp_crit.attr);
+ if (result)
+ goto unregister_input;
+ }
+ }
+
+ mutex_lock(&thermal_hwmon_list_lock);
+ if (new_hwmon_device)
+ list_add_tail(&hwmon->node, &thermal_hwmon_list);
+ list_add_tail(&temp->hwmon_node, &hwmon->tz_list);
+ mutex_unlock(&thermal_hwmon_list_lock);
+
+ return 0;
+
+ unregister_input:
+ device_remove_file(hwmon->device, &temp->temp_input.attr);
+ free_temp_mem:
+ kfree(temp);
+ unregister_name:
+ if (new_hwmon_device) {
+ device_remove_file(hwmon->device, &dev_attr_name);
+ hwmon_device_unregister(hwmon->device);
+ }
+ free_mem:
+ if (new_hwmon_device)
+ kfree(hwmon);
+
+ return result;
+}
+
+void thermal_remove_hwmon_sysfs(struct thermal_zone_device *tz)
+{
+ struct thermal_hwmon_device *hwmon;
+ struct thermal_hwmon_temp *temp;
+
+ hwmon = thermal_hwmon_lookup_by_type(tz);
+ if (unlikely(!hwmon)) {
+ /* Should never happen... */
+ dev_dbg(&tz->device, "hwmon device lookup failed!\n");
+ return;
+ }
+
+ temp = thermal_hwmon_lookup_temp(hwmon, tz);
+ if (unlikely(!temp)) {
+ /* Should never happen... */
+ dev_dbg(&tz->device, "temperature input lookup failed!\n");
+ return;
+ }
+
+ device_remove_file(hwmon->device, &temp->temp_input.attr);
+ if (tz->ops->get_crit_temp)
+ device_remove_file(hwmon->device, &temp->temp_crit.attr);
+
+ mutex_lock(&thermal_hwmon_list_lock);
+ list_del(&temp->hwmon_node);
+ kfree(temp);
+ if (!list_empty(&hwmon->tz_list)) {
+ mutex_unlock(&thermal_hwmon_list_lock);
+ return;
+ }
+ list_del(&hwmon->node);
+ mutex_unlock(&thermal_hwmon_list_lock);
+
+ device_remove_file(hwmon->device, &dev_attr_name);
+ hwmon_device_unregister(hwmon->device);
+ kfree(hwmon);
+}
diff --git a/drivers/thermal/thermal_hwmon.h b/drivers/thermal/thermal_hwmon.h
new file mode 100644
index 000000000000..c798fdb2ae43
--- /dev/null
+++ b/drivers/thermal/thermal_hwmon.h
@@ -0,0 +1,49 @@
+/*
+ * thermal_hwmon.h - Generic Thermal Management hwmon support.
+ *
+ * Code based on Intel thermal_core.c. Copyrights of the original code:
+ * Copyright (C) 2008 Intel Corp
+ * Copyright (C) 2008 Zhang Rui <rui.zhang@intel.com>
+ * Copyright (C) 2008 Sujith Thomas <sujith.thomas@intel.com>
+ *
+ * Copyright (C) 2013 Texas Instruments
+ * Copyright (C) 2013 Eduardo Valentin <eduardo.valentin@ti.com>
+ * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
+ *
+ * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ */
+#ifndef __THERMAL_HWMON_H__
+#define __THERMAL_HWMON_H__
+
+#include <linux/thermal.h>
+
+#ifdef CONFIG_THERMAL_HWMON
+int thermal_add_hwmon_sysfs(struct thermal_zone_device *tz);
+void thermal_remove_hwmon_sysfs(struct thermal_zone_device *tz);
+#else
+static int
+thermal_add_hwmon_sysfs(struct thermal_zone_device *tz)
+{
+ return 0;
+}
+
+static void
+thermal_remove_hwmon_sysfs(struct thermal_zone_device *tz)
+{
+}
+#endif
+
+#endif /* __THERMAL_HWMON_H__ */
diff --git a/drivers/thermal/ti-soc-thermal/dra752-thermal-data.c b/drivers/thermal/ti-soc-thermal/dra752-thermal-data.c
index e5d8326a54d6..a4929272074f 100644
--- a/drivers/thermal/ti-soc-thermal/dra752-thermal-data.c
+++ b/drivers/thermal/ti-soc-thermal/dra752-thermal-data.c
@@ -42,6 +42,7 @@ dra752_core_temp_sensor_registers = {
.mask_hot_mask = DRA752_BANDGAP_CTRL_1_MASK_HOT_CORE_MASK,
.mask_cold_mask = DRA752_BANDGAP_CTRL_1_MASK_COLD_CORE_MASK,
.mask_sidlemode_mask = DRA752_BANDGAP_CTRL_1_SIDLEMODE_MASK,
+ .mask_counter_delay_mask = DRA752_BANDGAP_CTRL_1_COUNTER_DELAY_MASK,
.mask_freeze_mask = DRA752_BANDGAP_CTRL_1_FREEZE_CORE_MASK,
.mask_clear_mask = DRA752_BANDGAP_CTRL_1_CLEAR_CORE_MASK,
.mask_clear_accum_mask = DRA752_BANDGAP_CTRL_1_CLEAR_ACCUM_CORE_MASK,
@@ -77,6 +78,7 @@ dra752_iva_temp_sensor_registers = {
.mask_hot_mask = DRA752_BANDGAP_CTRL_2_MASK_HOT_IVA_MASK,
.mask_cold_mask = DRA752_BANDGAP_CTRL_2_MASK_COLD_IVA_MASK,
.mask_sidlemode_mask = DRA752_BANDGAP_CTRL_1_SIDLEMODE_MASK,
+ .mask_counter_delay_mask = DRA752_BANDGAP_CTRL_1_COUNTER_DELAY_MASK,
.mask_freeze_mask = DRA752_BANDGAP_CTRL_2_FREEZE_IVA_MASK,
.mask_clear_mask = DRA752_BANDGAP_CTRL_2_CLEAR_IVA_MASK,
.mask_clear_accum_mask = DRA752_BANDGAP_CTRL_2_CLEAR_ACCUM_IVA_MASK,
@@ -112,6 +114,7 @@ dra752_mpu_temp_sensor_registers = {
.mask_hot_mask = DRA752_BANDGAP_CTRL_1_MASK_HOT_MPU_MASK,
.mask_cold_mask = DRA752_BANDGAP_CTRL_1_MASK_COLD_MPU_MASK,
.mask_sidlemode_mask = DRA752_BANDGAP_CTRL_1_SIDLEMODE_MASK,
+ .mask_counter_delay_mask = DRA752_BANDGAP_CTRL_1_COUNTER_DELAY_MASK,
.mask_freeze_mask = DRA752_BANDGAP_CTRL_1_FREEZE_MPU_MASK,
.mask_clear_mask = DRA752_BANDGAP_CTRL_1_CLEAR_MPU_MASK,
.mask_clear_accum_mask = DRA752_BANDGAP_CTRL_1_CLEAR_ACCUM_MPU_MASK,
@@ -147,6 +150,7 @@ dra752_dspeve_temp_sensor_registers = {
.mask_hot_mask = DRA752_BANDGAP_CTRL_2_MASK_HOT_DSPEVE_MASK,
.mask_cold_mask = DRA752_BANDGAP_CTRL_2_MASK_COLD_DSPEVE_MASK,
.mask_sidlemode_mask = DRA752_BANDGAP_CTRL_1_SIDLEMODE_MASK,
+ .mask_counter_delay_mask = DRA752_BANDGAP_CTRL_1_COUNTER_DELAY_MASK,
.mask_freeze_mask = DRA752_BANDGAP_CTRL_2_FREEZE_DSPEVE_MASK,
.mask_clear_mask = DRA752_BANDGAP_CTRL_2_CLEAR_DSPEVE_MASK,
.mask_clear_accum_mask = DRA752_BANDGAP_CTRL_2_CLEAR_ACCUM_DSPEVE_MASK,
@@ -182,6 +186,7 @@ dra752_gpu_temp_sensor_registers = {
.mask_hot_mask = DRA752_BANDGAP_CTRL_1_MASK_HOT_GPU_MASK,
.mask_cold_mask = DRA752_BANDGAP_CTRL_1_MASK_COLD_GPU_MASK,
.mask_sidlemode_mask = DRA752_BANDGAP_CTRL_1_SIDLEMODE_MASK,
+ .mask_counter_delay_mask = DRA752_BANDGAP_CTRL_1_COUNTER_DELAY_MASK,
.mask_freeze_mask = DRA752_BANDGAP_CTRL_1_FREEZE_GPU_MASK,
.mask_clear_mask = DRA752_BANDGAP_CTRL_1_CLEAR_GPU_MASK,
.mask_clear_accum_mask = DRA752_BANDGAP_CTRL_1_CLEAR_ACCUM_GPU_MASK,
diff --git a/drivers/thermal/ti-soc-thermal/ti-bandgap.c b/drivers/thermal/ti-soc-thermal/ti-bandgap.c
index 9dfd47196e63..74c0e3474d6e 100644
--- a/drivers/thermal/ti-soc-thermal/ti-bandgap.c
+++ b/drivers/thermal/ti-soc-thermal/ti-bandgap.c
@@ -1020,9 +1020,13 @@ int ti_bandgap_get_trend(struct ti_bandgap *bgp, int id, int *trend)
/* Fetch the update interval */
ret = ti_bandgap_read_update_interval(bgp, id, &interval);
- if (ret || !interval)
+ if (ret)
goto unfreeze;
+ /* Set the interval to 1 ms if bandgap counter delay is not set */
+ if (interval == 0)
+ interval = 1;
+
*trend = (t1 - t2) / interval;
dev_dbg(bgp->dev, "The temperatures are t1 = %d and t2 = %d and trend =%d\n",
diff --git a/drivers/thermal/ti-soc-thermal/ti-thermal-common.c b/drivers/thermal/ti-soc-thermal/ti-thermal-common.c
index 4c5f55c37349..4f8b9af54a5a 100644
--- a/drivers/thermal/ti-soc-thermal/ti-thermal-common.c
+++ b/drivers/thermal/ti-soc-thermal/ti-thermal-common.c
@@ -174,6 +174,9 @@ static int ti_thermal_set_mode(struct thermal_zone_device *thermal,
enum thermal_device_mode mode)
{
struct ti_thermal_data *data = thermal->devdata;
+ struct ti_bandgap *bgp;
+
+ bgp = data->bgp;
if (!data->ti_thermal) {
dev_notice(&thermal->device, "thermal zone not registered\n");
@@ -190,6 +193,8 @@ static int ti_thermal_set_mode(struct thermal_zone_device *thermal,
mutex_unlock(&data->ti_thermal->lock);
data->mode = mode;
+ ti_bandgap_write_update_interval(bgp, data->sensor_id,
+ data->ti_thermal->polling_delay);
thermal_zone_device_update(data->ti_thermal);
dev_dbg(&thermal->device, "thermal polling set for duration=%d msec\n",
data->ti_thermal->polling_delay);
@@ -313,6 +318,8 @@ int ti_thermal_expose_sensor(struct ti_bandgap *bgp, int id,
}
data->ti_thermal->polling_delay = FAST_TEMP_MONITORING_RATE;
ti_bandgap_set_sensor_data(bgp, id, data);
+ ti_bandgap_write_update_interval(bgp, data->sensor_id,
+ data->ti_thermal->polling_delay);
return 0;
}